Used Broaching for sale (203)

Condition: used, BROACHING MACHINE Tsdpfx Aet Hr Dfsa Ioc

Condition: used, Indexing table 400 mm hand Full set of tooling included (guide bars etc) Table bore 10 - 130 mm Key width from 2 - 32 mm Feed rate 0,5 - 5 M/Min; Table 690 x 460mm Table load: 2000 Ram adjustment:0 - 425mm Length: 1300mm Width: 1100mm Height: 1400mm Weight: 1800kg transport can be arranged Tedpfxjz D I Rms Aa Ijc

Condition: used, functionality: fully functional, Year of construction: 2019, machine/vehicle number: 53, overall weight: 38,500 kg, input voltage: 400 V, input current: 355 A, input frequency: 50 Hz, broaching speed: 12 m/min, workpiece diameter (max.): 225 mm, total length: 7,100 mm, total width: 11,560 mm, total height: 6,000 mm, Forst RISH 60 x 2125 x 630 – Vertical internal broaching machine Used Forst broaching machine for internal broaching of ring gear workpieces. The machine features a lifting table and a servo-electric broaching drive; the broach pitch is set via the NC program. Machining is performed individually or in pairs, depending on the workpiece. Identification Manufacturer: Forst Technologie GmbH & Co. KG Type: RISH 60 x 2125 x 630 Factory number: 53 Forst order number: M233202 Reference / Inventory number: 351024 Year of manufacture: 2019 (according to machine data sheet) Technical data according to machine documentation - Maximum tensile force: 600 kN - Maximum stroke: 2,125 mm - Maximum cutting speed: 12 m/min - Return stroke speed: 20 m/min - Maximum workpiece diameter: 225 mm - Maximum workpiece height: 50 mm - Maximum tool diameter: 200 mm - Tool shank diameter: 80 mm - Tool tip diameter: 75 mm - Overall dimensions (L x W x H): approx. 7,100 x 11,560 x 6,000 mm - Total weight of the machine: approx. 38,500 kg - Weight of the base machine: approx. 34,500 kg - Electrical connection: 400 V, 3 phases, 50 Hz - Rated current according to nameplate: 355 A Tjdpfx Aaez Hq Ako Isc Documented features - Siemens SINUMERIK 840D sl / S7-300 - Operator panel OP012 and hand-held operating unit HT8 - SKF roller screw drive and linear guides - Hydraulic workpiece clamping - Coolant system with high/low pressure supply and 1,800-liter tank - Chip conveyor and chip centrifuge - Oil mist separator and central lubrication system Operating manual and technical documentation are available. The data and features listed describe the documented machine condition. The actual scope of supply should be agreed upon before finalization. The suitability for other workpieces requires a technical assessment and, if necessary, adapted tools and fixtures. Used machine, operated without malfunctions until disassembly. Price on request.

Condition: like new (used), functionality: fully functional, Year of construction: 2020, operating hours: 50 h, overall weight: 640 kg, input voltage: 400 V, input frequency: 50 Hz, workpiece diameter (max.): 400 mm, de machine is in nieuwstaat. neem contact op voor meer info. Tedpfx Aozugnhja Ijc

Condition: used, Artrhur Klink RSH1 - 1250 Broach Grinder 09.2009 , new 1979, Table 200 x 1800, Electro mag 200 x 600, with related tooling/accessories, no cabinet. Tsdpfxjzc Iq Io Aa Isc

