Used Bale Press for sale (12,503)

Condition: used, Year of construction: 1994, operating hours: 62,058 h, functionality: limited functionality, machine/vehicle number: 099314, bale width: 770 mm, bale height: 520 mm, Manufacturer: COMDEC - PAAL Model: LV2020PFT Serial number: 099314 Lhjdpfet Ucqfsx Ahbog Year of manufacture: 1994 Maximum capacity: 25,000 kg/h Bale discharge dimensions: 77 cm x 52 cm The press was in operation until the production line was shut down.

Condition: good (used), Year of construction: 2011, operating hours: 40,000 h, functionality: fully functional, pressing force: 88 t, filling opening width: 990 mm, filling opening length: 1,800 mm, bale length: 1,200 mm, bale width: 1,100 mm, bale height: 750 mm, overall weight: 23,000 kg, oil tank capacity: 2,000 l, power: 90 kW (122.37 HP), volume flow: 643 m³/h, Good day, We hereby offer, subject to prior sale, a used baler including conveyor belt, wire tying stations, and bale chute from the manufacturer HSM GmbH + Co. KG, model VK 8818 FU. The following technical specifications were taken from the manufacturer's operating manual and brochures; we do not assume any liability for the correctness or completeness of this information. Manufacturer: HSM GmbH + Co. KG, Germany Model: VK 8818 FU Year of manufacture: 2011 Operating hours: approx. 40,000 hours as of July 2025 Main press force: 880 kN Specific press force: 107 N/cm² Feed opening dimensions: 990 x 1,800 mm Theoretical throughput: 643 m³/hour Ljdpfeymmtcsx Ahbshg Bale dimensions: 1,100 x 750 mm, length adjustable from 600 up to 2,000 mm Drive power: 2 x 45 kW, frequency-controlled Tying: 5-fold horizontal, fully automatic Baler dimensions (set up): 12,130 x 4,800 x 3,270 mm (L x W x H) Overall installation dimensions with conveyor system: 14,000 x 23,000 x 7,745 mm (L x W x H) Note: The machine was used in a recycling facility for compacting paper, cardboard, and film. The press is in good condition and will be replaced with a new, larger press in May/June 2026. Until then, the machine can be inspected in operation with material. We would be pleased if this baler is of interest to you. Your Mertens & Frowein GmbH service team

Condition: ready for operation (used), Baler Hsm vk 42/1200 fully automatic Pressure force: 42 tons Beam dimensions: 700 x 800 x 600 - 1200 mm Beam weight: approx. 450 kg Press length approx. 7 meters press weight approx. 6000 kg Lhjdpfxora Nrxs Ahbeg tying 4 x wire automatically

Condition: good (used), - Large filling opening, ideal for large boxes - Container tipper for convenient filling Lhedpfx Asv Amv Eohbog Pressing force in kN: 400 Bale length: 1,100 mm Bale width: 750 mm Bale height: 750 mm Press length: 5,640 mm Press width: 1,674 mm Press height: 2,500 mm Weight: 4,450 kg - Motor power in kW: 9 - Voltage/frequency: 3 x 400 V / 50 Hz - Bale weight in kg (depending on material): up to 350 kg - Manual binding: 3 times with wire Year of manufacture: 2013 HSM HL 4010 LI baler - Large filling opening, ideal for large boxes - Container tipper for convenient filling Pressing force in kN: 400 - Motor power in kW: 9.5 - Voltage/frequency: 3 x 400 V / 50 Hz - Bale weight in kg (depending on material): up to 350 kg - Manual binding: 3 times with wire Year of manufacture: 2012

Condition: excellent (used), Baling press Hsm HL 4809 - Large filling opening, ideal for large boxes - Container tipper for convenient filling Power in kN: 480 - Motor in kW: 10.7 - Voltage/frequency: 3 x 400 V / 50 Hz - Bale weight in kg (depending on material): up to 400 kg Lhjdpsv Ak Npjfx Ahbeg - Bale dimensions length x width x height in mm: 1200 x 1100 x 750 - Dimensions of the device length x width x height in mm: 5648 x 1849 x 2515 Idle cycle time in seconds: 53 - Manual tying: 4 times with wire Year 2015-2017 Complete baler, side housings unscrewed for transport Balers after inspection by an authorized service center

Condition: excellent (used), Year of construction: 2022, operating hours: 8,856 h, functionality: fully functional, working length: 12,000 mm, Press Refurbished 12m length Everything in perfect condition Operational Lhjdpfx Aexfg Sbjhbsg Located at company headquarters.

