Injection press

BOSSI V 1250

Condition: new, Year of construction: 2025, functionality: fully functional, The CNC BAYKAL Hybrid Press Brakes combines all the benefits of both hydraulic and all-electric press brake systems into one. If you’re looking for press brakes that are fast, accurate, and energy-efficient, BAYKAL is the way to go. Kedpfx Aaerq D Nij Iodn The CNC BAYKAL Hybrid Press Brakes can significantly save energy, save fuel, improve bending efficiency, reduce the risk of oil leakage, reduce installation costs, extend the service life of consumables, improve bending accuracy, reduce noise, and improve the working environment. The CNC BAYKAL hybrid press brakes system are designed with an individual electro-hydraulic servo drive system and servo pumps to control the for each of the left and right cylinders. The servo motor controls the output flow of the oil pump according to the program setting, and then controls the movement speed and position positioning of the slider, and there is no throttling phenomenon in the whole process. Therefore, all the energy output by the oil pump is supplied to the left-right oil cylinder. This control method does not have any energy loss, and the energy-saving effect is very prominent. With this system the hydraulics run on demand when the foot pedal is activated, rather than having a pump running continuously. This results in lower energy usage than a standard hydraulic machine as well as faster cycle times and extremely high accuracy. The flow and pressure of Y1 and Y2 oil cylinders are respectively controlled by two sets of servo bidirectional pump systems, and the oil in the upper chamber of the oil cylinder is directly pumped into the lower chamber of the oil cylinder through the oil pump to realize the lifting of the beam. The reverse rotation of the oil pump pumps the oil in the lower chamber of the oil cylinder directly into the lower chamber of the oil cylinder to realize the pressing and bending of the upper die. Applicable between from 100 Tons to 1250 Tons, the synchronization of the left and right of the upper beam of the CNC BAYKAL hybrid press brakes is controlled separately by two sets of servo bidirectional pumps.

Condition: new, Year of construction: 2025, Delivery ex works Turkey Bending length (A): 3050 mm Press force: 170 tons Sheet thickness 42kgf / mm: 8 mm Sheet thickness 72kgf / mm: 4 mm Upper tool: 1260 Top Tool 85 ° Lower tool: 50, 35, 22, 16 Distance between columns (B): 2550 mm Forward speed: 130 mm / s Working speed: 8 mm / s Retraction speed: 120 mm / s Crowning: manual (CNC-motorized available for an extra charge) X-axis travel: 750 mm X-axis speed: 250 mm / s Backgauge fingers: 2 pieces Front support arms: 2 pieces Oil tank capacity: 180 liters Main motor power: 11 kW Stroke length (C): 265 mm Installation height (D): 450 mm Projection stand (E): 410 mm Table height (F): 870 mm Table width (G): 170 mm Length (L): 4200 mm Height (H): 2800 mm Width (W): 2200 mm Weight: approx. 7500 kg Cybelec Cybtouch 12 2D Graphic CNC control 3 axes (Y1, Y2, X) expandable with optional R+Z-Axis Eurostamp 2067 lower tool (V: 50, 35, 22, 16) Eurostamp 1260 upper tool 85 ° Narrow table All-steel welded construction Promecam quick clamping system CNC-controlled motorized backgauge (X: 750 mm) Adjustable backgauge fingers Inch and metric system can be selected Ground and chrome-plated cylinders Swiveling control panel Foot control with anti-panic stop & emergency shutdown Lateral protective grille (secured with limit switch) Light curtain on the back of the machine (900 mm) DSP laser finger protection system at the front (CE) BOSCH / REXROTH or HOERBIGER / HAWE hydraulic system BOSCH / REXROTH or ECKERLE hydraulic pump Slidable front support arms (2 pieces) Electronics unit from: SIEMENS, SCHNEIDER, DELTA, ABB, OMRON 380 V 50 Hz Painting: RAL 7035, RAL 5015 Kdedpogu N Alsfx Aa Ijn Optional special accessories available at an additional cost: -CNC-controlled R-axis (250 mm) -CNC motorized crowning -Servo driven motors backgauge system for X + R axis (Mitsubishi) -Painting in special colors on customer request Documentation in German or English CE conformity