Condition: refurbished (used), functionality: fully functional, Year of construction: 1988, machine/vehicle number: 3615/673, input voltage: 400 V, input frequency: 50 Hz, broaching length: 1,000 mm, number of broaching positions: 1, broaching speed: 3 m/min, reverse speed: 3 mm/s, total length: 750 mm, total width: 800 mm, total height: 2,250 mm, -WR 177- Manufacturer: Rausch Model: RS3 /1000 Tsdez Hl U Iepfx Aa Isc Machine No.: 3615/673 Year of Manufacture: 1988 Weight: 350kg Overhaul: 04/2025 by Wiemers AG General / Technical Data: Unused, partially overhauled, mechanical vertical broaching machine Rausch RS 3 without CE marking Pulling force: 3,000kg Broaching speeds: 3m/min Return speed: 3m/min Maximum stroke: 1000mm Maximum tool length: 1200mm Table size / work area: 430mm x 320mm / 340mm x 220mm Table through-hole: Ø 90mm for standard broaching mandrels "System Rausch" Workpiece diameter: any (with the cabin removed) Broaching capacity / keyway width: up to 18mm in steel (from 16mm keyway width only with offset tool shank) Dimensions (h x w x d): 2,250mm x 800mm x 750mm (h = including 3-sided protective cabin) Motor: 3.0kw / Power supply: 400V / 50 Hz Equipment: - Protective door with safety monitoring (emergency stop circuit) - Chip chute - Externally adjustable tool length adjustment system (System Rausch) - Protective cover for stroke adjustment and electrical switching units - Electrical sensing of the clamping jaws (System Rausch) (Tool removal control to prevent unintentional retraction of the drawbar, providing additional safety for the operator & tool) - Integrated coolant system - 4-sided enclosed splash guard hood with protective door - Extra reinforced chip basket and chip sieve with magnet insert - Control panel external - 2 grease points for the trapezoidal spindle drive with manual grease gun directly on the spindle nut Note: The machine has been partially overhauled by Rausch. The following wear parts have been replaced and renewed. - New trapezoidal spindles and spindle nuts made of cast, wear-resistant bronze - All bearings and seals are new - New electrical system - 4-sided enclosed splash guard hood with protective door at the front - New protective door instead of the light barrier in the machine room - New clamping jaws - All sheet metal parts, such as covers, chip chute, basket, sieve and spindle protection, are new. - External control panel General The double spindle drive ensures a smooth and central pulling point as well as a constant broaching speed. The machine is primarily designed for the production of keyways up to 18mm. (from 16mm keyway tools only with offset tool shanks) Due to its design, the machine can be quickly and easily set up for broaching with flat broaching tools for keyways. Due to the structurally universal design of the drawbar and the machine table, broaching with profile and flat broaching tools is possible without the use of additional draw heads.

Condition: used, Year of construction: 2008, functionality: fully functional, machine/vehicle number: serie nr 3149, overall weight: 11,800 kg, total width: 6,615 mm, total length: 8,890 mm, total height: 2,050 mm, spindle diameter: 50 mm, type of input current: three-phase, space requirement length: 16,000 mm, space requirement width: 8,000 mm, milling spindle length: 650 mm, compressed air connection: 8 bar, spindle speed (min.): 3,500 rpm, spindle speed (max.): 3,500 rpm, length stop: 3,450 mm, input voltage: 125 V, power: 65 kW (88.38 HP), main saw diameter: 450 mm, corner unit for window and door frames, including tools. controlled from the office (Groeneveld). interpolation (angled pins). barcode laser. return transport. documentation available. complete sets of spare blades/saws, including router bits, linked to Groeneveld. automatic counter-piece. maximum workpiece length 6000. sticker printer for barcode. automatic waxelite pump. automatic central lubrication. connections for pin holes and counter-molds. automatic length stop and rotation for workpieces. including extraction pipes with automatic valve. thicknesses from 38 to 150 mm. Tsdpfx Aasztptqo Iec pin bank: 1x saw blade 40mm. 2x pin shaft 50x650. 2x edge breaker 30x40. router: 1x rounding router 30x40. 3x router bits 50x600. machine can be picked up here; in conjunction with Bos Machines (dismantling and transport not included in the price). price excludes VAT.

Condition: ready for operation (used), functionality: fully functional, HAHNDORF, Type SEW 52/300mm / Keyway Broaching Machine - Keyway broaching machine suitable for broaching internal keyways in gears, pulleys, or hubs. - Broaching length, stroke max. 300mm - Keyway width max. 32mm - Cutting speed 5 meters/minute - Return speed approx. 5 meters/minute - Clamping plates / table diameter approx. 380 x 300 mm Tjdpfszw Idcox Aa Ijc - Smallest bore with special broaching tool 6mm - With broaching inserts 20mm - With standard broaching tool 60mm - Drive power 1.1 KW - Broaching tool with broaching insert - Connection cable Dimensions: L x W x H 1.2 x 0.6 x 1.6 meters / Weight 350 kg Errors and omissions excepted.

