Used Screw In Temperature Sensor for sale (28,250)

Condition: good (used), WSM Stationary Screwing Unit Assembly and testing of components for car radios and navigation systems. The assembly station is enclosed in a protective housing. The service doors are equipped with monitoring switches with interlocks. The doors are locked during automatic operation and can only be opened during automatic stop or manually after pressing the "Doors" button on the control panel. Automatic operation cannot be started with a door open. Operational Sequence The station is loaded with the pre-assembled component via the transfer belt. The following describes the operation steps of the automatic station with a transfer belt. In normal operation, all three stations operate in parallel. - Positioning the test unit (WT) with the pre-assembled module in station 2.1 - Lowering the carrier with the scanner and vision sensor - Scanning the 3 codes (front panel, front PCB, SD PCB), comparison with the database - Checking the correct locking of the FFC in the connector Dsdpfx Aajibichj Hskt - Raising the carrier and lowering the test unit onto the conveyor belt - Positioning the test unit (WT) with the pre-assembled module in station 2.2 - Positioning the screwdriver and screwing the front PCB in place - Lowering the test unit (WT) onto the conveyor belt - Positioning the test unit (WT) with the pre-assembled module in station 2.3 - Lowering the light shield and making contacts, adjusting the carrier with the test sensors from below - Type-dependent testing of the SD + CD slot lighting and buttons - Functional test of the CD eject button - Lowering the test unit (WT) onto the conveyor belt > continue If errors occur during testing, they are displayed on the screen. and can be repaired if possible. For this, the system is switched to manual operation and the doors are opened. After the repair and restarting the automatic system, the workpiece carrier is tested again in the station. If a repair is not possible (e.g., due to a screw error), the workpiece carrier is marked as NIO (Not Okay) in the control system and is not processed further. Manual NIO marking and rejection is also possible. Financing through our bank is also available. komplett-konzept.leasingo.de More assembly stations, new and used, can be found in our shop! International shipping costs on request!

Condition: like new (used), Year of construction: 2025, operating hours: 30 h, functionality: fully functional, measuring range X-axis: 800 mm, measuring range Y-axis: 800 mm, measuring range Z-axis: 500 mm, workpiece weight (max.): 100 kg, warranty duration: 12 months, type of input current: AC, input voltage: 230 V, compressed air connection: 6 bar, Equipment: documentation/manual, type plate available, High-Precision Reference Measuring Center – Mahr OMS 800/500 HA Multisensor Coordinate Measuring Center with Extended Z-Axis Measuring Range Factory overhauled and modernized in 2025 – ready for immediate use. Technical Data Measuring range: 800 × 800 × 500 mm Sensors: - Optical sensor: Camera & laser (active measurement) - Renishaw TP200 touch probe (other options: TP20, SP25, etc.) - Camera system with 10x objective (optional: 1x, 5x, 20x) - 3D multisensor head MSH with transmitted light, incident light, laser & probe mount Software: OptiCheck3D 2025 – user-friendly, interactive programming Evaluation station: High-performance PC with Windows 11 Professional (64bit) Accuracy: - Length measurement uncertainty: E1 = 0.9 + L/600 µm - E3 = 1.9 + L/400 µm (L in mm) - Scale resolution: 0.1 µm Dimensions / Weight: - Size: 2360 × 1940 × 3300 mm - Weight: approx. 8090 kg Dkjdpfx Aaoxbyxys Het - Max. workpiece weight: 50 kg (glass), 100 kg (granite), extendable - Traverse speed: max. 200 mm/s Device Details Model: Mahr MarVision OMS 800/500 HA CNC Design: High-precision, air-bearing multisensor measuring center Special feature: Active vibration damping (BILZ Bi Air) Condition: From laboratory use in precision measurement room, factory-refurbished in 2024 New price of comparable equipment: from approx. €650,000 Delivery time: approx. 4 weeks from order Highlights - Leasing option: 0% interest, without bank transaction - Factory overhaul 01/2024 with warranty & guarantee - Live demo: Available online or on-site - Optional service package: Worldwide transport, commissioning, calibration/certification, training, user instruction - 18 months free: Software update service & hotline support - Software: Full license OptiCheck3D (no subscription fees) - Remote service: Online board support directly at the measuring device - Custom modifications & retrofits on request - Latest 64-bit CNC controller & evaluation station (Windows 10/11) Supply & Environment - Compressed air: 6 bar ±0.1 bar (filtered, ISO 8573-1, consumption approx. 160 Nl/min) - Voltage: 115/230 V ±10%, 50/60 Hz ±5%, 2500 VA Environment: - Temperature: 20 °C ±1 K - Humidity: 40–70% RH - Vibrations: < 5 µm amplitude at < 5 Hz Service & Demo - Online demos available at short notice - Optional on-site demonstration at customer location

