Plasma cutting machine

VOORTMAN V304

Condition: good (used), Year of construction: 2017, V304 plate processing machine (including 1 gantry beam(s) of 6.500mm and side trucks) ◼ This V304 plate processing machine is capable of processing plates up to 3.050mm x 18.000mm for bevel plasma cutting and marking (needle marker, if attached) and 4.100 x 18.000 mm for oxy-fuel cutting and marking (needle marker, if attached) ◼ X-rail (21.000mm on both sides of the machine, including double linear guides, helical rack and pinion system and rubber covering band) ◼ Plasma cutting and extraction table (4.300mm x 18.720mm, 2 channel(s), 1 pcs, suitable for ≥ 350A cutting) ◼ Position 1: Plasma cutting unit Kjellberg SmartFocus400 (1 pcs, automatic gas console, complete with cutting parameter database) ◼ Plasma 3D bevel unit (1 pcs, including 5 NC-axis, Voortman height control, intelligent torch positioning system and 3D collision sensor, for x- ,y- , k- and v-weld preparations) ◼ Driven suspension (1 pcs, servo motor driven, including laser pointer) ◼ Dross inhibitor (1 pcs, including 1,2L reservoir) ◼ Arc Glare protection (1 pcs) ◼ Position 2: Plasma cutting unit Kjellberg SmartFocus400 (1 pcs, automatic gas console, complete with cutting parameter database) Gusdpfx Asvpalaoiloi ◼ Plasma 3D bevel unit (1 pcs, including 5 NC-axis, Voortman height control, intelligent torch positioning system and 3D collision sensor, for x- ,y- , k- and v-weld preparations) ◼ Dragged suspension (1 pcs, with automatic addressing) ◼ Dross inhibitor (1 pcs, including 1,2L reservoir) ◼ Arc Glare protection (1 pcs) ◼ Position 3: Oxy-fuel cutting torch 4.0 (1 pcs, automatic gas console, ignition and piercing, complete with cutting parameter database) ◼ Voortman height control (1 pcs, capacitive height control) ◼ Dragged suspension (1 pcs, with automatic addressing) ◼ Position 4: Oxy-fuel cutting torch 4.0 (1 pcs, automatic gas console, ignition and piercing, complete with cutting parameter database) ◼ Voortman height control (1 pcs, capacitive height control) ◼ Dragged suspension (1 pcs, with automatic addressing) ◼ Position 5: Oxy-fuel cutting torch 4.0 (1 pcs, automatic gas console, ignition and piercing, complete with cutting parameter database) ◼ Voortman height control (1 pcs, capacitive height control) ◼ Dragged suspension (1 pcs, with automatic addressing) ◼ Cables high instead of low ◼ Donaldson fume extraction unit DFO 4-48 - 200L (incl. frequency controller) ◼ Air conditioning for switch panel (up to an ambient air temperature of 55°C) ◼ Hardware and software (includes VACAM ‘Machine Edition’, VACAM ‘Office Edition’, VACAD editor software module, VANEST nesting software, Layout marking software module, online support) ◼ Post processor for SigmaNEST (SigmaNEST is provided by the customer) ◼ Safety devices (safety bumpers, emergency stop cord)

Condition: used, functionality: fully functional, Year of construction: 2024, operating hours: 697 h, load capacity: 6,000 kg, lifting height: 29,900 mm, fuel type: diesel, construction height: 3,100 mm, empty load weight: 21,800 kg, drive type: Diesel, construction width: 2,500 mm, Rotating telescopic handler Technical condition: New Guodpfx Aijzb R Uyelsi Front tire condition: 80 - 100% Rear tire condition: 80 - 100% Battery voltage: 12V Rear work lights, front work lights, full cab, CE certificate, Image is for illustrative purposes only. Wheel chocks, TÜV preparation, 40 km/h, LED work lights on the telescopic arm, fixed part on the right side, car radio with USB and Bluetooth, external microphone, 100W LED spotlights around the machine, 5x vibration dampers for the telescopic boom, Active CRC.

Year of construction: 2013, condition: good (used),  Plasma cutting and extraction table, dimensions 2.500 x 6.000 mm.  Gantry bridge.  Carriage with servo-drives (to position the gantry bridge in X-direction).  Machine track, length 8 m.  HEB450 profiles for the foundation of the machine track, 8 m.  Plasma cutting unit Hypertherm HPR 400XD, 1 pcs.  Plasma bevel cutting unit, including automatic height control system.  Fume extraction unit Filtercube 4H for plasma cutting unit.  Oxy-fuel cutting torch, 3 pcs.  Automatic height control system IHT M4000 CAP for oxy-fuel cutting unit, 3 pcs. Gsdpetp Dhpjfx Ailjui  Torch suspension for oxy-fuel torch (motor driven).  Torch suspension Single Drive for oxy-fuel torch, 2 pcs (automatic torch positioning).  Laser pointer (to align and position the torch).  Computer control system (consisting of an industrial PC and a control panel).  Control software 'VACAM Machine Edition' (including VaCad and VaNest software and online support).  Automatic nesting software Sigmanest "Powerpack" (including 3 days of training for max. 3 persons at Voortman Holland (excluding travel costs and board and lodging) and 1 day online-support).  Emergency stop with stop cord.  Year of build: 2013.

