Used Benford Hd 1000 for sale (10,104)

Condition: excellent (used), Year of construction: 2013, Vernet HD-X 618 / HBP 410/723 G CNC Drilling / Sawing Line – Year 2013. 3 Spindle Drill. 16.5 metres In-Feed. 14 metres Out-Feed. Pusher Unit Feed. Milling / Slotting. Solid Carbide Tooling. Small parts conveyor. Ledpsx Rut Tjfx Al Ijhh 4 way Scribing. In-Feed Cross Transfers. Out-Feed Cross Transfers.

Condition: excellent (used), Year of construction: 2019, HD-SFVO 412-S HBE 320/523 G- YEAR 2019. Marking-drilling-milling-shearing & sawing line HD-SFVO 412-S DRILLING CAPACITY. Flat bars: 50x10 to 400x30 Angles: 50x50x5 to 250x250x20 IPN-IPE: 80 to 400 HEA-HEB: 100 to 400 UPN-UPE: 80 to 400 Square and rectangular tubes: 50x50 to 300x300x20 HBE 320/523 G SAWING MACHINE. Ledpfey R Tk Rsx Al Iehh Effective cross-section (mm): 90°: 400x300 Bevel cut, left pivot (W x H, mm): 75°: 400x300 60°: 400x300 45°: 330x300 30°: 200x300 Bevel cut, right pivot (W x H, mm): 75°: 400x300 60°: 400x300 45°: 310x300 Power supply: • Three-phase 400V ± 15 V + ground, 50Hz • Installed power: 40 kVA Compressed air: • Minimum pressure: 6 bar • Maximum flow rate: 3 Nm³/h Operating temperatures: • From 10°C to 40°C Milling unit specially designed for machining small square or rectangular tubes (slotted holes, shaped cuts, etc.). With the engraving equipment: ability to engrave letters or numbers for part identification. Allows, among other things, marking of tubes with sufficient depth to ensure legibility after painting or galvanizing Secure holding of the bar during milling: the bar is clamped in the movable vice system to ensure proper machining while minimizing vibrations. Improved positional tolerance of one hole relative to another within a group of holes (within a maximum length of 150 mm) Additional features Cycle for centre punching, countersinking, tapping, deburring, and chip breaking Automatic measurement of tool length (HSS) Side and centre tool cooling 230-ton shear Feature Mobile hydraulic shear Straight cut Average cutting time: approximately 2 to 2.5 seconds Capacities: HEB 140 IPE 300 IPN 280 Angle bars 150x150x18 L 200x100x14 UPE 300 UPN/UPAF 300 Flat bars 300x20

Condition: excellent (used), Year of construction: 2021, Traverses X Y Z: 660 x 450 x 500mm, Table size 720mm x 420mm, table load 500kgs, spindle speed 12,000rpm, Ledpfx Aljzbitue Iehh spindle motor power 28Hp, Siemens 828D Control with Shopmill, rapid feed XYZ axis 24m/min, Spindle taper BT40, 12 station ATC

Condition: excellent (used), Year of construction: 2017, operating hours: 8,919 h, functionality: fully functional, REF: MM6307 1 x Rondo Compas HD Series pastry sheeter with touch-screen control panel and automatic flour duster. This pastry sheeter is capable of storing up to 100 different product programs to produce various different pastries. Model - SFA6127H. Serial number - D7603879. Date of manufacture - 2017. Useable width - 600mm. Table length overall - 3500mm. Ledexvzqtepfx Al Ishh Electrical requirements - 420 V / 50 hz / 3 phase. Power - 1.4 kW / 2.7 Amps. Overall dimensions (with dough catch pans extended) - 3820mm long x 1260mm wide x 1530mm high. Total machine weight - 420 kg. Condition - Excellent, ex-bakery condition.