Condition: excellent (used), Year of construction: 2014, functionality: fully functional, pressing force: 26 t, filling opening width: 1,500 mm, filling opening length: 630 mm, bale length: 1,500 mm, bale width: 800 mm, bale height: 1,140 mm, bale weight: 500 kg, total width: 1,060 mm, total height: 2,576 mm, total length: 2,075 mm, overall weight: 1,220 kg, noise level: 65 dB, power: 4.6 kW (6.25 HP), Powerful bale press Orwak 3820 Power. Extra good machine for big dimensions cardboard or foil because of the extra large feed opening 1500 x 630 mm. Ljdpfx Ajxmvc Eehbjhg

Condition: new, Year of construction: 2024, functionality: fully functional, OSAMA S2R 1300 roller gluing machine for cold gluing. Lhjdpfx Aevxai Rshbjg Brand NEW. Packed by the producer OSAMA in Italy.

Condition: excellent (used), Year of construction: 2020, machine/vehicle number: 161.40.492, Used Strautmann bale press, type: BalePress 3, serial number: 161.40.492, year of construction: 2020, with tape extraction hook Ljdpfxevvk T Ie Ahbjhg Power supply: 230 V 50 Hz Electrical Power: 0,75 kW Protection class: IP54 Pressing force: 27 kN Press stroke: 580 mm Weight of the machine: 275 kg Transport dimensions (lxwxh):1070 x 754 x 2110 mm (without pallet) 1070 x 754 x 1945 mm Filling opening (wxh): ca. 700 x 450 mm Cycle Time: 27 sec. Bale weight 30 kg Bale size in the chamber (lxwxh)*: 500 x 700 x 500 mm Bale tying: strapping with two twines, PP band ADVANTAGES Easy to install and transport Easy to handle bales Practical emptying of bales Foil/cardboard mode switch Simple and safe operation Stable door locking system Stable guide of the press plate "D" level security system. Small space required BP3: Bale tying system with open door; BP3CD: tied bales with door closed Solid construction Wheel door lock Ideal for small shops. The Strautmann BalePress 3/3CD is a small, single-chamber baler. At the same time, it is perfectly suited for baling common and smaller quantities of paper, foil, PET bottles and plastic waste and, thanks to its compact design, it can also fit into a very small space. It is clearly the best alternative for our partners with less waste and a waste container with a small footprint. Depending on the pressed material, the 3 ton pressing force can result in a volume reduction of up to 90%. The machine can produce relatively small and therefore easy to handle bales of up to 35 kg. By using it, significant savings in storage and transportation costs can be achieved. Bales are easier to transport and sell than untreated waste. Due to its dimensions, the machine can also fit in a very small space, and because of this, the baling technology is no longer available to our partners who have limited space. Price 3.490 Euro + VAT, negotiable, FCA: Oradea/Romania Irrtum, Anderungen und Zwischenverkauf vorbehalten / Subject to errors, changes and prior sale / Ne rezervăm dreptul la greșeli, modificări și vânzare We speak English. /Wir sprechen Deutsch./ Beszélünk magyarul. /Nous parlons français/Vorbim romana

Condition: used, Year of construction: 1995, functionality: limited functionality, cutting force: 800 t, empty load weight: 190,000 kg, type of input current: three-phase, Arnold HS850 Scrap & Metal Presse Die Maschine befindet sich derzeit in transportbereitem Zustand. master cylinder cylinder force: 850 t press: 0.08m/s hold-down cylinder cylinder force: 100t / per cylinder feed cylinder: cylinder force:100t cover cylinder: cylinder force:100t main dimensions total length:16175mm total width:5200 total height: 6420 mm Dimensions: Passage width at the scissor stand: 800mm passage height at the scissor stand: 800mm total height: 6000mm weights: scissor stand with cutter bar: 60 ton feed device approx: 85 ton total weight: about 170 tons required amount of oil: 5200 liters connection value of the machine: 220kw Lhodpfxoh T Dcto Ahbog If you need more information. We are here to help! Please contact us using the contact form or give us a call Your ad has been automatically translated. Translation errors are possible.

