Magnetic belt chip conveyor

Neuhäuser 2126-3

Condition: good (used), Year of construction: 1993, machine/vehicle number: 28794, Offer 24419 Chodpfxjuk D I Rj Ap Ded Technical data: - Roller diameter 520 mm - projection 510 mm - max. passage height 420 mm - Table size 750 x 800 mm - Table swivels left + right 15 / 30 ° - Table height from floor 1020 mm - Saw blade length 4120 - 4200 mm - saw blade width 20 - 25 mm - infinitely variable cutting speed - level 1 18 - 160 m/min - Stage 2 240 - 2280 m/min - Pneumatic connection 6 bar - Drive 400 V / 5.5 kW - Weight approx. 1100 kg - Space requirement approx. W 1200 x H 2200 x D 900 mm - with: - table feed - Saw blade welding unit in the machine stand - Grinding stone - Shears + air pump - lighting

Condition: excellent (used), Spot welding machine with single-acting cylinder and flange-mounted electrode holders above and below Make: DALEX Type: PMS 14-3 Throat depth: 350 mm Rated power at 50% duty cycle: 80 kVA Secondary short-circuit current: 54.5 kA Secondary open circuit voltage: 7-14 V Electrode force: 80-1,200 daN Equipped with: 8-step switch Main switch Attached control cabinet HARMS+WENDE Synchronous welding control MPS 200 8 welding programs with AEG nameplate Start via foot pedal Codpfxjtuwz Ij Ap Dehd

Condition: new, Year of construction: 2026, Drum chipper series ATH-220/530/3 | ATH-220/730/3 | ATH-220/1060/3 S&F chippers and drum chippers with horizontal infeed are used in many areas of the wood processing industry (sawmills, timber mills). Chippers from the ‘ATH’ series produce high-quality and homogeneous wood chips with a low proportion of fines from residual wood, for example as quality chips for the cellulose industry or as fuel chips for energy generation Cedpfxewbv Ero Ap Djhd Series ATH-220/530/3 | ATH-220/730/3 | ATH-220/1060/3 - Feed height: 200 mm - Feed width: 500 | 700 | 1000 mm - Number of chipper knives: 2 - 4 pieces - Number of counter knives: 2 pieces - Rotor diameter:520 mm - Number of feed rollers: 3 pieces - Throughput: up to approx. 40 rm/h * - Chipping length: 5 - 50 mm - Chipper drive power: 22 - 110 kW - Drive power feed rollers: 2 x 2.2 kW - Operating/control voltage: 400/220 V, 50 Hz - Weight: 2,800 - 4,000 kg *depending on chipper length, kW main motor, number of knives, feed Advantages: - Maximum throughput - Low fines content - Low maintenance - Flexible use - Customised production

Year of construction: 2017, condition: like new (used), 2D Wire Bending Machime Codpomqk Tpofx Ap Dehd Year - 2017 Manufacturer - VIBRA Wire diameter - 1-4 mm Capacity - 30pieces/ min Power - 3,5 kw

Year of construction: 2021, condition: new, Aluminum angled conveyor belt including mobile substructure horizontal area 1500mm (adjustable) Rising range 2500mm (customizable) Freely selectable angle in the bend: 30, 35, 40 or 45 ° Polyamide swivel castors with locking brakes Conveyor belt width 400mm (adjustable) We deliver our conveyor belts in PVC, PU or rubber. PVC conveyor belt including carrier and corrugated edge Drive: Motor 0.25KW (adjustable), speed 0.3m / sec Connection 220 / 240V, 50Hz, protection class IP54 Drive etc. ready for connection, motor control optional 6x adjustable machine feet for alignment Wave edge: 40x35mm (customizable) T-20 studs - 400mm pitch (customizable) 2-ply particularly cross-stable Our core competence lies in delivering exactly what the customer really needs. We work together with our customers to develop customer-specific, individual solutions and deliver corresponding systems from our own production. B2hd9kmmdn Feel free to contact us by phone to find a suitable solution for your application. Csdpjhh A U Hefx Ap Dohd Conveyor belt, conveyor belt system, discharge belts, belt conveyor, magnetic separator, overbelt magnetic separator, recycling, wood chips, plastic, metal-free metal detection, neodymium, overbelt magnet, magnetic belt separator

