Used Transfer Press for sale (15,270)

Condition: used, Year of construction: 2005, functionality: fully functional, Clamping force: 4900 kN Working pressure: 206 bar Heating plate dimensions: 700 x 700 mm diameter of piston: 558,8 mm max. stroke: 250 mm Fpjdpfx Ahsztda Ssmek daylight: 300 mm max. mass of heating plant: 560 kg capacity of oil tank: 1100 l rated capacity: 82 kW heating capacity: 56 kW enginge output, vacuum motor: 4 kW Stroke of vacuum cover: 200 mm dimensions: 3975 x 2935 x 2555 mmm Equipped with a crane runway (monorail) with three chain hoists Producer: STHAL Year: 2011 Lifting capacity: 3 x 400 kg Lenght of crane runway: ca. 3500 mm Rolling chassis Lifting capacity: 400 kg Lifting height: 3000 mm stroke speed - main stroke: 4 m/min stroke speed - fine stroke: 1 m/min The vulcanizing press from manufacturer PAN STONE, was used by a renowned German company specializing in sealing technology and electromobility. This company is known for its high quality and innovation in seal production. It was always professionally maintained and repaired, which explains its excellent condition. This press offers you the opportunity to invest in proven technology that was utilized by a leading company in Germany.

Condition: good (used), Year of construction: 1994, Clamping Unit: Clamping force: 7,000 kN Operating pressure: 250 bar Specific pressing pressure: 610 N/cm² Number of levels: 2 Installation height with 75 mm heating plate & 20 mm insulating plate: approx. 2x 190 mm Piston stroke: approx. 400 mm Piston 1 diameter: 543 mm Clamping force, rapid traverse: approx. 2 x 85 kN Retraction force: approx. 2 x 47 kN Operating pressure: 300 bar Piston 2 diameter: 60/40 mm Stroke: 400 mm Estimated weight: approx. 16 tonnes Hydraulic System: Pressure adjustment: 40 - 300 bar Flow rate regulation: 0 - 99 % Flow rate l/min (HD): 45 against 300 bar Drive power: 22 kW Tank dimensions (LxWxH): 1000 x 770 x 535 mm Closing Speed: Fpsdpeztda Esfx Ahmjk Rapid traverse: approx. 40 - 50 mm/s Slow closing: approx. 0 - 20 mm/s Pressing speed: approx. 0 - 3 mm/s Slow opening: approx. 0 - 20 mm/s Opening, rapid traverse: approx. 0 - 60 mm/s

Condition: good (used), Year of construction: 1997, functionality: fully functional, oil tank capacity: 220 l, pressure: 300 bar, ID43737 Year: 1991-1997 Press machines with capacities from 60 tons to 80 tons Brand: Hydro-Presses Fjdpfowhcmpsx Ahmspk 2 units with 60 ton force PH600 Hydraulic cylinder stroke: 600 mm Maximum hydraulic cylinder force: 60 tonnes at 300 bar 5 units with 80 ton force PH800 Hydraulic cylinder stroke: 600 mm Maximum hydraulic cylinder force: 80 tonnes at 300 bar

Condition: used, Three second-hand swivelling clamping shoes from Schafberger + Sprödhuber (S+S) for frame presses used in professional woodworking. They are used to align and securely clamp workpieces when assembling frames and structures. Fpjdpfx Ahoztniwsmek Technical data: - Dovetail width: ~ 58 mm

