Used Banding Machine for sale (65,234)

Condition: used, Year of construction: 2013, Used machine Year of manufacture: 2013 Equipment/features: - Machine table with 13 running rollers for improved workpiece guidance - Edge feed, synchronized with the belt feed - Edge thickness adjustable via digital counter - Pneumatic roller separation with cutter (for cuttable edges) - Three pressure rollers - Belt feed motor 0.25 kW; approx. 1250 mm length; feed rate approx. 6.0 m/min; 50 mm wide timing belt with thick, workpiece-friendly rubber coating. Digital counter for height adjustment - Direct glue application to the workpiece: leakproof glue pot with glue supply from below and fast heat-up time after machine stoppage - Flush trimming unit for front and rear workpiece edges, automatic sensing at the workpiece, pneumatic trimming with a cutter for cuttable edges - Flush milling unit with vertical sensing and horizontal guidance, reproducible adjustment via digital counters, 2 high-performance 0.4 kW high-frequency motors, continuously adjustable from 4000 to 18000 rpm, cutter diameter 70 mm, Z4, radius 2 mm/15°; central extraction connection Ø 100 mm, 2 chip extraction hoods with hose Ø 60 mm - Automatic height adjustment of the upper cutter with the belt feed - Continuous workpiece support approx. 1800 mm long, workpiece support rail extendable by approx. 300 mm - Rotatable film disc Ø 800 mm Technical details: - Minimum workpiece width: approx. 80 mm - Workpiece thickness: 10 – 50 mm - Minimum workpiece length: approx. 220 mm - Edge thickness: 0.4 – 2.0 mm - Roller separation max.: 1.0 x 55 mm, 2 x 45 mm Hedpfx Acsytkiuevsk - Glue pot heating power: 2.7 kW - Electrical connection: 400V, 50 Hz, 3Ph + N - Total connected load: 3.8 kW - Heat-up time: approx. 10 minutes - Pneumatic connection: 6 bar - Working height: approx. 880 mm - Dimensions: approx. 1800 x 700 x 1300 mm (without film disc Ø 800) - Net weight: approx. 260 kg Availability: short-term Location: Flörsheim

Condition: new, Year of construction: 2026, Manual band saw machine for cuts from 0° to 60° right. Hedpfx Aogculvscvek Hydraulic belt tension, loop handle with control button. Combination belt guide with lateral bearings. Carbide cutting tips and an upper bearing. Manual pruning or pruning option without the user, with the weight of the bracket and controlled by hydraulic brakes; then the bracket is raised again manually to the desired position. Manual clamp for quick and precise blocking of the part. Rotation of the bracket from 0° to 60° to the right with locks, precise measurement of the angle, manual vice with quick-release lever. Millimetric degree scale rod. Coolant tank integrated on the upper side of the base frame with a discharge nozzle and electric coolant pump for cooling on both sides of the saw blade guides. Control voltage 24 VAC, main switch and control. Maximum current protection and short circuit. Connection voltage: 400V/50Hz/3Ph standard. Machine colour: yellow RAL 1018 and gray RAL 7036. It is always possible for you to inspect the desired system in our production/demonstration hall. Please do not hesitate to contact us.

