Pillar drill

ALZMETALL AB 5 HST

Year of construction: 1972, condition: used, machine/vehicle number: 51512/72, pression: 75 t throat: 300 mm table size: 620 x 800 mm clearance hole in the die: 225 x 325 mm table adjustment: 175 mm tappet area: 180 x 475 mm tappet adjustment: 80 mm stroke adjustment: 16 - 140 mm number of strokes: 90 /min engine: 380 V, 3 kW space needed: 1700 x 1200 x 2500 mm Duodpfx Asb Tdquecxsp weight: 3,3 t

Condition: used, Year of construction: 1994, functionality: fully functional, throat depth: 1,250 mm, Radial drilling machine Fab. Breda type. R 55-1250 Year of manufacture 1994 Technical details Make: BREDA Type: R 55-1250 Throat: 1250 mm Drilling capacity in steel: 55 mm Drilling capacity in cast iron: 70 mm Tapping capacity in steel: M 50 Tapping capacity in cast iron: M 65 Drill spindle mount: MT 5 Throat: 1250 mm Cross travel of headstock: 930 mm Minimum/largest distance from base plate: 5360 – 1375 mm Vertical travel of the boom: 705 mm Spindle stroke: 310 mm Number of spindle speeds: 12 Spindle speeds: 30 – 1200 rpm Number of feeds: 8 Feeds: 0.06 – 1.0 mm/rev Base plate 2070 x 910 mm Clamping area base plate 1325 x 910 mm Motor power 4.4 kW - 380 volts Dimensions (L x W x H) 2.1 x 1.0 x 2.5 m Weight 3 t Accessories Drilling table 750 x 600 x 550 mm Cooling Hydraulic clamping Duedpfx Aov Rpf Sscxop All information is subject to change. A demonstration is available at any time in our showroom.

Condition: used, Universal Milling Machine DECKEL FP1 Travel X: 300 mm Travel Y: 150 mm Dujdpfx Asxxpp Njcxop Travel Z: 300 mm Horizontal + vertical spindle Cone SA40 DECKEL Spindle speed: from 40 to 2000 RPM Table size: 600 x 210 mm Horizontally tiltable head Straight table Spindle motor: 2 speeds Motor: 1,3 kW Feeds: X - Z auto / Y manual Voltage: 380 V Width: 1200 mm Depth with electrical panel: 1200 mm Height:1600 mm Weight: approx 900 kg

Condition: used, Year of construction: 1995, Technical details: sheet width: 3000 mm plate thickness: 12 mm distance between columns: 3500 mm control: Cybelec DNC 10 G back gauge: 1200 motorisch mm cutting angle: 1,2 - 2,73 ° cutting gap adjustment: ja mm cutting capacity : 66.000 daN daN Knife length: 3100 mm down holder: 17 Stück interface: RS232 Table dimensions: 3200 x 600 mm total connected load: 22 kW weight of the machine ca.: 11,0 + (1,0 to Anbauteile+Zubehör) t space requirements approx. LxWxH: ca. 4,5 x 2,6 x 2,1 m transport dimensions LxWxH: ca. 5,0 x 2,25 x 2,2 m The guillotine shear was put into operation for the first time in 1998. The DNC 10 G control unit was specially designed for guillotine shears. It has a numerical axis for controlling the backgauge and automatically calculates and regulates the cutting gap, the cutting angle and the cutting depth, taking into account the material to be cut. (Data from the manufacturer) Table with side stopL:930 x W:105 x H:42 mm 2 table extensions L:1600 x W:100 x 83 mm Angle fence (attached to table extension) Operation via control panel with swivel arm and foot control Duodpsvc Amtofx Acxep Equipment: Drain with rollers for clippings 2x protective grid *

Condition: excellent (used), Here we offer a used Datona mobile sandblasting unit. Datona mobile sandblasting unit DUO - 74 liters SKU DT-55212 Advantages and disadvantages: 2.5 m long hose for a long reach Easy to switch between blasting agents thanks to the mixing valve When using soda, the surface of the workpiece is not damaged Description: Dusdpfsqcuvwsx Acxep This mobile sandblasting machine is used for removing paint and rust. Thanks to the two boilers, you can choose from two different blasting media. The mobile sandblasting unit works with a pressure of 4 to 8 bar and requires a compressor with a suction capacity of at least 350 l/min. Double boiler: If blasting with soda or calcium carbonate does not achieve the desired result, simply try a different blasting agent. For a more effective effect, it is also possible to use both blasting agents at the same time. With the sandblaster, you have a practical machine in your home. With the help of the special mixing valve, you can use soda to easily and gently remove paint from steel, stainless steel, chrome, aluminum or polyester. A major advantage of blasting with fine soda is that the surface of the object to be of the object to be blasted is not damaged. You don't even have to remove rubber seals, chrome parts or glass. This saves a lot of time! The mobile sandblasting unit can be used both in the workshop as well as on site. Attention: The one boiler is only suitable for soda and calcium carbonate!!! ✓ Duo sandblasting unit ✓ 74 liter boiler capacity ✓ Air consumption is around 350 l/min Technical data: SKU DT-55212 Weight 33 kg Suitable blasting material Aluminum silicate Dato-Blast calcium carbonate soda Blasting cabinet connection 1/4" Max. Pressure 2 - 6 bar Minimum air consumption 350 l/min Min. compressor tank capacity 100 liters Type: DT-55212 Condition: gebraucht / used Scope of delivery: (see picture) (Changes and errors in the technical data, specifications are reserved!) We will be happy to answer any further questions you may have on the phone.

