Thread rolling machine

ORT RP18

Condition: used, ORT RP18B overhauled Hodsuua H Rspfx Ad Ren

Condition: used, functionality: fully functional, machine/vehicle number: D20E/8022, Offer Number: D20E/8022 Machinetype: multiple wire drawing machine - dry Info: straight through Make: VEB Hjdpfx Aowi Tidsd Rsn Type: 8 Block Constr. year: inlet wire diameter: 2,5 mm finished wire diamter: 0,8 mm number of drafts: 8 diameter of capstan: 400 mm speed -meters/sek: 15 m Location: Europe

Condition: refurbished (used), Thread rolling machine ORT RP18 B 2-roll Hjdpfx Ajvxa Dbsd Rjn overhauled See video The machine is in our warehouse in Gussago BS, under power Test run possible Mimu Machine Tools Italy Power (Ton): 18 Number of rollers: 2

Condition: refurbished (used), Thread rolling machine ORT RP18 B 2-roll overhauled Hsdpfxswwmiyj Ad Ron LOW PRICE The machine is in our warehouse in Gussago BS, under power Test run possible Mimu Machine Tools Italy Power (Ton): 18 Number of rollers: 2

Condition: used, Year of construction: 2001, pressure 0,2-40 t max. workpiece diameter 70 mm Hjdpfxst Hw N To Ad Rjn threading length 120 mm Control total power requirement 29 kW weight of the machine ca. 9,5 t dimensions of the machine ca. m

Condition: used, Thread rolling machine ORT RP18 2-roll Spindles diameter 69.95mm See video The machine is in our warehouse in Gussago BS, under power Test run possible Mimu Machine Tools Italy Power (Ton): 18 Hjdpfx Ast Apuged Rjn Number of rollers: 2

Condition: used, Year of construction: 2007, Manufacturer: ORT Model: RP18 Year : 2007 Maximum rolling thrust 18 Ton Roller shaft diameter 54 mm Roller shaft key 12 mm Minimum diameter workpiece to rolled 3 mm Hsdpfjv Tqdbjx Ad Ren Maximum diameter workpiece to be rolled 60 mm Max.length workpiece rolled in plunge-feed 175 mm Max.length workpiece to rolled in enfilade — Maximum Pitch workpiece to be rolled 4 mm Maximum roller diameter 185 mm Main motor power 7,5 HP Total installed power 11 HP Maximum noise level 80 db Net weight 1800 kg Height Rolling shaft from the floor 1035 mm Machine width 1450 mm Standard machine depth 900 mm Total machine height 1800 mm

Condition: ready for operation (used), Romanian Forging Hammer CM 2500 (The hammer is similar to Huta Zygmunt MPM 6300B) - Maximum impact energy at full stroke: 7000 kgm - Ram weight: 2500 kg - Mode of operation: pneumatic - Ram stroke: 850 mm - Number of blows per minute: 100 - Working pressure: 5–7 bar - Anvil weight: 48 t - Total weight: 65 t Romanian Forging Hammer CM 1250 (The hammer is similar to Huta Zygmunt MPM 3150B) - Maximum impact energy at full stroke: 3600 kgm - Ram weight: 1250 kg - Mode of operation: pneumatic Hjdpew Sdxasfx Ad Rsn - Table size (front to back): 700 mm - Stroke: 800 mm - Number of blows per minute: 110 - Working pressure: 5–7 bar - Max. upper die weight: 400 kg - Die height: 220 mm - Ram (front to back): 500 mm - Air consumption: 15 m³/min - Anvil weight: 24 t - Height of machine above floor: 3750 mm - Total machine height: 4380 mm - Total weight: 35 t

Condition: used, Thread Rolling Machine, Cold Rolling Machine, Thread Rolling Machine, Profile Rolling Machine Manufacturer: PEE-WEE Model: UPW 24 Serial No.: P07 Year of manufacture: 2007 Maximum rolling force: 24 tons Maximum tool diameter: 270 mm Roll spindle diameter: 69.85 mm Tool bore diameter: 70 mm (nominal diameter) Maximum tool/reception length: 180 mm Maximum workpiece diameter: 50 mm Hydraulic motor power: 3 kW Roll drive motor power: approx. 5.5 kW Electrical connection: 400 Volt, 50 Hz, 10 kW - Pivotable roll spindle for through-feed thread rolling - Roll spindle speed adjustable in 4 steps via gearbox shift - Hydraulic unit integrated in the machine base - Operating manual with electrical schematic Hodpfx Asuz If Nod Rjn Space requirements (L x W x H): 2,000 x 1,450 x 1,900 mm Weight: approx. 3 tons Very good condition Plunge Rolling: The thread rolling tools, having the same pitch as the workpiece, form the thread by penetrating the workpiece up to the nominal diameter. The maximum thread length is limited to the width of the rolling dies. Through-feed Rolling: Used when the thread length is greater than the width of the rolling dies. Through-feed tools are divided into three sections – entry, calibration, and exit. Knurling rolls have no pitch and are swiveled at the lead angle corresponding to that of the profile to be rolled. Lead angle rolls differ from knurling rolls by having a pitch in the profile. The sum of the lead angle and swivel angle results in the effective lead angle in the workpiece.

Condition: good (used), 1 used single-sided press Make: SACK & KIESSELBACH, year of construction: 1962,74 serial number 31900 Pressing force 630 t, stroke 310 mm Installation height 320 mm Working height 1200 mm Hjdpfxeul U Svj Ad Rsn Drive power 10 KW