Condition: ready for operation (used), Year of construction: 2009, operating hours: 8,500 h, functionality: fully functional, fuel: diesel, IDROMEC 650 diesel engine plus generator, ready to use Lhjdoyg Hcdspfx Ahbeg

Condition: reconditioned (used), Year of construction: 1996, functionality: fully functional, pressing force: 170 t, filling opening width: 1,020 mm, filling opening length: 1,800 mm, bale width: 1,100 mm, bale height: 1,100 mm, bale weight: 900 kg, overall weight: 40,000 kg, oil tank capacity: 3,000 l, year of last overhaul: 2025, volume flow: 750 m³/h, For sale is a used baling press system consisting of a chain belt conveyor for underfloor operation, with a feed hopper, a hydraulic pre-compactor with ruffler, a MACPRESSE 111A baling press, two complete wire drawing frames with 5 wire reel stands each, without wire. Technical data baler: Manufacturer MACPRESSE EUROPA S.R.L. Typ 111A Year of construction 1996, refurbished in 10/2024 Press power main press 170 tons Specific press capacity 14 kg/cm² Feed channel 1,800 x 1,020 mm Filling volume 2,5 cm³ Theoretic throughput rate 750 m³/h Bale size 1,100 x 1,100 mm, length variable Driving motor 2 x 55 kW Tying system 5-fold horizontal, full automatic Throughput rate at a approx. 30 up to 35 tons/h, depends on material Volume hydraulic oil tank 3,000 l Transport dimensions of press with new machine feets 113,700 x 2,300 x 2,900 mm (l x w x h) Machine weight baler approx. 40 tons Comments: The baler was partially overhauled in our workshop and tested after completion of the work, please look at our functional video. The system was previously used to bale paper and cardboard from municipal collections. The contract was awarded elsewhere after the end of the contract period, so the complete system is for sale. The overhaul work carried out and the spare parts replaced can be found in the detailed photo documentation and in our quotation. The documentation (Manual, CE, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors. Technical data conveyor belt: Manufacturer Wagensfeld B.V. Type chain belt conveyor 1700 mm Year of construction 2017 Drive power 7.5 kW Belt speed 14 m/minute Length of infeed conveyor 6,900 mm Length of ascending belt 12,885 mm Length of gooseneck 1,747 mm Overall length 21,271 mm Pitch 32° Effective width 1,644 mm Height of drive shaft above ground 5,777 mm Wall height of feed conveyor 500 mm Wall height of ascending conveyor 880 mm Steel flights height 40 mm Distance between flights 1200 mm Transport dimensions conveyor disassembled 15,005 x 2,503 x 2,435 mm (l x w x h) Pit dimensions 11,500 x 2,700 x 1,015 mm (l x w x d) Lhsdpfey S Rqwsx Ahbeg Remarks: The chain belt conveyor, built in 2017, was later made to fit the baler during the last installation of the baler in the Netherlands and is newly installed. The conveyor belt is in good, operational condition and has therefore not been overhauled. An installation drawing with the pit dimensions is available. Scope of delifery: 1 chain belt conveyor, Wagensveld B.V. 1 piece feed hopper with pre-compressor flaps 1 piece wirbulator 1 baler MACPRESSE, type 111A 2 wire drawing frames with wire reel stands, without wire 1 operating manual with CE declaration, electrical and hydraulic circuit diagram