Condition: excellent (used), Universal DOUBLE-SIDE SIZING & EDGE BANDING MACHINE (for both 1st and 2nd pass) Edges (tape) thickness in rolls (min/max) mm 0,3 - 3 Panels thickness (min/max) mm 10 - 60 Working width (min/max) mm 240 - 2700 Numerical Control /Software SINITRA Adjustable feeding speed (m/min ) 10 - 40 Distance (center-axes) of the Disappearing Dogs (mm) 500 SIZING PART (for each side): Anti-chipping Milling Unit AS 10 (1 x Kw 5,2 ca.) N°2 Hogging Units (1 Top + 1 Bottom) DT 10 (2 x Kw 5,8 ca.)+ Spraying unit (Anti-sticking liquid) EDGE-BANDING PART (for each side): Glueing Unit (Hot Melt + Quick Melt Unit) SP30 (High Melt + Edge control EC40) Hsdpfx Acsywk Eljvok Band Pressure zone (N.C. adjustment) . Edge coils supporting unit (No. 6 reels) Snipping (end-cutting) unit IT 90-S (2 x Kw 0,3 ca.) 28 m/min (0° - 25°) Rough Trimming unit RS 10 (2 x Kw 0,75) Fine Trimming unit (Multi-profile, by N.C.) RF 30 (2 x Kw 0,37) 0°-25° Multi Function Unit (Profile contour Trimming unit) AR 30 (Kw 0,35 x 2) LEFT: 2 x Milling grooving units FB 32 (2 x Kw 5 ca.) 0° - 90° RIGHT: Milling grooving unit FB 30 (1 x Kw 5 ca.) 0° - 90° Profile Scraping unit RB 10 Glue scraping unit RC 10 + Spraying Unit (for polishing liquid) Buffing unit SZ 30 (2 x Kw 0,37) + Hot Air Heater (to reactivate the color of plastic tape) PH 10 OPTION: D.O.M. Unloader with load-bearing column and mobile arm (with vacuum suction cups), for unloading and stacking edged panels

Condition: good (used), Year of construction: 1997, functionality: fully functional, - PVC Primus, 3 mm PVC cartridge system - Gluing, flush trimming, flush milling, chamfer milling, radius milling - Scraper blade, buffing unit - Dimensions: 4700 x 1400 x 1650 mm - Weight: 1300 kg - Working dimensions: Length: 4500 mm Depth: 1020 mm Height: 1630 mm - Connection nozzle: 140 mm Ø - Workpiece width: min. 60 mm - Feed rate: 11 m/min - 6 bar - 400 Volt compressed air - Edge thickness: 8 mm for strip material, 2 mm for roll material - WITHOUT pre-milling unit - New pneumatic cylinder Shipping possible at additional cost Hodswv Uq Ajpfx Acvjk

Condition: good (used), Year of construction: 1998, 0.4-5 mm Workingpiece thickness from to 10-50 mm Total length 2730 mm Weight 720 kg Hjdpfx Aex Tu Rdocvjk

Condition: used, Year of construction: 1995, machine/vehicle number: 795101, Offer 26032 Hydraulic Twin-Column Guided Mitre Band Saw Automatic Machine Technical Data: - Cutting capacity at 90° – round: 310 mm - flat: 520 x 310 mm - Mitre adjustment to the left up to 30° - Cutting capacity up to 45° – round: 340 mm - flat: 350 x 310 mm - Cutting capacity up to 30° – flat: 230 x 310 mm - Saw blade dimensions approx. 5000 x 41 x 1.3 mm - Cutting speed: 17 – 120 m/min Hedpoyv D Idefx Acvjk - Infinitely variable cutting pressure: 0 – 10 m/min - Automatic material feed - Total drive power approx. 400 V / 6.0 kW - Micro-spray coolant system - 2 x roller conveyors, each 2000 mm - Space requirement approx. W 3500 x H 1800 x D 1600 mm - Weight approx. 2000 kg

Condition: new, Year of construction: 2026, The stationary mitre band saw machine for universal use Design: - Solid saw frame made of die-cast aluminium - Saw frame can be swivelled over the material - Robust vice - Large cutting range Hodpog Hy Shefx Acvsk - Two cutting speeds - Saw blade guides made of hard metal with ball bearings - Electric coolant system Technical data: - Mitres from 0° to 60° right hand - motor power 2000 W/1-Ph. 230 V - infinitely variable belt speed from 35 - 80 m/min. - machine weight 140 kg - saw band dimension 2140 x 20 x 0,9 mm cutting ranges: 0° = Ø 175 or 200 x 75/190 x 135 /175 x175 mm 45°= Ø 110 / 150 x110 / 110 x 110 mm 60°= Ø 75 / 100 x 70 / 75 x 75 mm