Condition: used, Year of construction: 2021, functionality: fully functional, Kornit Storm HD6 Translating industry challenges into opportunities is where game-changing technology is emerging. Kornit Storm, the robust and field-proven commercial DTG printer serving small to mid-size printing businesses, is now available as an HD technology platform. Unique configuration of CMYKRG (+ White) enables limitless design colours and customisation DescriptionSpecifications Print Heads HD6: 20 heads; Max Printing Solution Up to 1,200 dpi Ink Channels HD6: 6 colours CMYKRG + White; INK RECIRCULATION SYSTEM Integrated NEOPIGMENTTM INK CONTAINERS Bulk ink system supporting 4 litre ink containers MAX PRODUCTION OUTPUT Dark Garments: 55, Light Garments: Dark + 25% PRINTING AREA Up to 20 x 28 in/50 x 70 cm PRINTABLE SUBSTRATES Cotton, Polyester, Cotton- Polyester Blends, Lycra, Viscose, Silk, Leather, Denim, Linen, Wool and more HUMIDITY SYSTEM Integrated BACKUP BATTERY SYSTEM Integrated MAX WEIGHT Approx. 1705 kg / 3759 lb POWER REQUIREMENTS 400/208 VAC, 50/60 Hz, 3 ph, 3W+N+PE COMPRESSED AIR PRESSURE 6 – 8 bar (90 – 116 psi) regulated OPERATING SYSTEM Windows 7 OPERATING CONDITIONS 18°C-30°C / 64.4°F-86°F, Humidity: 45%-95% DIMENSIONS 114X80X65 in/ 290x207x165 cm Lhedpozb Nbrjfx Al Ish

Condition: good (used), CORIMPEX BEAM WELDING MACHINE TYPE BWM TC 2000-1000 3-15 machine. WEB : Height 200 -:- 2000mm (flanges included). Thickness 5 -:- 25mm FLANGE : Width 150 -1000mm Thickness 8-40mm Max. post-deforming thickness = 35 mm on 1000 mm flange width Lodpfx Ajzc Rl Uol Ijhh MAX. BEAM WEIGHT : 1000 Kg / metre MIN. BEAM LENGTH : 3000 mm MAX. BEAM LENGTH : 15.000 mm. HYDRAULIC CYLINDER : 1800 mm. TACK-WELDING : Not needed. POWERED ROLLS IN THE : speed = 12 m/min. ENTRY/EXIT CONVEYORS PISTON WORKING : 6/9 Tons. TRAVEL SPEED RANGE : 0,2 -:- 2,1 m/min WELDING PROCESS : submerged Arc Tandem.

Condition: good (used), Year of construction: 2004, functionality: fully functional, PEDDINGHAUS TDK 1000/9 DRILLING MACHINE 9 SPINDLES MAXIMUM PROFILE 1000 X 420mm MEBA 1020 DGP SAWING MACHINE cutting diameter: 510 mm capacity 90 degrees: round: 510 mm capacity 90 degrees: flat: 1020 x 510 mm capacity 60 degrees: round: 500 (400) mm capacity 60 degrees: flat: 500 (400) x 510 mm capacity 45 degrees: round: 510 mm capacity 45 degrees: flat: 750 (670) x 510 mm Lhjdpfx Aezc I Iyjl Ish

Condition: ready for operation (used), * Brand: Svedala Lhodpfxszgf Aus Al Ieh * Model: vibrating chute * Dim: length 5000 mm - width 1000 mm * incl.: steel construction and grizzly bars.

Condition: good (used), Year of construction: 2016, Riggs 1000 Twin head depositor 2016, Stainless frame, twin head depositor, one head fills from 50ml to 600ml and the other from 125ml to 1200ml, on mobile scissor lift table Ljdsy Umxpjpfx Al Iohh

Condition: new, rotational speed (min.): 25 rpm, rotational speed (max.): 1,500 rpm, Distance between centers 1000 mm Max. swing over bed 560 mm Max. swing over carriage 350 mm Max. swing in gap 788 mm spindle bore 105 mm Spindle Taper Camlock D1-8 Lhedpfx Aozdr Rysl Ieh Spindle speed 25 - 1500 1/min Travel cross slide 326 mm Travel top slide 130 mm If you have any questions concerning the machine, please do not hesitate to contact us by phone or e-mail. Feel free to view our other advertisements for a complete overview of our stock.

Condition: new, overall weight: 1,720 kg, total height: 1,700 mm, total width: 1,080 mm, total length: 2,200 mm, Distance between centers 1000 mm Ljdozdr Huepfx Al Iohh Max. swing over bed 460 mm Max. swing over carriage 270 mm Max. swing in gap 690 mm spindle bore 80 mm Spindle Taper Camlock D1-6 Spindle speed 25 - 1700 1/min Travel cross slide 290 mm Travel top slide 120 mm If you have any questions concerning the machine, please do not hesitate to contact us by phone or e-mail. Feel free to view our other advertisements for a complete overview of our stock.