Condition: good (used), Refurbished machine *Options at additional cost, see below with a full 1 year warranty one machine is directly available Technical specifications: Throughput up to 1200 kg / h depending on the material (e.g. sawdust with a bulk weight of 150/180 kg / qbm) Briquette Ø 75 mm including 2 m press channel Main motor power 45 kW Feed screw gear motor 2 x 2.2 kw Compressor screw 2 x 5.5 kw Distribution auger 2.2 kw Hydraulic pump motor 0.37 kW Total connected load 65 KW Control panel with plain text display for operating states and utilization display for main drive and feed screws PLC control Siemens S7 / 300 with operating hours counter in the control cabinet Fpodpfxs E Dquj Ahmek Machine hat CE mark Automatic start / stop function of the machine Dimensions 3100x860x1800 mm lxwxh Weight 4500 kg Options: -Silo for MAP series Storage silo above the machine - Contents approx. 6 square meters, stable steel construction with agitator discharge and level indicator. 19,700 € net plus VAT. *only possible for one presse MAP 1200 below the silo if you need to place two machines MAP 1200 below one silo it needs to be build completely different. the price for this silo is 37.900 € net -Temperature control device for the pressing tools to maintain the temperature for optimal briquette size. Temperature controller for pump, cooling unit, fan, pressostat Wired ready for connection - must be left for operation including corresponding control € 7.850 net Oil heater 1.950 € net -Guillotine, to cut the briquettes to length Create a compressed air connection on site € 6,940 net plus VAT -Transport line / cooling section (nominal value: 4x2m) 990 euros net per 2 meters - Control System 4.995 € net Assembly / commissioning (nominal value approx. 2-3 days on site to install one press) based on effort and upon proof against separate invoice. The following sentences apply: Service technician/mechatronics technician per assembly and hour of travel: €129.00 Overtime: 25% surcharge 50% surcharge per Saturday and night hour 100% surcharge for every Sunday and public holiday hour Release per fitter per day: country dependent Per car, van and driving kilometer: €0.98 / km Arrival and overnight stay against receipt or flat rate bill at the client's expense. . Test with the respective customer material: (up to a maximum of 750 kg) - €1,970 net flat rate --- Recognition from the raw material: - The moisture content must be between a minimum of 6 and a maximum of 18% - Maximum span 20 mm - Excessive temperature: temperate room at at least + 5 ° C. - The loading must be free of metals and mineral impurities. This and the pressing tools and / or responsible wear can be the result

Condition: new, Year of construction: 2025, High performance CNC press brake PETERZEN model MORICO 70065 6 axis + 2 + 1 Rigid S355 steel frame Workbench structure and Ram manufactured from laminated S355 steel Symetric renforced Throats Heavy grey cast iron slydways with automatic lubrication system CNC Controller CYBELEC VisiPac 8 axis + 1 Bosch Rexroth servo valves Inovance servo drive systems DIEMA high resolution glass scales for high bending precision Bending force 700T Bending lenght 6500 mm Distance between columns 5100 mm Depth throat 420 mm Ram stroke 400 mm Closing Ram approach speed limited to 30 mm/s for human operation Closing Ram working speed 7 mm/s Return-speed 40 mm/s Main hydraulic motor 45 kW Machine weight 62,000 kg 8 Axes + 1 CNC controller Cybelec VisiPac Touchscreen monitor with vivid colors and high contrast 3D graphical profile drawing (Touch Profile) and precise 2D program creation The opening value can be setted individually in each sequence Machine can be inferfaced with different CAM software Easy single bends with the EasyBend page Correction menu Many languages available Centered lower die system 60 mm AMADA / WILA- tool or COLLY Standard Ram featured with intermittant tool holder for punches with AMADA or COLLY Standard dimensions and Fall down security All toolings adopt 42CrMo4 steel, induction hardened and cnc grinded 4 Axis Back gauge adopts linear guides and Ballscrews Back gauge travel X axis 1000 mm 2 automatic widened back gauge fingers on linear guide rails with helical rack and pinions (Axis Z1 and Z2) Automatic height adjustment (Axis R) 2 CNC Bending Followers 400 kg up to 60° angle Motorised displacement of bending followers and parking area on the right of the bending table Strong automatic mechanical crowning table. The compensation value is calculated and set by the CNC system. Fodowd I Svepfx Ahmopk Safety Equipment : 3-position Foot switch with Emergency Stop Position Closing approaching speed limited to 30 mm/s for human operation Laser safety protection and permanent speed monitoring Closing bending (working) speed 7 mm/s Side covers with safety switch Rear-protection with sliding door and safety switch Low control Voltage (24V) Safety control unit category IV Standard configuration and equipment : Electric control cabinet on left side CNC user interface with Aluminium - arm 1 Line of punches (Upper tools) 85° R1, Height 200 mm 1 Line of centred lower Dies (to be defined) Place of manufacture : Douarnenez (Britanny) in Northwest FRANCE Customisation available CE Certification in respect of CE2006/42 directive and EN12622+A1 European Standard Operation manual in English, German and French language Delivery and Services available worldwide Customized Quotation GROW YOUR BUSINESS WITH PETERZEN MACHINE TOOLS

