Bandsaw Missler deb410ce 410mm

Missler deb410ce

Condition: new, 900 mm 900 mm 900x900 mm saw band length 9300 x 67 x 1,1 mm table height 790 mm band speed 14 - 60 m/min Kledpfx Asfg E Hpeg Ujl total power requirement 11 kW weight of the machine ca. 8,45 t dimensions 4,485 x 1,68 x 3,15 m The semi-automatic, hydraulic saws from the X-tech line offer the best Saw technology and best performance when cutting special steels • The electro-welded machine frame and the steel saw frame meet requirements all cutting needs and eliminate vibration and noise. • The chip conveyor is hydraulically driven and the speed is adjustable • All movements of the machine (saw frame, vice, feed, Saw band guides) are carried out thanks to modern linear guides with high static and dynamic load performance, which also has very low sliding friction to guarantee. • Another characteristic feature is the roles for the Positioning of the material by a hydraulic motor are driven. They move at right angles to the material, and thus allowing optimal clamping of the material. • Thanks to the height control of the saw band position, the operator can place the band in place near the top edge of the material. After the cut is finished, the tape automatically raised back to the previous position. Alternatively you can also “Remain” can be selected in the lower position. During the The software compares the cutting load with the cutting cycle Default. This means that the sawing system can be stopped in the event of irregularities become. • The saw band is cleaned by two adjustable steel brushes. The drive takes place hydraulically. • The hydraulic unit including filter and pressure gauge guarantees one particularly quiet operation at constant pressure. • Finely ground carbide inserts that clamp the saw blade, complete with lateral, hardened and adjustable guide rollers. The adjustable one The tape guide automatically moves as close as possible to the material. • The saw band is tensioned via a hydraulic cylinder, which is carried out by the Machine software is controlled. The voltage is set according to a given Time automatically delimbed when the machine is idle or after a cycle has been carried out. • Automatic version with CNC control in the X-TECH 900 / 1200 models a feed length of 500 mm for the series for high production rates. • The material is carried by a table with seven rollers. These will driven by a hydraulic orbital motor through which the material can be placed precisely even under maximum load. • All guided movements are carried out by four recirculating ball guides with one high capacity for static and dynamic loading; strong reduced feed friction. Tempered and ground prismatic Guides. Price on request.

Condition: good (used), cutting range round steel at 45°: 250 mm, cutting range round steel at 90°: 280 mm, cutting height (max.): 330 mm, Saw capacity: 280 mm round 330 mm square Saw capacity 45º: 250 mm round 250 mm square Saw speed: 40/80 mtr.min. Sawbelt: 3.320 x 27 x 0,9 mm Saw angle: 0 - 60º Featured with: - Coolingunit Kjdpstt Nd Refx Ag Usll Country of origin: Italy Motor power: 1,8 kW Machine weight: 700 kg Machine LxWxH: 190 x 120 x 135 cm

Condition: good (used), Marble plate Length: 3500 mm Width: 1500 mm Thickness: 300 mm Height on feet: 930 mm Number of feet: 5 feet 1 small failure on the top (L 150 mm x W 20 mm) - see photo Weight: approx 3 T Kledpoig Hu Nofx Ag Ujl

Condition: excellent (used), We offer for sale the following Gránit-Mill 90 wood pelletizing presses, in the condition shown in the pictures, after the pelletizing plant has ceased operation. The machine is made in Hungary, our company has an excellent relationship with the manufacturer, and we can help you purchase parts. Drive and sticker handling is similar to the old CPM machines. The presses (with pine) are capable of 1.2-1.5 t/h/pc. Price: €29 900/press €49 900/ 2 presses Included in the price: pre-tank control cabinet dosing screw permanent magnet conditioner press motors pre-tank 1.1 kW feeder 1.5 kW conditioner 15 kW tablecloth 0.55 kW main engine 90 kW 3 stickers all three are made by La Meccanica barely used It has a 6 x 45 mm hole for pine 2 sets (total of 4) notched collars spare parts screws nuts breaker pin assembly aids Kodpfx Agsp T Twuo Usll Status: Engines and drives intact. Both machines tested. It is recommended to replace the neck bearing of the right machine. Smaller parts (such as the pellet cutter) must be replaced. There is no water supply, the place is prepared. The greasing method is manual, but central greasing can be easily installed. Summary: The machine on the left can be put into production immediately. It requires a minor service on the right side. If necessary, the machine can be tested at a pre-arranged time. Not in production, must be prepared. It is possible to check the mechanical durability and volume density of the produced pellets on site!

