Ear-gathering group

HOMAG

Condition: not inspected (used), Year of construction: 2005, functionality: unexamined, workpiece height (max.): 40 mm, edge thickness (max.): 3 mm, feed rate X-axis: 35 m/min, rotational speed (max.): 12,000 rpm, number of slots in tool magazine: 48, TECHNICAL DETAILS Panel height min.: 10 mm Panel height max.: 40 mm Edge thickness min.: 0.4 mm Edge thickness max.: 3 mm Feed speed max.: 35 m/min PROCESSING UNITS Pre-milling unit Automatic engagement 48 tool positions End trimming unit 2 motors Fine trimming unit 1 2 motors Motor power: 0.55 kW Speed: 12,000 rpm Fine trimming unit 2 2 motors Motor power: 0.55 kW Speed: 12,000 rpm Edge scraping unit Glue scraping unit Polishing unit 2 motors Spraying device MACHINE DETAILS Control system: PC 22 EQUIPMENT Pressure applied with rubber belt Panel guides with NC positioning Glue pot for EVA hot-melt adhesive Pre-melter for EVA hot-melt adhesive Laser system (Model: LaserTec) Roller set for edge pressing with 5 pressure rollers Gtsdpoyqybuefx Abyow Units mounted on safety guards CE marking The machine is sold and delivered in its actual and legal condition (“as seen and approved”), based on photo documentation and technical/commercial descriptive documentation. The buyer has the right to inspect the goods prior to collection and assumes responsibility for installation, securing, and use of the machine at the destination. External reference: 5321

Year of construction: 2023, condition: new, Chopping height max. mm. 200 Infeed width mm. 500 Infeed rollers piece 3 Rotor flight circle mm. 600 Chopping length approx. mm. 20-30 output - output 16 - 20 rm/h chipping Chipper blade piece 2 Feed motors kW 2x2,2 Weight approx. net kg 4100 Inlet : horizontal machine base : steel, inert gas welded Rotor : steel, inert gas welded, dyn. balanced. Bearing : Oversized roller bearings. Bearing housing : Steel, flanged housing. Feed rollers : steel, special toothed. Chip outlet : underneath the machine. Godpfxoncd Azj Abyotw Machine grate : (sieve) for secondary crushing of excess lengths. Drive pulley : Matched to main motor N=1500 min-1 Hydraulic system : consisting of: Hydraulic pump, diaphragm accumulator, cylinder, pressure gauge, control valves for lifting of the upper feed roller. Feeding : by 2 gear motors, Make NORD GEAR

Condition: not inspected (used), Year of construction: 2007, functionality: unexamined, working width: 1,935 mm, number of spindles: 40, plate height: 350 mm, working length: 6,200 mm, number of axes: 4, TECHNICAL DETAILS Working area X-axis: 6,200 mm Working area Y-axis: 1,935 mm Maximum panel thickness: 350 mm Number of edge tape magazines: 3 Number of tool positions in tool magazine: 22 (located at the rear of the machine) Gtedpfx Ajyqx U Hebyjw Drilling spindles Spindles for vertical drilling: 28 Spindles for horizontal drilling in X direction: 4 Spindles for horizontal drilling in Y direction: 8 Total number of vertical + horizontal spindles: 40 Milling spindles Number of controlled axes: 4 Motor power: 10.5 kW Automatic tool changer MACHINE DETAILS Total connected load: 31 kW EQUIPMENT Suction cups for securing the workpiece Safety mats at the front Vacuum pump Waste chip conveyor Fixed groove unit for slotting in X direction The machine is sold and delivered in its actual and legal condition (“as seen and approved”) on the basis of photographic documentation and descriptive technical/commercial documents. The buyer has the right to inspect the item prior to collection and assumes responsibility for installation, securing, and operation of the machine at the place of destination. External reference: 8105

Condition: excellent (used), SINGLE SIDE EDGE BANDER (Left) Edges (band in rolls) thickness (Min/Max) mm 0,3 / 3 Edges thickness in strips / lippings (min/max) mm 0,4 / 20 Panels thickness (min/max) mm 8 / 60 NEW (in 2024) Numerical Control EDGETEQ MOD - Power Touch (WoodCommander) Adjustable Feeding speed up to 25 m/min In-feeding system EZ 14 Spraying unit (Anti-sticking liquid) In-feed fence, adjustable by N.C. Pre-milling Unit (vertical joint trimmers) 2 x Kw 3 Glueing Unit (P.U.R. Glue + Quick Melt system) Band Pressure zone, adjustable by N.C. Edge coils supporting unit (with No. 2 reels) Snipping (end-cutting) unit HL 84 (2 x Kw 0,5 ca.) Pneumatic swivelling and adjustment Rough Trimming unit BF 20 (2 x Kw 1,5 ca.) Multi Function Unit (Profile contour Trimming) FK 11 (2 x Kw 0,4 ca.) Gjdpfx Aboyt Izbeyotw Profile edge scraping unit Finish processing unit (Glue scraper + Buffing unit) FA 11 Panels Return System "LIGMATECH" Mod. ZHR 541/L/095 (with Portal bridge and 360° rotating vacuum head)