Condition: like new (used), Year of construction: 2006, operating hours: 33,107 h, functionality: fully functional, Top machine from cleanroom production (pharmaceutical sector) - Equipped with 820 mm rotary table - Including GEKU Robot SR 500 ST (x=600, y=1400, z=2500 mm) - Only 33,107 operating hours - Safety enclosure / protective cage - Horizontal conveyor belt - Hardly any paint damage / almost as new in appearance - Fully operational The machine can be inspected under power by prior arrangement. Technical Specifications Manufacturer: Engel Model: V 330H/80V/130 Combi 2-Color with rotary table Serial number: 162036 Year of manufacture: 2006 Operating hours: 33,107 h Dimensions L/W/H: see drawing Weight: 10,600 kg Functionality: fully operational Condition: excellent Special features Control system: CC 200 Screw diameter: 25 / 22 mm Shot weight: 72 / 35 g Injection pressure: 2391 / 2066 bar Injection volume: 79 / 38 cm³ Clamping force: 1300 kN / 130 tons Tie bar spacing: tie-bar-less Ejector stroke / force: 61 kN / 100 mm Clamping unit: hydraulic Motor power: to be provided Heating capacity: to be provided Total power: to be provided The machine is immediately available from our warehouse in Hannover, Germany, and has been tested. Extras 2-component / 2-color machine Rotary table (820 mm diameter) Geku Robot SR 500 ST Safety enclosure / protective cage CC 200 control, German and English languages GEKU Robot Details SR 500 ST Control: Simotion X axis: 600 mm Y axis: 1400 mm (vertical) Z axis: 2500 mm (horizontal) A flip axis: SWM 45 C axis: Servo Gripper: SWS16 B axis: not available Warranty Warranty up to initial commissioning Kodeub Umqjpfx Aa Iedn Loading/Shipping Free loading onto buyer's truck or free delivery against freight reimbursement from our warehouse in Hannover, Germany Financing – on request – leasing option Price on request

Condition: used, Year of construction: 2006, operating hours: 60,000 h, Injection molding machine Krauss Maffei 50-180 CX Kdodpfx Aaov Tmzpj Ien Year 2006 screw di 30

Condition: excellent (used), Year of construction: 2008, Demag System 800/1120–9500 Injection Moulding Machine Year of manufacture: 2008 Additional equipment: Injection moulding machine equipped with robot Clamping unit Parameter Value Clamping force 8,000 kN Platen dimensions (W × H) 1,620 × 1,500 mm Tie bar spacing (W × H) 1,120 × 1,000 mm Min. / Max. mould height 500 – 1,050 mm Kedpfx Aaewy U E Uo Ijdn Maximum distance between platens 2,080 mm Mould opening stroke 1,030 mm Ejector stroke 350 mm Ejector force 139 kN Maximum mould weight 7,200 kg Injection unit Parameter Value Screw diameter 130 mm Injection volume 7,300 cm³ Shot weight (for PS) 6,640 g Injection pressure 1,300 bar L/D ratio (screw length/diameter) 20 Electrical-hydraulic equipment Parameter Value Pump motor power 110 kW Heater power 79 kW Oil tank capacity 1,300 litres Dimensions and weight Parameter Value Machine dimensions (L × W × H) 12.3 m × 2.7 m × 2.7 m Total weight 33,500 kg (main unit) / 9,700 kg (auxiliary equipment)

Condition: used, Hydraulic Plate Shear LVD Type HST-C 31 / 6 Kdodpotvb Iujfx Aa Ien Machine No. 21348 Year of manufacture: 1994 Cutting length: 3,100 mm Cutting thickness: 6.35 mm Backgauge: 770 mm Working height: 950 mm Hydraulic sheet hold-downs: 17 units Hydraulic tank capacity: 150 liters Motor power: 7.5 kW Power connection: 400 Volt, 50 Hz, 9.5 kW, 19 Amp. - Motorized backgauge with digital actual position display ELGO - Backgauge adjustment via push button – rapid in both directions and fine adjustment by jogging in the minus direction only - Sheet lifting device below the backgauge with pneumatic lifting cylinder - Continuously adjustable blade gap from 0.1 mm via handwheel with analog display - Cutting angle adjustment in 5 steps from 1.5° to 3.5°, electrically pre-selectable - Left side angle stop 1,500 mm - 2 table extensions as sheet supports - Electric foot switch - Comprehensive operating manual Space requirements without front table extension (L x W x H): 4,150 x 1,850 x 1,900 mm Space requirements with front table extension (L x W x H): 4,150 x 2,850 x 1,900 mm Weight: 5.5 tons Good condition Very good cutting results, including with thin sheet metal

Condition: ready for operation (used), Year of construction: 2001, clamping force: 500 kN, injection pressure: 2.2 bar, For sale is an injection molding machine of the brand Arburg and the type 320 S 500-150 The machine is in working order Technical data - Clamping force: 500 kN - Distance between the tie bars: 320 mm x 320 mm - Mold thickness: 225-350 mm - Clamping platen dimensions: 445 mm x 445 mm - Opening of the clamping platen: max. 550 mm - Screw diameter: 30 mm - Injection pressure: 2 200 bar - Weight: 2 250 kg On request, for an additional charge, dismantling, loading & transport can be organized for you throughout Europe Prices plus VAT Viewing possible by appointment. Contact us, our team will be happy to help you. Trade-in or exchange possible! Ksdpfjqmn Egjx Aa Iedn Machines purchase / sale BUYING / SELLING PRODUCTION & METALWORKING MACHINES AND MUCH MORE. Do you need a high-quality but inexpensive metalworking machine for your production? Or do you want to sell yours? For further information or contact options, please visit our website