Condition: new, Year of construction: 2020, functionality: fully functional, Equipment: documentation/manual, Manufacturer: BRINOX Product: LEP13.1 – AS-Batch Temperature Control Unit System type: Temperature control unit for ammonium sulfate batch system Year of manufacture: 2020 Serial number: 1003620 Tag number: MR-ASF-ASF61-KK6770 Equipment number: 20022748 Media Connections / Process Data WCOV – Chilled water supply: 6 °C WCOR – Chilled water return: 12 °C WSV – Process/municipal water AIP10 – Control compressed air 6 bar Design as a closed temperature control module with integrated pump and heat exchanger technology. Dimensions Overall dimensions as per layout: approx. 1920 x 1435 x 1573 mm (L x W x H) Compact, skid-mounted unit with welded stainless steel frame. Construction Frame construction in stainless steel Fully insulated piping (industrial insulation) Stainless steel shell-and-tube heat exchanger Electrical inline water heater WT1011 Pump PU1021 Pump PU9203 Heat exchanger WT1001 Expansion vessel BH9701 Fittings: GEMÜ shut-off valves Pneumatically actuated valves Manual ball valves Pressure gauges Sensors and instrumentation as per P&ID Complete piping and component labeling provided. Dedpfeyl Izxox Aa Hokt Condition New and in original packaging. Not yet put into operation in production. Factory new condition. Supplied directly by the manufacturer Brinox. FAT / Test Status FAT carried out. Leak test: Test medium: Compressed air Test pressure: approx. 3 bar Holding time: 1 hour Result: Passed Calibration: Pressure gauge calibrated Measuring range: 0–10 bar Calibration certificate available Traceable to national standards Documentation Turn-Over-Package complete Included documents: FAT plan FAT report Non-conformance form Layout drawing check Maintenance and calibration accessibility check P&ID review Leak test report Calibration certificates Documentation check Factory certificate 2.1 according to EN 10204 LBM material list incl. EU declarations List of installed components – equipment List of installed components – instrumentation points (PLT) Material parts list for as-built isometry Key Features GMP-compliant construction Pharma/biotech project quality Full traceability Compact plug-and-play skid design Completely piped, insulated, and ready to connect Immediately available

Condition: new, Year of construction: 2020, functionality: fully functional, Equipment: documentation/manual, Manufacturer: BRINOX Type: LEP2.3 – Wash Solution Temperature Control Unit Year of Manufacture: 2020 Serial Number: 1003507 LEP2.3 KK6761 Package 8 Tag No.: MR-INH-VPR61-KK6761 Equipment No.: 20023781 Technical Data System Type: Temperature control unit / heating and cooling module for wash solution (CIP or process washing system) Design: Compact, fully pre-assembled skid unit in robust stainless steel frame construction, crane-liftable via integrated lifting points. Frame and Construction: Welded stainless steel construction in industrial design, free-standing, multi-level piping configuration for optimal space utilization. Maintenance-friendly access from multiple sides. Integrated cable trays. Piping: Stainless steel process piping in hygienic design, welded and partially flanged. Multilayer thermal insulation of main lines and apparatus. Integrated drain and vent fittings. Valve Technology: Multiple manual ball valves (GEMÜ) in main and bypass circuits. Pneumatically actuated control and shut-off valves for automatic temperature regulation. Diaphragm and control valves integrated in the heating and cooling circuit. Instrumentation and Control: Temperature measurement points in both supply and return lines. Pressure sensors in the process section. Integrated flow measurement. Electrical junction box with protective labeling. Automatic temperature control via pneumatic control valve. Heat Exchanger: Cylindrical stainless steel heat exchanger, insulated and integrated into the piping system. Designed for controlled heating and/or cooling of the wash solution in a closed loop. Pump Technology: Two electrically driven centrifugal pumps with red-painted motors for process recirculation within the temperature control unit. Electrical: Electrical junction box with warning markings. Wired sensors and actuators. Prepared for integration into a central PLC or process control system. Application Dsdpfx Aaeyl It Ij Hokt This system is used for precise temperature regulation of a wash solution within a pharmaceutical or biotechnological process system. Typical areas of application include CIP systems, production plant washing stations, and temperature-controlled cleaning processes in the pharmaceutical and biotechnology sectors. The wash solution circulates in a closed loop via pumps, is temperature controlled by the integrated heat exchanger, and continuously monitored by sensors. Temperature is regulated automatically via pneumatic control valves to maintain defined setpoints accurately. Construction Compact modular skid design with fully insulated main lines. Stainless steel surfaces in hygienic industrial finish. Clearly organized media routing and structured piping layout. Crane-transportable via integrated lifting points. Condition Year of manufacture 2020. Very good visual and technical condition. Professional execution in pharmaceutical plant engineering. FAT / Documentation Typically supplied with CE conformity, Factory Acceptance Test (FAT), and technical documentation including P&ID diagrams and material certificates for product-contacting components. Special Features Fully insulated temperature control module in a compact, high power density design. High-quality valve technology (GEMÜ). Multiple integrated measurement and control points. Suitable for validated pharmaceutical processes. Industrial, pre-assembled skid solution with clearly structured media routing.

