Eccentric Press - Single Column

MÜLLER EXP 45 RV/HK

Condition: used, Year of construction: 1996, pressure 80 t throat 320 mm stroke 6 - 118 mm no. of strokes 30 - 80 Hub/min ram adjustment 70 mm Crodpfetycdkjx Aqvji table surface area 830 x 610 mm ram surface 650 x 400 mm column daylight (nach hinten) 630 mm total power requirement kW weight of the machine ca. 8,1 t dimensions of the machine ca. B 1,2 x T 1,9 x H 3,3 m Furnishing: - with gear transmission - fixed table - automatic stroke adjustment - automatic ram adjustment - hydr. Overload - Ejector - Grease central lubrication - Cover plate for drainage hole - Continuous speed control using a frequency converter - Machine is technically checked in our company and receives a new control cabinet with safety controls and touchscreen - current UVV test with braking time measurement

Condition: used, Single-column – Eccentric press WEINGARTEN Type EV 63 Machine No. 738 / 61 Year of manufacture 1962 Pressing force 63 tons Stroke 260 mm Table area 630 x 530 mm Table opening Ø 210 mm Slide area 315 x 260 mm Adjustable slide stroke 8-100 mm Slide adjustment 63 mm Tool holder bore Ø 40 mm, with clamping piece Installation height max 450 mm Stroke rate 115 strokes / min Compressed air requirement min. 4.5 bar Motor power 4 kW Power connection 380 Volt, 50 Hz Table height above floor approx. 750 to 900 mm - Electrical stroke release via foot switch or two-hand control - Overload protection by shear plate - Clutch-brake combination by WEINGARTEN friction-thread clutch with top dead center through-drive protection - Front crankshaft support bearing - Press table adjustable in height via 2 threaded spindles - Manual centralized lubrication - Control cabinet positioned beside the press - UVV (German trade association for accident prevention) for manual feeding operations Space requirement L x W x H 1750 x 1600 x 2430 mm Weight 4.5 tons Good condition Credjk S Htxopfx Aqvei

Condition: used, Year of construction: 1980, Technical details: pressure: 400 t Crsdpou N A Uuofx Aqvsi stroke: 40 - 140 mm strokes / minute continous: 32 throat: 400 mm dayligth: min/max: 450/590 mm ram adjustment: 125 mm table-size: 1250x750 mm height over floor: 1130 mm total power requirement: ca. 31,5 kW weight of the machine ca.: 23,0 t machine dimensions LxWxH: 3,7 x 1,7 x 3,9 m dimensions electric cabinet LxWxH: 1,0 x 0,7 x 2,1 m further details: - clamping plate : L x W x H : 1260 x 760 x 100mm - with draw cushion device force 250kN, travel approx. 83mm - control via panel i.D. *

Condition: new, pressure 25 t throat 200 mm stroke 4 - 80 mm table-size 520 x 400 mm no. of strokes 160 Hub/min work capacity during endurance run 1370 Nm force 2740 Einzelhub adjustment of stroke 4 - 80 mm ram adjustment 40 mm ram surface 160 x 160 mm hole in the table 200 x 150 mm clamping plate 500 x 380 x 60 mm hole in the table 80 mm weight of the machine ca. 1,9 t Crsdpfx Aqjb U Hwnevei

Condition: new, pressure 40 t throat 225 mm stroke 8-84 mm Table dimensions 580 x 450 mm ram adjustment 55 mm no. of strokes 130 Hub/min ram surface 185 x 180 mm ram hole 40 H7 mm Crsdpfob U Hwmox Aqvji hole in the table 210 x 170 mm T-slots 22 clamping plate 570 x 450 x 65 mm total power requirement 3,5 kW weight of the machine ca. 2,7 t dimensions of the machine ca. 1,4 x 1,1 x 2,1 m

Condition: new, Year of construction: 2025, Band width: max. 38 mm Feed length: max. 50 mm Band thickness: 0.05...1.02 mm Stroke rate: max. 260 strokes/min at full feed length Codpo Ea U Hefx Aqvjri Feed force: 90 N Available with a mechanical control valve or optionally with an electric valve (24V or 230V). Many other band widths and feed lengths are available.

