Beer Filter

Schenk Filterbau Gmbh ZHF-S 25

Condition: used, Year of construction: 2024, functionality: fully functional, Corrugated line 5 ply. Fully renewd 2024, 1650mm width. Steam matic, boiler steam producing 2500 kg/h. Max pressure 19 bar. Speed up to 70 metr per min. 1.⁠ ⁠Total Length: 55 metr 2.⁠ ⁠Total Power: 150 kw 3.⁠ ⁠Frame with shaft 4.⁠ ⁠Corrugated paperboard marching: diameter of corrugated rouer, electric adjust speed moter used. 5.⁠ ⁠Double cylinder gum mounting marchine: On the adoption, inside two layers draw the gun, dascend to carry the paper lead the paper roller. Machine exists units: Hydraulic shaftless mill roll stands, Spindle ¢ 240mm, hyperbolic heavy rocker, expand chuck , multi-point brake, hydraulic drive lifting, panning left and right on the middle. Top paper preheat cylinders and core paper preheat cylinders. Both preheat 360 degress area. Single Facer Rcjdow R Sknopfx Ab Eed Double Facer Blade scorer NC helical knife Glue system Gas system Steam system producing 2500 kg/h. Max pressure 19 bar. Working 12 bar. Top paper index 100g/㎡--180g/㎡ Ring crush index（N.m/g）≥8 (Water containing8-10%) Core paper index 80g/㎡--160g/㎡ Ring crush index（N.m/g）≥5.5 (Water containing8-10%) In paper index 90g/㎡--160g/㎡ Ring crush index（N.m/g）≥6 (Water containing8-10%)

Condition: excellent (used), Year of construction: 1995, Combination Unit: Manufacturer: GSG Feeder: Type: 840.02-027 Crusher Descaler: Type: 663.02-017 Wire Range: Ø5.5-16mm For wire rod with approx. 40-60 daN/mm² strength Crushing and Bending Rollers: Carbide Inserts Adjustment with 0.37 kW - 1.15 A gear motor Brush Drive with 0.25 kW gear motor, n=293 rpm Connection Voltage: 380-420 V 50 Hz Dry Coating Unit: Type: BSG/T Filling: Calcium Stearate (e.g., Traxit Type: D S 51 E) Stearate Consumption: approx. 350 g per t of wire Drawing Speed: max. 15 m/s Electrical Power: 2x 0.55 kW gear motors Cassette: 2 slots (supplied with 1x roller block + 1x cassette) Type: PKG/T (TS) Cleaned rolled wire Wire strength approx. 40–60 daN/mm² Wire range max. inlet diameter 9.5mm, finished diameter 3.5–8.5mm Roll dimensions min. Ø115mm, max. Ø125mm, Bore diameter Ø82mm, width 15–25mm Cooling pin diameter 25mm Cooling water consumption approx. 600 l/h Drawing machine: Manufacturer: Koch Type: KHZ 5000 Year of manufacture: 1993 Serial number: 13.821 Number of draws: 1 draw per block Drawing drum: Ø700mm Tensile force: mechanical 5000 N Wire material: mild steel wires Run-in strength: approx. 40 – 45 daN/mm² Maximum drawing range: Inlet diameter 5.0 – 8.5mm Rsdpsr Nfvmofx Ab Ejcd Cross-section reduction: 20 x 25% (mechanical gradation) Drawing speed: up to max. 7.0 m/s Brake: Twiflex, type: MRB Drive: AC motor/frequency converter, Siemens PN=110 kW, n=1485 rpm Spooler: Manufacturer: Koch Type: KHS 1250 Year of manufacture: 1993 Factory No.: 13741 Wire diameter: 5 – 8.5 mm Strength: approx. 55 – 70 daN/mm² Winding speed: V=7 m/s, adapted to the drawing machine Filling weight: approx. 3000 kg Spool drive motor: Three-phase motor with external fan Type: 1 PQ 6253 – 6 AA 70- Z A 15 + K 20 + C 14 + H 46 P=37 kW, n=1000-2000 rpm, IP54, design B3 Laying drive motor: 66-671U, 1.5 kW, 170 V, 9.8 A, 1680 rpm, IP 44, B5-200 With Attached tachometer generator TG 20, 20 V / 1000 rpm With attached spur gear SK 32, i=57.53, design B6 Hydraulics: Hydraulic excavator type: H13 AK Pneumatics: Twiflex disc brake type: MRB Pneumatic cylinder type: SPWG 28032-25mm stroke Dimensions: 3100 x 3000 x 1700 mm (L x W x H) without counterweight