Condition: excellent (used), Weiss Type: WT3-1000/40 Weiss temperature test chamber with S!MCON / 32 control system, water-cooled Control panel: “Touch panel” The “Touch panel” control panel allows all control and operating commands to be executed simply by touching the function symbols. Adjustable feet To compensate for unevenness in the floor and to ensure sufficient ventilation of the machine, the test chamber is equipped with adjustable feet. Feedthroughs The test chamber is equipped with feedthroughs on the right and left sides. These allow measuring cables and testing equipment to be placed in the test chamber. Feedthrough installed as standard R1: 125 mm L1: 50 mm Test chamber volume: approx. 990 liters Test chamber dimensions: height 950 mm, width 1100 mm, depth 950 mm External dimensions: height 2000 mm, width 1415 mm, depth 2105 mm Data for temperature tests: Temperature range: -40 to +180 °C Temperature deviation over time in the center of the usable space: ± 0.1 to ± 0.5 K Temperature deviation spatially: ± 0.5 to ± 1.5 K Temperature change rate: Heating: 4.0 K/min Lsdezgbt Njpfx Al Iehh Cooling: 3.0 K/min Maximum heat compensation: 4500 W Data for operation: Test chamber lighting: halogen bulb 2x 24V, 50W Rated voltage: 3/N / PE AC 400 V ± 10% 50 Hz Rated current: 22.0 A, rated power 11.5 kW Fuse on customer side: 32 A slow-blow Sound pressure level approx. measured at a distance of 1 m from the front, 1 m height: 56 dB(A) Refrigerant: R-404A Weight: 840 kg For your safety as a buyer, please note the following information: The following points are carried out on our offered chambers in advance: 1. Functional check and replacement of necessary components 2. If necessary, refill with legally compliant refrigerant 3. Leak test with certificate 4. After successful inspection, the chambers are subjected to a documented test run. Condition: used Scope of delivery: (See picture) (Changes and errors in the technical data and information are subject to change!) We will gladly answer any further questions you may have by phone.

Condition: good (used), Weiss Type: WK1-1000/70 Weiss Climate Testing Chamber, Water-Cooled (Refrigerant converted to R-452A) Control panel: "Touchpanel" All control and operating commands can be initiated on the "Touchpanel" by simply touching the function symbols. Feedthroughs The test chamber is equipped with feedthroughs on the right and left sides. These allow measuring cables and testing equipment to be placed in the test chamber. Feedthroughs: 1 feedthrough, diameter 125 mm, installed on the right 1 feedthrough, diameter 50 mm, installed on the left Volume: 990 liters Test chamber dimensions: Test chamber: width 1100 mm, depth 950 mm, height 950 mm Housing: width 1385 mm, depth 1850 mm, height 1980 mm Data for temperature tests: Minimum temperature: -70 °C Maximum temperature: +180 °C Temperature deviation, over time: ± 0.1 to ± 0.5 K Lodpfezgbtpox Al Iohh Temperature homogeneity, spatially: ± 0.5 to ± 2 K Temperature change rate, heating: 4 K/min Temperature change rate, cooling: 2.5 K/min Maximum heat compensation: 2750 W Data for climate tests: Temperature range: +10°C to +95°C Humidity range: 10 to 98% RH Temperature deviation, over time: ± 0.1 to ± 0.3 K Temperature homogeneity, spatially: ± 0.5 to ± 1 K Humidity deviation, over time: ± 1 to ± 3% RH Data for operation: Rated voltage: 3/N/PE AC 400V ±10% 50Hz Rated current: 29A, rated power: 19.8 kW Refrigerant: R-452A / R23 Weight: approx. 910 kg For your security as a buyer, please note the following information: The following points are carried out on our offered chambers in advance: 1. Functional check and replacement of any necessary components 2. If necessary, new filling with legally compliant refrigerant 3. Leak test with certificate 4. After successful inspection, the chambers are subjected to a documented test run. Condition: used Scope of delivery: (See image) (Changes and errors in the technical data are subject to change!) We will gladly answer any further questions you may have by telephone.