Condition: excellent (used), Year of construction: 2018, functionality: fully functional, Edgebanding Machine Tempora F 60.06 - Year of manufacture: 2018 - Interchangeable glue pot - Units for pre-milling, end trimming, flush cutting, milling, radius scraping knives, flat scraping knives, buffing - Includes separation agent and cleaning agent application - Spray unit - Edge thickness: 0.4–6 mm - Installation length: 3220 mm Hjdpfx Acex Ha I Usvsk - Saw trimming

Condition: new, Edgebanding Machine HOLZ-HER 1308 XL AURIGA POWER -Showroom machine- Innovation: GLUJET GJ725 This offer concerns an equipment package. The following components and options are already included in the price: - Extendable workpiece support - Edge Control PPC 322 W control system - ECO MODE energy-saving mode - Jointing cutting unit FG201 with 2 milling heads - Diamond milling cutter Ø 70 x 64 x 30 mm, Z2+2, left-hand rotation - Diamond milling cutter Ø 70 x 64 x 30 mm, Z2+2, right-hand rotation Hodpfx Aeu R Sy Aocvek - Edge feed 1903 - Glue application system Glu Jet GJ725 NC PUR PRO - Pressure unit 1912-3 pneumatic - End trimming unit 1918 pneumatic 60 mm - Multifunctional milling unit FR301 MOT6 - Diamond milling cutter Ø 56/60 mm, left-hand rotation - Diamond milling cutter Ø 56/60 mm, right-hand rotation - Corner rounding unit FF301 MOT1 - Scraper unit ZK301 MOT4 incl. high-gloss package - Carbide reversible knives for scraper carrier - Chip collection box for scraper unit - Buffing unit 1940 - Spray device TR301 for infeed and outfeed areas - Motorized pressure bridge adjustment - iTronic-adaptive pressure and glue quantity control - Extended infeed fence 1,252 mm - Motorized adjustment for infeed fence - Pressure unit DW301 with motorized NC axis - Extraction hoods for end trimming unit 1918 - Shelving program - Surface scraper FK701 - Spray device GM301 after the pressure unit - new showroom machine -

Condition: used, Year of construction: 1989, Used machine Year of manufacture: 1989 Condition: Function tested Hjdpfx Aew I U E Ajcvjk Equipment and technical data: Max. edge thickness: 20 mm Max. edge height: 51 mm Max. thickness of coil material: 3 mm Min. workpiece length: 140 mm Min. workpiece width: 60 mm Glue system: 1906 cartridge Pressure unit Milling unit 1920 for flush milling up to 20 mm and chamfer milling Required space (LxWxH): 3150x1800x1375 mm Weight approx.: 800 kg Location: Flörsheim Availability: Short-term

Condition: used, Year of construction: 2009, Used machine Year of manufacture: 2009 Single-sided automatic edge banding machine with CNC control, 10" touch screen Industrial conveyor chain 1 1/4" Joint milling unit FI-502 Glue application unit VC-710 End trimming unit IN-801 Top and bottom flush trimming unit RS-100 2 motorized multifunction profiling units - contour milling unit CR-202 (FAST system with 4 standard positions) Scraper unit RBK-503, NC 2 positions Flat scraper RCC-701 Workpiece thickness: 10-65 mm Max. workpiece height with contour milling unit (depending on profiles): 35-65 mm Edge thickness from roll: 0.4-3 mm Edge thickness from strip material: 0.4-22 mm (depending on unit) Minimum workpiece length: 140 mm Minimum workpiece width (with length 140 mm): 85 mm Minimum workpiece width (with length 250 mm): 50 mm Feed speeds: 10-14-18-20 Central extraction connection: 200 mm Extraction connection, edge banding: 80 mm Hodpfjv R Nk Usx Acvjk Extraction connection, joint milling: 120 mm Glue pot capacity: approx. 3 kg Heat-up time at half fill: approx. 10 min Length: 6000 mm Width: 1780 mm Height: 1770 mm Machine is offered without the workpiece return unit shown in the pictures Availability: short-term Location: Flörsheim

