Used Weinig Unicontrol 5 for sale (536)

Condition: as good as new (ex-display), Please check in your junk mail if you do not receive a reply within 24hrs from sending your inquiry !!! CAN SHARPEN MAX 406MM DIAMETER CUTTERS !!! The G-716 Semi-automatic Cutterhead Grinder is used to sharpen 178mm to 406mm diameter eased edge, milled to pattern, and fingerjoint cutterheads. Worktable traversing is automatic and has adjustable stops. Cutterhead indexing is manual. Each knife is held against a positive stop while being ground !!! No Index Plate To Change No index plate to change when working with heads with different numbers of knives. The use of an index plate assumes that the knives and head separations are uniform throughout, which is often not the case. If the height of the knife is high or low, then the front face of the knife will vary from knife to knife making the task of grinding difficult. The one constant is the back face of the knife, therefore the use of an indexing stop against the back face will provide for accurate indexing regardless of the irregularities in the knives and head slots. Head Indexing and Wheel Feed: Manual Minimum / Maximum Diameter Cutterhead: 7″ Min./16″Max. 178mm Min./ 406mm Max. Fjdjq Dzi Topfx Aivspn Worktable Feed: Air / Oil Travel (maximum): 12″ 305mm. Adjustable Limits: Proximity Switch Speed: Fully Adjustable Index Method: Manual index after each knife is ground. Grinding Spindle: 1-1/2 HP Wash Down Duty TEFC Motor 3600 RPM, Dual ABEC 7 Precision Bearings, with Sealed Lubrication. 8″ (203mm)Diameter Grinding Wheel (9″ 229mm Diameter Max.) Coolant System: 15 Gallon Tank with Casters, Sediment Tray Full View Sight Glass, 5 GPM Pump (120VAC) Wash Down Hose Included Specifications Grinds 7″ to 16″ diameter eased edge, milled to pattern, and finger joint heads Automatic traversing worktable with adjustable travel limits Manual indexing of knives against a positive stop with grinding position pneumatic brake allowing precision indexing without the need of an index plate High precision 1-1/2 HP grinding spindle with sealed lubrication Recirculating adjustable flow flooded coolant system with wash down hose Fully enclosed grinding chamber with viewing windows and task light Grinding wheel feed allows unattended operation. New Proscale.

Condition: used, Weinig Unimat 23 Technical data Working width 30 - 230 mm working height 19 - 200 mm elevated on pedestal u- re-li-o-u.o Fjdpfxjncc Igs Aivjpn without feeder only machine machine is dismantled, immediately available Transport can be organized

Condition: used, Weinig brand moulding machine, Unimat U17N model with 7+1 axes, 170 mm axis length, with ruled table, cardan shaft drive. Fodpfx Aopfp Eljivspn Axle composition: Bottom, right, left, right, top, bottom, left, universal. Axle motor power: 4+4+5.5+5.5+7.5+5.5+5.5+7.5 Kw. Towing motor power 4 Kw raises and lowers 0.75 Kw.

Year of construction: 1998, condition: excellent (used), I sell the window profiling automat centre Weinig Univar 10 Fpsdpfofzzhrox Aivsn Year 1998. Moulding heads OERTLI. Available immediately. Unit price 8.500 euro. 4 pcs. available. Condition very good !

Condition: excellent (used), Four-sided planer Weinig Profimat 22 N, 6 heads – the last one is universal. Tools included. Work video of the machine available. Very good condition. Ready for operation. Fedpsxyxaasfx Aivopn

Condition: reconditioned (used), Year of construction: 1997, functionality: fully functional, machine/vehicle number: 226-60758, Number of spindles: 5 units Working width: 230 mm Planing height: 120 mm Feed motor: 2.2 kW Fedpfxsw Svb To Aivopn Feed speed: 5–24 m/min Total power requirement: 25 kW Dimensions (Length/Width/Height): 3400 x 1800 x 1610 mm Machine weight: approx. 2500 kg Four-Side Planer WEINIG PROFIMAT 23 E - Year of manufacture: 1997 - Serial number: 226-60758 - Maximum working width: 230 mm - Maximum working height: 120 mm - Cardan shaft feed, stepless adjustment 5–24 m/min - Feed motor: 2.2 kW - 1st spindle (bottom): 4.0 kW - 2nd spindle (right) – motor for 2nd right and 3rd left spindle: 7.5 kW - 3rd spindle (left) - 4th spindle (top), motor: 5.5 kW - 5th spindle (bottom), motor: 4.0 kW - Electrically adjustable height and depth: 0.25 kW - All spindles equipped with brake motors - Spindle speed: 6,000 rpm - Spindle diameter: ø 40 mm - Planing table: 2,000 mm with serrated table inserts and straightening guide - Feed rollers with pneumatic pressure - Feed roller diameter: 140 mm - Transport rollers opposite left spindle - Infeed roller before jointer with pneumatic actuation - SICO counters - Manual wax pump - Centralized lubrication points - 1 set of planing heads - Total connected load: 25 kW - Machine dimensions: L=3400 mm, W=1800 mm, H=1610 mm - Weight: 2500 kg

