Machining center

SCM morbidelli x400

Condition: used, Year of construction: 2011, Base Machine M800 X5 TV 1 WORKING RANGE X: 5,020 mm Y: 1,830 mm Z: 675 mm Clearance Height: 300 mm (from 50 mm suction cup height) MACHINE STRUCTURE The base structure is a monolithic construction made from thick-walled steel. It is reinforced across the entire machine bed with welded components, providing exceptional stability. The table design, with its large base, is the key to ensuring lasting precision and stability. The machine’s layout enables the operator to achieve optimal workflow with minimal space requirements. The mobile gantry is built as a solid monoblock. It is positioned in the X direction on prismatic, ground guides with recirculating ball carriages. The machining unit is mounted on this mobile support carriage, also on prismatic, ground guides and recirculating ball carriages. AXIS MOVEMENT All axes travel on prismatic linear guides with large cross-section and recirculating ball shoes with a wide contact surface, which ensures optimal sliding, even at high speeds and accelerations. The precise and fast positioning of the movable gantry (X-axis) is achieved via helical rack and pinion. Large cross-section recirculating ball screws ensure accurate positioning of the machining unit along the movable gantry (Y and Z axes). The perfect mechanical dynamics and maximum positioning accuracy are controlled by high-quality drives and brushless motors. Max. axis speeds: · X-axis = 90 m/min · Y-axis = 90 m/min · Z-axis = 30 m/min Safety device with bumper and light barrier 1 Bumpers with sensors are fitted to the movable upright, and a light barrier system is installed at the front of the machine. If the operator enters the active zone, the X-axis travel speed is reduced to a lower value of 25 m/min without stopping the machine. This system allows parts to be loaded during pendulum operation without the limitation of access areas, as seen with pressure mat systems. This prevents unwanted interruptions in the machining cycle and offers greater freedom of movement around the worktable. CE certification for the safety system 1 Safety protection fence 1 Side and rear protection fence Automatic central lubrication controlled via CNC 1 The lubrication of the X, Y, and Z axes is controlled by the CNC; intervals are regulated automatically, without manual intervention. Central extraction connector 1 All individual extraction connections of the machining units are collected into a central extraction port. Inside the port, there are various slider valves controlled by the NC. This reduces the required extraction air volume. Chip conveyor 1 Maxi – 5-axis electrospindle 11 kW HSK-63 “Prisma K 1 5-axis electrospindle, 11 kW at 20,000 rpm S1 (100% duty cycle) Speed: max. 20,000 rpm Rotation direction: left/right Liquid cooling Tool interface HSK 63F Inverter 18 kW, stepless, smooth power delivery Max. rotation B-axis = 200° (+-100°) C-axis = 650° Thanks to the non-orthogonal axes, it is possible to perform complex horizontal positioning in a small workspace. This enables the machining of complex geometries without the risk of collision. Ksdpfexy Tmnex Akzolt

Condition: used, Year of construction: 2014, total height: 2,400 mm, total length: 4,500 mm, total width: 2,200 mm, Colour: Grey Empty weight: 2.500 kg CNC Machining Center Biesse skill 12 24 G FT Year of construction 2014 Machine no. 60961 Recording HSK F63 10x vertical drilling 12 switch positions Software: BiesseWorks X axis 2465 mm Y-axis 1260 mm Z axis 324 mm Disassembled for transport on normal trailer; 4500x2200x2400mm; Kodpfx Akownhanozolt Own weight 2000kg - Details: - └ Description: Pallet with white control box does not belong to this machine - Year: 2014 - Documentation available: Yes - CE certificate present: No - Serial number: 60961 - Number of milling spindles [pcs.]: 1 - Type milling table: Flat table - Drilling unit present: Yes - └ Vertical drilling spindles [pcs.]: 10 - Tool changer positions [pcs.]: 12 - Vacuum pump present: Yes - └ Number [pcs.]: 1 - └ Brand: Becker - Working range X [mm]: 2465 - Working range Y [mm]: 1260 - Z-axis working range [mm]: 324 - Transport dimensions: 4500mm x 2200mm x 2400mm (l x w x h) - Transport weight [kg]: 2500kg - Transport packages [pcs.]: 1 Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Glenn Smeets

Condition: ready for operation (used), Year of construction: 2007, operating hours: 46,000 h, Axes: 4, load capacity: 180kg, working radius: 3200mm, positioning accuracy: +/-0.25mm, max. total load: 430kg, cycle output: 30/min. Control: KR C2: max. control axes: 6, weight: approx. 35kg. Robot weight: approx. 1200kg, dimensions X/Y/Z: approx. 1200mm/1800mm/1700mm, robot set-up dimensions X/Y: approx. 1000mm/1000mm, operating hours: approx. 46000h. Documentation available. An on-site inspection is possible. Klodpfjt R Trfox Akzot

