CNC turning automatic lathe

TSUGAMI B0266E-II

Condition: good (used), Year of construction: 2013, functionality: fully functional, machine/vehicle number: 123, spindle speed (min.): 200 rpm, spindle speed (max.): 10,000 rpm, total height: 2,200 mm, total length: 9,000 mm, total width: 1,500 mm, overall weight: 5,000 kg, controller manufacturer: FANUC, controller model: SERIES 32i-MODEL B, counter spindle speed (min.): 200 rpm, counter spindle speed (max.): 10,000 rpm, TSUGAMI B0266E-II CNC Automatic Lathe - Operating voltage: 200 V - Frequency: 50 Hz - Rated current: 21.4 A - Max. bar capacity: 26 mm - Max. machining length: 320 mm (synchronously driven guide bushing) - Without guide bushing: 50 mm - Max. drilling diameter: 12 mm - Max. tapping diameter: M10 - Deep hole drilling diameter: 10 mm - Max. clamping diameter sub-spindle: 26 mm - Max. drilling diameter sub-spindle: 10 mm - Max. tapping diameter sub-spindle: M10 - Max. drilling diameter tool spindle: 8 mm (front/rear tool holder) - Max. tapping diameter: M6 (front/rear tool holder) - Max. slot milling cutter diameter at tool spindle: 45 mm - Rotating guide bushing: 200 - 10,000 rpm (synchronously driven) - Tool spindle speed: 200 - 6,000 rpm - Total number of tools (standard specification): 31 - Tool size: 16 mm square x 100 mm - Rapid traverse: 32 m/min; rapid traverse in X1 and Y1: 24 m/min, in Y2: 24 m/min - Controllable axes: 6 The machine is equipped with a bar loader from FMB, type: TURBO 3-36, and a chip conveyor. Note: The item must be collected, by firm appointment, between 04 and 12 March 2026 (exact date to be coordinated). Hfodpfx Aaox Hxz Hjysr FCA D-75181 Pforzheim – loaded onto truck

Condition: used, Year of construction: 2012, Technical details: Hfsdpfevivx Njx Aayer turning diameter over bed: 20 mm spindle passage: 3-20 mm turning length: 250 mm control: FANUC 31 i-A main-spindle speed: 10.000 1/min subspindle speed: 10.000 1/min Main spindle capacity: 3,7 kW subspindle power: 2,2 kW number of tools: 35 weight of the machine ca.: 3,3 t dimensions of the machine ca.: 2,11 x 1,2 x 1,89 m CNC sliding headstock turning/milling centre with B-axis Control system: Fanuc 31i-A Machining length: max. 250 mm Number of controlled axes: 7 axes and max. 5 axes simultaneously B-axis: 0°-130° freely programmable Rod passage: Ø 3 mm to max. Ø 20 mm Drive power main spindle: 3.7 kW Drive power counter spindle: 2.2 kW Main spindle speed: 10,000 rpm Counter spindle speed: 10,000 rpm C-axis: Main and counter spindle Number of linear supports: 2 pieces Total number of tools: 35 pieces Dimensions (LxWxH) in mm: 2,110×1,200×1,885 Weight: 3,300 kg Conversion from long to short turning Deep hole drilling stations NAKANISHI high-speed spindle Rear slide with Y-axis Cross drilling rear side Chip conveyor Fire extinguishing system FMB bar loader Minimag 20, year 2012 Approx. 7.200 working hours *

Condition: good (used), Year of construction: 2014, functionality: fully functional, machine/vehicle number: 22012A, spindle speed (min.): 200 rpm, spindle speed (max.): 10,000 rpm, total height: 2,200 mm, total length: 9,000 mm, total width: 1,500 mm, overall weight: 5,000 kg, controller manufacturer: FANUC, controller model: SERIES 32-i MODEL B, counter spindle speed (min.): 200 rpm, counter spindle speed (max.): 10,000 rpm, TSUGAMI B0266E-II CNC Automatic Lathe - Operating voltage: 400 V - Frequency: 50 Hz - Rated current: 64 A - Max. bar stock clamping diameter: 26 mm - Max. machining length: 320 mm (synchronously driven guide bushing) - Without guide bushing: 50 mm Hodpfx Ajx Hxy Asaysfr - Max. drilling diameter: 12 mm - Max. tapping diameter: M10 - Diameter of deep-hole drilling: 10 mm - Max. sub-spindle clamping diameter: 26 mm - Max. sub-spindle drilling diameter: 10 mm - Max. sub-spindle tapping diameter: M10 - Max. tool spindle drilling diameter: 8 mm (front/rear tool holder) - Max. tool spindle tapping diameter: M6 (front/rear tool holder) - Max. cutter diameter (tool spindle): 45 mm - Rotating guide bushing: 200 – 10,000 rpm (synchronously driven) - Tool spindle speed: 200 – 6,000 rpm - Total number of tools (standard specification): 31 - Tool size: 16 mm square x 100 mm - Rapid traverse: 32 m/min; rapid traverse in X1 and Y1: 24 m/min; in Y2: 24 m/min - Controllable axes: 6 The machine is equipped with a bar feeder from FMB, type: TURBO 3-36, as well as a chip conveyor. Note: The item must be collected between 04 and 12 March 2026 on a binding date to be agreed. FCA D-75181 Pforzheim – loaded onto truck

Condition: excellent (used), pressure 0,5 - 20 t max. workpiece diameter 5 - 75 mm threading length 2000 mm pitch in mm 8 mm diameter of roll spindle taper 69,85 Hfjdpfxjvpaa Re Aayer tool diameter 200 mm roll spindle turning speed range 20 - 90 U/min stroke 0 - 20 mm total power requirement 7,5 kW weight of the machine ca. 3,1 t dimensions of the machine ca. 1,9 x 1,1 x 1,2 m