Condition: excellent (used), Weinig 140/4A Four-Side Planer Working width: 140 mm Working height: Number of spindles: 6 Spindle arrangement: Bottom 3 kW Right 2.2 kW Top 3 kW Bottom 3 kW Right 4 kW Left 3 kW Feed speed adjustable: First gear 4.3/5.3/14.5/18 m/min Second gear 8.6/10.6/29.0/36.0 m/min Fpjdpow Tiyxjfx Aivjn Total power: 21 kW

Condition: excellent (used), Working width: 30 cm Working height: 46 cm Wheel diameter: 1.1 m Fsdpswy Ruxsfx Aivepn

Condition: used, Weinig Profimat 23 automatic planing and moulding machine for four-sided planing and profiling of timber, with a mobile spindle. Technical data: - Spindles: 5 - Spindle 1: Bottom / 5.5 kW / 40 mm - Spindle 2: Right / 5.5 kW / 40 mm Fedpfx Aiex Ecguevjpn - Spindle 3: Left / shared motor with #2 / 40 mm - Spindle 4: Top / 7.5 kW / 40 mm - Spindle 5: Bottom / 4 kW / 40 mm - Working width: 230 mm - Working height: 120 mm

Condition: used, Stehle HK 630 (semi-automatic straight knife grinder). Specification: • Maximum tool width 630 mm !!! • Tool diameter planer heads (min-max knife heads) 120 - 340 mm • Grinding wheel spindle speed 2850 rpm • Grinding wheel drive 1,1 kW • Clearance angle 10 - 35° • Coolant tank 28 L • Motor coolant pump 0,28 kW Fedpfxjv T Rkho Aivspn • Connection values, total 2 kW Please check in your junk mail if you do not receive a reply within 24hrs from sending your inquiry !!!

Condition: excellent (used), High speed moulder infeed comprising a freestanding flat magazine in front of a high speed moulder. The infeed magazine is driven by hydraulic motors powered by an 5.5kW hydraulic unit (max 140m/min). A buffer of feedstock is alligned laying flat side by side on the chain cross feeder. The chain feeder transports parts across to the fence. The part next to the fence is detected by a light beam and the the first roller is raised to allow entry and the transport roller then pushes the workpiece under the feed rollers of the planer. The first feed roller of the planer needs to be freewheeling roller to allow operation of the EM814. Fpjdpfx Aiewgbxzevsn

Condition: good (used), Year of construction: 1981, Chain width: 340 mm Cutting height: 200 mm 2 x 45 kW motors Shaft diameter: 65 mm Electric height adjustment Feed speed variably adjustable via frequency inverter Includes an additional 3 saw bushings and many spacer rings Fsdjxiu Dmspfx Aivepn Still ready for demonstration in a small business; technically flawless condition, but has not been in use for quite some time

Condition: excellent (used), Compact High Speed Planing Line Mechanisation with Stacker 1. Weinig EM814 moulder infeed with flat chain feeder Fodpfjxb U Txsx Aivepn 2. Weinig 820 high speed right angle moulder outfeed with cross feed sweepers 3. Weinig 811 board stacker with scissors lift (chain feed discharge options) -Boards are automatically transported laterally with the Weinig 820 right angle transfer. -Boards automatically form a layer and are then placed on the lifting table of the chain conveyor -The completed pack is transferred to the following chain conveyor -Maximum output: 40 cycles/minute for stacker (over 150m/min based on average length boards). -Space required: Length approx. 8000 mm, Width approx. 5000 mm approximately -Pack size max 6100mm x 1200mm x 1200mm(high) 3. Weinig cross chains after scissors lift to move full packs away from the stacker when full. Possible to supply with Weinig Hydromat moulders 100m/min as needed.