Condition: new, turning diameter over bed 410 mm turning diameter over slide rest 240 mm turning length 1000 mm turning diameter in the gap 530 mm turning speeds 65 - 1810 U/min Klsdpfx Agom Rlb Ns Uel centre height 205 mm spindle bore 52 mm tailstock quill taper MT 4 total power requirement 2,2 kW weight of the machine ca. 0,9 t dimensions of the machine ca. 1,9 x 0,8 x 1,3 m Center lathe with: 3-axis digital measuring system fully assembled electromagnetic main spindle brake auto. Feed in longitudinal and transverse direction safety relay Micrometer end stop coolant device 3-jaw lathe chuck with 1 set of turning and drilling jaws German operating instructions.

Condition: new, capacity 90 degrees: round 510 mm capacity 90 degrees: square 450 mm 650x450 band speed 15 - 100 m/min table height 844 mm dimensions of saw-band 5320 x 34 x 1,1 mm total power requirement 3,0 kW weight of the machine ca. 2,1 t dimensions of the machine ca. 1,9 x 2,87 x 1,3 m PROMOTIONAL PRICE!!! 2-column double miter band saw K-tech DG 62/45 HA-I • 2-column miter saw • Solid, yet easy to use • Material height sensor (automatic cut start detection) • Smooth running thanks to diagonal cutting, feed regulator + cutting pressure regulator • Solid material inlet roller • Removable chip tray (disinfection) • Energy-saving and low-vibration thanks to diagonal cutting • Control panel ergonomic, safe and free-standing Ksdpfxod Iipme Ag Ujll • Frequency-controlled saw drive 15 -100 m/min. • Hydraulic cutting pressure control valve • Hydraulic control of saw frame and vice • LEDs for monitoring all safety functions • Large-sized wheels (520 mm) a. • Clear miter adjustment up to 60° Semi-automatic function: 1. Tension the material 2. Saw starts 3. Lowering in rapid traverse to the beginning of the material or the same for series cutting cut 4. Saw blade off 5. Raise the frame until it is just above the material 6. Vice opens

Condition: new, Comparable to Behringer, Kaltenbach, Kasto, Jaespa, etc. Cutting range 90° Kledsh Tnd Aspfx Ag Usl Round: 260 mm Flat: 300 x 260 mm Smallest diameter: 5 mm NC-controlled, automatic material feed with hydraulic full-stroke material clamping Easy operation via NC control with plain text display Material advance function without reclamping for short section cuts Robust, linear-guided feed gripper with servo positioning for maximum precision Automatic adjustment of blade guides to material width Recommended options: Powered chip brush synchronized with blade speed Separate control panel 7" CE panel, network-compatible, up to 1000 data sets storable, history memory for various functions and data, etc.

Year of construction: 2006, condition: refurbished (used), HYDRAULIC PRESS MECAMAQ PRESSURE 350t STROKE 350mm TABLE LEFT RIGHT 600mm TABLE FRONT BACK 750mm POWER 15kw Dimensions: Height: 2,9m Ksdpfx Aofmqqlog Uoll Width: 1,9m Length: 1,3m Weight: 5.700 kgr

Year of construction: 2021, condition: new, TECHNICAL DATA type: gas-heated drive-through chamber furnace internal dimensions: (w x h x d): 2200 x 2350 x 3000 mm number of control areas: 2 Max. loading weight: approx. 2,5 t PLC: Siemens S7 Klodpfxjg Dgymj Ag Ujl

Condition: used, L-TEC Inverter TIG Welding Machine Type Inverter TIG 200 DC TIG welding machine for direct current (DC) Serial No. 184548 Year of manufacture: approx. 1994 Output: 200 amps = 60% duty cycle 155 amps = 100% duty cycle Kledodzqb Espfx Ag Usl Adjustment range: infinitely variable Current type: DC (direct current) Mains connection: 400 Volt, 50 Hz, 32 Amp plug - 4-meter hose package with central connection and hand torch - with remote potentiometer (foot switch) - gas pressure regulator - DC only - HF ignition Space required (L x W x H): 850 x 480 x 740 mm Weight: approx. 150 kg The welding test shows very good results when welding stainless steel with direct current. Overall in good condition.