Condition: used, Pressure: 200 t Length of stroke: 40-180mm Strokes by minute: 32 Up table size: 630x500mm Down table size: 900x800mm Technical characteristics: AIR CLUTCH Power: 15 HP DIMENSIONS: Height: 3000 mms Width: 1000 mms Length: 2750 mms Weight: 14000kgr Codpfo Dvi Usx Aqvjri New electric system

Condition: used, Year of construction: 2007, pressure 200 t throat 510 mm stroke 16 - 160 mm ram - range of adjustment 120 mm table surface area 1500 x 1000 mm table height over floor 900 mm hole in the table 800 x 250 mm Cjdpfx Asvbk Rwoqvori ram surface 1000 x 700 mm tool hole in ram 65 x 110 mm T-slot - width 28 mm number of strokes adjustable 30 - 120 min oil volume Hydraulikaggregat 5 l daylight, max. stroke above - ram adjustment above 600 mm daylight (stroke down, ram adjustment above) 440 mm total power requirement 32,2 kW weight of the machine ca. 24 t dimensions of the machine ca. BxTxH 2,85 x 3,1 x 3,65 m - hydraulic clutch - fixed table - hydraulic overload protection in the ram - hydraulic connecting rod clamping - Motorized ram height adjustment 120 mm with digital display set ram height, rapid and slow speed - fully automatic stroke adjustment, adjustment range 16 - 160 mm - Ram weight compensation - electronic OT correction - Planetary gears - Oil circulation central lubrication - Separate control panel with SIMATIC S7/300 screen control - Press force measuring device - Reversing switch (return) - additional operating mode “set-up-creep speed” - electric stroke counter - electrical preset counter - electrical travel limitation of the connecting rod journal - electronic cam switch - continuously variable drive (frequency controlled) - 2 sockets - Clamping plate - Temperature monitoring main bearing / support bearing / connecting rod bearing - Operating hours counter - Oil cooler - Set of oscillating elements Additional equipment: Electronic roller feed ebu EVX 500 Passage width: 10 - 500 mm Material cross section: max. 1,600 mm² Material thickness: 0.2 - 5.0 mm Number of reels: 2 Roller diameter: 100 mm Intermediate ventilation: up to over 300 l/min Feed length: 1.0 - 9,999.9 mm Feed speed: max. 150 m/min

Condition: used, Year of construction: 2003, operating hours: 2,180 h, * Unladen weight: 7,090 kg * Power: 3.6 kW * Year of manufacture: 2003 Crjdpsumrvbefx Aqvsi * Working height: 15 m * Electric drive -----Internal vehicle number: 10013----Subject to errors and prior sale. WhatsApp support available! If you have questions about the vehicle or for further information, feel free to contact us conveniently via WhatsApp. WhatsApp WhatsApp

Condition: used, Deburring and fine grinding machine for sheet metal / flat material, new The compact machining centre for deburring, slag removal, rust removal, oxide layer removal, edge rounding, fine grinding through to polishing metal surfaces. Due to the fixed working height, this machine can also be optimally integrated into a production line and is suitable for machining large parts. Working width: 1350 mm Maximum part weight: 400 kg Wide belts with abrasive belt unwinding: 2620 mm As standard with vacuum hold system, optional with magnetic hold system By using 2620 mm long abrasive belts, you get a uniformly smooth surface and reduce consumption costs, as these belts have a longer service life. Due to the modular design of the machines, it is possible to offer the optimal configuration for the customer's machining task. The machine structure can accommodate up to 3 internal machining units and an additional external machining unit. The high rigidity of the machine structure and the feed table of this machine, combined with the advanced mechanics and electronics, make this series a universal machining centre for deburring and finishing. Please, contact us for getting more information and pictures on mail(at) or Cjdpfx Aqjm Rpy Rsvsri *