Finger joint system

DIMTER HK 800 K/S/N

Condition: excellent (used), SCM T150 Spindle Moulder Gedpjw Ral Hefx Ahnoud Spindle diameter: 35 mm Total spindle length: 180 mm Electric spindle lift Electric fence movement Electrically adjustable tilt angle -10/45° Variable spindle speed: 3000-4500-6000–7000-10000 rpm Motor power: 5.5 kW DTR technical documentation

Condition: used, No. 3213 Thermal treatment system / vacuum dryer WTT Used, year of construction 2017 Thermal treatment system / thermal chamber for the modification of wood The WTT thermal chamber is a system for the thermal modification of wood. It enables efficient treatment of 2 to 3 batches per day, depending on the thickness and type of wood. The system has a powerful energy and heat transfer system and works with a gas or oil-fired boiler system that uses thermal oil as a heat transfer medium. Technical data: Capacity: 5950 - 9900 m³ of wood per year (for 330 working days) Usable volume: 9 m³ (with 50 mm wood thickness) Stack dimensions: 10500 x 1300 x 1100 mm LWH Minimum board thickness: 10 mm Power connection: 3 x 400 V, 50 Hz + zero + earth, 63 A Specific power consumption: 15.9 kW/m³ Maximum heat output: 2 MW (230 °C - 250 °C thermal oil) Heat consumption: 120 kWh/m³ wood Autoclave length: 11,000 mm Autoclave diameter: 1,800 mm Autoclave material: 10 mm stainless steel duplex EN 4462 Door opens hydraulically, with 1.5 kW drive Working pressure: 0.1 to 15 bar (absolute) Working temperature: 0 °C to 220 °C 200 mm glass wool insulation, clad with 1 mm galvanized sheet steel Main components: 1. autoclave, in which the heat treatment takes place 2. vacuum system that sucks the air out of the autoclave before heat is applied 3. energy center with a 2 MW oil burner 4. 4 MW cooling system with dry coolers 5. nitrogen generator 6. gas cooler system Heating and cooling system: Heat exchanger: 8 units (4 on each side) Material: Stainless steel pipes (seawater resistant) Total floor area: 165 m² Cooling water consumption: 1000 l/batch (not contaminated, only heated) Control and operation: Control system: WTT ExoT (fully automatic) 22” color monitor, IBM computer, printer Sensors: 4 PT100 temperature sensors 2 mechanical thermometers 1 vacuum/pressure transmitter 1 mechanical vacuum/pressure gauge Special equipment: Hydraulic rail bridge for convenient transportation of wooden trolleys Automatic trolley extraction with cable winch (1.5 kW) 2 MW thermal oil boiler (heating) Fuel oil tank (4000 l) with measuring system Insulated 20 foot steel container for heating module Stainless steel safety chimney (300 mm diameter, 6000 mm length) Functional description: 1. filling the autoclave with wood 2. creating a pre-vacuum 3. filling with gas 4. heating 5. modifying 6. cooling 7. pressure equalization 8. creating a post-vacuum / drying 9. pressure equalization 10. emptying Certified EC Pressure Equipment Directive (PED) 97/23/EF Construction EN 13445 Sale on behalf of customer, from location near 5020 Salzburg (Austria), without dismantling, transportation and assembly Dismantling, loading and transportation by us optionally possible Subject to errors in the description and price To avoid possible misunderstandings, an on-site inspection by appointment is possible and recommended Sold as is Technical details, condition description, year of construction and scope of delivery according to manufacturer's brochure or previous owner, without guarantee Subject to prior sale For used machines, any warranty is excluded, the following applies: “purchased as seen” Pictures and videos serve as examples and do not represent the actual scope of delivery Terms of payment: Prices excl. VAT, payment before collection or dispatch Gujdpfev Si Szex Ahnod Terms of delivery: ex location