Year of construction: 2025, condition: new, functionality: fully functional, Cost-effective single-column, microprocessor-controlled tensile testing machine for tensile, compression and bending tests up to 3kN Comfortable Windows software for universal test procedures, simple tests can also be performed without a PC. Made in Germany Basic equipment: • Machine with sensor (optionally between 50N and 3kN) • Accuracy class 0.5 • Windows based software • Warranty 2 years Optionally available: • Extensive gripping tools (mechanical, pneumatic and hydraulic), for example: Dodpfxjd H S Hie Aa Hjkt pressure platens Screw and wedge grips bending grips Special designs according to customer specifications • extensometer • Temperature and climatic chamber • Windows software PM-Soft-Smart for universal use, freely programmable • putting into operation and training

Operating hours: 54,000 h, condition: ready for operation (used), functionality: fully functional, CINCINNATI PROTON 60-30G Screw diameter: 60 mm, L/D = 30 Djdpfoyrihgjx Aa Hjkt Grooved feed section Throughput: approx. 450 kg/h PE Motor (DC drive): 163 kW Screw speed: max. 221 rpm Tool zones: 5 pcs + 1 pc for adapter Melt pressure & temperature sensors included Control system: Cincinnati EXc Pro-NT Cylinder in bimetal design – condition: good Screw with wear-protection and hardened feed section – condition: good Dimensions (L x W x H): 2,580 x 1,430 x 1,800 mm Weight: 2,500 kg

Condition: used, functionality: fully functional, “functionally tested; item comes from the dismantling of equipment from an automotive supplier” Manufacturer: SICK Type: AT20E-PM111 (AX20 series) Category: Array sensor / Edge detector Function: Edge detection, measurement of diameters/widths, reflector-capable Sensing distance / Measuring range: 25 mm / Measuring range 20 mm Output: PNP / Analog (4–20 mA) depending on the variant Dedpfx Aaszh Anke Hokt Protection class: IP67 Temperature range: −10 … +55 °C Dimensions: compact design (see datasheet) Weight: approx. 0.14 kg

Condition: used, The Braibanti/Pavan extruder is designed for the continuous production of short-cut pasta, breakfast cereals, and pet food. The prepared dough is conveyed through a temperature- and moisture-controlled screw extruder toward the die, which ultimately defines the shape of the product. Extrusion takes place under controlled pressure and temperature to ensure consistency and structural integrity. At the end of the extruder, a motorized, speed-controlled rotating knife cuts the extruded product to the desired length. Prior to extrusion, the dough undergoes a structured preparation process. It begins with a two-step mixing system that combines dry and wet ingredients into a homogeneous mass. This system uses a single mixing arm with directionally adjustable paddles to ensure proper pre-conditioning and hydration. The final stage of preparation takes place in a high-performance mixer/kneader unit, which further develops the dough structure to achieve optimal plasticity, consistency, and elasticity-critical parameters for stable and high-quality extrusion performance. Continuous mixer - preconditioner PR220 (2-line version) ± 100 L / screw Single mixing shaft with adjustable paddles, dual execution Motor 2 x 18,5 Kw - 978 rpm Liquid and dry ingredient supply Inspection and cleaning hatch Dkodpfozzavfsx Aa Het Mixer VM210 ± 150L Single mixing shaft execution with adjustable paddles Motor 1.5 KW - 1461/64 rpm Extruder BR220 Dual execution, 2 extrusion heads Motor 2 x 37Kw - 1482 rpm Gearbox Sumitomo Cyclo Double-walled extruder housing, suitable for cooling Production capacity (Pet food) calculated at 30-40 kg/min (depending on the product) Operating pressure ± 30-40 bar depending on the die Powered cutting head/chopping knife (motor 1.1 Kw -920 rpm) Dimensions (L x W x H): 5.000 x 2.200 x 2.400 mm Possibility to run 2 separate products, 2 extrusion lines on 1 frame. without electric cabinet and controls