Condition: used, Year of construction: 1994, Used Machine Year of Manufacture: 1994 Features and Technical Specifications: - 21-spindle vertical boring mill - 3-spindle horizontal drilling machine - Pneumatic drilling feed - Pneumatic workpiece clamps - Pneumatic maintenance unit with pressure gauge and pressure regulator - Swiveling horizontal drilling unit with height adjustment - Adjustable side stops - Extension rulers on the left and right - Multiple adjustable stop blocks - Drilling depth adjustment - Mobile base with drawers - Comprehensive set of wood drill bits - Various stop gauges and adjustment aids - Protective shield on the vertical drilling unit - Vertical drilling unit: 21 drill spindles - Horizontal drilling unit: 3 drill spindles - Motor power: 1.1 kW - Power connection: 3 × 380 V / 50 Hz - Fuse rating: max. 6 A slow-blow - Compressed air: min. 5.5 bar - Air consumption: approx. 50 l/min - Max. operating pressure: 6 bar Fsdpfeztfudex Ahmepk - Machine table: 870 × 330 mm - Machine width without extension guide: 870 mm - Machine width with extension guide 1: 2,720 mm - Machine width with extension guide 2: 4,720 mm - Machine depth: 1,270 mm - Machine height: 750 mm (Dimensions without base) - Weight: 122 kg

Condition: like new (used), Year of construction: 2026, operating hours: 6 h, Actually one showroom machine available. Very robust machine with high pressing force - is also suitable for producing a salable briquette quality * depending on the material. The large press cylinder and the 80 mm briquette make this possible. Our best-selling briquetting press series + Tried and tested, simple technology, for extremely low susceptibility to errors + 25 years of experience, further development and know-how + Several thousand machines in use with satisfied customers + Top price-performance ratio Surcharge for cooling unit + € 4.995 net, (can also be retrofitted later) * cools the pressing tongs (important from 3.5 hours) and the hydraulic oil * Cooling device recommended for regular use of more than 3.5 hours at a time. Briquette diameter: 80 mm Front bush: 125 mm Briquette stroke max .: 100 mm Briquette lift opt ​​.: 80 mm Output (depending on material): up to 200 kg / h * * depending on the bulk weight * based on a bulk weight of 200 kg per cubic meter Motor power: 9.2 kW 400 volts / 50 Hz / 3 phases Length: 2095 mm Width: 1300 mm Height: 1700 mm Weight: 1250 kg Oil volume: 220 liters Silo diameter: 1200 mm Silo content: approx. 1 qbm Pump: 75 liters Hydraulic pre-compressor Cooling pressing tongs option: yes, with special accessory coolable pressing tongs Hydraulic oil cooling option: yes Cooling of the pressing tongs and the hydraulic oil with cooling device (special accessory) Fedpjxfwdefx Ahmjpk Level monitoring option: yes Strand briquette option; yes (depending on material) Option of enlarged filling slide: yes, with special accessory enlarged filling slide CE compliant . Requirements for the raw material: - The moisture content (atro) must be between a minimum of 6 and a maximum of 18% - Chip length maximum 20 mm - Installation temperature: temperature-controlled room at at least + 5 ° C - The loading must be free of metals and mineral impurities such as sand, stones, etc. This can result in damage to the pressing tools and / or increased wear

Condition: like new (used), Year of construction: 2026, Our best-selling briquetting press, the classic. + Tried and tested, simple technology for extremely low susceptibility to errors + 25 years of experience, further development and know-how + Several thousand machines in use with satisfied customers + Top price-performance ratio Options for an extra charge: * Surcharge for the level indicator that enables automatic operation + € 995 net * Surcharge for large pre-compression chamber + 980 € (recommended for light material like straw) Briquette diameter: 50 mm Front bush: 50 mm Briquette stroke max .: 40 mm Briquette lift opt ​​.: 40 mm Throughput (depending on material): 30-60 kg / h * * depending on the bulk weight * based on a bulk weight of 200 kg per cubic meter Fedpfx Ahsgl Nlmemjpk . Motor power: 5.5 kW 400 volts / 50 Hz / 3 phases Length: 1680 mm Width: 1100 mm Height: 1500 mm Weight: 680 kg Oil volume: 110 liters Silo diameter: 1000 mm Silo content: approx. 0.7 square meters Pump: 27 liters Hydraulic pre-compressor Option cooling pressing tongs: no Hydraulic oil cooling option: yes Level monitoring option: yes CE compliant . Requirements for the raw material: - The moisture content (atro) must be between a minimum of 6 and a maximum of 18% - Maximum chip length 15 mm - Installation temperature: temperature-controlled room at at least + 5 ° C - The customer must insure himself against loss of hydraulic oil - The loading must be free of metals and mineral impurities such as sand, stones, etc. This can result in damage to the pressing tools and / or increased wear