Condition: used, Year of construction: 2004, SECOND-HAND FINGER JOINTING LINE WEINIG GRECON PROFI JOINT MOD. PJ 150/500 - CE - Wood entry length 150 - 700 - Wood width 40 - 150 mm - Wood thickness 18 - 80 mm - Wood exit length 3,000 - 6,100 Gsdpswry I Eefx Abyetw - Press length 6100mm - Press force 105 kN - Milling unit motor 15Kw - Scoring unit 5.5Kw - Year 2004 CE

Condition: not inspected (used), Year of construction: 2005, functionality: unexamined, power: 19 kW (25.83 HP), travel distance X-axis: 4,175 mm, travel distance Y-axis: 1,730 mm, number of spindles: 20, number of tool stations in tool turret 1: 18, TECHNICAL DETAILS Working area X-axis: 4,175 mm Working area Y-axis: 1,730 mm Gsdpfx Ajyttf Sebystw Number of suction traverses: 8 Number of tool magazine positions: 18 Spindles Number of spindles for vertical drilling: 17 Number of spindles for horizontal drilling in X-direction: 2 Number of spindles for horizontal drilling in Y-direction: 1 Total number of spindles: 20 Milling Unit Number of controlled axes: 4 Motor power: 18.5 kW Automatic tool changer Liquid-cooled MACHINE DETAILS Total installed power: 19 kW Control model: PC85 EQUIPMENT CE marking Front safety guard The machine is sold and delivered in its actual technical and legal condition ('as seen and approved'), based on photographic documentation and technical/commercial documents of a descriptive nature. The buyer has the right to inspect the goods prior to collection and assumes responsibility for installation, securing, and use of the machine at the destination. External reference: 6906

Condition: not inspected (used), Year of construction: 2008, functionality: unexamined, travel distance X-axis: 4,175 mm, travel distance Y-axis: 1,550 mm, workpiece height (max.): 40 mm, number of spindles: 30, travel speed (max.): 80,000 mm/min, TECHNICAL DETAILS Travel range X-axis: 4,175 mm Travel range Y-axis: 1,550 mm Traverse speed X-axis: 80 m/min Traverse speed Y-axis: 80 m/min Traverse speed Z-axis: 30 m/min Maximum workpiece height: 40 mm Number of traverse supports with suction: 8 Spindles Number of spindles for vertical drilling: 20 Number of spindles for horizontal drilling (X-direction): 10 Total number of spindles: 30 Milling unit Number of controlled axes: 4 + Flex5 Motor power: 15 kW Automatic tool changer Liquid-cooled Saw unit Gedpfx Aoyttcwsbyjtw Tool magazine 1 Number of tool positions: 18 Tool magazine 2 Number of tool positions: 10 EQUIPMENT NC positioning of suction units Vacuum pump PowerControl P85 control system WoodWop 5.0 machine programming software The machine is sold and delivered in its actual and legal condition ("as is, where is") based on photographic documentation and technical/commercial descriptions of a descriptive nature. The buyer has the right to inspect the goods prior to collection and assumes responsibility for installation, securing, and operation of the machine at the destination. External reference: 7350

Year of construction: 2013, condition: used, Drying chamber with false ceiling ventilation and frontal trolley loadingfor the production and conditioning of 3 mm oak lamellas, at initial moisture 12 tomax. 15 % / final humidity 7 %used, good conditionmake Mühlböcktype ZSWM2110-1180C - 1.0 l/h at 40° C over 30 % HFyear of construction 2013rated power 7 kW/15Afrequency 50 Hzcontrol voltage 24VDC/230VACprotection class IP54content:the chamber holds- 2 packages in width a 1.10 m - with 0.20 m space between each package- 1 package in height a 1.80 m - with 0.10 m thick underlays and a 0.10 m high free space- 2 packages in length a 2.20 m - plus 0.60 m free spaceThe chamber contains 4 stacking packages and has a total gross volume of 17.4 m²The chamber has a net capacity of 4 m³ of timber - with a timber thickness of 3 mm and a stacking strip thickness of 10 mmand 90 % width utilization with edged ble dimensions of each chamber: Width 2.40 m x height 2.30 m x length 5.00 m- aluminum cassette construction- aluminum frame- dimensionally stable rock wool insulation- aluminum trapezoidal sheet- snow load 100 kg/m²- 2-leaf hinged door- front loading- 2 fans a 3 kW (D=800 mm)- stainless steel/aluminum finned tube heating coil with 50 kW, flow temperature of 80 °C, return temperature 73°C- servo-controlled supply and exhaust air flaps- cold water spraying- chambers work fully automatically- computer control K5Disassembly: Customer locationhandover as viewedwithout guarantee and warranty Gedsvwfhiopfx Abystw

