Bottle blowing machine "PET 12,000 bph

KRONES CONTIFORM

Condition: used, Year of construction: 2006, Technical details: x-travel: 800 mm y-travel: 800 mm z-travel: 800 mm turning speeds: 12.000 1/min tool taper: SK 50 control: SIEMENS 840D shopmill tool change unit: 240 fach size of pallet: 630 x 630mm mm spindle: 52 kW / 430Nm total power requirement: 87 kVA weight of the machine ca.: 15 t horizontal machining center, NC-round-table pallet-changer (2 pallets), Bwedpfxopumdco Al Den Internal Coolant Supply 40 bar, prepared for Infrared Touch Probe Renishaw MP 10 without probe, tool-breakage control (mech.), MQL, airblast through spindle, oilmist suction, TRANSMIT funbction, accuracy package, mode 4, glass window right door, incl. FASTEMS FPC 1000 pallet pool for 14 pallets, incl. setting up station, control, and 10 pallets approx. 98.500 h main switch on apprax. 45.500 Spindle hours *

Condition: like new (used), Year of construction: 2008, operating hours: 8,348 h, functionality: fully functional, machine/vehicle number: 2887, pressure: 8.5 bar, power: 2.276 kW (3.09 HP), operating pressure: 8 bar, temperature: 176 °C, total height: 2,950 mm, total length: 5,100 mm, nominal heat output: 2.276 kW (3.09 HP), total width: 2,400 mm, empty load weight: 6,500 kg, Equipment: CE marking, ATTSU RL3000/8 steam generator on sale. The steam generator is in very good conditions and has a low mileage of 8348 operating hours. The generator was used in a factory of pickled vegetables which stopped activity. The boiler has been kept preserved ever since. The boiler includes a fuel oil burner (optional), but can be fired with gas. An inspection on the boiler was performed in June 2025 by a boiler specialist which include thickness measurements and pressure test. The test results were favourable. Boiler Datasheet Bwjdpfxowxd Atj Al Don Manufacturer: ATTSU Model: RL 3000/8 (tube fired) Burner: Fuel oil Serial Number: 2887 Steam Production: 3000 kg/h of saturated steam Rated Pressure: 8.3 bar Test Pressure: 12.5 bar Volume: 3125 liters Year of Manufacture: 2008

Condition: used, Year of construction: 2019, Overview The fill level inspection was built in 2019 by the German manufacturer Krones. The machine is currently not installed. Techn. details: Capacity: 50,000 bph Inspection via gamma ray emitter Krones Checkmat with push-off belt Bedol Hxnispfx Al Dewn

Condition: used, System: used piston diaphragm pump / pump Type: HMD-G-50-500 Flow rate: 40.0 m3/h Bjdpjdkdi Tjfx Al Dewn Pressure: 1,6 MPa

Condition: excellent (used), Year of construction: 2013, GEA Modular Membrane Filtration System up to 6.25 m³/h, in excellent condition and barely used. This equipment was used for just two validation batches, and after that has been in storage. It is currently equipped with spiral-wound nanofiltration membranes but other membrane types can be used for microfiltration (MF), ultrafiltration (UF), etc. The complete original manufacturer documentation is included in digital format, comprising the operating manual, process flow charts, wiring diagrams, certificates, inspection reports, and other relevant technical documentation. The system is designed to process a maximum volume of approximately 100 m³ of product (feed) per day. An average feed flow rate of approximately 4 to 6 m³/h is assumed under the “16/4” or “20/4” operating regime (Explanation: “20/4” corresponds to 20 hours of filtration operation / 4 hours of CIP cleaning). If, at a later stage, the daily processing capacity needs to be increased or the installed membrane surface becomes insufficient due to unforeseeable fouling effects, two empty slots are provided for retrofitting additional membrane housings. The piping and recirculation pump are already prepared for such an expansion. The membrane unit is designed for a semi-automatic cleaning-in-place (CIP) procedure. The system includes the required valves for internal circulation of cleaning solutions, followed by system flushing. Specifications - Feed volume: 400 - 500 m³/week - Feed volume: 80 - 100 m³/day - Feed volume: 4.0 - 6.25 m³/h - Production time: 16 - 20 h/day - Operating temperature: 35 to max. 65 °C Consumption - Power supply (pumps): 3 x 400 V, 50 Hz - Installed power: approx. 65 kW - Electric power consumption: 53.1 kW/h - Compressed air: 6 bar, oil- and water-free - Steam: 6 bar (max.) - Seal water: approx. 75 - 150 l/h - CIP water: approx. 19 m³/h - CIP water per cycle: 6 m³/CIP - Steam consumption per cycle: 100 kg/CIP - CIP chemicals: (e.g., membrane cleaner, acid, alkali, preservative, biocide) Limits - Max. operating temperature: 65 °C - Max. operating pressure: 30 bar - pH range for feed water: Bwsdpfx Alevhctwo Djn - Maximum: pH 10.0 - Minimum: pH 2.0 Cleaning-in-Place (CIP) - Max. temperature: 85 °C - Max. pressure: 10 bar - pH limits (for up to 30 minutes): - Maximum: pH 10.5 - Minimum: pH 2.0