Condition: refurbished (used), functionality: fully functional, Year of construction: 2024, broaching length: 1,000 mm, number of broaching positions: 1, broaching speed: 3 m/min, Manufacturer: Rausch (Haan/Rhld) Model: RS 6/1000 Machine No.: 51261 Year of Manufacture: 1978 Weight: 680 kg Overhauled: 11/2024 by Wiemers AG General Information / Technical Data: Overhauled mechanical vertical broaching machine Rausch RS 6 G Pulling force: 60 kN Broaching speeds: 3 m/min and 6 m/min Return speed: 6 m/min Maximum stroke: 1000 mm Maximum tool length: 1200 mm Table dimensions / Working area: 610 x 470 mm / 520 x 320 mm Table aperture: Ø90 mm for standard broaching mandrels Workpiece diameter: unlimited Dimensions (H x W x D): 2,250 mm x 850 mm x 1,200 mm (H = table height from floor, without attachments) Motor: 4.4 kW / 5.5 kW Power supply: 400 Volt / 50 Hz Additional modifications/upgrades to the original machine performed: - External stroke adjustment - New, machine-independent, reproducible tool length adjustment system - Additional limit switches for end position monitoring - Safety door with monitoring (integrated in the emergency circuit) - Machine enclosure below safety door with chip protection and tool storage area - Electrical sensing of clamping jaws (tool removal monitoring to prevent unintended retraction of the broaching bridge) - Coolant swing system with solenoid valve operated during swing motion (for switching on coolant before broaching stroke – optical flow control ensures lubrication, no dry cutting!) - Routing of electrical cables in protective steel conduits - Heavy-duty control cabinet mounting for machine components - Additional oil-proof drip tray on the control cabinet - Three-sided closed splash guard cabin (W = 960 x D = 450 x H = 590 mm) - Reinforced chip screen with magnetic separator - Control panel made of stainless steel with durable labeling - 4 central lubrication points for trapezoidal spindle drive Remarks: The machine has been completely overhauled, the machine body fully refurbished. All wear parts have been replaced. - New trapezoidal spindles and spindle nuts made from cast wear-resistant bronze - All bearings and seals renewed - The coolant system (pump, solenoid valve, and drain tap), including the coolant/lubrication swing system, is new - The clamping jaws are new - Complete electrical system (control cabinet) is new - All sheet metal and enclosures are new - The following components have been overhauled and re-used: - Machine base - Machine column - Machine table with table insert - Broaching bridge (clamping jaws new) - Gear wheels - Electric motor (new brake, new bearings) The machine is stored in our warehouse and can be inspected under power. The attached images are original photos of the machine. The machine is CE marked. Tsdpfx Aew Ighioa Isc The CE marking corresponds to the status as of 1998 (first overhaul).

Condition: good (used), Year of construction: 2004, machine/vehicle number: 3234, (Please tell us your offer price) Sale only within Europe, incl. Turkey Price without packaging; delivery condition: FCA (machine location) ===== Tedozluyajpfx Aa Ijc Technical data see handout. All warranty rights are excluded. For the correctness of the technical data and year of construction, for the completeness of accessories and tool equipment, and for compliance with all safety and environmental protection requirements specified in the accident prevention regulations. No sale to private individuals. Sales only within Europe, incl. Turkey Price without packaging; Delivery condition: FCA (machine location) ===== Technical data please see handout in attachment. German text leading language. Without any guaranty and warranty, including completeness of tools & accessories as well as environmental and safety regulations. No private sales.

Condition: used, A used Elbe keyway milling machine. Todpfxjz H Nw Hj Aa Iec

Condition: like new (used), functionality: fully functional, Year of construction: 2025, overall weight: 370 kg, power: 3.5 kW (4.76 HP), input voltage: 400 V, input frequency: 50 Hz, broaching length: 800 mm, broaching speed: 3 m/min, total length: 920 mm, total width: 800 mm, total height: 1,950 mm, Manufacturer: Rausch (Haan/ Rhld) Model: RS 3 G/800 Machine No.: 2968/424 Year of manufacture: 1970 Weight: 370kg Overhaul: 8/2025 by Wiemers AG Our Ref. / Machine No.: WAG 787 General / Technical Data: Unused, overhauled mechanical vertical broaching machine by Rausch Pulling force: 3,000kg (30kN) Broaching speeds: 3m/min and 6m/min Return speed: 3m/min Maximum stroke: 800mm Maximum tool length: 1,000mm Table size / working surface: 340mm x 220mm / 430mm x 310mm Table opening: Ø 90mm for standard broaching mandrels Workpiece diameter: unlimited (without spray guard cabin) Dimensions (h x w x d): 1,950mm x 820mm x 900mm (h = table height from floor without attachments) Motor: 3.5kW Power supply: 400 Volt / 50 Hz Accessories / Special Features: Tjdeytvyxepfx Aa Ijc - Modified drive system with geared motor and toothed belt drive - 2 broaching speeds: 3m/min & 6m/min - External stroke adjustment, cross-machine reproducible tool length adjustment system - Integrated coolant unit with check valve and drain cock, including selector switch for automatic operation (does not automatically switch in swivel mode) - Patented coolant/lubricant swivel system - Three-sided enclosed, front-open spray guard cabin (no external operator panel) - Machine enclosure below the safety door with chip guard and tool storage area - Electrical cabling within steel protective conduits - Electrical jaw monitoring (tool removal control to prevent unintended retraction of the pull bridge) - Safety door with integrated emergency stop function - Control panel made from stainless steel sheet with permanent marking - 4 central lubrication points for the trapezoidal spindle drive - Machine documentation Remarks: The machine is fully overhauled, with the frame completely refurbished. The following wear parts have been replaced: - New trapezoidal spindles and spindle nuts made from cast wear-resistant bronze - All bearings and seals replaced - Central drive shaft is new - Coolant system (pump, check valve and drain cock), including coolant/lubricant swivel system, is new - Jaws are new (pull bridge additionally reinforced) - A switchable jaw monitoring system has been installed (additional safety for operators and to prevent tool breakage) - A safety door with interlock has been installed instead of the rubber reach-in protection - Tool length adjustment system relocated outside the machine compartment - Additional limit switches installed - Complete electrical system (control cabinet) with Siemens components is new - Control panel made of stainless steel with durable labeling - New geared drive motor (SEW) with toothed belt drive - Machine has been repainted with 2-component structural paint The machine is stored at our warehouse and can be inspected under power.

