Horizontal milling machine

WMW AUERBACH F 315

Condition: as good as new (ex-display), Year of construction: 2023, operating hours: 31 h, 3D Coordinate CNC measuring device Profitech Innometrik Advanced in gantry design (demo unit at a special price) Open Cable Special features of the gantry design: Gantry design with a low center of gravity, wide bearing separation and optimum stiffness to mass ratio. The granite guideways ensure a uniform thermal, dimensional, torsional and geometric stability of the machine. 24 air bearings for smooth movement of the three axes. High dynamics for better performance, the machine can achieve high accelerations like comparable medium and large CMMs. Thermally compatible materials and components minimize the influence of ambient temperature fluctuations on measurement results, Air filter and regulator. Z-axis pneumatic counterweight system. Granit table with thread inserts of size M10. Passive vibration isolation pads Technical specifications Measurement paths: X: 500mm Y: 600mm Z: 400mm Max workpiece weight: 250kg Weight of the machine: 850kg Dimensions over everything: 1290x1160x2350mm Accuracy according to DIN EN ISO 10360-2 or ISO 10360-4: Volumetric probing deviation: MPEP = 2.2μm Volumetric length measurement deviation: MPEE = 2.2+ L / 350 (μm) Environmental conditions: Room temperature standard: 18-22 ° C Operating temperature 10-35 ° C Air Supply: Cjdpfx Afodyah Sjnjpu Minimum air pressure: 6bar Air consumption: 90NI / min Also configurable as a complete package with touch probe, software commissioning and training. (Annual maintenance & calibration can also be offered)

Condition: used, Year of construction: 1982, grinding length:500 mm grinding width:225 mm workpiece height:400 mm total power requirement:5,5 kW Cpjdpfx Afecxxtmsneu weight of the machine ca.:3,4 t NC81 NC-control, table belt drive 100-25000 mm/min., automatic feed, electronic dressing unit 020 NC-K with RPM-compensation, coolant pump, emergency cut-off

Condition: ready for operation (used), Year of construction: 2005, operating hours: 52,455 h, functionality: fully functional, machine/vehicle number: 2501-0154, turning length: 600 mm, turning diameter over cross slide: 140 mm, turning diameter: 300 mm, spindle motor power: 25,000 W, spindle speed (min.): 5,000 rpm, spindle speed (max.): 5,000 rpm, travel distance Z-axis: 900 mm, rapid traverse X-axis: 3 m/min, rapid traverse Y-axis: 3 m/min, rapid traverse Z-axis: 3 m/min, rotational speed (max.): 4,000 rpm, rotational speed (min.): 4,000 rpm, torque: 239 Nm, bar passage: 80 mm, feed rate X-axis: 165 m/min, feed rate Y-axis: 165 m/min, feed rate Z-axis: 220 m/min, overall weight: 10,500 kg, Equipment: documentation/manual, Machine is still in use and can be seen working at VOVU Machining in Uden. In total there are 6 identical machines here. Fanuc 310is controller Cpodjur Hfzopfx Afnju

Year of construction: 1969, condition: ready for operation (used), Max. grinding depth: 80mm, distance spindle table: 145mm, spindle bore: 28mm, connected load: 7kW, length: 2100mm, width: 1400mm, height: 950mm, weight: 1.6t, with documentation, an inspection is possible. Cpodoqzkdmspfx Afnsu

Condition: good (used), Year of construction: 1989, operating hours: 64,136 h, Centre height: 350 mm Turning length: 1000 mm Max. swing diameter over bed cover: 600 mm Max. swing diameter over cross slide: 360 mm Spindle bore: 107 mm Speed range: 16 – 3150 rpm Feed range longitudinal & face: 0.5 – 5000 mm/min Rapid traverse longitudinal & face: 9 m/min Main drive: 30 kW Cpjdjvr Eh Ejpfx Afnsu Dimensions of machine with chip conveyor (L x W x H): 5400 x 2200 x 2000 mm Weight: 6400 kg Accessories / Special features: • CNC control GILDEMEISTER EPL 2 with TFT display General description: CNC manual input control system with program entry via function and numeric keypad. All information is entered in dialogue with the screen. Integrated menu technology with plain text display of all functions. Operator keypad, display, and electronic handwheel located within a separate chip guard housing. The EPL control offers the following capabilities: • Direct interactive program entry and editing by the operator through the EPL control without manual technological preparation • NC programs in ISO/EIA format can be entered, output, or manually keyed in via the RS 232 serial interface Machining cycles: • Removal cycles for longitudinal, facing, and contour turning, including with allowance • Thread cutting • Undercuts as per DIN 509-Form E and F and DIN 76; grind stock programmable • Axial and radial grooves as per DIN 471 and 472, including bottom finishing • 90° radii and 45° chamfers • Automatic cutter radius compensation for cycles, undercut, groove, radius, chamfer Programming: • Block-orientated, metric/inch, diameter for absolute entry, radius for incremental entry • Full circle programming, subroutine technology, hide levels for program sections, zero point offset, mode selection via menu Program entry and output: • Interactive via guided menu or direct in dialogue • Hydraulic 3-jaw chuck Ø 315 mm with through spindle bore Ø 80 mm • Hinged chip conveyor • 12-position tool turret VDI 40, 6 standard stations + 6 driven tool stations • Coolant system • RS 232 interface • Electronic handwheel • Electric foot switch for 3-jaw chuck and tailstock quill • Lighting • 12 various standard toolholders (to be finalized on site) Overhauled servo drive for main spindle, 06/2025 Siegfried Volz Werkzeugmaschinen Rüschebrinkstr. 151-153 DE - 44143 Dortmund - Wambel