Condition: new, Year of construction: 2021, functionality: fully functional, Stock machine "NEW" – available at short notice! (Subject to prior sale) Control: Fanuc 0i-MF Plus, 10.4" with Manual Guide i & 2 MB NC memory LOOK-AHEAD function, 400 blocks Machine Table: Table size: 950 x 550 mm Load capacity: 800 kg T-slot width: 18 mm Number of T-slots: 3 Distance between T-slots: 150 mm Travel axes: Travel X/Y/Z: 860/550/550 mm Spindle nose to table surface: 150 – 700 mm Linear guides & speeds: Ball linear guides in X/Y axes Roller linear guide in Z axis Rapid traverse X/Y/Z: 40/40/30 m/min Feedrate during milling: 0 – 10,000 mm/min Smallest increment: 0.001 mm Tool magazine (CAM-Type) / changer: Number of magazine pockets: 30 System: random access Max. tool diameter: Ø 75 mm Max. tool diameter with adjacent pockets free: Ø150 mm (40 tools: Ø130 mm) Max. tool length: 300 mm Max. tool weight: 7 kg Spindle: Spindle taper: SK-40 Drive power (30min/cont.): 18.5/11 kW 15,000 rpm direct-drive spindle Spindle oil cooler Coolant, chip, and compressed air management: Coolant system incl. 300 liter tank and pumps External coolant around spindle Chip augers right and left in machine bed Compressed air nozzle at spindle (M32/M33) Compressed air through spindle (M38/M39) Compressed air and coolant gun Other features: Swiveling operator panel Electronic handwheel (wired) Central lubrication oil/air Full enclosure Work light Heat exchanger at control cabinet Auto power-off function Hand tool set Signal lamp Transformer 400 VAC, 50 Hz CE declaration of conformity according to European directives Electrical and pneumatic requirements: Electrical connection: 36 kVA Required pneumatic input pressure: 6 bar Dimensions: Machine size: W2,260 x D2,900 x H2,775 mm Required installation area: W3,160 x D3,000 x H3,000 mm (incl. chip conveyor ejection to the left) Machine weight: approx. 5,400 kg (net) Available special equipment: Spindle: - Direct-driven spindle SK-40, 15,000 rpm - Drive power (30min/cont.): 18.5 / 15 kW, (FANUC motor) Bwjdpfxeifn N Ne Al Dsn Tool magazine / changer: - Drum-type tool magazine with 30 pockets, DIN69871, SK-40 Rotary or additional axes: - Preparation for 4th axis (FANUC controls), incl. wiring and Harting connector, without axis drive Coolant, chip, and compressed air management: - Bed flushing - Through-spindle coolant pump, 20 bar pressure, for direct-driven spindles - Includes cartridge filter - Belt-type chip conveyor including chip cart (chip discharge at front, to the left side of the machine) Measuring and monitoring systems: - RENISHAW OMP-60 probe with infrared transmission system for workpiece measurement, incl. probe holder, repeatability: 1μm - RENISHAW NC4+ tool laser measurement system and tool breakage monitoring in the machine, incl. bracket - Auto-door (side door) - Pneumatic interface for workpiece clamping - Clamping devices as shown With RoboJob Mill Assist 25kg (Year of construction 2025 – NEW) - Full enclosure - Double gripper Available immediately

Condition: excellent (used), Year of construction: 1995, operating hours: 45,000 h, pressure: 10 bar, operating pressure: 10 bar, For sale is a Loos steam boiler with Weishaupt oil burner. Gas burner available upon request. The unit is in very good condition. Model UL-S 5000, year of manufacture 1995. Steam output: 5,000 kg/h. Maximum steam pressure: 10 bar. Delivery available at extra cost. On-site inspection possible. Please contact us if you have any questions. Bedpfxoydq I Sj Al Dswn