Condition: defective spare-parts repository (used), Vickers Type: HVS 1000 The digital micro-Vickers hardness tester HVS 1000 features a unique and precise design in the areas of mechanics, optics, and light source, and is capable of producing a clearer image of the impression, thus enabling more accurate measurements. Main purpose and scope of application: 1. Iron and steel, non-ferrous metals, metal foils, hard alloys, sheet metal, microstructures 2. Carburized, nitrided, and decarburized layers, surface hardening layers, plating, coatings 3. Glass, wafers, ceramic materials Specifications: Model HVS1000 Type Digital Micro Hardness Tester Test forces (N) 0.098 / 0.246 / 0.49 / 0.98 / 1.96 / 2.94 / 4.90 / 9.80 Test forces (Kgf) 10 / 25 / 50 / 100 / 200 / 300 / 500 / 1000 Load control Automatic loading and unloading Objective-indenter turret Manual Dwell time (s) 0~60 Microscope magnification x 400x for measurement, objective 40x, eyepiece 10x 100x for observation, objective 10x, eyepiece 10x Micrometer resolution (μm) 0.01 Test range 5 HV~3000 HV Dimensions of XY test table 100X100 mm Travel range of XY test table 25X25 mm Max. sample height 120mm Max. sample width 110mm Hardness conversion HK, HRA, HRB, HRC, HRD, HR15N, HR30N, HR45N, R15T, HR30T, HR45T, HV, HBW Output Built-in printer, RS232 interface Power 220V, 60/50Hz Dimensions (mm) 441 x 270 x 480 Net weight / kg) 35 Condition: used Scope of delivery: (See picture) (Subject to changes and errors in technical data and information!) Lhodpfx Aozgbr Ssl Ieh We will be happy to answer any further questions you may have by phone.

Condition: good (used), CTS Type: TSR-30/1000 Water-cooled Lodpfxezgbnto Al Ishh The type designation of the CTS cabinet series is structured as follows: e.g., Type TSR-30/1000 1) T means: Temperature 2) S means: Stress Screening 3) R means: External Conditioning 4) -30 means: Lower temperature -30 °C 5) 1000 means: 1000 liters test chamber volume Technical performance data: A) TSR-30/1000 base unit without hose connections, i.e., for use as a stand-alone temperature test chamber Temperature tests: Temperature range -40°C to +180°C Final temperature -45°C Temperature deviation ≤ ±0.3 K over time Temperature change rate according to IEC 60068-3-5 Heating 6.0 K/min Cooling 5.0 K/min Heat radiation approx. 5000 W at +20°C approx. 4200 W at ±0°C approx. 3000 W at -20°C The technical data refer to an ambient temperature of +25 °C, rated voltage 400V, without test specimen, without radiation, and without additional equipment. Air volume flow rate approx. 2000 m³/h B) TSR-30/1000 base unit with hose connections, for connection to an on-site external test chamber Temperature tests: Temperature range -30°C to +170°C Temperature deviation ≤ ±0.1 to 0.5 K over time Average temperature change rate, measured with the circuit short-circuited Heating 4.0 K/min Cooling 4.0 K/min in the range of +150°C to -10°C The technical data refer to an ambient temperature of +25 °C, rated voltage 400V, without test specimen, without radiation, and without additional equipment, measured with the circuit short-circuited Caution: The on-site external test chamber must be absolutely sealed and appropriately insulated; any penetrations must be optimally sealed on-site. Dimensions: Test volume 1000 liters Air circulation connection Ø 200 mm Test chamber dimensions height 900 mm width 1000 mm depth 1100 mm External dimensions height 1950 mm width 1270 mm depth 2245 mm Technical design: Refrigeration unit: water-cooled, low-noise, hermetically sealed stepless power adjustment by electronic monitoring and control system, environmentally friendly refrigerant R404A Door: fully opening door, door stop on the left, one-hand operation, lockable. Insert grid: stainless steel, support area 970 x 980mm Load per grid max. 35 kg Total load with max. grid capacity 100 kg Test chamber lighting: Halogen lamp 20 W, 12 V Control: - 32-bit controller - LCD control panel Operating data: Electrical connection 400 V +6/-10 %, 3/N, 50 Hz Rated power 13.3 kW Protection class IP 22 Sound pressure level < 60 dB(A) Weight approx. 850 kg For your safety as a buyer, please note the following information: The following points are carried out on our offered chambers in advance: 1. Functional check and replacement of necessary components 2. If necessary, new filling with legally compliant refrigerant 3. Leak test with certificate 4. After successful inspection, the chambers are subjected to a documented test run. Condition: used Scope of delivery: (See picture) (Changes and errors in the technical data are subject to change!) We will be happy to answer any further questions you may have by phone.