Condition: refurbished (used), Year of construction: 2009, functionality: fully functional, total height: 8,025 mm, total width: 3,405 mm, total length: 2,810 mm, load capacity per storage section: 250 kg, construction height: 50 mm, warranty duration: 12 months, Equipment: safety light barrier, Table preselection control with article management. Device comes from a lift system. Side shaft claddings have been retrofitted. No side access door. 4 units available. Machine height is adjustable. Storage lift including delivery, installation, DGUV acceptance & warranty. Chsdpsw S Udyefx Ap Dsd

Condition: refurbished (used), Year of construction: 2007, functionality: fully functional, total height: 6,000 mm, total width: 1,750 mm, total length: 2,820 mm, load capacity per storage section: 500 kg, construction width: 1,300 mm, warranty duration: 12 months, – Tabular control panel with item management – Unit comes from a lift system – Side lift shaft cladding reproduced – 2 units available – 1300x825mm tabular panel, 500kg payload each Chsdpfszaqibex Ap Djd

Condition: used, Tool presetting machine GILDEMEISTER-DE VLIEG, type EGS 5045 / Microset DPS 100 Codpfx Aehbal Dep Dshd Serial No. 83-10-102, Year of manufacture 2002 Travel X-axis: approx. 400 mm Travel Z-axis: approx. 400 mm Tool holder in the mounted rotary table: Ø 50 mm Pitch circle diameter of the tool holders in the mounted rotary table: Ø 340 mm Internal taper in the mounted rotary table: Ø 245 mm Tool holder plate as a rotary table with 8 mounting holes Ø 50 mm Centering diameter of the mounted tool holder plate: Ø 102 mm Rotatably mounted flange with centering diameter: Ø 102 mm Rotatably mounted flange with outer diameter: Ø 155 mm Rotatably mounted flange with 3x M10 mounting holes, pitch circle: Ø 130 mm Mains connection: 230 volts, 50 Hz - Measuring electronics Microset DPS 100 - Rotary table with 8 tool positions - Interfaces: 1x RS232, 2x measuring system (X/Z) - Profile projector with screen Ø 100 mm, magnification 20x and two circle ground glass screens - Ground glass screen fixed with crosshair - Axis movement via manual quick adjustment with pneumatic clamping - Fine adjustment via handwheels - Rotatable rotary table with pneumatic clamping - Metal base with 3 drawers Footprint L x W x H: 1100 x 1000 x 800 mm Weight: 400 kg Good condition

Condition: used, Year of construction: 1971, roll diameter / mm throat / mm workpiece height / mm table-size 800x750 mm Technical specifications: Roll diameter approx. 420mm Projection in width approx. 415mm Projection in height approx. 265mm Table size approx. 605 x 600 mm Belt speed 18 - 562 m/min. 8 levels Saw band length min./max. 3150 / 3260mm - Saw band speed over 4 gear stages and 2 engine speeds Chedpfxjwgi R So Ap Dod - Saw blade butt welder IDEAL BS 0-16 with scissors and whetstone - swiveling work table in 2 axes Dimensions: approx. L x W x H 950 mm x 750 mm x 1900 mm Weight 600kg with table feed Description has been adopted.

Condition: new, Year of construction: 2024, pressure 30 t throat 180 mm stroke 8-76 mm Chjdpfx Apjvfhq Aj Djd no. of strokes 80-200 Hub/min ram - range of adjustment 60 mm table surface area 360x580 mm table height 840 mm hole in the table Ø 110 mm ram surface 250x350 mm tool hole in ram Ø 40 mm total power requirement 3 kW weight of the machine ca. 1,8 t dimensions of the machine ca. BxTxH 1350x1200x2100 mm