Condition: used, Year of construction: 2026, operating hours: 15 h, functionality: fully functional, machine/vehicle number: 204065, total width: 2,900 mm, total height: 3,300 mm, Used machine CNC cutter/plotter Cutting area in X and Y: 2,500 x 2,100 mm. Multifunctional CAM cutting system in CNC knife technology for 2D cutting of leather, fabric, technical textiles, foam and other flat, semi-flexible or rigid, non-metallic materials. Equipment of the used machine • 1 cutting bridge and 1 multifunctional tool head The machine is sold with one driven circular knife, electric oscillating knife and one Milling Head + exhaust • Multifunctional tool head to hold max. 3 interchangeable tools • powerful vacuum blower for fixing the material • Standard equipped with gray conveyor table (Conveyor). Green-blue exchange conveyor possible (offers high contrast for dark materials) Can be extended with other tools (on request): • EOT electric oscillating blade • POT pneumatic oscillating knife • PRT rotating blade • UCT universal blade • KCT Kiss-Cut tool • CTT creasing tool • V-Cut angle-cut cutting blade • Punching tool for pinches or holes • Printer mark detection • Camera registration Easy-to-use function • Easy interchangeable cutting tools, "PLUG & CUT • Intuitive user interface • Easy blade change • Vacuum zones can be activated with a click Fast amortization • Low cost with high added value • Best material utilization through nest expert software modules (not included in equipment) • High velocity • Constant precision Data: • Short cutting times due to high positioning speed up to 90 m/min. • Repeatabiliy +/- 0.25 mm • Cuts single or multiple layers • Suitable for both single ply and multi ply or sheet goods and roll goods (can be extended with suitable unwinder) (Product photo as example) The machine is CE certified. Rjdoif Ek Rjpfx Ab Ejcd

Condition: excellent (used), Year of construction: 1993, CNG Tank Gas Methane Trailer Natural gas 200 Bar Manufacturer: SAMRO Year: 1993 Tare: 6900 kg Rodpot D Aptefx Ab Eocd We also have other tanks for LIN, LOX, LAR, LNG and CO2, argon, oxygen, nitrogen and carbon dioxide, Hydrogen, Methane We would also be happy to provide you with a quotation or give you more information about other pressure vessels.To discuss the possibilities, please contact us by phone or e-mail.

Condition: good (used), Consisting of : - 3 tanks of 18000 litres - 3 tanks of 15300 litres - With walkways - Material: AISI 316 Rcjdpfx Aboib H Ddj Esd - Square discharge door (bottom) - Motorised mash discharge - Round manhole DN 400 (cylindrical part) - Total emptying: ball valve Ø 40 Friedrich no 2 - Partial drain: ball valve Ø 40 Friedrich no 2 - Taster - Recirculation with ball valve Ø 40 Friedrich no 2 - Dome Ø 400 mm, eccentric - Central dome DN 400, with a cylinder-grid fixed inside (to keep the mash cake wet) Dimensions : - 3 tanks 18000 litres: Ø 2000 mm, height 5600 mm - 3 tanks 15300 litres: Ø 2000 mm, height 4800 mm - Ground clearance: approx. 550 mm

Condition: used, Year of construction: 1983, grinding length 8400 mm grinding width 1450 mm workpiece height 1250 mm surface area 8000 x 1250 mm table height over floor 920 mm distance between columns 1470 mm Rcsdpfx Ajvr Hgvsb Eed workpiece weight max. 59700 kg weight of the machine ca. 59,7 t dimensions of the machine ca. 22 x 5 x 5 m Adjustment ranges: -Crossbeam, vertical 1250 mm -Grinding support, horizontal 3100 mm Adjustment speeds: -Machine table (X-axis) infinitely variable 1-45 m/min Table creep speed 5 m/min -Grinding support, horizontal (Y-axis) Rapid traverse 3000 mm/min Feed, step 0.001-0.099 mm Feed rate, continuous 100-3000 mm/min Creep speed 18+1 mm/min Tip infeed 0.001-0.019 mm -Crossbeam (W-axis) Rapid traverse 410 mm/min Table drive: -Oil transmission, Type Iv4 -Cylinder-Ø 185 mm -Piston rod Ø 130 mm -Drive motor 22 kW

Condition: ready for operation (used), Year of construction: 2003, Complete Tetra Pak line TBA 21-1000 Slim, includes: Rcjdpfeycwvaex Ab Eed 1. TBA/21 1000 Slim filler, V050, YOM 2003, 52.000 running hours 2. CAP30 cap applicator for Helicap23 Pro26 3. Easy Ride Terplus cartons accumulator 4. TCBP70 wrap around packer 5. Conveyor system 6. Conveyors system The line is in very good condition, still in production till April. Can be sold without CAP30 applicator.