Condition: reconditioned (used), Year of construction: 2009, operating hours: 22,029 h, functionality: fully functional, pressing force: 80 t, filling opening width: 1,400 mm, filling opening length: 1,100 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 600 kg, overall weight: 16,000 kg, power: 75 kW (101.97 HP), year of last overhaul: 2025, volume flow: 300 m³/h, Technical data baler: Manufacturer Avermann Maschinenfabrik GmbH & Co. KG, Germany Type AVOS 1410-45/80 Year of construction 2009 Operation hours 22,029 hours, as of December 2025 Press power main press 80kN Specific press force 103,9 N/cm² Feed channel 1,400 x 1,000 mm Theoretic cycle time 12 sec Lhjdpfx Ahoy R Nnfobog Theoretic throughput capacity 300 m³/h Bale size 1,100 x 750 (w x h), the length is variable Drive power 45 kW Connected load 75 kW Tying system 4-fold, vertical, fully automatic Throughput capacity at a bulk weight of 30 kg/cbm approx. 6,0 t/h bulk weight of 50 kg/cbm approx. 10,5 t/h bulk weight of 100 kg/cbm approx. 17,5 t/h Bale weight with a bale length of approx. 1.2 m up to 600 kg, depends on material SPS controller Siemens S7-300 Operating panel pulsotronic Baler dimensions built up 8,610 x 2,400 x 3,835 mm (l x w x h) Transport dimensions 8500 x 2450 x 2950 mm (l x w x h) Transport weight baler approx. 16 t Special equipment: Wear-resistant floor made of HARDOX steel Special press ram for pressing ‘difficult’ materials and loose bulk materials with small grain sizes Control cabinet air conditioning Machine foot elevation 200 mm Remark: The machine was serviced and partially overhauled in our workshop. The following work was carried out and parts replaced: • Dismantling of the press ram, disassembly into individual parts, reconditioning of the mechanics, replacement of the following plastic wear plates and rails: o Plastic wear rails left/right under the press ram o Plastic wear rails left/right above the press ram o Plastic main wear plate (support plate) in the centre under the press ram • Steel guide rails on the left/right in the frame • Replacement of the entire base plate, four-piece, made of wear-resistant HARDOX steel • Wire inlet rails in the press floor newly welded and smoothed • Replacement of the counter blade, two-piece, in the frame • Adjustment of the blade gap to approx. 2.5 mm • Dismantling of the binding and twisting unit, disassembly into individual parts, loosening of the mechanics, replacement of all deep groove ball bearings and axial ball bearings on the twisting shafts, wire blades cleaned and readjusted, chains greased and tensioned • Support roller in front of the twisting shafts replaced • All hydraulic hoses replaced • Oil filter and air filter replaced • Main hydraulic cylinder checked for leaks • The hydraulic oil is only one year old, has been chemically analyzed, is still in good condition, and has therefore not been changed but can continue to be used. • General maintenance work carried out Finally, the press was subjected to a machine test in manual and automatic mode; see the video for the machine function test. Comments: The documentation (operating instructions, CE declaration, electrical/hydraulic circuit diagram) for the press is available.

Condition: used, High-performance baler MACFAB - BEMA type 650A Hydraulic press for packaging waste, recyclable renewable raw materials, secondary raw materials Manufacturer no. MF J0162 Year of manufacture 2021 Pressing force 50 tons. Press plate stroke approx. 1000 mm Cycle time per stroke approx. 40 sec. Pressing chamber floor area 1500 x 1100 mm Pressing chamber height 1650 mm Filling opening 1500 x 870 mm Filling height approx. 1250 mm Bale format 1500 x 1100 mm Bale height max. 1100 mm Hydraulic operating pressure 200 bar Motor power 5.5 kW Mains connection 400 volts, 50 Hz, 12 amps. - with two hydraulic cylinders - Door locking via threaded spindle with handwheel - Pressing operation only with the pressing chamber door closed - 2-hand operation for hydraulic tipping of the finished pressed bale - Free space for manual strapping - Standard industrial bales of 1500 x 1100 x 1100 mm are produced - the highly compressed bale is automatically tipped onto a pallet - only 62 operating hours Space requirement L x W x H 2120 x 1350 x 3220 mm Height for transport with lowered hydraulic cylinders approx. 260 cm Weight 1.8 ton. Ledsvq Rtkjpfx Ahbohg The machine is in very good condition, as good as new. The press has a new price of EUR 22,200 net at BEMA The BEMA company also buys the packaging waste that you press into bales with this press.

Condition: used, Year of construction: 1988, operating hours: 1 h, machine/vehicle number: V 516, total width: 2,000 mm, total length: 7,000 mm, total height: 1,800 mm, operating pressure: 300 bar, pressing force: 90 t, sheet thickness aluminum (max.): 5 mm, power: 11 kW (14.96 HP), empty load weight: 16,000 kg, cutting force: 90 t, year of last overhaul: 2025, Bale size 400x400 mm Force 1 Step 900 KN Force 2 Step 900 KN Steel max. 2500-3500 Kg/Std. Aluminium max. 2000 - 3000 Kg/Std. Driving Power 11 KW Arrangement Surface 7x2x2,5 m x m Machine weight 16 to Place: Austria Ljdpfxjlhqd Ro Ahbehg Aviable: 30.01.2025

Condition: ready for operation (used), Year of construction: 2012, pressing force: 40 t, Manufacturer: HSM Lhodpfx Ahsx D U N Sobsg Model: HL 4010 Year of manufacture: 2012

Condition: good (used), Manufacturer: Comp Tip: SB5 Engine: 2,2 KW Cylinder stroke length: 500 mm Chamber size: 500 x 350 x 400 mm Lodpfjh Eic Asx Ahbshg