Condition: ready for operation (used), Year of construction: 1992, functionality: fully functional, type of input current: three-phase, plate height: 50 mm, From business closure Type: IMA Compact 309 C Year of manufacture: 1992 For roll material and strips up to 9mm thickness - Gluing with hot-melt adhesive granulate - End trimming - Sawing - Flush milling - Scraper knives and buffing Payment in cash upon collection. Private sale – no warranty. Hsdpfx Acox Avcdovjk

Condition: good (used), Metal band saw, fully automatic, band saw machine, band saw, vertical band saw, horizontal band saw, hydraulic horizontal band saw machine, automatic band saw, metal band saw machine -Manufacturer: Pehaka, horizontal band saw automatic band saw -Drive: 0.8 kW -Cutting data flat: 320 x 150 mm -Cutting data square: 150 mm Hsdpfx Aehwxb Tjcvjk -Saw blade speed: continuously adjustable, 20 - 195 m/min -Saw band: approx. 3700 mm -Coolant system -Dimensions: 1800/940/H1310 mm -Weight: 528 kg

Condition: excellent (used), Year of construction: 1981, functionality: fully functional, Sharpening machine for band saws with blade widths up to 360 mm. Feed from the left. 3 switchable built-in tooth profiles. Infinitely variable feed gearbox. Linear feed system. Grinding wheel diameter: 250 mm. Central electric height adjustment for adapting to different blade widths. Heavy-duty support and return rollers. Machine was completely overhauled in 2005. Hodpfx Asyvtbgscvek

Condition: excellent (used), Year of construction: 2001, machine/vehicle number: 0-200-24-6287, functionality: fully functional, input voltage: 400 V, input current: 56 A, edge thickness (max.): 20 mm, Equipment: CE marking, Used single-sided HOMAG edge-banding machine for straight edges – KL 78/A20/S2 For pre-milling (jointing trimming), gluing and post-processing of various kinds of edging materials. Fixed stop on the left side. Year of Manufacture: 2001 Hedjyv Da Hjpfx Acvjk SPEZIFICATION & EQUIPMENT: Basic machine with 80 mm wide conveyor chain with rubber-coated chain pads, - workpiece thickness max. 60 mm - top pressure with compound V-belt, motorized height adjustment (to workpiece thickness) - panel support with roller guide, extractable approx. 700 mm - clamping of glue application unit before rear end of workpiece, for even glue application - glue roller drive in case of feed stop - hand switch /remote control for setup – mode - adjustable infeed fence with NC-axis (CAN-bus) - Jointing trimming 2 motors (clock-wise, counter clock-wise), 2x4kW, jumping function GLUING SECTION A20, consisting of: - QA34 glue application unit, on request with PTFE-coating (Teflon) - Pre-melter for EVA glues - Edge magazine, edge thickness min. 0,4 mm to max. 20 mm Edge width (height) max 65 mm - Pressure zone with automatic horizontal adjustment (NC CAN-axis) to edge thickness, 1 driven & 6 non-driven pressure rollers. POST-PROCESSING SECTION: - Snipping (end-trimming) unit HL81, 2 motors, with straight/chamfer cutting function motorised fine-positioning of snipping stop - Pre-milling (rough trimming) 1,5 kW, top/bottom - Corner rounding FK13, 2 motors (top/bottom) with automatic 8-fold tool changer and several exchangeable trimming heads - Profile (radius-) scraping MN21, with NC-axis positioning - Flat scraping (glue joint) FA10, top/bottom, (version with 3 tracer rollers) - Straight belt sanding unit KS10 - Buffing unit top/bottom ELECTRONIC CONTROL: - HOMATIC NC21 OPERATING SYSTEM