Condition: new, Year of construction: 2026, Product characteristics The plasma burner or oxygen-gas CNC1 burner is a mobile device designed for cutting shapes out of a metal sheet. The machine does not require anchoring, thus reducing the assembly time considerably. Additionally, it enables for placing the machine in any location within the hall without any new expenses. The machine is equipped with an excellent quality wheel system that together with the low weight portal makes the plotter one of the fastest machines available on the market. The machine can be used for manual and automatic cutting. It is equipped with a digital controller that enables cutting out complicated shapes. The machine proves itself very well in the shipbuilding, machine-building and power industry. CNC1 has been equipped with a precise system of X/Y axes guides. The burner is controlled by Sino-USA electronic production system that is characterized by a high precision and elimination of the errors occurring during operation. The machine is very easy to configure. A manual configuration is possible for simple shapes and automatic configuration is possible for more complicated figures. The cutting pattern and the burner motion are shown on a display. An original FastCAM software is attached to the machine for easy configuration. The software is in English which makes the work easier. FastCAM is a technological CAD/CAM program, which is intended for designing and defining cutting paths of the elements cut out by CNC burning machines. The program shall be installed on an office PC or on a portable computer. After defining the way of cutting the operator receives a ready control code, which should be transferred to the control system of the machine. FastCAM program is a standard element of our machines. BASIC INFORMATION User-friendly interface – easy operation, even for people without prior experience of working with such programs as FastCAM Import of drawings in the *.txt format from any programs similar to e.g. AutoCAD, SolidWorks etc. MAKRO – a library containing standard shapes enables creating figures without the necessity of drawing them in CAD system. The program provides 2D figures NESTING – an optimal usage of sheet metal thanks to the automatic arrangement of elements on a sheet DEMO – shows a working path without having to turn on the plasma source or oxygen VOLTAGE HEIGHT CONTROLLER The machine is equipped with THC (a voltage control of the plasma burner blowtorch height). A precise control (+/- 0.1 mm) of the plasma blowtorch distance from a sheet metal during cutting. Higher accuracy and absence of defects which capacitive sensors and roller disks have. The parameters of the controller are collected automatically from the Automatic Cutting Parameters Selection table. Technical data Power supply 230 V LCD 7" color Code format Guedpovxhwvsfx Ailoi G-Code Working dimensions 1500×3000 mm Cutting speed 50–3000 mm/min Illustrations are preview only, the device is sold without the table. Manufacturer: Cormak

Condition: used, Year of construction: 2017, functionality: fully functional, machine/vehicle number: 2202, travel distance X-axis: 3,000 mm, travel distance Y-axis: 1,500 mm, type of input current: three-phase, input voltage: 400 V, input current: 50 A, Microstep Mastercut Eco Plus 3001.15 Year of manufacture: 2017 Control system: IMSNC Oxy-fuel cutting table: 3000 x 1500 mm Extraction duct left / right Plasma source: Kjellberg HiFocus 161i, adjustable 10 - 160 A Power source HiFocus 161i PLUS • Flexible adaptation of the cutting process to required conditions thanks to soft-switch inverter and microprocessor control • Optimal process control with ultra-fast regulation of cutting current • Process monitoring for torch cooling, ignition time, pilot arc time, short circuit time during torch ignition, and power source • Operating status and error display via LED and screen • Analog and serial interfaces for adaptation to CNC controllers • Infinitely adjustable cutting current from 10 - 160 A and during marking from 5 - 25 A • Optimal piercing through infinitely variable delay time for the main arc and adjustable current rise • Adjustable current reduction for cornering, start, and end signals of the guidance system • Automatic display of the preset cutting current • Serial data transmission for PC-based diagnostics Godpfx Aioy Nd Hysljui Plasma cutting technology: Contour Cut • Further development of HiFocus technology for mild steel • Optimized for cutting fine internal and external contours • High cutting quality and contour accuracy • Holes with angular deviations according to DIN EN ISO 9013 range 2-4 • Minimal angular deviations and smooth cut surfaces • Excellent repeatability and dimensional accuracy • No tedious post-processing – high productivity and low costs • No additional equipment, software, or new consumables required • Standard equipment Plasma torch PerCut 200/210 • PerCut 200 plasma machine torch for standard applications and high-precision bevel cutting • Quick-change PerCut 210 torch with threaded lock for quick and convenient tool swapping • Special torches available for special applications • Higher cutting speeds reduce cost per meter • Long service life of consumables conserves resources • Narrower kerf means fewer emissions and less waste • Significantly lower gas consumption compared to competitors thanks to efficient liquid cooling up to the nozzle tip • Lower noise levels due to reduced gas consumption • Bevel cutting up to 50 degrees with standard consumables • Cutting and marking possible with the same consumables Power source HiFocus 161i Power supply: 400 V; 3 Ph; 50 Hz Max. power input: 28 kVA (100% duty cycle) Main fuse, slow-blow: 50 A Protection class: IP22 Open circuit voltage: 330 V Cutting current: 10 – 160 A (100% duty cycle) Marking current: 5 – 25 A (100% duty cycle) Cutting range: Max. 50 mm Recommended: 0.5 – 38 mm Max. piercing thickness: 30 mm Weight: 206 kg Plasma machine torch PerCut 200 Quick-change torch PerCut 210 Clamping diameter: 50.8 mm Plasma gases: O2, N2, Ar/H2 Marking gases: Ar Swirl gases: O2, N2, Air, N2/H2 (F5)