Year of construction: 1968, condition: used, functionality: fully functional, machine/vehicle number: 2276, Karl Klink HW 20 Reaming Machine For sale is a functional Karl Klink HW 20 reaming machine. This machine comes from the renowned Karl Klink tool machine factory and was used in industrial applications until recently. It is suitable for precise reaming operations in single-part and series production. Technical Data Manufacturer: Karl Klink Tool Machine Factory Model: HW 20 Machine Type: Reaming Machine Year of Manufacture: 1968 Weight: approx. 5,500 kg Connected Load: approx. 19 kVA Condition Fully functional Used Inspection possible by appointment Sale due to changes in equipment Delivery Tsdszvf Tropfx Aa Isc FCA location Dismantling and transport by the buyer Overhead crane and forklift can be made available for loading upon agreement.

Condition: ready for operation (used), functionality: fully functional, overall weight: 2,200 kg, total length: 2,500 mm, total width: 500 mm, total height: 1,200 mm, Spline broaching machine (internal broaching machine) VEB Maschinenfabrik "John Schehr", Meuselwitz, year of manufacture approx. 1955, with extensive accessories Condition: functional Year of manufacture: approx. 1955 Location: West Saxony Price: €3,000 (negotiable) Technical data: Manufacturer: VEB Maschinenfabrik "John Schehr", Meuselwitz, Leipzig district Manufacturing number: 6171 Total weight: approx. 2.2 t Broaching length: approx. 1,000 mm Type of current: three-phase, 50 Hz Operating voltage: 220 V Accessories: Extensive stock of broaching tools (various spline shapes/sizes) available Tsdpfx Ajzyl E Nja Iec Description: For sale is a historical spline broaching machine (horizontal internal broaching machine) from VEB Maschinenfabrik "John Schehr", Meuselwitz – a well-established, internationally recognized East German machine tool manufacturer. The machine is used to broach splines (e.g. keyways) in bores using broaching tools and has a broaching length of approximately 1,000 mm. The scope of delivery includes an extensive stock of broaching tools in various designs – a significant added value, as corresponding tools are hardly available on the market anymore. The machine is functional. Inspection and functional testing at the location in West Saxony are possible by arrangement. Price: €3,000 (negotiable) Other machines available from site liquidation Site takeover negotiable

Condition: good (used), Square broaching tool, multi-slot broaching needle, broaching tool, broaching needle, slotting tool, slotting tool, push broaching needle, keyway push broaching needle -Manufacturer: Forestry, clearing needle, push clearing needle -Quantity: 2 pieces still available -Keyway width: 10 mm Tedpfxozlgb No Aa Ioc -Type: see photos -Submission/Price: complete -Transport dimensions: 1085/33/H32 mm -Weight: 4.5 kg

Condition: not inspected (used), Year of construction: 1988, Clamping plate: 595 x 445 mm Stroke length: 400 mm Stroke: 400 mm Machine weight approx.: 1,600 t Space requirement approx.: 1,400 x 1,200 x 1,500 mm Smallest/Largest cutting speed: 0 - 20 m/min Smallest/Largest return speed: 40 m/min Largest workpiece diameter according to DIN 6885 (boring): 230 mm Tsdpfx Aaoznbrhe Isc