Condition: ready for operation (used), Year of construction: 2012, machine/vehicle number: 34368, functionality: fully functional, power: 15 kW (20.39 HP), input voltage: 400 V, input current: 40 A, input frequency: 50 Hz, type of input current: three-phase, pressing force: 170 t, stroke length: 200 mm, operating speed: 10 mm/s, reverse speed: 100 mm/s, table length: 3,050 mm, table height: 950 mm, throat depth: 400 mm, ram plate length: 3,050 mm, distance table to ram: 400 mm, clearance between the columns: 2,600 mm, oil tank capacity: 350 l, Equipment: CE marking, safety light barrier, Hydraulic press brake LVD PPEC-5 170/30 Touch Year of manufacture: 2008 Serial number: 34638 Technical specifications Force: 1700kN Working length: 3050mm Distance between uprights: 2600mm Stroke: 200mm Distance table – ram: 400mm Gap: 400mm Table width: 150mm Approach speed: 100mm/s Working speed: 10mm/s Return speed: 100mm/s Weight: 11000 kg Motor: 15kW COMMAND CONTROL CNC TOUCH LITE CNC 5 axes Y1 Y2 X R V • Table V-axis PP8170 • Reach of X-axis: 600mm • CE marking “PP3580” • Top tool clamping Eurostyle, 15 pcs • Back gauge X-R duo PP8098 • 2 front supports • 2 fingers on back gauge Fodpfx Aezl Uchjhmjpk

Condition: used, Year of construction: 2000, pressing force: 260 t, stroke length: 250 mm, table width: 840 mm, table length: 1,500 mm, air pressure: 9.807 bar, compressed air connection: 9.807 bar, ram adjustment: 120 mm, We are offering this used Chin Fong OCP-260N eccentric press with double column, year of construction 2000. Model: OCP-260N Factory number: A00373 Fpjdpfeykbcmex Ahmok Year of construction: 2000-11 Capacity: 260 tons Stroke frequency: 20–40 strokes/min Stroke: 250 mm Maximum die height: 500 mm Upper bolster clearance: 7 mm Slide adjustment (range): 120 mm Upper platen surface (L × W): 1130 × 700 mm Lower platen surface (L × W): 1500 × 840 mm Main motor power: 22 kW Poles: 4 Machine weight: 31.8 tons Compressed air pressure: 9.807 bar Oil temperature max.: +100 °C Oil temperature min.: -10 °C Oil volume: 180 liters If you have any questions or need more information, please feel free to send us a message or call us.

Condition: new, The briquette press is designed for compressing all types of sawdust and wood shavings into briquettes. The briquetting press features a compact, user-friendly design and is manufactured in Germany. The large oil tank enables continuous operation. The briquette press is ready for immediate use – simply plug it in and start working. Fpodpfx Ajyr Tpnohmek

Condition: new, machine/vehicle number: ZBP 30, The AMIS briquetting press type ZBP 30 produces 30 mm briquettes. These briquettes are ideal for combustion in wood gasifiers and smaller wood chip boilers or heating systems. Any material from a woodworking operation (shavings, dust, etc.) can be briquetted. Fpjdpjyr I Hnefx Ahmjk Wood chips, sawdust, wood shavings, etc., are generated in all craft and industrial woodworking companies. These materials incur significant storage and transport costs on a daily basis. Briquetting presses offer an ideal solution by compressing the material into briquettes, which are simple and space-saving to store and transport. Furthermore, the risk of spontaneous combustion is significantly reduced. The briquetting presses require little space, feature sturdy construction, and are equipped with low-maintenance technology. Whether it is wood, paper, biomass, foam, or polystyrene, the ZBP can briquette all suitable materials. With a throughput of up to 35 – 130 kg/h, they are especially suited for small and medium-sized enterprises.