Condition: used, Thread Rolling Machine, Cold Rolling Machine, Thread Rolling Machine, Profile Rolling Machine Manufacturer: PEE-WEE Model: UPW 24 Serial No.: P07 Year of manufacture: 2007 Maximum rolling force: 24 tons Maximum tool diameter: 270 mm Roll spindle diameter: 69.85 mm Hfjdpfx Aaeuz If Njyor Tool bore diameter: 70 mm (nominal diameter) Maximum tool/reception length: 180 mm Maximum workpiece diameter: 50 mm Hydraulic motor power: 3 kW Roll drive motor power: approx. 5.5 kW Electrical connection: 400 Volt, 50 Hz, 10 kW - Pivotable roll spindle for through-feed thread rolling - Roll spindle speed adjustable in 4 steps via gearbox shift - Hydraulic unit integrated in the machine base - Operating manual with electrical schematic Space requirements (L x W x H): 2,000 x 1,450 x 1,900 mm Weight: approx. 3 tons Very good condition Plunge Rolling: The thread rolling tools, having the same pitch as the workpiece, form the thread by penetrating the workpiece up to the nominal diameter. The maximum thread length is limited to the width of the rolling dies. Through-feed Rolling: Used when the thread length is greater than the width of the rolling dies. Through-feed tools are divided into three sections – entry, calibration, and exit. Knurling rolls have no pitch and are swiveled at the lead angle corresponding to that of the profile to be rolled. Lead angle rolls differ from knurling rolls by having a pitch in the profile. The sum of the lead angle and swivel angle results in the effective lead angle in the workpiece.

Condition: good (used), Year of construction: 1973, pressure 0,5 - 10 t max. workpiece diameter 2 - 50 mm threading length 2000 mm pitch in mm 3 mm diameter of roll spindle taper 54 tool diameter 145 mm Hfodpfjvpaaksx Aayjr roll spindle turning speed range 41 - 129 U/min stroke 0 - 8 mm total power requirement 4,5 kW weight of the machine ca. 1,3 t dimensions of the machine ca. 1,3 x 1,2 x 1,2 m

Condition: used, Year of construction: 2015, x-travel 500 mm y-travel 700 mm z-travel 400 mm solution in X-, Y- und Z-axis 0,0001 mm weight of the machine ca. 625 kg dimensions of the machine ca. 1,1 x 1,2 x 2,2 m table load 180 kg workpiece height max. 545 mm table-size 1160 x 730 mm MITUTOYO CRYSTA-APEX S574 Coordinate measuring machine Length measuring deviation: 1.9 + 3 L/1000 Measuring range: X-axis: 505 mm Y-axis: 705 mm Z-axis: 405 mm Hsdexwp Hropfx Aayofr Resolution: 0.0001 mm Traversing speed: 8 - 300 mm/s Speed: 519 mm/s # MCOSMOS v4.2 R4 software runs on PC with Windows 7 Pro # The probe head is a PH10M with attached modules SP25M + SM25-2 / Can also scan

Condition: ready for operation (used), Year of construction: 2022, General Data Machine weight 200 kg Main Drive Hsdpfx Aox D N Hxoayjfr Number of axis 3 Workpiece Workpiece weight 90 kg This 3-axis MAHR MarSurf CD 140 CMM machine was manufactured in 2022. It features a contour probe system with a resolution of up to 6 nm and a traversing length from 0.1 mm to 140 mm. The machine supports a workpiece weight of up to 90 kg and offers adjustable measuring forces from 4 mN to 30 mN. If you are looking to get high-quality contour measuring capabilities, consider the MAHR MarSurf CD 140 machine we have for sale. Contact us for more information. Application Types Measuring

Condition: used, Year of construction: 2018, operating hours: 13,164 h, Type of fuel: LPG Empty weight: 4.029 kg Dimensions (LxBxH): 260 x 120 x 248 cm Lifting capacity: 2.000 kg Lift height: 367 cm Fork length: 1.200 mm - Year: 2018 - Documentation available: Yes - CE marking present: Yes - CE certificate present: No - Serial number: 517306J00014 - Operating hours: 13164 - Lifting capacity: 2000kg - Lifting height: 3670mm Hsdpswnintjfx Aayjfr - Overhead clearance: 2480mm - Fork length: 1200mm - Number of wheels: 4 Wheels - Attachment: Side-shift - Options: Work lights, Heating, Full cabin - Mast: Duplex - Inspection valid until: 06.2025 - Drive: LPG - Motor brand: Still - Transport dimensions: 2600mm x 1200mm x 2480mm (l x w x h) - Transport weight [kg]: 4029kg - Transport packages [pcs.]: 1 Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Tess van den Boom

Condition: used, Year of construction: 2011, functionality: fully functional, machine/vehicle number: 141447, Technical characteristics: Max. measuring range in mm X axis 500; Y axis 500; Z axis 500 Dimensions in mm Without base: length: 1160; width: 1080; height: 1803 With base: length: 1170; width: 1090; height: 2480 Mass of CMM in kg: without base: 350 with base: 445 Max admissible workpiece mass in kg: 100 Equipment consists of: Coordinate measuring machine (CMM) with base Control (integrated) Control console Software (Calipso 5.4) Documents Probing system Master stylus Reference standard Changer rack Machine status: WORKING Hfjdpoxxvbrefx Aayor