Condition: used, Drawing machine / stretching machine KARL KLINK RSI 2.5 EH -Pulling force 2500 kg -Stretching speed 1 mm to 9 mm/min (infinitely variable) -Stroke length 800 mm -Max. workpiece diameter approx. 250 mm -Motor power approx. 3 kW -Coolant system -Pulling force indicator -Pulling force limitation -Various guide bushings (see pictures) -Machine feet Dimensions: L x W x H 1.1 x 0.7 x 2 meters / Weight 1600 kg Tjdpfxszwdrve Aa Ijc Errors and omissions excepted.

Condition: ready for operation (used), Keyway cutting machine FRÖMAG RAPIDA 463 incl. INDEXING TABLE - Machinable keyway width: 3 - 63mm - Maximum keyway length: 600mm - INDEXING TABLE - For bores from 10 - 500mm - Feed rate: 0.01 - 0.25mm - Cutting speed, infinitely adjustable: 2 - 22 meters/min - Return speed / constant: 50 meters/min - Load capacity max. 3000 kg - Connection power: 4.6 kW - Includes work platform - Various keyway cutters / accessories & tool cabinet Tedpfx Aszl Aiija Ioc Dimensions: L x W x H 1.6 x 1.5 x 2.3 meters / Weight 3500 kg Errors and omissions excepted.

Condition: ready for operation (used), Pulling machine RAUSCH RS 6-1300 with extensive accessories Tjdpfxjza U Alo Aa Isc -Ram stroke / pulling length 1300mm -Pulling force 6000kg -Incl. 38x clearing pins -Incl. 95x guide bushings -Work bench -Setting plates -Crane -Platform -2x tool cabinets Dimensions: L x W x H 1.6 x 1.7 x 2.3 meters / Weight: 2500kg Errors and omissions excepted.

Condition: ready for operation (used), Vertical thread-rolling machine HENNING 03E -Henning - Metzingen -Year of manufacture 1981 -Rolling length approx. 1100mm -Motor power 3KW -Coolant system Dimensions L x W x H 0.7 x 0.5 x 1.7 meters / Weight approx. 450 kg Subject to errors and omissions. Tsdpfx Aszkv Eusa Ijc

Condition: new, functionality: fully functional, Year of construction: 2026, overall weight: 290 kg, power: 0.37 kW (0.50 HP), input voltage: 400 V, total length: 800 mm, total width: 750 mm, total height: 1,550 mm, feed length X-axis: 220 mm, feed length Y-axis: 220 mm, feed length Z-axis: 200 mm, grinding spindle motor power: 370 W, Special Offer – 5% Discount Available! Slotting Machine Tsdpfxjyux E Ho Aa Ijc The Slotting Machine is a compact and reliable machine designed for precision slotting, keyway cutting, internal profiling and shaping operations. Its rigid construction and adjustable stroke make it an ideal solution for tool rooms, maintenance workshops and metalworking facilities. The machine features a rotating head with a 90° swivel, allowing greater flexibility when machining complex workpieces. With six selectable stroke speeds and a maximum stroke length of 125 mm, it delivers accurate and efficient machining for a wide range of applications. The robust construction ensures excellent stability and precision while maintaining low operating costs. The machine is suitable for both repair work and small-batch production. Main Features • Heavy-duty construction • Adjustable stroke • Six stroke speed settings • 90° swivelling head • High machining accuracy • Compact design • Easy operation • CE certified Technical Specifications • Maximum stroke: 125 mm • Stroke speed: 60–350 strokes/min • Number of speed steps: 6 • Head rotation: 90° • Table size: 500 × 200 mm • Table travel (X/Y): 220 mm • Z-axis travel: 200 mm • Motor power: 0.37 kW • Tool shank diameter: Ø10 / Ø16 mm • Machine dimensions: 800 × 750 × 1550 mm • Machine weight: 290 kg Applications • Slotting • Keyway machining • Internal profiling • Shaping operations • Tool rooms • Maintenance workshops • Metalworking • Small-batch production Transport and Delivery The machine is supplied brand new and includes a 12-month warranty, warranty service and professional after-sales support. We provide professional transport throughout Europe using specialized machinery logistics. Every machine is securely loaded, protected during transport and delivered directly to the customer's premises. We also assist with export documentation and international shipping arrangements. Worldwide shipping is available upon request. About Metal Technics Polska Metal Technics Polska is a manufacturer and distributor of professional metalworking machinery. We supply high-quality machines throughout Europe and provide expert technical advice, spare parts and comprehensive after-sales support. Contact us today for pricing, delivery times, machine availability, additional photos, videos or a personalized quotation.