Condition: used, Year of construction: 2012, pressing force: 4 t, HSM V-Press 504 waste paper baler - used The HSM V-Press 504 vertical baler is a compact yet extremely efficient device designed for pressing cardboard and plastic waste. Thanks to its robust construction, simple operation, and modern control system, this model is the ideal solution for manufacturing companies, warehouses, stores, and logistics centers where significant amounts of packaging waste are generated every day. The baler, manufactured by the German brand HSM, ensures reliable operation and a long service life. Key advantages of the waste paper baler: 40 kN crushing force – effective waste compression, reducing volume by up to 95%. Efficiency and ergonomics – the crushing process starts automatically when the door is closed, and the piston returns to its starting position automatically. Modern control system – a microprocessor with a membrane keyboard and graphic text display ensures easy monitoring of the work process. Double door with lever – safe and convenient operation even with intensive use. Compact bales up to 60 kg – facilitate transport and storage of processed waste. Integrated bale ejector – increases operator safety and comfort. Energy-efficient operation – 1.1 kW motor allows for full functionality with low energy consumption. Stable, durable construction – guarantees reliability over a long service life. The offer applies to the HSM V-Press 504 waste paper baler: • Product code: MTP006524 • Product condition: used • Year of manufacture: 2012 • Model: V-Press 504 • Width: 102 cm Lodpfx Asyim Ayohbjhg • Depth: 81.5 cm • Height: 193 cm • Weight: 290 kg • Power: 1100 W • Voltage: 230 V Net price: €2,859.00 per unit * I have large quantities available, with the possibility of negotiating the price for larger orders. * Transport possible throughout Europe. * The above offer does not include transport costs. * Location: Chmielów/Tarnobrzeg, Poland.

Condition: used, Year of construction: 1988, pressure 400 t distance between columns 1100 mm stroke 250 mm no. of strokes 25 - 75 /min Lhedpfx Ahsvuuknjbeg distance table/ram, max. stroke up, adjustment up 900 mm table surface area 1100 x 965 mm capacity of ejector in table 30 t ejector stroke of ejector in table 80 mm capacity of ejector in ram 3 t stroke of ejector in ram 60 / 70 mm ram surface 980 x 800 mm column travel -side 800 mm ram adjustment 20 mm power capacity 80,0 + 5,5 kW weight 47,0 t Dimensions (WxDxH) 3,5 x 3,3 x 6,0 m weight of switch cabinet 1,4 t dimensions of electrical cabinet (WxDxH) 4,9 x 0,5 x 2,6 m Multi-station cold extrusion press with link drive with infinitely variable drive, hydraulic clutch-brake combination (Ortlinghaus), hydraulic overload protection in the slide, motorised slide adjustment, pneumatic counterbalance cylinder in press frame, cam-controlled ejector in table (30 t / 80 mm), pneumatic ejector in slide (3 t, 60 mm), motorised central lubrication

Condition: new, Year of construction: 2025, functionality: fully functional, input voltage: 380 V, input frequency: 50 Hz, stroke length: 200 mm, operating speed: 50 mm/s, reverse speed: 180 mm/s, table length: 3,200 mm, total length: 3,915 mm, total width: 1,605 mm, total height: 2,655 mm, overall weight: 8,000 kg, bending force (max.): 1,000 t, bending angle (max.): 90 °, warranty duration: 24 months, working height: 450 mm, All-Electric Servo Bending Machine Nominal force(KN): 1000 Slider stroke(mm): 200 Throat depth (mm): 360 X-axistravel(mm): 600 R-axistravel(mm): 200 Z-axistravel(mm): 2500 🔹 Smart CNC System – SL100-P with high-end algorithms and 12-inch touchscreen for intuitive operation. 🔹 High-Precision Structure – Finite element analysis (FEA), annealed, and one-time machining for long-term stability and accuracy. 🔹 4-Axis Intelligent Backgauge – AC servo-driven, high-speed positioning with automatic collision avoidance. 🔹 Precision Compensation System – Adjustable convex strips & fine-tuning mechanism for optimal bending accuracy. 🔹 Powerful & Durable Drive – High-torque servo motor, heavy-duty ball screws & sealed protection for longevity. 🔹 Fully Closed-Loop Control – Y1/Y2 magnetic scale feedback, positioning accuracy ±5μm. Lhedpfx Ahjv Hchlobog 🔹 Optimized Electrical System – Closed electrical box, heat dissipation, & neat wiring for reliability and easy maintenance. 🔹 Imported Precision Components – Ball screws & linear guides ensure accuracy without stroke compensation. 🔹 High precision, stability, and smart automation – designed for professional sheet metal bending!