Condition: not inspected (used), Year of construction: 2008, functionality: unexamined, edge thickness (max.): 3 mm, feed rate X-axis: 25 m/min, rotational speed (max.): 12,000 rpm, TECHNICAL DETAILS Minimum edge thickness: 0.3 mm Maximum edge thickness: 3 mm Maximum feed speed: 25 m/min MACHINE DETAILS Edge Processing Unit 1 Unit: End Trimming Model: WK13 Number of motors: 2 Motor power: 0.4 kW Max. speed: 12,000 rpm Edge Processing Unit 2 Unit: Top Milling Number of motors: 2 Motor power: 0.55 kW Max. speed: 12,000 rpm Edge Processing Unit 3 Unit: Multifunction Model: FK13 Number of motors: 2 automatic tool changer with NC positioning Motor power: 0.4 kW Max. speed: 12,000 rpm Edge Processing Unit 4 Unit: Top Mill Model: UF11 Number of motors: 1 Motor power: 4 kW Max. speed: 9,000 rpm Edge Processing Unit 5 Unit: Edge Scraper Model: MN21 with NC positioning Edge Processing Unit 6 Unit: Glue Scraper Model: FA11 Edge Processing Unit 7 Unit: Brush Number of motors: 2 Motor power: 0.25 kW Edge Processing Unit 8 Unit: Brush Number of motors: 2 Motor power: 0.25 kW Total installed power: 35 kW EQUIPMENT Spray unit PowerControl PC22 machine programming software CE marking Gtsdpfx Absytr Hbeyew The machine is sold and delivered in its actual and legal condition ("as seen and approved") based on photographic documentation and descriptive technical/commercial data. The buyer has the right to inspect the goods prior to collection and assumes responsibility for installation, safeguarding, and use of the machine at the destination. External reference: 6216

Condition: ready for operation (used), Year of construction: 2006, Edgebander manufactured in 2006. This HOMAG Optimat KAL 330 features a flexible production layout for furniture parts, accommodating workpiece dimensions from 250 to 3000 mm in length and 120 to 1200 mm in width. It includes a single-sided edge banding machine capable of processing various edge materials up to 20 mm thickness. If you are looking to get high-quality edge processing capabilities, consider the HOMAG Optimat KAL 330 edgebander we have for sale. Contact us for further details. • Line workpiece capacity: • Length 250–3000 mm • Width 120–1200 mm • Thickness 8–60 mm • Edge bander (KAL 330) — base and transport • Continuous machine base; workpiece support with roller bar extendable ~800 mm • Transport chain 80 mm wide with rubber surface; precision guidance, hardened surfaces • Top pressure: driven belt • Technical data: • Feed speed 18–25 m/min Gsdeytf Irspfx Abyetw • Working height 950 mm • Minimum working width: 55 mm at 22 mm thickness; 100 mm at 60 mm thickness (depending on workpiece length) • Workpiece overhang/supernatant 30 mm • Workpiece thickness 12–60 mm • Edge material from strip: 0.4–20 mm (max cross-section 900 mm²) • Edge material from coil: 0.3–3 mm (max cross-section: PVC 135 mm², veneer 100 mm²) • Max coil diameter 830 mm • Pneumatic connection 7–8 bar • Infeed system and controls (integrated with KAL 330) • Flexible workpiece infeed system wz10 for automatic infeed (lengthwise and crosswise); for precisely sized, square parts • Stepless infeed guidance adjustment (axis), speed set at input terminal • Automatic side adjustment of units (workpiece overhang 30–80 mm) for gluing and post-processing • Input terminal; solvent applicator top/bottom • Edge preparation and gluing • Pre-milling unit: 2 motors, each 4 kW, 150 Hz, 9000 rpm; electro-pneumatic control • Stepless vertical axis SF20 for automatic centering to panel thickness • Pre-melting unit with granule storage • Quick-lock system for QA/QE application unit; QA front glue storage for color change • Basic gluing unit A20; magazine height adjustment ±5 mm (manual spindle) • Extended magazine A6/A-E12/A20 for 2 coils (max Ø 830 mm); preheating station for QA/QE • Automatic pressure zone adjustment • Trimming and milling • Trimming unit HL84 with standing trimming stop for sensitive edges • Pneumatic trimming motor adjustment (2 positions: flush/level and with overhang for contour milling) • Pneumatic chamfer/straight changeover; manual side trimming stop adjustment when edge thickness changes • Rough milling unit: 2 motors stacked, each 1.5 kW, 200 Hz, 12,000 rpm; height adjustment via top pressure • Pneumatic 2-position setting: roughing with ~0.2 mm overhang / without overhang • Reserved free space for a fine milling unit • Contour milling unit Servo FK13 automatic: • 2 motors each 0.4 kW, 200 Hz, 12,000 rpm • Servo-controlled movements; automatic 8-fold tool changer • Feed speed max 20 m/min; minimum spacing between workpieces 500 mm • Workpiece thickness 12–60 mm • Automatic FK adjustment for identical radii on different edge thicknesses; auto retract • FK workpiece guidance with additional clamping for min part length 120 mm (single-sided) • Finishing and cleaning • Multi cleaning unit MN21 automatic: • Up to 3 profiles; tracing from top/bottom/side for chamfer and rounding on pre-milled PVC edges • Electropneumatic air nozzles; automatic chamfer/radius changeover; auto retract of upper/lower tool • Height adjustment via top pressure • PVC shavings separator top/bottom