Condition: new, machine/vehicle number: AMIS Brikettierpressen Typ ZBP 50, 60 und 70, AT A GLANCE: Variable container dimensions (customizable to customer requirements) Left- or right-hand configuration Hydraulics with separate oil tank Fpodpfsyr I Huox Ahmjk All model series also available as “DUO” variants Wood chips, sawdust, wood shavings, etc. are generated in all woodworking and industrial processing businesses. Every day, storage and transport costs for these materials are significant. Briquetting presses offer the ideal solution, as briquettes are easy and space-saving to store and transport. Additionally, the risk of spontaneous combustion is significantly reduced. Briquetting presses require little space, are robustly constructed, and equipped with low-maintenance technology. Whether wood, paper, biomass, foam, or polystyrene – the ZBP series briquettes any suitable material. With a throughput capacity of up to 35 – 130 kg/h, they are particularly suitable for small and medium-sized enterprises. Flexible installation options thanks to the availability of left- and right-hand designs. So start briquetting today!

Condition: new, For industrial production of rectangular briquettes The ZBP 500 compacts pressable materials into high-density briquettes. The briquettes are easy to store and, thanks to their stackability, can be transported efficiently. In the press chamber of the hydraulic press unit, the briquettes are shaped by a pressure cylinder. This allows up to nine briquettes per minute to be produced with a pressing force of 1 kg/cm². Standard equipment:  Safety limit switches for oil temperature and oil level  Oil cooler  Automatic briquette length monitoring  Automatic hopper fill level monitoring  Control cabinet with PLC control for fully automatic operation Options: Fpedpjyr I Hzjfx Ahmok  Custom hopper extension available to meet customer requirements  Press stamp with inscription / logo

Condition: excellent (used), Year of construction: 1989, Veneer press Manufacturer: Bürkle Type: U60 Year of manufacture: 1989 Plate dimensions: 2,200 x 1,250 mm Opening width: 400 mm Pressing pressure: 60 tons Specific pressing pressure: 2.2 kg/cm² Heating: Electric Motor power: 0.75 kW Emergency stop device: Emergency stop cable Weight: 3,000 kg Dimensions: 2,750 x 1,380 x 1,785 mm Fodpsztnhmsfx Ahmopk

Condition: refurbished (used), Year of construction: 1998, overall weight: 33,000 kg, working width: 4,300 mm, HACO hydraulic press brake, Pressmaster 43230 model 4.3 m x 230 tons Retrofit with new Easybend 2DT touch-screen CNC control X-axis back gauge with ball screw Manual crowning table 2 adjustable front supports Fsdpfx Aozqabaehmepk Machine designed for standard European tooling

Condition: reconditioned (used), Year of construction: 2004, functionality: fully functional, working width: 2,500 mm, bending force (max.): 75 t, Refurbished machine Haco press brake, PPM type, 2.5m x 75T Control with + and - buttons Motorized back gauge, X-axis European standard type punches Fodexanm Ajpfx Ahmjpk One-piece die

Condition: used, The SANDT Type 410 is for DIE-Cutting of difficult materials, particularly in the leather goods and printing industries, leather goods, cardboards and plastic. Schwenkarmstanze / hydraulic Clicking Press SANDT Typ 410 Fjdjzt Acfjpfx Ahmspk Serial-No. 760044 Stanzkraft / Pressure 22000kgs Stanzfläche / Die Cutting area max. 650 x 650mm Tischfläche / Cuttig Surface max. 550 x 900mm Hub 0 - 60mm Abmessungen / machine dimension 900 x 870 x 1400mm Gewicht / weight 840kg Online-Video-Inspection by WhatsApp - MS Zoom - Telegram On Stock Emskirchen/Nürnberg - Available Immediately - Can be test

Condition: used, functionality: fully functional, With this offer, you are purchasing a used “Rotex Air Lite V3 IVM” textile press Item for sale: Fpsdpfx Ahszpw E Hjmsk 1x Rotex Air Lite V3 IVM Condition: This offer is for a used device, which may show signs of wear (minor scratches or discoloration). The unit has been tested to ensure it is in working order. Packaging and Shipping: You are welcome to inspect the unit during our business hours. Please schedule an appointment to do so! Sturdy packaging and worldwide shipping are available upon request! Before shipping or pickup, we will record a video of a functional test for you. For more information, please feel free to contact us directly.