Condition: ready for operation (used), Year of construction: 1998, operating hours: 28,973 h, functionality: fully functional, overall weight: 2,750 kg, total length: 2,800 mm, total width: 1,150 mm, total height: 1,770 mm, power: 132 kW (179.47 HP), volume flow: 1,630 m³/h, type of cooling: water, input voltage: 400 V, input frequency: 50 Hz, operating temperature: 201 °C, pressure: 2.75 bar, rotational speed (max.): 12,874 rpm, type of input current: three-phase, Equipment: compressor, documentation/manual, type plate available, 3 Aerzen VM 30 screw compressors Used to pneumatically unload railway cars. Manufacturer: Aerzen Type: VM 30 Volume flow: 27.17 m³/min (1630.2 m³/h) Pressure increase: 2.75 bar Compressor speed: 12,874 rpm Shaft power: 105 kW Motor power: 132 kW Final temperature: 201 °C The compressed air is cooled with water via a shell and tube heat exchanger. Year of manufacture: 1998 Dimensions: Length: 2800 mm Width: 1150 mm Height: 1770 mm Djdpfx Aerkpp Hea Hskt Weight: approximately 2750 kg Operating hours: Compressor 1: 28,109 hours Compressor 2: 28,222 hours Compressor 4: 28,973 hours Regular maintenance was carried out by a qualified service company!! Not operated since 2019. Have been stored in a dry and heated location since then.

Year of construction: 2015, condition: excellent (used), The temperature control unit is for sale ;2015- the new price was 4995€ Medium : Water Functions - Function for self-optimizing temperature control - Function and fault displays - User-dependent and password-protected rights - Limit comparator (tolerance band monitoring of the actual value with alarm message) - Adjustable setpoint limit - Weekly timer Dkedpfxom Dtm As Aa Hot - Automatic heating and cooling program - Freely selectable ramp function for temperature changes during heating and cooling - VNC server via Ethernet (enables complete operation and management from the PC) - 2nd temperature setpoint - Tool management (setpoints and control parameters can be be saved as a recipe) - Measured value recording for quality assurance (actual values can be be output to SD card with time stamp) - Electronic level monitoring with dry run protection - Automatic filling and replenishment with leakage and level function monitoring level function monitoring - Automatic venting Monitoring/safety - Short-circuit-proof controller and control outputs - Temperature sensor in circulating medium flow and return - Safety temperature limiter to prevent overheating and Safety valves against overpressure - Contactless heating control with solid state relay - Safety temperature reduction when switching off - Acoustic and visual warning signal with symbol and text text on the touch screen- Symmetrical mains load with three-phase drive and three-phase heating elements three-phase current heating rods - 3-fold safety shutdown of the heater - Reversible circuit breakers and motor protection switch - Dirt trap in the cooling water supply Hydraulics - Continuous cooling via motor valve

Year of construction: 2011, condition: excellent (used), CTS Type: T-30/950 Ex/I CTS Temperature Test Chamber, Explosion-Proof Control – 32-bit controller LCD control panel Digital display for set and actual values Numerical input of set values Error messages in plain text RS 232 interface Free switching channels for product-side test specimen activation Djdozd Rzwepfx Aa Hskt Temperature Testing: Temperature range: -30°C to +80°C Temperature deviation: ±0.3 K over time Temperature change rate: Heating: 2 K/min Cooling: 1.5 K/min down to -10°C Thermal radiation: approx. 1000 W at +20°C approx. 200 W at -25°C Nitrogen inerting with residual oxygen monitoring With nitrogen inerting, the test chamber is first purged with a large flow rate of N2 until the o2 content drops below 3%. Then, it switches to a base flow amount (approx. 10% of the large flow rate). The nitrogen flow for the base amount is measured and displayed using a flowmeter and monitored via a limit switch. O2 monitoring continuously extracts gas from the test chamber via a flame arrestor and passes it over an O2 sensor which checks the residual oxygen content of the extracted air. Afterwards, the gas is returned to the test chamber via a second flame arrestor. The extraction pump is monitored by a volumetric flow meter. Additional details can be found in the Dräger user manual in the appendix. The gas system is currently deactivated! All technical data refer to an ambient temperature of +25°C, nominal voltage 400V, without test specimen, without irradiation, and without additional equipment. Dimensions: Test chamber volume: 950 liters Test chamber dimensions: Height approx. 700 mm / Width approx. 900 mm / Depth approx. 1500 mm External dimensions: Height approx. 2400 mm / Width approx. 1270 mm / Depth approx. 3125 mm Operating data: Electrical connection: 400V +6/-10 %, 3/N, 50 Hz Nominal power: 21.6 kW Rated current: 36.5 A Protection class: IP 54 Condensate drain: non-pressurized, R 1/2" inner thread Sound pressure level:

Condition: as good as new (ex-display), Year of construction: 2022, Kaeser screw compressor SM 13 - 11 bar exhibition piece at a special price Volume flow at 11.0 bar (g) 1.07 m³/min Electrical power consumption of the entire system at 11.0 bar (g) 9.63 kW Djdpsvk R A Sefx Aa Hjkt Specific power 9.00 kW/(m³/min) Maximum overpressure 11.0 bar Drive motor efficiency at full load 91.7% Drive motor efficiency class IE4 Nominal drive motor power 7.5 kW Drive motor speed 2955 rpm Drive motor protection class IP 55 Electrical supply 400 V / 3 Ph / 50 Hz Compressed air outlet temperature above ambient temperature (at +20°C, 30% relative humidity) 8 K Sound pressure level 65 dB(A Compressed air connection G 3/4 Location: From stock 54634 Bitburg - available immediately -