Year of construction: 1990, condition: ready for operation (used), functionality: limited functionality, We are offering this Schiepe stacking machine with 4 side walls, year of manufacture approx. 1990. The unit includes a stick placer with magazines for automated placement of up to 3 intermediate sticks. The machine control system was renewed in 2009 and is fully operational. Mechanically, the machine’s basic functionality is present, though it is recommended to replace several components. Unfortunately, the machine no longer has a nameplate. Gjdpfox Tg Hqox Abyotw Stacking of material up to 6.5 m in length is possible. Machine length is approx. 7 m. The machine was removed from our production line in May 2025 and was operating up to that point. Due to its age, the machine is being sold as a parts donor without any functional guarantee. Manufacturer: Schiepe Model: Stacking Machine 4 Side Walls Year of manufacture: approx. 1990 If you have any questions or require further information, please feel free to send us a message or give us a call.

Condition: used, Year of construction: 2007, operating hours: 39,359 h, functionality: fully functional, machine/vehicle number: 0-201-04-0605, Description of the Main Equipment: Clamping table with matrix aluminium construction Vacuum system prepared for 1000 m³/h nesting technology Power Control control panel with PC85 Main spindle 15 kW with vibration sensor C-axis with aggregate interface Interface for FLEX-5 aggregate Plate-type tool changer with 10 positions Gtedpsyucyzjfx Abysw Drilling unit: 13 spindles – 9 vertical and 2+2 horizontal spindles Software package for office computer WoodWOP Tools software Maximum positioning speed: 80 m/min in X and Y directions (vector speed: X/Y = 113 m/min) / 30 m/min in Z direction

Condition: ready for operation (used), Year of construction: 2009, Edgebander manufactured in 2009. This HOMAG PROFI KAR310/11/A20/S2 features a work piece return system BARBARIC. Consider the opportunity to buy this HOMAG PROFI KAR310/11/A20/S2 edgebander. Contact us for further details. Gjdpfx Abjyhqi Deyotw • Condition: Used Additional equipment • BARBARIC workpiece return system

Condition: new, Semi-automatic drill - Precise lifting frame for accurate drilling results and hard requirements Gedped Rhy Dsfx Abyetw - stepless drilling stroke adjustment with automatic return stroke via limit switch - Two-hand safety control - Horizontal and vertical workpiece clamping via foot switch - Automatic or manual operation - Position-accurate adjustment in the Y-axis - Support table right/left with scale and folding stops We will be happy to provide you with an offer tailored to your requirements.

Year of construction: 2011, condition: ready for operation (used), Main Drive Gtedpfx Asx D Nvgjbysw Number of axis 3 This 3-axis HOMAG WEEKE OPTIMAT BHX 500 was manufactured in 2011. It features a robust CNC processing center with a working area of 2500 mm by 1300 mm, main electrospindle power of 6 KW, and a maximum panel thickness of 80 mm. It includes 84 drilling spindles and dual milling spindles, each offering 6 KW at 18000 rpm. If you are looking to get high-quality CNC capabilities, consider the HOMAG WEEKE OPTIMAT BHX 500 machine we have for sale. Contact us for more information. Application Types CNC Wood Machining