Condition: excellent (used), SINGLE SIDE EDGE BANDER (Left) Edges (band in rolls) thickness (Min/Max) mm 0,4 / 3 Edges thickness in strips / lippings (min/max) mm 0,4 / 8 (12)* Panels thickness (min/max) mm 8 / 60 Ksdpfoxlqntox Akzolt Numerical Control "StarTouch" + "Touch 7" Feeding speed m/min 12-18 Top pressure system with rubber belt (C.N.) Spraying unit (Anti-sticking liquid) AAR In-feed fence, adjustable by N.C. "EASY SIZE PLUS" Pre-milling Unit (vertical joint trimmers) 2 x Kw Lamps to heat the workpieces side Glueing Unit (P.U.R. Glue + Quick Melt system) "VC/800" - "VC/6" + "AirFusion AF15" Band Pressure zone (N.C. adjustment) Edge coils supporting unit - 1 Snipping (end-cutting) K/SEL Rough Trimming unit RS/K Fine Trimming unit RI / 800 (3 pos.) Multi Function Unit (Profile contour Trimming Unit) “4 EDGE” KIT Spraying Unit (for sliding liquid) Profile edge scraping unit RAS/1000 Glue scraper RCA / 2C Milling grooving unit K-100 (1 x Kw 1,8) 90° Hot Air Heater (to reactivate the color of plastic tape) Panels Return System "SAG" Mod. SPINNER 47 / 63

Condition: new, Year of construction: 2024, TECHNICAL DATA Table size 1100 x 760 mm table height 870 mm milling spindle not interchangeable 30 mm clamping height 140 mm height adjustment 125 mm suction socket 2 x Ø 120 mm speed 3000 / 4500 / 6000 / 9000 rpm Colour RAL 7035 light grey and RAL 5000 violet blue Net weight approx. 800 kg TECHNICAL DESCRIPTION Solid German mechanical engineering Table milling machine with one-sided swivelling fixed milling spindle for swivelling range from -5° to +45.5 Positioning control for height and swivel adjustment with zeroing of the height and offset measurement travel Electronic position and speed displays 4 speeds 3000 / 4500 / 6000 / 9000 rpm Belt quick tensioning device Push button for spindle start and stop Left and right rotation Cutter quick clamping device Fine planed cast iron table with rigid frame support Control panel at the bottom of rigid frame support Milling stop 216 total adjustment via handwheel and LCD display incl. cast stop plates and aluminium splitter tongues Machine socket Lockable main switch Klodsfpb Nmepfx Akzot Mechanical motor brake Milling protection and pressure device GAMMA V 1629 Curved milling fence 1639 Tapoa Milling spindle 30 mm, not exchangeable CE-conform GS tested

Condition: refurbished (used), FULL LINE of Drilling, max working width mm 3200, with fast automatic handling equipment. Composed of the following machines: A) LOADER (Portal) "RBO" Winner C 3200 with double pick-up and central motorized rollers table. With 2 on-ground motorized rollers ways to in-feed the piles (stacks) of panels to loader. B) TRANSFER (Connecting Rollers Table with 90° conveyoring belts) “RBO” Mod. Transfer TA 90° C) 1st Auotmatic BORER "BIESSE" Mod. Techno FDT with No. 2 Horizontal Units + No. 7 Vertical Bottom Units D) 2nd Automatic BORER "BIESSE" Mod. Techno FDT with No. 2 Horizontal Units + No. 7 Vertical Bottom Units Klsdpfx Aodfgg Iskzot E) TRANSFER (Connecting Rollers Table with 90° conveyoring belts) “RBO” Mod. Transfer TA 90° G) UNLOADER-STACKER (Portal) "RBO" Winner SC 3200 with double pick-up, with double storage station, with central motorized rollers table. With 2 on-ground motorized rollers ways to out-feed the piles (stacks) of panels from the Unloader

Condition: like new (used), Year of construction: 2022, functionality: fully functional, HOMAG Sandteq w-300 Technical Data: - Feed belt speed: 2.5 - 13 m/min - Working height: 900 mm - Working width: 1350 mm - Number of processing units: 2 - Workpiece thickness: 3 - 160 mm with automatic measurement - Machine dimensions (LxWxH): approx. 2115 x 2100 x 2415 mm Kedpfx Ajxczmzskzelt - Machine weight: approx. 4000 kg - Total electrical power: approx. 39 kW - Recommended main fuse: 80 A - Vacuum table - Q = Cross sanding unit Poly V-belt / 13.5 kW (2-16 m/s) - X = Combination unit with contact roller & pressure beam system / 18.5 kW (2-18 m/s) - Super-finish function: calibration, veneer & intermediate lacquer sanding, veneer & fine lacquer sanding - Brushing unit - Cleaning rotator with ionization - Powercontrol with Powertouch The machine is available immediately. Loading onto truck possible.