Condition: excellent (used), Here we offer a TIRA temperature testing chamber. TIRA temperature testing chamber, air-cooled. The chamber has the option for an external test box, including an external sensor connection, and can therefore also be used as an external temperature control unit. Temperature range: -20°C to +140°C Temperature stability over time: ±0.1°C to ±0.3°C External dimensions: Width 860 mm x Depth 1500 mm x Height 2100 mm Test chamber dimensions: Width 601 mm x Depth 545 mm x Height 692 mm Electrical connection: 400V +6% / -10% 50Hz 3P+N+PE Rated current: 10.0 (max. 17) A Rated power: 5.2 (max. 9.0) kW Dkedpfxszd Umqs Aa Hjt Net weight: 735 kg Refrigerant: R404A / R23 Type: TTRE 2001S For your safety as a buyer, please note the following information: The following steps are carried out on our offered chambers in advance: 1. Functional check and replacement of any necessary components 2. If necessary, refilling with legally compliant refrigerant 3. Leak test with certificate 4. After successful inspection, the chambers are subjected to a documented test run. Condition: used Scope of delivery: (See picture) (Changes and errors in the technical data and specifications are subject to change!) We would be happy to answer any further questions you may have by phone.

Condition: new, Year of construction: 2026, functionality: fully functional, *All of our products are made with care and covered for 1 year warranty! *Installation and Operator Training FREE • Model: FABO HY-600 • Type: Double Helix Screw Washer • Capacity: 60 ton per hour • Dimension: 1400 x 6650x1800 mm • Screw Size: Ø 600x6000 mm • Speed: 22 rev/min • Motor: 2 x 5.5 kW Heavy duty Gamak • Water Consumption: 55-205 m3 • Including chassis, motor and safety guards. Dkodpfey H Aizox Aa Hot FOR FURTHER INFORMATION PLEASE FEEL FREE TO CALL US!!!

Condition: used, Bega Screw Compressor 15kW 10 bar, Refrigerant Dryer, Compressed Air System, Compressor Station, Air Supply System, Used Machine Compressor Manufacturer: Bega Type: MSK SD15/10 /U3 Year of manufacture: 2017 Weight: 500 kg Overall dimensions: 1300 x 950 x 1150 mm Flow rate: 2.1 m³/min (2100 l/min) Maximum pressure: 10 bar Motor power: 15 kW Maximum speed: 2940 rpm Country of origin: Germany Dryer Manufacturer: BEGA Kompresszor Kft. (Friulair S.r.l.) Type: ACT23/AC Year of manufacture: May 2017 Overall dimensions: 500 x 420 x 950 mm Nominal capacity (Flow rate): 2300 l/min Maximum operating pressure: 14 bar Voltage / Frequency: 230 V / 50 Hz Power output / Rated current: 0.46 kW / 2.8 A Refrigerant type / mass: R134a / 0.35 kg Country of origin: Italy Air Receiver Tank Manufacturer: Huch GmbH Behälterbau (Neuruppin, Germany) Type / Serial No. (Herstell-Nr.): 103455 Year of manufacture: 2002 Overall dimensions: 2000 x 615 mm Nominal capacity: 500 Liters Max. allowable operating pressure: 11 bar Max. allowable operating temperature: -10 to +50 °C Standard / Certification: EN 286 Teil 1, CE 02-0035 Country of origin: Germany Dsdpfszbqn Tex Aa Hskt