Condition: excellent (used), Year of construction: 2009, operating hours: 8,303 h, functionality: fully functional, machine/vehicle number: 33365B, color channels: 5, paper weight (max.): 600 g/m², paper width (min.): 180 mm, paper width (max.): 520 mm, paper height (min.): 148 mm, paper height (max.): 360 mm, counter reading (color): 13,733,163, type of input current: three-phase, input voltage: 400 V, Equipment: documentation/manual, MAN Roland 50-5 HiPrint five-colour B3 sheetfed offset press, manufactured in 2009. The press is equipped with a control console, connected densitometer and CIP3 system, including the required hardware keys. This configuration offers efficient colour pre-setting and colour control, making the machine suitable for high-quality commercial printing, brochures, leaflets, labels, packaging-related work, and demanding short- and medium-run offset production. The machine has a low total sheet count for its age: approximately 13.7 million impressions. Main technical data: Max. sheet size: 360 × 520 mm Min. sheet size: 148 × 180 mm Max. image area: 350 × 515 mm Printing plate size: 459 × 525 mm Blanket size: 530 × 540 mm Stock thickness: 0.04 – 0.8 mm Printing start: 52 mm Max. speed: 13,000 sheets/hour Frequency: 50 Hz Software language: German Equipment and extras: ProfitPlus Comfort Electronic double-sheet detection Ultrasound double-sheet control at the feeder Blanket washing device with cloth / indirect washing Automatic ink roller wash-up device ATwash cloth system Dosing unit alpha.d Alcosmart alcohol stabilizer Additive dosing unit Carton guide complete with vacuum feed board EPL semi-automatic plate change system Venturi Air Transfer system Technotrans cooling and circulation system with automix device Weko T6 / Grafix 72 Digital Plus powder sprayer Grapho-Metronic register system PQC Plate thickness: 0.15 mm Special value-enhancing extras: manroland control console with monitor and ink-key control CIP3 system with hardware keys Connected densitometer for precise colour control Double-diameter impression cylinders High impression force, suitable for thicker stock and carton work Documentation, installation CDs, spare parts and tools included Counters: Total impressions: approx. 14 million Operating hours: approx. 8,363 hours Inspection and service: The machine has been inspected by Man Roland service in Hungary. It is currently installed in our printing house and can be inspected by appointment in Budapest, Hungary. Redpfx Aozbyncsb Eocd Advantages and applications: The press is suitable for high-quality commercial printing, brochures, leaflets, labels, forms, packaging-related work and other demanding offset printing applications. Thanks to the double-diameter impression cylinders and high impression force, the machine is also suitable for thicker stock and carton printing up to 0.8 mm. Condition: used, installed, available for inspection Location: Budapest, Hungary Terms: ex works Budapest

Condition: new, Year of construction: 2022, functionality: fully functional, TAKAMAZ CNC Compact loader FC60 Lathe with automatic loader unloader quickest loading system in the world loading time new part 2,8 sec. loading cap. till 60 mm diameter. loading lenght max 50 mm max weight 1 kg per side loading feed 120 m min include part turning for loading Fanuc Control full warranty 2 year Lathe spec. Spindle motor 7,5/5,5 kw turning diameter max 180 mm turning lenght 240 mm bar cap. 35 mm collet chuck 173E till 40 mm diameter spindle nose A2-5 spindle speed 4500 rpm tool pos 8 stations tool shank 20x20 mm boring holder 25 mm diameter Rcjdem E I D Hepfx Ab Eod rapid speed X/Z 18/24 meter machine dimension 1,36 x 1,37 meter height 1,7 meter weight 2,7 ton total power 14 KVA Price is EXW (Stock Europe), Include loaded on truck. Transport, installation, commissioning, training, and yearly service contracts are available upon request for an additional fee. Installation and training is always done by our high qualified Service team in 3 locations in Europe. Netherlands, Germany, Romania.

Year of construction: 2009, condition: like new (used), Press with container Engine 5,5 kW 400 V Rjdpfxjfhb Tie Ab Ejcd