Condition: used, machine/vehicle number: 697, mileage: 32,242 km, power: 132 kW (179.47 HP), first registration: 01/1995, fuel type: diesel, empty load weight: 9,500 kg, maximum load weight: 2,300 kg, overall weight: 11,800 kg, tire size: 9r22,5, axle configuration: 4x4, brakes: retarder, color: green, driver cabin: day cab, gearing type: mechanical, suspension: steel, operation weight: 18,200 kg, Equipment: ABS, all wheel drive, compressor, crane, differential lock, hydraulics, retarder, trailer coupling, TUV is made NEW truck registration , The Steyr in a dreamlike good condition directly from the authority (Swiss Army) Super maintained and checkbook maintained, see photo, the body is in a super good condition , The 12S18 is equipped with: All-wheel drive , differential lock rear , 2 seat patches front a 3. Load capacity at 3.6 meters = 2 tons and at 5.4 meters = 1.36 tons, - MKG crane type HLK 73a1, this also has a Rotzler cable winch, type HK 022 with 10 mm steel cable to lift or lower loads from or into the shaft at the crane tip, - The crane nozzles still have a manual extension so as not to hinder the off-road capability. - Tire size 9R22.5, transmission with 6 gears plus off-road reduction , has a speed limiter , empty weight 9500 kg , total weight is 11800 kg , cubic capacity 6592cm? , , 24Volt power supply , The Steyr not only has Tuv when handed over, but also drives reliably :-) - The Steyr is also ideal as a hobby vehicle but does not shy away from daily work. - All my vehicles can be seen on my homepage. - You are now rushing back and forth from Flensburg to Berchtesgaden to look at the different cars, but here you will find over 150 vehicles of the following types: - Hanomag AL 28, Magirus Deutz, MAN, Steyr, Dodge WC, Saurer, Unimog, GMC 6x6, Steyr-Puch, Iltis, Willys, G-Model, Mowag, DB, etc., and all with TUV. - even with TUV. - There are also an unimaginable number of spare parts and accessories. - Why would you settle for anything less? - Give us a call on 0049 (0)2248 Greetings, Philipp Dujdpfxsqx Szns Acxsp

Condition: used, Year of construction: 1995, Technical details: bore capacity in steel (diameter): 32 mm throat: 293 mm bore stroke: 120 mm bore capacity in St 60 - full boring: 40 mm bore capacity in cast iron: Ø 38 mm spindle taper MT: MK 3 spindle throat: 293 mm spindle speed:: 160 - 2250 / seples U/min feed: 0,10 - 0,20 / manuell+automatisch mm/U Distance spindle/table max.: 55 - 642 mm table clamping surface:: 300 x 300 mm drill table adjustment: ja mm column diameter: 115 mm distance spindle center to floor plate:: 1207 mm total power requirement: 1,9 kW weight of the machine ca.: 280 kg Duedpox U Dkcefx Acxop dimension machine xH: 0,7 x 1,0 x 1,9 m

Condition: used, mileage: 52,840 km, power: 90 kW (122.37 HP), first registration: 10/1996, fuel type: diesel, empty load weight: 3,135 kg, maximum load weight: 2,855 kg, overall weight: 5,990 kg, tire size: 215/75R17,5, axle configuration: 4x2, wheelbase: 3,700 mm, brakes: engine braking, color: white, driver cabin: sleeper cab, gearing type: mechanical, emission class: euro2, suspension: steel, number of seats: 3, loading space length: 4,000 mm, loading space width: 2,200 mm, loading space height: 350 mm, Equipment: cabin, trailer coupling, Vehicle location: Bovenden, Kz. house, double bench seat, rear window, heated mirrors, switch 5, constant throttle, power take-off, leaf suspension, trailer ball head, U-protection, aluminum side bumpers, pendulum flaps Wheelbase: 3700 mm Body: Meiller 3-sided tipper body HA H2 5.6t crown wheel 312, trailer socket 7-pin, engine OM602 DE29LA 90kw, power take-off countershaft DB (2c), springs VA and HA reinforced. ACCESSORY INFORMATION WITHOUT WARRANTY, subject to alterations, prior sale and errors excepted! Duedjvhkfzspfx Acxep - .

Condition: good (used), Lid folding machine, folding machine, folding machine, lid folding machine, can folding machine, can folding machine -Lid seaming machine for sheet metal buckets Dodpfx Acsb A H R Eexjup -The machine creates the fold for the lid -Dimensions: 1000/1200/H1150 mm -Weight: approx. 800 kg

Condition: excellent (used), Year of construction: 2008, functionality: fully functional, Ibarmia AZ-34 Pillar Drilling Machine (2008) Manufacturer: Ibarmia Model: AZ-34 Pillar Drilling Machine Year of manufacture: 2008 Condition: Used, very good, newly serviced Drilling capacity in steel: 34 mm Thread cutting capacity in steel ST 60: M 27 Speed range: 100-2000 rpm Speed control: Potentiometer Speed display: Digital Tool holder: MT 4 Quill stroke: 150 mm Column diameter: 125 mm Feed: 0.1 / 0.2 / 0.3 mm/rev Type of feed: Mechanical Arm length: 300 mm Table size: 400 x 480 mm Drive power: 2.2 kW Electrical connection: 400/50 V/Hz Weight: 360 kg Infinitely variable speed control with digital readout Electronically adjustable from 100 – 2,000 rpm Machine lamp Coolant system integrated in the machine base Machined baseplate with 2 T-slots Integrated tool ejector Chip guard with microswitch Dedpfxex Ivzyo Acxsup Automatic reverse rotation for thread cutting 3 automatic drilling feeds Operating manual included Dimensions/Weight: 2350 x 610 x 1100 mm (LxWxH)