Condition: used, Year of construction: 2024, functionality: fully functional, Year of manufacture: 2024 Cutting ranges: Cutting range 90° round 360 mm Cutting range 90° flat (W x H) 360 x 360 mm Clamping range 0 - 360 mm Smallest section length 10 mm Smallest dimension to be cut 10 x 10 mm Shortest remaining piece length in automatic operation (only possible with geometrically flawless surfaces) 35 mm Shortest remaining piece length in single cut 10 mm Dimensions and weights: Overall dimensions (L x W) 1,650 x 2,900 mm Dkedozv Th Djpfx Aa Hjt Height 2,030 mm Material support height 700 mm Weight 3,450 kg Performance characteristics: Saw motor, frequency-controlled 4 kW Total connected load 6 kW Single material feed length 500 mm Multiple feed length 9,999 mm Machine roller track, length 1,100 mm Ball-bearing mounted, robust transport rollers 8 pieces Roller diameter 60 mm Roller axle spacing 135 mm Cutting speed, continuously variable 12 - 150 m/min Saw blade dimensions 6,096 x 34 x 1.1 mm Alternatively 6,096 x 41 x 1.3 mm Cutting feed: electrically adjustable via ball screw Material feed: ball screw Material clamping: hydraulic Saw blade cleaning: self-adjusting chip removal brush, electrically driven Coolant: Pump capacity 75 l/min at 2 m head, Coolant tank volume approx. 100 l Paint finish: Light grey RAL 7035, anthracite grey RAL 7016 textured paint Compressed air connection: approx. 6 bar required (customer-side) KASTO sawing machine control ProControl 9" Hardware  Industrial PC, fanless, no moving parts  Robust metal housing, aluminum front panel  Resistive touchscreen  Color TFT display 9"  Ambient temperature 0 - 50 °C  Protection class, front: IP65 Software  Operating system Windows 10 Enterprise LTSC 2019  SIMATIC S7 - 1500 Failsafe Software Controller CPU

Year of construction: 2010, operating hours: 29,000 h, condition: excellent (used), Category: Twin-screw extruder Number: DE27699 Manufacturer: Coperion - Werner & Pfleiderer Type: ZSK 50 MCC+ Year: 2010 Screw diameter: 2 x Ø 50.0 mm L/D: 48:1 Motor: 129 kW Details: Co-rotating, segmented screws and barrel, vacuum pump, temperature control unit, 2x side feeders, 1x side degassing The extruder is in very good condition and has only 29,000 operating hours. Options: 7-fold dosing system from Motan Colortronic, dryer (Motan LA 1200/4), IPS strand extraction, strand conveyor belt, water bath, granulator, vibrating screen. All options are available immediately at extra charge. This offer does not meet your requirements? Please visit our website Plama or send us your detailed enquiry. We offer suitable equipment for almost every budget. Dkedpfxjxykcge Aa Hjt

Condition: excellent (used), functionality: fully functional, Brabender Single Screw Extruder 30 mm – 30 L/D – with K-Tron Twin Screw Feeder – Strand Die For sale is a fully functional Brabender single screw extruder in a compact design, ideal for laboratory, development, or small-scale production applications. Technical Data: • Manufacturer: Brabender • Screw diameter: 30 mm Dedsyi Am Rjpfx Aa Hokt • Process length: 25 L/D • Drive: 5.5 kW • Multi-zone heating system (5 zones) • Compact control cabinet with digital temperature control • Strand die adapted Features: • K-Tron twin screw feeder • Compact, clearly arranged control unit • Multiple heating zones with individual control • Melt temperature & melt pressure monitoring Condition: • Fully functional • Well-maintained overall condition • Ready for immediate use A trial run with customer material is available upon prior arrangement.

Condition: good (used), Code: 0386 Brand: BOTTARINI AIR KRONE - ITALY Model: KS 22 - CE Standard Silenced screw air-compressor with tank and dryer for craft and industry - CE Standard Features: Palletised design, this means that it can be placed anywhere using a simple transpallet. No bolting down is required. Panel-enclosed design that allows for easy access from all sides for routine maintenance Clearly visible and functional control panel features a pressure gauge, air pressure, running time counter, a digital temperature regulator, and a timer. Light on/off button and fault indicator lights Technical data: Motor power 20 Hp 10 Bar 2 m³/min Air delivery 70 CFM Djdpfx Ajy Spkioa Hjkt Vertical tank 500 liters Dryer Overall dimensions Compressor mm 700 x 700 x 1000 h - 210 kg Overall dimensions Dryer mm 500 x 500 x 600 h - Kg 50

Condition: excellent (used), functionality: fully functional, Twin-Screw Extruder / Twin-Screw Kneader COLLIN ZK 25 For sale is a COLLIN ZK 25 twin-screw extruder in a compact laboratory or technical center design. The machine is ideal for trials, compounding, product development, as well as smaller-scale production applications. The extruder features a screw diameter of 2 x 25 mm with a process length of 36 D (6x6 D). Depending on the configuration, screw speeds of 460 / 600 / 800 min⁻¹ are possible. The drive power is 9.7 / 12.5 / 16 kW. The maximum melt pressure is 320 bar, and the maximum melt temperature is 400 °C. The machine is equipped with multiple heating zones. Barrel heating is 1 x 850 W plus 5 x 1200 W, and nozzle/adapter heating is 600 W. Water cooling is available, and temperature control is provided for zones 1 to 6, with water cooling connected via hose. Technical Data: • Manufacturer: COLLIN • Model: ZK 25 • Design: Twin-screw extruder / Twin-screw kneader • Screw diameter: 2 x 25 mm • Screw length: 36 D • Screw speed: 460 / 600 / 800 min⁻¹ • Max. melt pressure: 320 bar • Max. melt temperature: 400 °C • Weight: approx. 550 kg Dedpfxoy A H Umo Aa Hjkt • Dimensions: • Length: approx. 2,100 mm • Width: approx. 600 mm • Height: approx. 1,900 mm • Screw center height: approx. 1,100 mm Electrical Data: • Connection: 3 x 400/230 V, 50/60 Hz • Power supply: L1 / L2 / L3 / N / PE • Fusing: 3 x 50 A • Max. connected load with downstream units: 30 kW Applications: Ideal for laboratory usage, technical centers, R&D, test series, compounding, and material testing.