Condition: excellent (used), LOADER (BRIDGE-FRAME) WITH DOUBLE PICK-UP STATION Guedpfxjfi Tg He Ahned Vacuum system (with its pump) No. 2 Vertical supporting columns of the top supporting beam No. 1 Horizontal top supporting beam (where the carriage slide on) No. 1 Motorized sliding carriage with horizontal metal arms No. 2 Out-side rollers way (on gound) to in-feed pile of panels to the Loader Out-side motorized rollers table (which receives panels from the Loader) Separate electric and command panel Perimetral safety metal grids Working capacity (cycles/min) 16 (ca.) Min/Max panels thickness mm 10 / 50 (ca.) Min dimensions of the panels mm 250 x 320 (ca.) Max dimensions of the panels mm 1300 x 3000 (ca.) Total installed motor power Kw 30

Condition: used, cutting height (max.): 1,200 mm, cutting width (max.): 1,200 mm, cutting length (max.): 6,000 mm, spindle motor power: 5,000 W, fixed bench, pivoting head chain with diagonal vertical movement Gsdpjyzrcmefx Ahnsud automatic cutting waste collection mat

Condition: excellent (used), functionality: fully functional, Söderhamn small log line with Euromill profiles Guedpfswp E E Dsx Ahned Debarker Cambio 45 with infeed and guide work after 2D scanner Söderhamn 447 infeed 240-12 chipper canters Block tilt and infeed 240-12 chipper canter Euromill profiles Board separator with adjustable center Chip conveyor under saw line Hydraulic units and electrical cabinet.

Condition: used, No. 3176 Automatic planer and moulder WEINIG Hydromat 1000 Used, year of construction 2007 6 spindles: bottom-right-left-top-top-bottom Electronic feed 6 - 60 m/min Working width 80 - 150 mm Working height 23 - 65 mm Finished slat widths 4 - 15 mm Max. Max. number of slats 16 pieces Slat lengths 400 - 4000 mm 1st spindle horizontal at the bottom Brake motor 11 kW, 6000 rpm Spindle diameter 45 mm Tool flight circle 125 - 180 mm 2nd spindle vertical right Brake motor 7.5 kW, 6000 rpm Diameter 45 mm Tool flight circle 112 - 250 mm Max. Moulding depth 35 mm Axial adjustment travel 80 mm 3. spindle vertical left 7.5 kW, 6000 rpm Diameter 45 mm Tool flight circle 112 - 250 mm Max. Moulding depth 35 mm Axial adjustment travel 80 mm Pressure shoe in front of the spindle, swiveling away, pneumatic roller contact pressure 4. spindle horizontal top 15 kW, 6000 rpm, diameter 45 mm Tool flight circle 112 - 250 mm Max. Moulding depth 35 mm Axial adjustment path 45 mm Split pressure shoe in front of upper spindle, adjustable and swiveling away, pneumatic 5. horizontal top spindle as saw spindle Brake motor 37 kW, 5000 rpm Diameter 45 mm Axial adjustment travel reduced to 25 mm Tool flight circle 112 - 250 mm Max. Sawing depth 35 mm Axial adjustment path 45 mm Split pressure shoe in front of upper spindle, adjustable and swiveling away, pneumatic 6. horizontal spindle at the bottom as saw spindle Brake motor 30 kW, 5000 rpm Axial adjustment travel reduced to 25 mm Diameter 45 mm Tool flight circle 112 - 250 mm Max. Sawing depth 35 mm Axial adjustment path 45 mm All moulder spindles with high-performance bearings Electronic feed 7.5 kW Adjustment travel of the feed rollers compared to the left-hand spindle, axial 35 mm Shorter roller distance compared to the right-hand spindles Running meter counter, electric, with 2 counters Short infeed table (1.2 m) with 2 driven rollers above the table 1 driven, toothed roller in the table, lateral pressure roller Automatic waxilite pump / lubricant pump Machine with 4-roller extension, pendulum shafts extended to 200 mm 2 driven, toothed rollers in the outfeed table 2 driven, toothed rollers in the machine table Pressure beam before and after upper spindle with mechanical digital display DigiSet (digital double display) for left and top spindles Electrical height adjustment of the upper spindles and the feed Machine already dismantled and stored Sale on behalf of customer, ex location near South Tyrol, without transportation and assembly Subject to errors in the description and price Transportation and loading by us optionally possible To avoid possible misunderstandings, an on-site inspection by appointment is possible and recommended Sold as is Technical details, condition description, year of construction and scope of delivery according to manufacturer's brochure or previous owner, without guarantee Subject to prior sale For used machines, any warranty is excluded, the following applies: “purchased as seen” Images and videos serve as examples and do not represent the actual scope of delivery Gsdpfxeu Agh So Ahnjud Terms of payment: Prices plus VAT, payment before collection or dispatch Terms of delivery: ex location