Condition: good (used), Year of construction: 1999, functionality: fully functional, Pacific P V 12 - F, year 1999 Power: 12.5 kW Edge thickness: 0.2–12 mm Feed: 12 m/min Glue application roller, synchronous and counter-rotating Automatic infeed fence Jointing/edge trimming End trimming up to 3 mm Flush milling at 15°, 30°, 45° Radius milling R 2 – R 5 Flush sawing Corner rounding Radius scraper blade Schwabbl cleaning unit Extendable roller support Compressed air: 6 bar Hodpfjw Ni Nrjx Acvok Dimensions: 5400 x 1000 x 1400 mm Weight: 2300 kg

Condition: new, Technical data:Rated voltage 230 VRated input 3050 WEdge height 10 - 65 mmSwiveling range 0 - 50 °Edge thickness 0.4 - 3.0 mmHeating time 30 sTemperature max. 520 degrees CelsiusFeed stepless 1 - 5.5 m/minDimension (L x W x H) 220 x 160 x 360 mmConnection compressed air 6 - 10 barInner radius min. 10 mmWeight 10.8 kg Hjdpfx Acowi Nt Eovek

Condition: used, Year of construction: 2011, used, in excellent condition, low operating hours Manufacturer: Lange Model: B85K Year of manufacture: 2011 Machine no.: 132 CE type-certified Edge thickness: 0.4 – 3.0 mm Max. workpiece height: 50 mm Min. workpiece width: 75 mm Min. workpiece length: 120 mm Feed rate: 7 m/min Cutting from the coil Cutting unit: 0.2 kW Flush milling - chamfer milling: 2x 0.27 kW Flat scraper Extraction connection D 120 mm Space requirement approx. 2200 x 1130 x 1300 mm Hedpfx Acoyu U Epevek Weight approx. 600 kg Total connected load 2.5 kW Warehouse location: 97447 Gerolzhofen, loaded free on truck, unpacked Delivery in as-inspected condition, without warranty or guarantee.

Condition: ready for operation (used), Year of construction: 2023, machine/vehicle number: 232597, functionality: fully functional, cutting height (max.): 320 mm, controller model: SIEMENS SIMATIC HMI, saw band length: 5,080 mm, throat depth: 370 mm, No minimum price – guaranteed sale to the highest bidder! By placing a bid, you commit to timely collection, either between 11.05.2026 and 13.05.2026 or between 18.05.2026 and 21.05.2026! TECHNICAL DETAILS Belt length: 5,080 mm Material feed height: 1,200 mm Roller diameter: 630 mm Throat depth: 370 mm Max. cutting height: 320 mm Guide bar (hydraulic stroke): 200 mm Belt tension (hydraulic stroke): 60 mm Belt speed: 250 – 2,000 m/min MACHINE DETAILS Control system: SIEMENS SIMATIC HMI Operating voltage: 400 V Rated current: 32 A Hedpfx Asyng Atscvsk Dimensions & Weight Dimensions (L x W x H): 2,700 x 2,500 x 2,700 mm Weight: 2,100 kg EQUIPMENT Roller conveyor (roller conveyor width: 350 mm) External reference: Heraeus

Condition: used, Year of construction: 1985, edge thickness 0,4 - 12 mm work piece thickness 10 - 55 mm work piece length min 160 mm work piece width min 65 mm feed speed 13 m/ min compressed air 7 bar machine length 5420 mm weight 1950 kg glue pot with quick melt system glue application roller wit left and right turning edge magazine for PVC and strips motor height adjustment for pressure beam pneumatic pressure rollers for edge magazine control panel, rotatable all aggregates in-line controlled cutting Hodpfsc Tmygsx Acvjk milling combination with 2 aggregates, 1st aggregate straight, 2nd aggregate radius and phase milling tool draw blade buffing unit central lubrication for transport chain quick change system edge control system with error msg IR heater CE Advise used machines: • Technical data without obligation, mistake and intermediate sale reserve. • Price is considered ex-location price • All articles or machines are bought as seen without any entitlement on warranty. • It is left to the choice of the buyer to view the machines before at its location. • Special arrangements are possible but only valid in written form. (We answer your inquiries only with stated address + telephone number!)