Condition: ready for operation (used), Year of construction: 2023, clamping force: 2,500 kN, screw diameter: 55 mm, overall weight: 8,400 kg, Hydraulic injection moulding machine manufactured in 2023. This HAITIAN MA 2500 III features a clamping force of 250 tons and a platen size of 850 x 850 mm. The machine includes an impressive injection pressure of 1850 bar and a screw diameter of 55 mm. If you are looking to get high-quality injection moulding capabilities, consider the HAITIAN MA 2500 III machine we have for sale. Contact us for further details regarding this machine. • Clamping unit • Opening force: 165 kN • Platen size: 850 x 850 mm • Opening stroke: 540 mm • Tie bar distance: 580 x 580 mm • Max mould height: 580 mm • Min mould height: 220 mm • Ejector stroke: 150 mm • Ejector force: 62 kN • Min mould dimensions: 410 x 410 mm • Injection unit • Euromap classification: 1000 • L/D ratio: 20 • Shot volume: 570 cm³ • Effective injection volume: 519 g • Injection rate: 281 g/s • Plasticizing capacity: 47.7 g/s • Injection pressure: 1850 bar • Screw speed: 180 rpm • Screw stroke: 240 mm • Carriage force: 99 kN • Pump motor power: 37 kW • Heater power: 21.45 kW • Oil tank capacity: 340 L • Dimensions • Machine size: 6.19 x 1.60 x 2.42 m • Control • Controller: KEBA 2985 – CP053 • Features: • 15” colour touchscreen • Euromap 67 robot interface • USB memory • 200 mould memory • Cycle history • Alarm tower • RFID login/password • Multilanguage interface • Process graphs • Maintenance pages • Metric / imperial selectable • Included options / extras (machine-integrated) • Bimetallic screw + barrel • Masterbatch dosing interface • Hydraulic radial extraction • Festo air blow system • 12-zone PSG central lubrication • 4-way flowmeter • Robot interface • Included screw H 3 zones • CE certified work cell Kdsdpfx Aoy N Sqmea Isn Additional equipment • Robot included: HILECTRO V-1300ID Cartesian Robot (2023) • Type: 3-axis servo Cartesian robot • Suitable for: 380T to 530T presses • Travels: X 2000 mm / Y 880 mm / Z 1300 mm • Max extractable weight: 12 kg • Power: 400 VAC / 50-60 Hz • Precision: 0.1 mm • Robot weight: 530 kg • Included: Touchscreen controller, USB programs, pneumatic gripper, vacuum cups, conveyor ready • Peripherals included: FORMAX E3 Monofase Hopper Loader (2 units) • Hopper capacity: 3.0 L • Power: 1150 W • Inlet diameter: 40 mm • Capacity: 70 kg/h • Voltage: 230 V • Weight: 13 kg each

Condition: ready for operation (used), Year of construction: 2020, operating hours: 8,000 h, clamping force: 500 kN, screw diameter: 25 mm, injection weight: 46 g, total height: 1,779 mm, overall weight: 4,200 kg, This SUMITOMO SHI DEMAG Intelect 2 50/370-110 was manufactured in 2020. It features a fully electric direct-drive system, NC5+ control for enhanced energy efficiency, and precise injection dynamics. Includes a granule dryer, industrial robot, conveyor belt, and temperature units. Ideal for high-quality injection moulding processes. Contact us for more information about this machine. Additional equipment • Granule Dryer • Handling System • Conveyor Belt - 1400 mm x 400 mm • Precision Scale • Temperature Units - 2x HB‑Therm Machine Benefits Technical Machine Benefits Kdedpfx Ajx D Eccea Ijn • Exceptional energy efficiency • Enhanced platen rigidity and mold safety • Fully electric direct-drive system • Ultra-precise direct-drive motors with 0. 1 ms response time • Displacement: 52 cm³ • Spray pressure: 2180 bar • Tool clamping platens: 520 x 570 mm Extra Information Control Unit Advanced control system with NC5+ Automatic mold height and clamping force adjustment Energy-saving routines Dimensions Machine Depth 4308 mm

Condition: good (used), Year of construction: 2004, On request and for an additional charge, loading and transport (throughout Europe) can be arranged. All prices include VAT. Viewing is possible by appointment. Please contact us—our team will be happy to assist you. Trade-in or exchange is possible! Kdsdpfx Aoxirqqoa Isn Phone: Mobile: (also via WhatsApp) Web: Machinery Purchase / Sale PURCHASE / SALE OF PRODUCTION & METALWORKING MACHINES AND MORE. Do you need a high-quality yet affordable metalworking machine for your production? Or are you looking to sell yours? For further information or contact options, please visit our website.