Condition: good (used), Year of construction: 2000, Parts shown by hand not come. Tool cabinet and cutting tools not come. Only tool holders will come. Cpedpfx Afjx Atyaensu

Condition: excellent (used), Year of construction: 2000, Siemens control unit Bar passage 32 mm 2 x 12-position turrets with driven tools Main / counter spindle Codpfx Afewh U Edenjpu Y-axis turret top Parts lifting device Chip conveyor IRCO bar loading magazine

Condition: used, Year of construction: 1992, spindle speed (min.): 7,500 rpm, spindle speed (max.): 24,000 rpm, 4 motorized grinding spindles (liquid-cooled, purge air / oil mist lubrication) including REFU HF frequency converter, e.g. for powering the spindles of a Voumard 400 CNC T4. Grinding spindle GMN TSSV 170-7500 Cpjdsl Tn Afepfx Afnsu 7,500 rpm, 350V, 19.3A, 7.5kW, 250 Hz Grinding spindle Voumard BM15-170 15,000 rpm, 350V, 35A, 18kW, 250 Hz Grinding spindle Voumard BM18-15032 18,000 rpm, 350V, 28.5A, 12kW, 600 Hz Grinding spindle Voumard BM24-150 24,000 rpm, 350V, 27A, 12kW, 800 Hz REFU HF Converter 316/25 High-frequency converter (inverter, frequency inverter) Frequency converter / inverter for powering motor spindles GMN tool spindle, motorized grinding spindle The spindles are fully functional, sold as is – manufacturing year approx. 1992 A collection of various grinding spindle shafts / arbors for grinding wheels is available for these spindles and can be purchased separately. Price / details on request All technical data subject to error or omission. We sell exclusively to countries within the European Community.

Condition: new, Year of construction: 2018, NEW PRODUCT at a special price Tactile coordinate measuring machine from Innometrik Measuring range 1200 x 3000 x 1000 Maximum workpiece weight: 1000 Kg Accuracy MPEE: 2.2 + L / 350 (in μm) Scale resolution: 0.1 / 0.5 in μm - Air bearings on all axes Linear speed: 300mm / s Volumetric speed: 520 mm / s Touch probe: Renishaw Tp200 incl. 3 modules (SF, HF, LF) and probe changer 3 compartment Software: OptiCheck 4.5 & Virtual DMIS (separate partitions) Optionally Polyworks according to customer requirements -Incl. PC (Windows 7) Alternatively Windows 10 Codpfedyl H Njx Afnspu -Incl. 2 monitors -Incl. Mouse keyboard Picture: sister device

Condition: excellent (used), Year of construction: 2003, max. wheel diameter 600 mm gear width 700 mm max. module 20 min. module 0,5 table diameter 300 mm x-travel 300 mm Cpsdpswyxycsfx Afnsu y-travel 600 mm z-travel 700 mm workpiece weight 300 kg Control Zeiss max. workpiece diameter 600 mm clamping length 20 - 1000 mm ical angle 90 ° total power requirement 2 kW weight of the machine ca. 2,5 t dimensions of the machine ca. 3,0 x 2,0 x 2,4 m Form measuring machine,gear measuring machine,coordinate measuring machine --> Primar MX 4 WL Suitable for transmission shafts, pinion shafts, gears, pistons, gearboxes, connecting rods, camshafts and crankshafts, crankcases, cylinder heads,... Air-suspended, centering and tilting table, support bearings, high-precision design! Software: Gear, hob, piston, bevel gear, crankshaft, tapered mandrel, drive bevel gear, connecting rod,... New software update 2014!