Condition: used, Vertical band saw PEHAKA type SM 4 make no. 27060 year of construction approx. 1980 throat 380 mm table size 620 x 480 mm cutting height 250 mm roller diameter 400 mm working height 1120 mm saw band length min. 2900 - max. 3100 mm saw band speed 22-125 m/min. infinitely variable motor power 0,6 / 0,75 kW Hsdpjiv A U Esfx Acvok mains connection 380 volt, 50 Hz - infinitely variable saw band speed via Vario belt drive with lever adjustment and 2 motor speeds - saw table tiltable +/- 15 - Saw blade butt welding machine IDEAL BS 0-16 - Saw blade shear - substructure made of U-steel 100 x 50 mm , movable with lift truck space requirement L x W x H 1050 x 800 x 1950 mm weight 355 kg good condition

Condition: new, Year of construction: 2025, Joining unit: Yes Edge thickness: maximum 3mm Workpiece thickness: from 8mm - 50mm Workpiece width: minimum 110mm Glue basin: granular, quick change basin cross-cut shear: yes cross-cutting / flush sawing: yes Milling station: chamfer / radius corner copying: yes Flat - scraper: yes Radius scraper: Yes Buff: Yes Hodpfjk Eai Uox Acvek Non-stick spray unit: Yes Infeed ruler adjustment: manual workpiece thickness adjustment: manual power input: 5 kW machine length: 3314 mm Machine width: 1085 mm Weight: 545 kg

Condition: used, Year of construction: 2008, Used machine Year of manufacture: 2008 Features and technical specifications: Hodpfx Asyqanbecvek - Round pot glue application unit - With second glue application unit for PUR processing - Feed unit with automatic edge band magazine - Pressure zone with multiple pressure rollers - End trimming: 2 motorized saw units for front/end cap cutting - Top/bottom milling units: 2 milling units with tracing wheels for radius or chamfering - Radius scraper blade: pneumatically operated, post-processing of radii - Surface scraper blade: for smoothing the edge surfaces - Polishing unit: 2 polishing wheels with motors for final finishing - Riepe spray device - Control: PLC with control panel - Feed frequency inverter replaced by Ott in 2022 - Feed speed approx. 10–12 m/min - Workpiece thickness up to 52 mm - Edge thickness 0.3 – 12 mm - Power supply 3x 400 V AC, 50 Hz - Rated power 12.7 kW - Rated current 30.5 A - Control voltage 24 V DC - Max. fuse protection 35 A (5x 6 mm² connection cable) Machine dimensions: approx. 6120 x 840 x 1385 mm Machine weight: approx. 3,000 kg Availability: short notice Location: Röllbach