Condition: good (used), Year of construction: 2003, Automatic hydraulic gluing press Kallesoe Type LV 7821 press is used for gluing wooden elements, e.g. tabletops with maximum dimensions of 7800 mm x 2100 mm, the factor which accelerates gluing is warm water supplied to the press shelf and being in continuous circulation (it can be supplied from CO or heated by heaters mounted on the press) Heating power of the press 72kW Maximum capacity of the press up to 2000 m2 / 7.5h Glue applicator with feeder for Kallesoe press Type KL40 - used to automatically apply glue to each lamella and transfer directly to the press LV7821 Gusdorqzgkepfx Ahnod

Condition: new, Year of construction: 2025, total length: 1,600 mm, total width: 2,200 mm, total height: 2,350 mm, overall weight: 250 kg, type of input current: three-phase, working width: 1,400 mm, Paint booth, paint wall, suction TQN1414 With right or left side discharge. Working dimensions (mm): 1400 (width) x 1400 (height) x 800 (depth) Overall dimensions (mm): 1600 (width) x 2350 (height) x 1250 depth SPECIFICATION: • Fan power 1.5 kW, Guedpfxod S N I Ne Ahned • Efficiency 6,500 m³/h, • 2 x 100% polyester filter • Filtration degree at the level of 99.9%, • Control panel IP 66, • Automatic filter cleaning • Hermetic lighting IP 65. • Paint tank Cabin available immediately (Stock status) SELECT BUMEX SP. Z O.O. Very high quality machines among those offered on the market. Professional advice and service. Warranty. Warranty and post-warranty service. Full technical documentation. 100% satisfaction of our customers. All BUMEX SP. Z O.O. brand products have an EC certificate. We offer our own transport - prices are set each time, for a given offer. We issue VAT invoices. Short lead times! Possibility to order machines in various, personalized configurations and dimensions! Please contact us.

Condition: as good as new (ex-display), Number of spindles 6 St. Working width 250 mm Working height 150 mm Length of the planing table 2500 mm Feed motor 4 kW Feed speed 6-24 m/min. weight 4770 kg Dimensions (L/W/H) 4722x1860x1776 mm Vierseitenhobelmaschine Kuper SWT XL-6 in Fenster-Version mit elektronischer Axial- und Radialverstellung der Spindeln. Schwerer Maschinenständer, verwindungsfrei und schwingungsarm. Anzahl der Spindeln: 6 Arbeitsbreite: 250 mm Arbeitshöhe: 150 mm Abrichttischlänge: 2500 mm Spindeldrehzahl: frequenzgeregelt 4.000 - 8.000 U/min Vorschubgeschwindigkeit: 6-24 m/min Gedpfx Ahevnv Ubeneud Ausführliche Beschreibung finden Sie in nebenstehender PDF-Datei! (Technische Angaben laut Hersteller - ohne Gewähr!)

Year of construction: 1999, condition: good (used), Built in: 1999 Capacity (A4 stacks packaged): max 20 - 24 Pakete/min Capacity ( A4 stacks loose): max 16 - 20 Pakete/min Pallet height (incl. pallet): max 1.600 mm Pallet size : max 1.200 - 1.200 mm Size: max 420 x 307 x 320 mm Size: 148 x 110 x 50 mm Equipment: • infeed and buffer section • turntable • infeed table • automatic palletizer • roller track for full pallets • intermediate cardboard slip sheet hopper Guodpodym Srjfx Ahnsd • pallet dispenser