Condition: excellent (used), Year of construction: 1999, CNC Lathe MAZAK SQT 200 MS Bedpfx Alex Hgl Hj Djwn Year of manufacture: 1999 Including indicated tools and sub-spindle Control: Mazatrol PC Fusion CNC 640T Technical specifications: Max. swing diameter: 525 mm Max. swing diameter over saddle: 350 mm Max. turning diameter: 300 mm Bar work up to max. diameter: 51 mm Main spindle: Speed range: 35 – 4,000 rpm Main drive power: 15 kW Max. torque: 350 Nm Spindle nose: A2 – 6 inch Spindle bore: 61 mm Spindle positioning C-axis: 0° - 360°/0.001° Second spindle: Speed range: 35 – 5,000 rpm Drive power: 7.5 kW Max. torque: 57 Nm Indexing: 72 positions/5° Tool turret: Number of tool stations: 12 (freely configurable with stationary and driven tools) Turret indexing time – 1st station: approx. 0.2 s Driven tools: Drive power: 3.7 kW Max. torque: 35 Nm Speed range: 25 – 4,500 rpm Travel: Turret travel: X-axis: 190 mm Z-axis: 575 mm B-axis: 585 mm Rapid traverse: X-axis: 30 m/min Z-axis: 30 m/min B-axis: 18 m/min Feed range: X/Z-axis: 0 – 5,000 mm/min C-axis: 1 – 2,000°/min

Condition: used, Year of construction: 2002, turning diameter max. 300 mm turning length max. ca. 550 mm control PC Fusion CNC 640 T Bwedpsxmaguefx Al Djn standard turning dia. 276 mm swing diameter max. 525 mm Distance Spindlenose - turret face 115 - 690 mm turning speed range - main spindle 35 - 4.000 min/-1 power capacity - main spindel 22 kW max. Torque 351 Nm spindle nose A2-6" spindle bore 76 mm max. usable bar diameter 64 mm chucking diameter max. 250 mm C-Axis 360 ° number of toolpositions 12 pos. tool taper VDI 40 Shank diameter 25 mm Drill shank diameter 40 mm turret change time 0,2 / 0,6 sec. Spindle speed - driven tool pos. 25 - 4.500 min -1 power capacity - driven tool pos. 3,7 kW max. Torque 35 Nm Spindle speed range subspindle 35 - 4.000 min/-1 power capacity - Sub spindle 7,5 kW max. Torque 57 Nm chucking diameter max. 150 mm x-axis 190 (185 + 5) mm z-axis 575 (580 + 5) mm Traverses Subspindle B: 585 (580 + 5) mm C-Axis 360 ° rapid traverse X/Z: 30 m/min rapid traverse C: 400 min/-1 rapid traverse B: 18 m/min feed range X/Z: 0 - 5.000 mm/min feed range C: 1 - 2.000 °/min total power requirement 34 kVA weight of the machine ca. 5,9 t dimensions of the machine ca. 5,0 x 3,0 x 2,5 m CNC - Turning- and MillingCenter MAZAK - Super Quick Turn 250 MS - Main- and Subspindle - Tool-Drive - C-Axis

Condition: used, Year of construction: 2021, Overview The filling line was manufactured in 2021 by the German company ALWID. The filling line is new and can fill  chemical products into plastic containers. With the exception of the bottle feeder and Posimat, glass bottles can also be processed. Due to ATEX certification, explosive products can be processed with the line. The equipment comes with a 2-year warranty (in single-shift operation) and all components of the equipment can be purchased separately.  Technical details Capacity: 9000 containers/h (varies according to bottle volume and product).  Container  Max. Diameter: 100mm  Max. Height: 300mm  Control Siemens S7 Single machines  Bottle Hopper | ALWID | POSIMAT-ACCESS-N15  Bottle feeder with hopper 2000 l, in stainless steel, chassis and supports in mild steel painted Positronic control system for optimal adaptation to downstream filler Machine, completely internally wired with attached control cabinet in mild steel, painted Machine according to CE guidelines; i.e. max. noise level of ≤ 80 dB +/- 2 Combined filling and closing machine (block machine) | ALWID | SUPERIOR-16MDM-5SK Fully automatic rotary filler Filling system: mass flowmeter system, type: Endress+Hauser LPG MASS Number of filling stations: 16 filling stations Filling valve diameter: Ø12mm Max. tank dimensions: height: 50-300 mm, Ø: 20-100 mm Fully automatic round capper Number of capping heads: 5 With torque adjustment via slip clutches With fully automatic cap sorting and cap feeding via BONINO disc sorter with elevator With inside drop switch to switch off the machine in case of missing closures Checkweigher | ALWID | OCS-HC-M-2000-1 Applied safety and machinery directives CE compliant Industrial load cell with stainless steel housing based on the principle of electromagnetic force compensation Force shunt free current transfer at the load cell Front protection to reduce interference on the weighing result Stainless steel control cabinet Graphics-capable color TFT touch screen, 10.4 inch, VGA resolution Flexible operability due to tiltable stainless steel operator terminal Freely configurable user interface with simple, intuitive operation Inkjet Printer | Domino | Ax350i  Fast printing of text and multi-line codes at high speeds  Labeler | ALWID | SES-120-III Tandem design Max. Label height: 120mm  Photocell for label scanning 2 x automatic winding station incl. counter pressure plate Mounting device with height adjustment for lateral label dispensers With adjustable side guides - passage width up to 150mm Bwjdpfx Aomfqm Dol Don