Condition: new, Technical data: Max saw diameter: 400 mm Min saw diameter: 250 mm Saw spindle diameter: 30 mm Scorer diameter: 120 mm Scorer spindle diameter: 20 mm Scorer on a separate engine Manual saw height adjustment Tilting saw at an angle from 0° to 45° Manual adjustment of the saw angle Carriage length: 3200 mm Carriage lock Work table: 1450 mm x 1030 mm Table height: 920 mm Table extensions 2 x Klodjv S Uz Ispfx Akzst Culaga Guard Safety switch Power supply: 380 V Main engine power: 7 kW Overall dimensions: Length: 3430 mm Width: 1900 mm Height: 1560mm

Year of construction: 2024, condition: new, This CNC milling machine is an excellent tool to take your hobby to the next level. The 0404 mini is both convenient and compact, making it suitable for any workshop. The Wattsan desktop router can operate on wood, plastic, plexiglass, aluminum, brass, and more. The Wattsan 0404 mini's cast-iron frame ensures accuracy and stability throughout any type of demanding operation. It can make a 3D mill. Our CNC milling machine includes a T-slot table that allows you to secure items using bolts, clamps, or a mechanical holdback. You can give our managers a call for additional details! Wattsan 0404 mini characteristics: Working area: 400 x 400 mm Spindle: 1.5 kW Machine size: 710x710x740 mm Packing size: 860x860x810 mm Weight: 155 kg Virmer provides not only prime machines but also service and delivery. Our engineers and managers are ready to answer all of your questions and provide video assistance if required. Also, owners of Wattsan equipment get lifetime online support. Klsdoiinkkepfx Akzot Virmer is located in the Netherlands and works all over Europe. Virmer is Wattsan's official supplier. We provide not only laser engravers, but also metal cutters, welders, markers and cleaning machines. Wattsan is a Chinese manufacturer, which has been creating laser equipment for almost 15 years and keeps evolving with the help of its clients. Thanks to feedback Wattsan made over 50 modernizations, which made machines more reliable, precise and powerful so you could upgrade your business up to the new level. YOU CAN WRITE OR CALL US! WE WILL SELECT THE RIGHT MACHINE FOR YOUR TASK On our company you can find a wide range of machines and components: Laser Metal Cutting Machine; Laser Metal Machine, Fiber Metal Laser, Fiber Metal Laser Engraver; CNC laser machine for metal; Laser machine for wood; CNC laser machine; Laser engraving machine; Laser engraver; Laser cutting machine for plywood; Laser engraver; Laser cutting machine for metal; CNC milling machine; laser marker. Lenses; Chillers; Cooling system for machine; Chiller S&A ; IPG laser, MAX photonics, Raycus; Compressor; Rotary device; Mirror for laser machine.

Condition: used, functionality: fully functional, input voltage: 400 V, type of input current: three-phase, cutting height (max.): 400 mm, saw band length: 5,550 mm, saw band width: 80 mm, table length: 800 mm, table width: 1,060 mm, working height: 400 mm, - Italian manufacture - Lamella band saw - Unpainted - Very good condition - Used saw Band Saw: - Wheel diameter: 800 mm - Max. blade width: 80 mm - Max. cutting height: 400 mm - Main drive motor: 11 kW - Feed speed range: 2–40 m/min - Feed system with pneumatic pressure to the guide - Metal slip-in feed roller - Blade length: 5550 mm - Throat (blade-to-frame distance): 780 mm - Screw-type blade tensioning Kljdpfjw H Rq Hex Akzst - Table size: 1060x800 mm - Tilting worktable: up to 15° - Extraction port diameter: 120 mm - Blade lubrication system - Foot brake - Cast wheels - Star/Delta starting - Power supply: 380V - Dimensions (LxWxH): 1600x1100x2400 mm - Weight: 860 kg Feed Unit: - Metal, toothed, drive roller - Five feed speeds, selectable by belt adjustment - Roller height: 30 mm - Feed motor: 0.75 kW - Pressure system