Ram broaching machine X/Y 650 x 510 mm

STANKO 7D430

Condition: excellent (used), Year of construction: 2001, turning diameter over cross slide: 1,600 mm, turning length: 6,000 mm, turning diameter: 1,300 mm, spindle motor power: 100,000 W, total height: 2,875 mm, total length: 9,550 mm, total width: 2,950 mm, workpiece weight (max.): 40,000 kg, Swing over bed Ø 1600 mm Swing over cross slide Ø 1300 mm DBC Turning Length 6000 mm Spindle power 100 kW Tailstock spindle Ø 280 Ø Stroke pinole 200 mm Fodpfx Aoymk E Ajb Ajgg Workpiece weight 40000 Power 125 A Speeds / ranges 250 Rpm Dimensions (Estimate) Length 9550 mm Width 2950 mm Height 2875 mm Weight 41000 kg Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!

Condition: like new (used), functionality: fully functional, Weiler center lathe Model Condor 81 guidance and feed spindle lathe with 3-axis digital display from K&C, NEW Geometrically overhauled with inspection protocol for new machine tolerances Technical data: >> Machine No. 84-121 >> Center height 165 mm >> Center distance 750 mm >> Spindle speeds: from 22 to 2800 rpm >> Spindle bore 40 mm >> Short taper spindle head DIN 55027 size 5 with bayonet lock >> Tailstock MK 3 >> Feeds from 0.015 to 0.46 mm/rev >> Possible threads: metric, imperial, module, and diametral pitch >> Metric thread pitches from 0.18 to 28 mm >> Weight approx. 1100 kg >> Spindle brake switchable >> Length 1.83 m, Height 1.29 m, Depth 0.88 m Equipment and accessories: >> 3-axis digital display from K&C, new, 12 months manufacturer warranty with operating instructions Functions: switching mm/inch, coordinate selection ABS/INC, value halving, reference mark, tool programming for 200 pcs., taper calculation, radius/diameter, quick zeroing, count direction switching >> Collet chuck NEW, collets NEW from 3 to 26mm, increments of 1mm >> 160 mm three-jaw chuck with 2 sets of jaws NEW >> Multifix size B NEW with 3 piece steel holders >> Bed stop >> Electric chuck guard NEW >> Rear wall Fgjdpfx Abjwrm Dto Ajg >> Operating manual >> Coolant device >> Machine feet About the machine: A Weiler Condor 81 guide and feed spindle lathe in a very good, geometrically overhauled condition is being offered. The guides are newly ground or newly scraped. Inspected according to test protocol. The accessories collets and chuck are new. For safety: The machine has a brake motor, electronic spindle guard and two emergency stops, making it an absolutely as-new lathe. Even at high speeds, the Weiler runs very smoothly. This newer generation of Weiler lathes is very user-friendly and allows surfaces as if ground to be produced. Take the opportunity to view this machine on site under power and convince yourself of its condition.

Condition: ready for operation (used), Gear shaping machine STANKO 5M150 Max. diameter of gears that can be cut: 800 mm Max. module: 12 mm Max. cutter stroke: 200 mm Saddle indexing gear diameter: 360 mm Distance between axes (tool and table): 0-700 mm Largest tool diameter: 200 mm Cutter arbor diameter: 44.443 mm Taper: M5 Table diameter: 800 mm Distance from floor to table: 870 mm Indexing gear diameter: 762 mm Table hole diameter: 120A mm Double stroke per minute (s.p.m.): 33-188 mm Range of table feed rates per cutter double stroke: -Circular: 0.2-1.5 mm -Radial: 1-5.4 mm Fsdpfsqcvkvox Ab Aogg Table rapid rotation speed: 1.7 rpm Table rapid travel speed: 137 mm/min Cutter rapid rotation speed: 3 rpm Main electric motor power: 4.8; 5.7; 7.5 kW Dimensions: 3100x1800x3500 mm Weight: 10200 kg

Year of construction: 1981, condition: excellent (used), faceplate diam 1300mm max turning diam 1100mm range of turning diam 460-1250mm Fgjdpfsk Dz N Iox Ab Aog

Condition: ready for operation (used), An old Colchester engine lathe is available. Center height: 216mm, swing diameter over bed/cross slide/in gap: 432mm/267mm/711mm, distance between centers: 2000mm, spindle bore: 76mm, speed: 1600rpm, bed width: 343mm. Machine dimensions X/Y/Z: approx. 3200mm/1100mm/1400mm, weight: approx. 2500kg. An on-site inspection is possible. Fedpfey E S D Ejx Ab Aogg

Condition: used, Year of construction: 1976, turning diameter over bed 600 mm turning diameter over slide rest 400 mm turning length 1000 mm Fgodow Tdxcepfx Ab Aog turning diameter in the gap 850 mm turning speeds 15 - 810 U/min centre height 300 mm spindle bore 56 mm total power requirement 9,0 KW weight of the machine ca. 2,9 t dimensions of the machine ca. 2,8 x 1,45 x 1,65 m Center lathe - Forkardt 3-jaw chuck F 315 - Single-jaw tool post - Steady rest - Live center - Chuck guard, limit switch monitored - Chip tray

Condition: ready for operation (used), Year of construction: 1998, table mounting size: 765 x 400 mm movements x/y/z: 650/410/510 mm spindle taper: BT 40 min./max. distance table/spindle: ca. 90/690 mm spindle turning speed range: 80 - 8000 rpm number of tool positions: 20 pieces carriages: ca. 30 m/min rapid move: ca. 30 m/min Fedotwy Dispfx Ab Ajgg electrical connection: 380 V, ca. 15 kVA kW space needed: 2300 x 2100 x 2650 mm weight: 4000 kg

Condition: used, Year of construction: 2004, fuel type: gas, weight max. in kg 2500 kg stroke 3050 mm fork length 1200 mm load centre 500 mm turning radius 2444 mm driving speed 22 km/h Fgsdpfx Abjr Dg H Eo Ajg guage width vorne 1008 mm guage width hinten 932 mm weight of the machine ca. 3,64 t dimensions of the machine ca. 3,8 x 1,25 x 2,25 m

Condition: excellent (used), Year of construction: 2006, functionality: fully functional, Erlo SEAR 25-RS drill, gear drill with automatic feeds, includes threading system, spindle speeds 64-3060 rpm, with chuck and protection, machine in very good condition, year 2006 Fgjdpfx Abjv Rnhxo Asg

Condition: reconditioned (used), Year of construction: 2015, functionality: fully functional, With 3-axis digital display Year of manufacture: 2015 Spindle bore: 54 mm Distance between centers: 1000 mm Center height: 200 mm Speed range: 30 – 3000 rpm, stepless speed control with display on screen Including the following accessories: Multifix tool holder Coolant system Three-jaw chuck Ø 200 mm Four-jaw chuck Ø 250 mm Collet chuck complete with collets up to Ø 32 mm Chuck guard Chip guard with lighting Fixed steady rest Ø approx. 150 mm Travelling steady rest Ø approx. 100 mm 4 pcs. height-adjustable machine feet 1 pc. live center Fodeyybxnspfx Ab Aegg Operating manual