Condition: new, Year of construction: 2015, operating hours: 3,000 h, Operating hours: 3000. Water tank: 800 liters. Equipped with: 160 cm dispensing unit, lateral displacement 60 cm to the right, prepared for GPS integration. Optional: rear-view camera, 120 cm dispensing unit, 500 or 1,150-liter water tank, surface water pump (incl. hose and basket), high-capacity side nozzles, bracket for standpipe for hydrants, mounted on equipment carrier, e.g. Holder, Wille, Multihog, hand lance with 15 m water hose on the drum. Features: capacity per day: 17,000-35,000 m²/day*, operating speed at 100% weed coverage (min.): 0.5 km/h, average treatment speed: 3-5 km/h, operating speed at low weed coverage: min. 5 km/h, water consumption during weed control (min.): 34 l/min, drive via the hydraulic system of the carrier vehicle (min. 60 l/min at 180 bar), 2 x high-tech burners 110 kW with min. 92% efficiency according to EN 303-2, burner emission class: > EURO 6, automatic water softening system with 5 l canister and level monitoring, control unit with touchscreen for controlling and monitoring the system in the carrier vehicle, data storage for 5 days and daily performance readout via USB stick (Excel format), preparation for GPS integration, water pressure during weed control: 0.2 bar, water temperature at the plant during weed control: 98-99.6°C, active temperature control (software-controlled - no bypass control) for a constant water temperature of 99.6°C (+/- 0.6°C), burner drive: diesel or Aspen D biodiesel, capacity of the burner tank: 105 l, capacity of the water tank: 800 l, standpipe bracket, reversing camera, sensor-based dispensing unit with infrared sensors, application system: 2 rows with 20 valves in 4 independent sections, dispensing unit: working width 160 cm, lateral working nozzles (2 left, 2 right), plus 2 high-performance nozzles left and right, with 60 cm lateral displacement to the right, stainless steel hose reel with 15 meter hose and 20 cm hand lance, adapter and frame with support feet for mounting the unit on the carrier vehicle, water tank (plastic) 800 liters with C-pipe connection and level indicator, dry-run protection, water filter, standard color: RAL 9006, weight of the heating unit (net): 560 kg (without water and fuel), machine dimensions: (L x W x H) 3,500 x 1,750 x 1,600 mm, weight of the dispensing unit: 340 kg, storage location: null. Dsdpfxju Hf A Ae Aa Hokt

Condition: new, Year of construction: 2020, operating hours: 10 h, functionality: fully functional, machine/vehicle number: 52AMG162, compressed air connection: 6 bar, working width: 560 mm, warranty duration: 12 months, operating speed: 400 mm/s, Komfi Laminator Amiga 52I (Intelligent In-Line Feeding) New, Manufactured 2020 Specifications: Max. speed of lamination: 25 m/min Max. output: 8000 sheets/h Min. sheet dimensions: 200 × 250 mm Max. sheet dimensions: 560 × 800 mm (or up to 1016 mm) Paper weight: 115-600 g/m² Paper thickness: Max 0.7 mm (with overlap > 0) / Max 1.4 mm (with overlap < 0) Max. paper pile: 6 cm (depending on sheet length) Thickness of laminating film: 24-50 μm; OPP, PET, Nylon Sheet overlap accuracy: ± 1 mm Feeder: Intelligent In-Line Feeding (connection with the PRinter) Laminating Unit: Adjustable distance stoppers for lamination unit to enable processing thick substrates and windows lamination. ”On-the-fly” side-adjustable unwinding shaft with adjustable brake force. Height-adjustable and removable spread roller perfectly removes wrinkles from laminate. IR heating for laminating cylinder. Temperature sensor inside the cylinder for precise regulation. Rubber coated pressure roller. Dodpfxjzb Db He Aa Hekt The powerful pneumatic pressure system guarantees even nip pressure and perfect lamination results. Separator & Delivery: Decurling unit consisting of bar and roller with position control to move the snapping moment automatically when the position of decurler is changed. Built-in film perforator to enable sheet separation. Cam-driven separation roller with adjustable tearing action, delivery roller and sheet skewing wheel. Fixed delivery desk with adjustable air nozzles.