Condition: new, functionality: fully functional, Year of construction: 2026, overall weight: 2,200 kg, power: 3.7 kW (5.03 HP), input voltage: 400 V, input current: 7 A, input frequency: 50 Hz, broaching length: 200 mm, number of broaching positions: 4, broaching speed: 25 m/min, workpiece diameter (max.): 460 mm, total length: 1,717 mm, total width: 1,221 mm, total height: 1,885 mm, Special Offer – 5% Discount Available! Metal Slotting Machine B5020 – 200 mm Stroke The Metal Technics Polska B5020 Metal Slotting Machine is a professional industrial machine designed for machining keyways, splines, internal grooves and other precision slotting operations. Its rigid construction, large rotary table and automatic feeds ensure excellent machining accuracy, high productivity and reliable operation. The machine is ideal for tool rooms, maintenance departments and manufacturing facilities. With a maximum slotting force of 5 kN, a 200 mm ram stroke and a 360° rotary table, it is suitable for a wide range of precision machining applications. Main Features Todpszf Huiofx Aa Ioc • 200 mm ram stroke • Heavy-duty industrial construction • Ø460 mm rotary table • Automatic longitudinal, cross and rotary feeds • Adjustable ram inclination • Maximum slotting force: 5 kN • High machining precision • CE certified Technical Specifications • Model: B5020 • Maximum ram stroke: 200 mm • Stroke speeds: 32 / 50 / 80 / 125 strokes/min • Ram inclination: 0°–8° • Vertical ram adjustment: 200 mm • Table diameter: 460 mm • Maximum table load: 400 kg • Longitudinal table travel: 420 mm • Cross table travel: 420 mm • Table rotation: 360° • Maximum tool size: 25 × 40 mm • Maximum slotting force: 5 kN • Main motor power: 3 kW • Feed motor power: 0.7 kW • Machine dimensions: 1717 × 1221 × 1885 mm • Machine weight: 2200 kg Applications • Keyway machining • Internal splines • Internal grooves • Slotting operations • Tool rooms • Maintenance workshops • Metalworking • Industrial manufacturing Transport and Delivery The machine is supplied brand new and includes a 12-month warranty, CE Declaration of Conformity, technical documentation, warranty and professional after-sales support. Spare parts are readily available. We provide professional transport throughout Europe using specialized machinery logistics. Every machine is securely loaded, protected during transport and delivered directly to the customer's premises. We also assist with export documentation and international shipping arrangements. Worldwide shipping is available upon request. About Metal Technics Polska Metal Technics Polska is a manufacturer and distributor of professional metalworking machinery. We supply high-quality machines throughout Europe and provide expert technical advice, spare parts and comprehensive after-sales support. Contact us today for pricing, delivery times, machine availability, additional photos, videos or a personalized quotation.

Condition: used, Manufacturer: Konkoly Electro Kft., Hungary Year of manufacture: 2020 Year of installation: 2020.12 Rated voltage: 400 V Maximum current consumption: 40 A Tedpfx Aozumw Noa Isc Frequency: 50 Hz Required pressure: 6 bar Total weight: 5500 kg Noise level: < 95 dB Hydraulic pressure: Cycle time: approx. 30 sec. Changeover time: approx. 10-30 min., depending on the required tooling.

Condition: excellent (used), Broaching tool, broaching needle, special tool, grooving tool, keyseating machine, keyway broaching machine, keyway broaching machine, keyway broaching tool, broaching needle -Manufacturer: SWZ, broach push broach -Type: B 6 J9x1.8 RL 24-72mm -Item no.: 45 0014 -Width: 6mm -Number: 1x broach available -Price per piece Todpfxeitt Rye Aa Ioc -Total dimensions: 900/6/H13 mm -Weight: 0.5 kg/pc.

Condition: ready for operation (used), functionality: fully functional, Hoyton GH-500 slotting and mortising machine, maximum slot length 500mm, maximum slot width 50mm, cutting speed 7.5 mpm, return speed 15 mpm, 3 hp. The machine is in good condition and includes a cabinet or workbench filled with accessories. This workbench is 2 meters long x 1 meter wide x 93 cm high and has a vise and a dividing head. Tjdpfezmp H Rex Aa Ijc