Condition: used, Letter Press Tiegel in good condition - DIE Cutter Heidelberg OHT in einem guten Zustand. Buchdrucktiegel - Stanztiegel / Letter Press Tiegel - DIE Cutter Heidelberg OHT Year 1953 - Serial-No. 43717 Size min.: 40 x 70mm - max. 260 x 380mm Speed min.: 2.200 sph - max. 5.500 sph Standard chase: 260 x 340mm Skeleton chase: 260 x 350mm Komplett mit Zubehör und Schließrahmen / Complete with tools and accessories include frame Online-Video-Inspection by WhatsApp - MS Zoom - Telegram On Stock Emskirchen/Nürnberg - Available Immediately - Can be test Fjdoztzp Rspfx Ahmspk

Condition: good (used), Year of construction: 2006, functionality: fully functional, Press force: 50 t Bending length: 1275 mm Frame width: 1040 mm Stroke: 215 mm Usable installation height: 385 mm Overhang: 420 mm Standard equipment: - Robust machine frame as a welded construction in all-steel design - Press beam with high bending strength - Electro-hydraulic upper drive via proportional valves - Modern block hydraulics Fpsdpfx Ajzt R Hrehmek - CNC back gauge with rack and pinion drive for the X and R axes - Safe shifting of the gauge fingers from the front - Upper tool clamping system "New Standard Clamping II" manual - Lower tool holder for EV dies, clamping hydraulic, shifting programmable (2 positions) - Control system TRUMPF TASC 6000 - Safety device consisting of side and rear protective doors - Control cabinet air conditioning - Network compatible Optional equipment: - 2 additional gauge fingers, attachable - Upper tool clamping hydraulic - Bendguard - Roll protection cover at the rear - Support console - Preparation for ACB

Condition: good (used), Year of construction: 2007, functionality: fully functional, Press force: 170 t Bending length: 3050 mm Distance between uprights: 2550 mm Stroke: 445 mm Fsdpfx Ahjzt R Euomspk Accessories: - 2 front support arms - Light curtain in front of the machine - Foot switch - Wila quick-release system at the top and bottom - TASC 6000 control system - Die shifting mechanism - Including tools - Crowning - 6-axis back gauge

Condition: used, Year of construction: 2005, Pressure 800 t distance between columns 2560 mm stroke 1050 mm Distance table/ram, stroke up 1870 mm Table surface area 2500 x 1730 mm pressure of drawing cushion in table 300 t Die cushion stroke in table 395 mm Die cushion area in table 2300 x 1300 mm Ram surface 2500 x 1730 mm Die cushion pressure in ram 63 t Die cushion stroke in ram 150 mm Side window 1000 mm Oil volume 4300 l Power capacity 200,0 kW Dimensions (WxDxH) 4,1 x 2,8 x 10,0 m Height above floor 7,0 m year of manufacture 1974 overhaul 2005: formerly type BZE 800, converted to ZE 800 by manufacturer with new ram and new cylinder mit ölhydraulischem Antrieb, hydraulischem gesteuertem Ziehkissen im Tisch und Stößel Fsdszrpt Ispfx Ahmopk stored in dismantled condition - Video at seller’s site before dismantling available

Condition: used, Year of construction: 2005, Pressure 600 t distance between columns 2600 mm stroke 900 mm Distance table/ram, max. stroke up, adjustment up 1600 mm Table surface area 2500 x 1730 mm pressure of drawing cushion in table 250 t Fpodszrptzepfx Ahmek Die cushion stroke in table 400 mm Die cushion area in table 2300 x 1300 mm Die cushion pressure in ram 63 t Die cushion stroke in ram 160 mm Die cushion area in ram 1900 x 1300 mm Ram surface 2500 x 1730 mm Side window 1100 mm Oil volume 3500 l Power capacity 200,0 kW Dimensions (WxDxH) 4,1 x 2,8 x 9,6 m Height above floor 6,4 m year of manufacture 1974 - overhaul 2005: complete new electrical cabinet with control Siemens S7 and safety control Pilz with oil-hydraulic drive, hydraulic controlled drawing cushion in table and ram, hydraulic cutting impact cushioning stored in dismantled condition - Video at seller’s site before dismantling available