Condition: used, Year of construction: 1978, x-travel 1.000 mm y-travel 340 mm z-travel 450 mm table: 1.300 x 400 mm spindle taper ISO 40 SK turning speeds 32 - 1.400 U/min Lsdpozf Nrdefx Al Ishh spindle stroke 80 mm total power requirement 7,5 kW Features: - Universal console milling machine with HEIDENHAIN digital display - Mechanical tool clamping - Cooling system - Various SK 40 tool holders - Machine documentation in German

Year of construction: 2026, condition: new, working width 1000 mm workpiece width - max. 0,5 - 50 mm sandingbelt width -- mm weight of the machine ca. 2,5 t With the SBM-L 1000 G1S2, which works in the dry process, in alternating operation Steel, stainless steel and aluminum can be machined. She deburrs and rounds the edges on the outer and inner contours of punched, laser, fine plasma or water jet cut workpieces with a thickness of up to 50 mm on both sides in just one operation. * Two sanding units, 1 each on the top and bottom, remove spatter and slight burrs on outside and inside edges of sheet metal. * A total of four sanding belts, 2 each on the top and bottom Underside, process the sheets on both sides at the same time. here All edges are softened or rounded, depending on the tool settings. * Machining on both sides saves time-consuming turning of the workpieces and Lhsdpfouia Dqsx Al Ieh edit twice. * All pairs of aggregates can be switched on/off separately depending on the application as well as to be set. * Including Siemens S7 control: - Easy and comfortable operation through intuitive user interface - High operating security through 3 password-protected user levels - Integrated program memory - USB / RJ 45 interface for data exchange or connection of external Components (e.g. barcode scanner) - Direct entry of material thickness via touch panel - All axes automatically adjust to preselected material thickness - Standby position for deactivated aggregates - Service-friendly (e.g. plain text error messages) consisting of: - Grinding machine SBM-L 1000 G1S2 (kit) - 4x sanding belts SBM 1000 with bar P60 SiC - Sanding belt SBM-L 1000 L=3125 B=70 P80 Cubitron 2 784F - SBM-L tool wear compensation Siemens S7 - DDE 3002 dry suction - Standard piping DDE 3002 / WDE 3002 for SMD 123, SMD 133 Further detailed technical data on request. The machine is in stock Niederlangen available immediately.

Condition: good (used), Year of construction: 2012, Used 3-meter CNC press brake from Amada Lhedpfx Alozd S A Ne Ioh Type: HD 1003 NT Capacity: 3100 x 100 tons Year of manufacture: 2012 Servo-hydraulically controlled AMNC control system X1, X2, R, Z1, and Z2 CNC controlled Akas Fiesller laser safety system

Condition: excellent (used), Weiss Temperature Chamber Here we offer a Weiss temperature chamber. Weiss temperature chamber, air-cooled, with Weiss condenser cooler Test chamber volume approx. 990 liters Data for temperature tests: Temperature range -40°C to +180°C Temporal temperature deviation in the center of the usable space ± 0.1 to ± 0.5 K Spatial temperature deviation ± 0.5 to ± 2.0 K Temperature gradient (according to IEC 60068-3-5) 1 to 4 K Temperature change rate (according to IEC 60068-3-5) Heating 4 K/min Cooling 3 K/min Heat compensation max. 4500 W Feedthrough, installed as standard R1: NW 125 mm L1: NW 50 m Dimensions: Test chamber dimensions: Width 1100 mm x Depth 950 mm x Height 950 mm Housing dimensions: Width 1390 mm x Depth 1525 mm x Height 1995 mm Maximum load (evenly distributed over the area) of the test chamber floor 150 kg Per insert shelf 50 kg Ljdezfzamspfx Al Ijhh Total load of the shelf supports 100 kg Data for operation: Test chamber lighting: Halogen bulb 24V, 50W Rated voltage 3/N / PE AC 400 V ± 10% 50 Hz Rated power 11.5 kW Rated current 22 A Heat dissipation water-cooled test cabinets max. heat dissipation to the environment 1.3 kW Noise measurement: Sound pressure level approx. 64 dB(A) Refrigerant: (converted to R-452a) Weight: approx. 840 kg Type: WT11-1000/40 For your safety as a buyer, please note the following information: The following points are carried out on our offered chambers in advance: 1. Functional check and replacement of necessary components 2. New filling with legally compliant refrigerant 3. Leak test with certificate 4. After successful inspection, the chambers are subjected to a test run, which is monitored with calibrated devices. Condition: used Scope of delivery: (See picture) (Changes and errors in the technical data and information are subject to change!) We will be happy to answer any further questions you may have on the phone.