Condition: new, Year of construction: 2022, Kaeser screw compressor SK 22 - 11 bar - exhibition piece - Volume flow at 11.0 bar (g) 1.67 m³/min Electrical power consumption of the entire system at 11.0 bar (g) 13.7 kW Max. overpressure 11.00 bar Drive motor efficiency at full load 91.2% Drive motor efficiency class IE3 Drive motor rated power 11.0 kW Drive motor speed 2960 rpm Drive motor protection class IP 55 Electrical supply 400V / 3 / 50Hz Compressed air outlet temp. above ambient temperature (at +20°C, 30% relative humidity) 6 K Dkedpfsvk R Dcox Aa Hst Sound pressure level 66 dB(A) Max. usable warm air volume 2500 m³/h Compressed air connection G 1 Cooling oil capacity 7.0 l Cooling oil type compressor SIGMA FLUID MOL Dimensions (W x D x H) 750 mm x 895 mm x 1260 mm Weight 312 kg Location: from stock 54634 Bitburg - available immediately -

Condition: used, Year of construction: 2011, Used Equipment Year of Manufacture: 2011 Condition: Currently installed Equipment and Technical Data: -Filter housing base ring NFHSU 9/9 with discharge chute for press - Discharge: 1.1 kW - Storage volume in the base ring approx.: 3.25 m³ - Dimensions L x W x H (incl. base ring) 2440 x 2440 x 900 mm - Ground clearance: 350 mm - Conveyor screw for briquetting press 0.75 kW - Extension and expansion rings are optional; max. storage volume approx. 12 m³ - Extension and injection ring NFHSU for 9/9 and 10/10 Jet, L x W x H: 2480 x 2480 x 500 mm - Expansion ring for NFHSU 9/9, 2480x2480x700 mm, with inspection door and type-tested explosion flap - Filter for filter housing NFHSU 9/9/20, filter area 116 m²: The Nestro filter system NFHSU is a solid filter construction made of 4 mm galvanized steel sheet and is designed for outdoor installation and weather resistance. This filter system is particularly robust and designed for underpressure operation up to -3,500 Pa. The filter system is equipped with upper and lower inspection doors 600 x 600 mm, with automatic filter regeneration, dry extinguishing system, differential pressure switch / volumetric flow monitoring and the necessary explosion protection. Note: Filter is equipped with high-quality filter material, BIA category M, antistatic, residual dust content < 0.1 mg/m³ and suitable for return air operation. Further technical data: - Filter tube length: 2,000 mm - Filter tube diameter: 230 mm - Number of filter tubes: 81 Dkedjzvz Tbspfx Aa Hot - Filter area: 116.0 m² - Filter regeneration: automatic/motorized - Number of vibrating motors: 4 pcs - Fan shroud for NFHSU 9/9 including inspection door - Fan US-FHN (clean gas) 22 kW 16,400 m³/h - 3,200 Pa: A Nestro high-performance fan with above-average efficiency and high energy saving potential when using a frequency inverter (optional). The robust welded construction is primed and painted in RAL 5015. The fan is delivered as standard with an inlet cone and backflow damper. Technical data at a glance: - Volumetric flow: 16,400 m³/h - Corresponding underpressure: 3,200 Pa - Electric motor: 22 kW / 400 Volt / 50 Hz - Speed: 3,000 rpm - Design: B5 - Pressure nozzle: without - Application area: Nestro underpressure filter and others - Injection nozzle d= 400 mm with flange ring - Injection nozzle d= 350 mm with flange ring - Backflow damper d= 350 mm with flange edge - Backflow damper d= 400 mm with flange edge - Briquetting press C150; 30 - 50 kg/h, hydraulic unit 5.5: Technical data: - Power consumption (hydraulics): 5.5 kW - Briquette diameter: 50 mm - Weight: 650 kg - Briquetting performance with a bulk density of approx. 250 kg/m³, material-dependent: 30 - 50 kg/h - Ground clearance with base frame (art. no. 710300): 350 mm - Briquetting press, dust-proof - Briquetting press complete with hydraulic solenoid valve control for automatic operation, oil tank with 100 l oil, in welded construction, including main cylinder, stuffing cylinder, gripper cylinder, pressing jaw, electrical control panel with fully automatic control and 5 m cable The press is standardly equipped with: Monitoring switch for oil temperature, hardened press bushing, connection part for briquette line and automatic briquette length adjustment

Condition: good (used), Year of construction: 2015, Atlas Copco Oil Free Screw Compressor with built-in Air Dryer Model SF2+FF 7.75 bar / 112 PSI Year 2015 400 volts three phase, 2.2 KW / 3 HP, 2885 RPM 8.9 CFM / 4.21 lts/s Dedpjy Iplfsfx Aa Hskt Very little use Ex Pharma Facility