Condition: used, Year of construction: 2011, CNC gantry plasma cutting machine Manufacturer: Eckert Type: Jantar 2 Gusdpfxsy Nqcbe Ailsi Year of manufacture: 2011 CNC control system Working area: 2 x 4 m 1 plasma torch with Kjellberg HiFocus 161i power source Automatic gas console Extraction table 121126ä

Condition: like new (used), Year of construction: 2017, functionality: fully functional, 2 recirculating air chamber furnaces, fast heating times, short process times, electric, warranty 12 months, immediately available -Temperature 200°C, increase to 250°C possible upon request -Charging car, 5 units offered, modification possible upon request -Homogeneous temperature distribution of +/- 10 °C Gsdpfey Avqwjx Ailoui -Internal dimensions WxDxH 3750 x 1400 x 2300 mm -External dimensions WxDxH 4850 x 1705 x 3880 mm -Usable volume 11.6 m³ -Control system S!MPAC with touch panel -Program execution with sensor as cascade control -Temperature limiter -Signal tower -Directly accessible, grid rails -Exhaust air volume flow 140 m³/min -Electromagnetic door lock -Rated power 180 KW -Connection 214 KW !!! -Weight approx. 3500 kg -Documentation, CE declaration of conformity We would be happy to offer transport and installation as well as training for your employees. Inspection in our machine hall is possible at any time by appointment. Furnace, Oven, Furnaces, Drying oven, Industrial oven, Drying cabinet, Heat oven, Heat cabinet, Recirculating air oven, Chamber furnace, Heating oven, Chamber recirculating air oven, Tempering oven, Temperature oven, Recirculating air chamber furnace, Hardening oven, Vötsch oven, Weisstechnik, Fusing oven, Postcuring, Post-curing of liquid crystal windows, CFRP support structures, CFRP support structure, Curing oven, Oven for glass, Glass tempering oven, Glass fusing oven, Glass hardening oven, bogie hearth furnace, car hearth furnace, shuttle kiln, bogie hearth kiln.

Condition: good (used), MicroStep SPL-PA plasma cutting system with extraction and compressor technology Manufacturer: MicroStep Group Model: SPL-PA 4501.15+S50 Current requirement: 120 A Machine type: CNC plasma cutting system CNC control: iMSNC Design: Portal design with linear guides Extraction system: Donaldson Torit DCE Electrical connection for extraction system: 400 volts Motor power of extraction system: 7.5 kW Compressed air generation: Screw compressor Compressor manufacturer: Kaeser Gsdoyvd Uispfx Ailsui Compressor model: TA 8 CE marking: present Location: Waltenhofen, Germany Dismantling and loading by the seller included.

Condition: good (used), functionality: fully functional, Year of construction: 2011, Biko 3128 – Plate Rolling Machine (2011) High-quality 3-roll plate bending machine for professional metal fabrication. Well maintained and ready for work. Technical Specifications Gsdpfxox Dx Hzs Ailjui Model: Biko 3128 Year of manufacture: 2011 Rolling type: 3-roll, initial pinch Max. plate width: 3100 mm Max. bending capacity: 28 mm (depending on material grade) Top roll diameter: To be confirmed Side roll diameter: To be confirmed Motor power: To be confirmed Control system: Hydraulic, with adjustable side rolls Cone bending capability: Yes Machine construction: Heavy-duty welded frame Safety: Emergency stop & foot pedal control Condition Machine is in very good working condition Regular service history Test run possible Included Foot pedal Hydraulic adjustments Dimensions & Weight (Confirm exact values with seller) Length: 5.0 m Width: 1.8 m Height: 1.6 m Weight: 12,000 kg

Condition: good (used), Year of construction: 1992, Hydraulic hole-punching machine, manufacturer: Häwa, year of manufacture: 1992. Operating pressure: 400 bar, with electrically adjustable height-adjustable support table. Machine is ready for operation. Gsdpfjgbk R Uox Ailjui