Condition: excellent (used), WEINIG Hydromat H23 Line, S/N 87321, year 1999, Ref-No. 103437 WEINIG Cross Conveyor HighMech E-1, equipped with 6 flat chains approx. 2000 x 3500 mm Hydraulic WEINIG Accelerator Model 814 Short infeed table with heavy-duty 4-roller feed unit Planer/moulder with reinforced KASCHWIG three-sided soundproof enclosure • Max. working width: 230 mm • Max. working height: 160 mm • Electronic feed, frequency-controlled, 8–80 m/min • Feed motor 18.5 kW • 1st spindle bottom 11.0 kW • 2nd spindle right 11.0 kW • 3rd spindle left 11.0 kW • 4th spindle right 11.0 kW • 5th spindle left 11.0 kW • 6th spindle top 15.0 kW Fedowvqklopfx Aivepn • 7th spindle bottom 11.0 kW • 8th spindle top 15.0 kW • 9th spindle bottom 15.0 kW • 10th universal spindle 11.0 kW (four-sided) • Spindle speed 6,000 rpm • Spindle diameter ø 50 mm • All spindle motors equipped with NEW motor start/stop brake units • Pneumatically supported top pressure rollers • Feed rollers D=140 mm • 6 driven rollers in the table • Spindles 1 + 6 + 7 + 8 + 9 with counter bearings • Spindles 8 + 9 with straight jointer • Spindles 8 + 9 with profile jointer • Spindles 6 + 8 with pneumatic pressure • Reduced spacing between feed rollers • Hard-chromed table plates • Hard-chromed fences • Pneumatically supported side pressure rollers • Automatic table lubrication • Centralized lubrication points • Free-standing control panel • Connected load approx. 145 kW / approx. 400 A • Free-standing electrical cabinet • Operating instructions, spare parts list and wiring diagram included • Machine sold without cutterheads Machine dimensions approx.: • Length: 6,000 mm • Width: 2,250 mm • Height: 1,800 mm • Weight: approx. 8,500 kg Factory-new WEINIG components installed: NEW horizontal/vertical spindle NEW counter bearings All spindles with HL bearings All motors newly fitted NEW electronic motor soft start/brake devices NEW hard-chromed table plates NEW hard-chromed fences Many other new parts fitted in the machine Condition: see attached photos – technically in excellent condition Infeed mechanization unrefurbished – complete – fully functional Payment: Net cash before loading Delivery time: By arrangement Delivery: EXW Inspection: Anytime by appointment Errors and prior sale excepted.

Condition: excellent (used), Year of construction: 2005, We offer a Weinig Super 4 planer in very good condition with EM 15 feed unit, year of manufacture 2005. Manufacturer: Weinig Model: Super 4 Year of manufacture: 2005 Condition: very good Type: planer Fpsdpfeylagmsx Aivjn If you have any questions or need further information, please send us a message or contact us by phone.

Condition: excellent (used), Year of construction: 2012, Weinig H1000 moulder with E3 infeed and A3 outfeed mechanisation Weinig Hydromat 1000 with 5 Spindles. (Year 2012) Fpedox Rbkxopfx Aivjn Separate electrical panel Separate remote control panel Automatic lubrication system for bedplates Memory system Full sound enclosure Weinig E3 moulder infeed +pack scissors lift (3000kg). Weinig A3 drop leaf outfeed + pack scissors lift (3000kg) + pack outfeed chain conveyor. WEINIG HYDROMAT 1000 230X160mm maximum dimension No 1. 7.5kw - Bottom 6000rpm + Outboard bearing + Straight jointer No 2. 7.5kw - Right 6000rpm + profile jointer No 3. 7.5kw - Left 6000rpm + profile jointer No 4 . 7.5kw - Top 6000rpm + Outboard bearing + Straight jointer No 5 . 7.5kw - Bottom 6000rpm + Outboard bearing + Straight jointer 50mm spindles Beam 0.55kW Full documentation included. Extraction manifold included. POSSIBLE TO PURCHASE MOULDER OR MECHANISATION SEPARATELY AS NEEDED

Condition: excellent (used), Weinig four-side planer Fpedpfx Aex E Rzpjiven

Condition: excellent (used), functionality: fully functional, Four-sided planer Weinig Profimat 26 Fortec + EM11 Working width: 230 mm Working height: 130 mm Number of spindles: 5 Spindle arrangement: Bottom 5.5 kW Left Right 11 kW Top 7.5 kW Fpjdpfx Aisyn Et Reven Bottom 5.5 kW Material feeder: Weinig EM 11 Pneumatic pressure rollers divided into 3 sections Feed speed adjustable via frequency inverter: 5–24 m/min CE certificate Technical documentation

Condition: excellent (used), Weinig Powermat 400 four-sided planer max. planing width: 230mm max. planing height: 160mm 6 heads 2 vertical heads with powerlock 2 final horizontal heads with powerlock Spindle 1 - 7.5KW Spindle 2-3 - 11KW Spindle 4 - 11KW Spindle 5 - 11KW Spindle 6 - 7.5KW Powercom control system Fjdpezg Axgjfx Aivepn 40mm spindles feed rate via inverter, adjustment range: 5-30m/min Robust planer from WEINIG, machine inspected, well-maintained, in very good condition.