Condition: good (used), Year of construction: 2011, machine/vehicle number: 08420, functionality: fully functional, edge thickness (max.): 3 mm, total length: 11,500 mm, overall weight: 8,500 kg, compressed air connection: 7 bar, Used single-sided IMA edge banding machine for straight edges; for jointing, gluing, and finishing various edge materials. Fixed stop side on the right. IMPORTANT: Incl. LIGMATECH return conveyor WORKPIECE & MATERIAL DIMENSIONS: Min. workpiece length : 150 mm Min. workpiece width : 65 mm Min. workpiece thickness : 8 mm Max. workpiece thickness : 40 mm (with corner rounding / copy function) Max. workpiece thickness : 60 mm (without corner rounding / copy function) Smallest workpiece : 150 x 150 mm, or 300 x 65 mm Workpiece overhang : 38 mm Edge thickness min/max : 0,3 – 3,0 mm Edge width min/max : 14 – 65 mm EQUIPMENT / SPECIFICATION BASIC MACHINE - Basic machine with 80 mm wide conveyor chain as workpiece transport device - Feed speed 6 to 30 m/min, adjustable from machine control - Top pressure with pressure-loaded guided rollers and 70 mm wide V-belt - Automatic height-adjustment of top pressure (thickness) - Workpiece support with rollers, extendable up to approx. 700 mm - Infeed table IMA 63.152, 500 x 500 mm, for easy feeding of long & narrow boards - Infeed device (manually) tiltable, with 5 driven rollers from top - Adjustable infeed guide/fence via NC axis AGGREGATES / EQUIPMENT - JOINTING TRIMMING/pre-milling (08.378), 2x4.5 kW, controlled (jumping), tool-Ø 125 mm Electronic horizontal positioning - GLUING AGGREGATE 04.1570 Concept, driven glue roller with automatic feed stop in case of error, Quick-lock system for glue application unit, Glue roller lift-off when feed stops Edge feed controlled by light barrier, upper edge guide w. step-motor, electronically controlled - Automatic PUR pre-melting system 283.203 - 6-fold automatic roll-change edging magazine POST-PROCESSING SECTION - End-trimming (snipping) unit 08.42, horizontal version, 2 motors each 0,65 kW, 200 Hz For straight and chamfer cutting, max. working speed 30 m/min - Fine trimming unit 08.055, 0,66 kW 400V 200Hz, top/bottom, HSK 25 - Corner rounding 08.348, 2 motors 0,66 kW 400V 200 Hz, HSK 25 Max. working speed 20 m/min - Profile scraper 08.516, top/bottom, for multi-profile-knives, automatic positioning by Hodpfx Acewyp Nusvjk step motors, max. 4 profiles, with electro pneumatic horizontal move-in/-out - Spraying devices for cleaning agent. - Flat scraper 08.521 (glue joint scraping), top/bottom - Profile (corner-) buffing 08.604, 4 motors - Buffing unit 08.617, top/bottom CONTROL / SOFTWARE: • Control system ICOS open compact • Flexible edge control • Uninterrupted power supply (UPS) • Power supply 400 V, 50/60 Hz, Control voltage 24 VDC / 230 VAC Machine dimensions (occupied area when installed) L 1150 x W 300 x H 260 cm Available: October 2025

Condition: excellent (used), Double side - Stand-alone Machine (or 1st and/or 2nd in a line) Edges (band in rolls) thickness (Min/Max) mm 0.3 / 3 Edges thickness in stips / lippings mm 1,3 Panels thickness (min/max) mm 8 / 40 Working width (min/max) mm 266 / 2400 (option 3000) Distance (center-axes) of the Disappearing Dogs (mm) 540 (prepared for 270 mm) Numerical Control ICOS OPEN Feeding speed (adjustable) max. 60 m/min Without Transmission bar (Master & Slave system) SIZING PART (for each side): Spraying unit (Anti-sticking liquid) Pre-milling Unit (vertical joint trimmers) 08.376 (KW 4.5 x2) Free space EDGE-BANDING PART (for each side): Glueing Unit (Hot Melt Glue) 283.205 Band Pressure zone. Edge coils supporting unit (No. 2 reels) Servo-drive Snipping (end-cutting) unit 08.42 (KW 0.2 x 2) 0°-25° (max. working speed 50 m/min) Fine Trimming unit 08.055 (KW 0,66 x 2) 0°-30° Multi Function Unit (Profile contour Trimming unit) 08.342 (KW 0.66 x 2) Spraying Unit (for polishing liquid) Hjdpfx Acou Ekbnjvek Free space (for possible addition of a scraper) Buffing unit 08.617 (Kw 0.18 x 2)