Condition: excellent (used), Weiss Temperature Chamber We offer a Weiss temperature chamber here. Lhedszfy Rwjpfx Al Ieh Weiss temperature chamber, air-cooled with Weiss condenser cooler Test chamber volume approx. 990 liters Data for temperature tests: Temperature range -70°C to +180°C Temporal temperature deviation in the center of the useful space ± 0.1 to ± 0.5 K Spatial temperature deviation ± 0.5 to ± 2.0 K Temperature gradient (according to IEC 60068-3-5) 1 to 4 K Temperature change rate (according to IEC 60068-3-5) Heating 5 K/min Cooling 5 K/min Heat compensation max. 2750 W Feedthrough integrated in the standard configuration R1: NW 125 mm L1: NW 50 m Dimensions: Test chamber dimensions: Width 1100 mm x Depth 950 mm x Height 950 mm Housing dimensions: Width 1390 mm x Depth 1525 mm x Height 1995 mm Maximum load (evenly distributed over the area) of the test chamber floor 150 kg per insert shelf 50 kg Total load of the shelf supports 100 kg Data for operation: Test chamber lighting Halogen bulb 24V, 50W Rated voltage 3/N / PE AC 400 V ± 10% 50 Hz Rated power 27.0 kW Rated current 42.02 A Heat dissipation of water-cooled test cabinets max. heat dissipation to the environment 1.3 kW Noise measurement: Sound pressure level approx. 64 dB(A) Refrigerant: (converted to R-452a) Weight: approx. 960 kg Type: WT11-1000/70/5 For your security as a buyer, please note the following information! The following points are carried out on our offered chambers in advance: 1. Functional check and replacement of necessary components 2. New filling with legally compliant refrigerant 3. Leak test with certificate 4. After successful inspection, the chambers are subjected to a test run, which is monitored with calibrated devices. Condition: used Scope of delivery: (See picture) (Changes and errors in the technical data are subject to change!) We will gladly answer any further questions you may have on the telephone.

Condition: used, all stainless steel 3 tiers Lhodpfxozc I H Nj Al Ijh nett belt length ± 5.800 mm nett belt width ± 940 mm stainless steel mesh wire belt outside dimensions (l x w x h) : ± 7.200 x 1.400 x 2.900 mm + Evaporator "Goedhart B.V." Type LLK.s 411m² manufacturing number: PJV100282 Year of manufacture: 2010 Capacity: 135 dm³ Refrigerant: NH3 Weight: 770 kg, Working pressure: 22 bar Test pressure: 32 bar Overall dimensions including cooling panels and stainless steel door: 7.500 x 2.700 x 3.300 mm