Condition: used, Year of construction: 2025, total length: 1,450 mm, total width: 800 mm, total height: 2,200 mm, Empty weight: 970 kg Price: On request Movable Press-Cylinder - Year: 2025 - Documentation available: Yes - CE marking present: Yes - CE certificate present: Yes - Operating hours: 0 - Drive system: Conventional - Press model: C-Frame press - Press force [ton]: 100 - Max. stroke [mm]: 380 - Table length [mm]: 1500 - Table width [mm]: 300 - Ram length [mm]: 100 - Throat depth [mm]: 1100 - Height adjustment [mm]: 750 - Motor power: 3.0kW - Transport dimensions: 1450mm x 800mm x 2200mm (l x w x h) Lsdpfsw N Su Dsx Ahbehg - Transport weight [kg]: 970kg - Transport packages [pcs.]: 1 Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Lukas van Rossum

Condition: used, Year of construction: 2025, total length: 1,100 mm, total width: 800 mm, total height: 2,200 mm, Empty weight: 540 kg Price: On request Movable pressing-cylinder - Year: 2025 - Documentation available: Yes - CE marking present: Yes - CE certificate present: Yes - Operating hours: 0 - Drive system: Conventional - Press model: C-Frame press - Press force [ton]: 60 - Max. stroke [mm]: 380 - Table length [mm]: 1000 - Table width [mm]: 260 Lodpfx Ahow N St Hebohg - Ram length [mm]: 100 - Throat depth [mm]: 750 - Height adjustment [mm]: 750 - Motor power: 2.2kW - Transport dimensions: 1100mm x 800mm x 2200mm (l x w x h) - Transport weight [kg]: 540kg - Transport packages [pcs.]: 1 Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Lukas van Rossum

Condition: used, Year of construction: 2025, total length: 1,300 mm, total height: 1,400 mm, total width: 800 mm, Empty weight: 800 kg Price: On request - Year: 2025 - Documentation available: Yes Lsdpexixrusfx Ahbehg - CE marking present: Yes - CE certificate present: Yes - Serial number: HB10011N2025006 - Operating hours: 0 - Control: Teach-in - Motor power: 4.0kW - Transport dimensions: 1300mm x 800mm x 1400mm (l x w x h) - Transport weight [kg]: 800kg - Transport packages [pcs.]: 1 Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Lukas van Rossum

Condition: used, Year of construction: 2025, total length: 1,200 mm, total width: 800 mm, total height: 1,800 mm, Empty weight: 450 kg Price: On request Lhodpfx Asxixrhjhbeg - Year: 2025 - Documentation available: Yes - CE marking present: Yes - CE certificate present: Yes - Serial number: PB12093N2025005 - Operating hours: 0 - Drive system: Conventional - Number of rolls [pcs.]: 3 - Power [kW]: 1.5 - Shaft diameter [mm]: 155 - Capacity diameter round [mm]: 50 - Transport dimensions: 1200mm x 800mm x 1800mm (l x w x h) - Transport weight [kg]: 450kg - Transport packages [pcs.]: 1 Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Lukas van Rossum

Condition: used, functionality: fully functional, With this offer, you are purchasing a used ‘Xerox Versant 180 Press’ colour production system. Item for sale: 1 x Xerox Versant 180 Press with the following equipment: Includes FreeFlow Server or Fiery Server Includes Paperdeck A-CF03 Includes Booklet Finisher A-FN13 Includes SquareFold Unit SQF-104 Not the right equipment? It is no problem to configure the machine according to your requirements. Please feel free to contact us! Meter readings: Total: Approx. 267,310 pages Colour: Approx. 253,808 pages Black: Approx. 13,502 pages Condition: This offer is for a used device, which may show signs of wear (minor scratches or yellowing). The device has been tested for functionality. A test print can be seen in the photo. Packaging and shipping: Lsdpfx Ahjxnlbmebehg You are welcome to view the device during our business hours. Please make an appointment! Seaworthy packaging and worldwide shipping available on request! A function test will be recorded on video for you before shipping or collection. For more information, please feel free to contact us personally.