Condition: excellent (used), Year of construction: 2004, Weinig Hydro fine planing machine, Uniplan 23 Year of manufacture: 2004 Fsdpfxozg Euqo Aivspn Working width: 230 mm Working height: 120 mm 1st spindle, bottom: 7.5 kW 2nd spindle, top: 7.5 kW

Condition: used, Year of construction: 2008, WEINIG OptiControl 970090 tool measuring station, net price €7,650 Specifications: Fsdpfozvpw Isx Aivepn Tool diameter min. 90 Tool diameter max. 300 mm Tool length 0 - 240 mm Radial measuring range (radius) 150 mm Non-contact measurement of tool dimensions, radius (R) and height (H), with display on electronic digital displays. Electronic digital displays providing information on tool radius and height. HSK63 tool holder for PowerLock tools. NEW: PowerLock adapter HSK63, shank D=50 x 260 mm.

Condition: excellent (used), functionality: fully functional, spindle diameter: 40 mm, spindle speed (min.): 6,000 rpm, working width 230mm working height 140mm 6 spindles spindles set: bottom/right/left/right/top/bottom Fjdpey N N S Uofx Aivepn spindles diameter 40mm variable regulated feeder electric adjustment of infeed fence electric adjustment of infeed table ATS fast locking spindle system

Condition: good (used), Year of construction: 1981, For inquiries: Fpjdpfx Aioy Nmv Devon Zoltán Utasi Plus 36 30 205 7380 pindle configuration: Bottom Right Left Top Bottom Spindle speed: 6000 rpm Working width: 170 mm Working height: 120 mm Jointing table length: 2 m Equipped with Waxilit pump Infinitely variable feed speed: 7–18 m/min Side pressure roller Motorized pressure beam adjustment Equipped with 5 cutter heads (3 pcs L180 mm, 2 pcs L130 mm) Machine documentation available

Condition: excellent (used), Year of construction: 2009, functionality: fully functional, Weinig Dimter Profipress C 2800 P - 6 m gluing press Manufacturer: Weinig Dimter Model: Profipress C 2800 P - 6 m Year of manufacture: 2009 Condition: Very good Machine description: For sale: Weinig Dimter Profipress C 2800 P - 6 m wood gluing press, year 2009, designed for the production of glued wooden panels and elements made of soft timber. The machine was developed for efficient production using PVAC glue in D2 / D3 class and allows processing of material within specified width, thickness and input length ranges. According to the documentation, this model can process timber with widths from 30 to 80 mm, thicknesses from 15 to 40 mm and input lengths from 2100 to 2800 mm. The machine allows the production of panels with variable widths from 600 to 1200 mm. For short lengths, the collecting distance range is 700 to 1400 mm. The output is up to 10 to 15 infeeds per minute, depending on the entrance width. The Profipress C 2800 P - 6 m is intended for processing soft timber. The permitted bending tolerance is maximum 5 mm per meter. The documentation also specifies recommended operating conditions, including room temperature from 15 to 30 degrees Celsius and air humidity in the range of 40 to 65 percent. Technical data: - Model: Profipress C 2800 P - 6 m - Year of manufacture: 2009 - Performance: max. 10–15 infeeds/min, depending on entrance width - Timber width: 30–80 mm - Timber thickness: 15–40 mm - Timber entrance length: 2100–2800 mm - Collecting distance for short lengths: 700–1400 mm - Panel width: 600–1200 mm - Timber type: soft timber - Permitted bending: max. 5 mm/m - Glue type: PVAC D2 / D3 Fpsdpfxoyvgiao Aiven - Recommended room temperature: 15–30°C - Recommended air humidity: 40–65% Features and advantages: - Press designed for glued panel production - Machine from the renowned Weinig Dimter brand - Output up to 10–15 infeeds per minute - Possibility to produce panels with variable width - Suitable for processing soft timber - Works with common PVAC D2 / D3 glue - Industrial application for woodworking and production plants

Condition: used, Year of construction: 1986, used, good condition, low hours Brand: Weinig Model: P22N Year of manufacture: 1986 Machine no.: 226-670 Number of spindles: 4 Spindle arrangement: bottom - right - left - top Motor power kW: 4.0 - 7.5 4.0 Motor brakes Planing width approx. mm: 220 Planing height approx. mm: 120 Spindle diameter mm: 40 Table length approx. mm: 2,000 Pre-cutter Cardan feed Lateral pressure rollers Protective hood Infeed before the jointer Infinitely variable feed speed 4 - 20 m/min Profiling Sliding rollers: 1 piece Electric adjustment: thicknessing shaft Digital displays: width-height Extraction connection mm: 120/120/120/140 Space requirement approx. 3600 x 1400 x 1400 mm Fodpfjy Apfzjx Aivopn Weight approx. 1,500 kg Location: 97447 Gerolzhofen, free loaded, unpacked Delivery in current condition, as inspected, without any warranty or guarantee