Condition: ready for operation (used), Year of construction: 2010, operating hours: 5,002 h, functionality: fully functional, machine/vehicle number: NT100JG0126, turning length: 424 mm, turning diameter: 370 mm, travel distance X-axis: 380 mm, bar passage: 52 mm, controller model: FANUC FS-31iA5 (MAPPS 4), TECHNICAL DETAILS Turning length: 424 mm Maximum turning diameter: 370 mm (270 mm with turret 2) Bar capacity: 52 mm Turning-milling spindle Full indexing capabilities: Yes X-axis travel: 380 mm Y-axis travel: ± 105 mm Z-axis travel: 460 + 155 mm (ATC) B-axis: ± 120º Spindle speed: 12,000 rpm Drive power: 9/5.5 kW Tool magazine Number of magazine positions: 38 Tool holder: Capto C5 Maximum tool length: 250 mm (210 mm for tools under Ø70 mm) Maximum tool diameter: 70 mm / Ø130 mm (with/without adjacent tools) Maximum tool weight: 5 kg Lower turret X-axis travel: 155 mm Z-axis travel: 610 mm Number of tool slots: 10 Tool speed: 6,000 rpm Drive power for driven tools: 1.5/1.2 kW Main spindle Spindle speed: 6,000 rpm Drive power: 11/7.5 kW Spindle bore: 73 mm Chuck type: Hollow chuck (8") Manufacturer: KITAGAWA Spindle nose: JIS A2-5 Maximum torque: 223 Nm Counter spindle Spindle speed: 1,000 rpm B-axis: 4 fixed positions, 0º, -30º, -180º (-225º for overhang onto conveyor, if available) MACHINE DETAILS Control: FANUC FS-31iA5 (MAPPS 4) Potential rated power: 39.24 kVA Dimensions & Weight Dimensions (L x W x H): 2,705 x 2,425 x 2,385 mm Weight: 8,800 kg Operating Hours Lsdpfx Alezf H Ezj Ishh Power on: 54,061 h Spindle 1 operating hours: 9,813 h Spindle 2 operating hours: 5,002 h EQUIPMENT Chip conveyor Signal lamp High-pressure pump Air blow nozzle outside the spindle Foot switch (dual) for main and counter spindle

Year of construction: 2026, condition: new, functionality: fully functional, Equipment: CE marking, documentation/manual, Ease up your production with a Wattsan CW cleaning machine, continuous and with water-cooling. It can remove rust, paintwork, oil products, oxide coatings, welding scales, and carbon deposits from a variety of metals. This model features 1 type of cleaning seam. There are no consumables and no need for a significant amount of necessary space. Compact, portable laser cleaner that can work at any angle and in the most inaccessible places. The chiller is also built-in. The fiber length is 8 meters. The laser gun is lightweight and comfortable for long-term use. Ledpfeiicgkjx Al Iehh You can give our managers a call for additional details! Wattsan CW Cleaning machine characteristics: Cooling: water Laser power: 1000-3000 W Machine size: 880*560*1010 mm Laser source: JPT / Raycus Weight: 145 kg Virmer provides not only prime machines but also service and delivery. Our engineers and managers are ready to answer all of your questions and provide video assistance if required. Also, owners of Wattsan equipment get lifetime online support. Virmer is located in the Netherlands and works all over Europe. Virmer is Wattsan's official supplier. We provide not only laser engravers, but also metal cutters, welders, markers and cleaning machines. Wattsan is a Chinese manufacturer, which has been creating laser equipment for almost 15 years and keeps evolving with the help of its clients. Thanks to feedback Wattsan made over 50 modernizations, which made machines more reliable, precise and powerful so you could upgrade your business up to the new level. YOU CAN WRITE OR CALL US! WE WILL SELECT THE RIGHT MACHINE FOR YOUR TASK On our company you can find a wide range of machines and components: Laser Metal Cutting Machine; Laser Metal Machine, Fiber Metal Laser, Fiber Metal Laser Engraver; CNC laser machine for metal; Laser machine for wood; CNC laser machine; Laser engraving machine; Laser engraver; Laser cutting machine for plywood; Laser engraver; Laser cutting machine for metal; CNC milling machine; laser marker. Lenses; Chillers; Cooling system for machine; Chiller S&A ; IPG laser, MAX photonics, Raycus; Compressor; Rotary device; Mirror for laser machine.

Condition: good (used), Ultrasonic sensor, ultrasonic sensor, ultrasonic generator, ultrasonic generator Manufacturer: MS, Ultrasonic welding generator -Type: SoniGEN 35/1000 or similar, unfortunately no exact designation -Power output: kVA Lodpfsxxkbaex Al Ishh -Dimensions: 460/150/H150 mm -Weight: 5.5 kg

Condition: good (used), Year of construction: 1971, Container rotator, boiler rotator, welding rotator, welding rotator, welding device, welding turntable, welding rotator Lsdpfozgalqex Al Ijhh -Manufacturer: Walter Gieseking, Container rotating device, Welding rotating device type SG1 -Load capacity: 1200 kg -Roller spacing: 187 - 1000 mm -Rollers: Ø 175 x 50 mm -Rolling speed: 0.2 to 0.85 m/min Right/Left rotation -Control unit: with manual control, speed control via handwheel -Individual components: see photos -Transport dimensions: 1610/570/H330 mm / 1250/300/H330 mm -Total weight: 217 kg