Used Sawmill Alignment for sale (1,550)

Condition: used, functionality: fully functional, - Polish production - DTR (Technical Documentation / Operation Manual) - Maximum length of processed material: 2800 mm Njdpfx Aboq Rc Rloysdc TECHNICAL PARAMETERS: - Minimum length of cut prism: 600 mm - Maximum thickness of cut prism: 110 mm - Maximum width of input material: 450 mm - Maximum width of finished board: 150 mm - Minimum width of finished board: 70 mm - Saw blade diameter: 400 mm - Output capacity up to: 20 m³ - Power of right vertical spindle motor: 3.5 kW - Power of left vertical spindle motor: 3.5 kW - Rotational speed of vertical saw drive motors: 2850 rpm - Power of horizontal saw motor: 22 kW - Rotational speed of horizontal saw drive motor: 2850 rpm - Rotational speed of feed drive motor: 1450 rpm - Feed speed (stepless adjustment): 0 - 20 m/min - Supply voltage (50 Hz): 3×400 V - Machine dimensions (L/W/H): 7250 / 1700 / 1600 mm - Transport dimensions (L/W/H): 4700 / 2400 / 1600 mm - Machine weight: 1300 kg

Condition: excellent (used), Band saw system Band saw stand - Brenta, 1500mm roll diameter Band saw carriage - Artiglio Eagle 1100 Ndodpfx Aefhl Snsbyec 3 supports Complete with full automation.

Condition: new, Technical Data • Application: for frame assembly • Minimum frame outer dimension (mm): 120 x 120 • Maximum frame outer dimension (mm): 700 x 2200 • Machine length (mm): 2750 • Machine width (mm): 1250 • Machine height (mm): 900 • Machine available in special sizes Nsdpfx Abefiqlleyedc Machine Features • Precise alignment of frame strips eliminates any displacement of the mitered surfaces relative to each other. • Manual alignment of frame strips is no longer required. • Frames can be produced economically through automation. • Frame dimensions are not limited by the machine design. • Various popular methods for joining frame miters are possible. • The compact design results in a small footprint for the machine. • Simultaneous gluing of the center layer is possible. • Complete fronts can be glued in a single process.

Year of construction: 2020, condition: new, Häwa root reduction unit, NEW Type H 276 / 800 Trunk diameter 0.2m – 1m (root collar 1.2m) Njdpefccp Hefx Abyjdc Trunk length min. 2.4m - 5m (longer lengths also possible) Total weight 5t Total power consumption 45kW with wireless remote control

Condition: good (used), Primultini band saw Roller diameter: 1300 mm Roller width: 140 mm Nsdpfx Absd Sclhsysdc with Planomatic system

Condition: like new (used), Year of construction: 2025, operating hours: 4 h, functionality: fully functional, machine/vehicle number: Digitest II, DIGI TEST II Modular hardness testing system for fully automatic hardness tests according to Shore, VLRH, and IRHD on composite materials, soft-elastic materials, elastomers, plastics, and foams with variable testing geometries. Standards • ASTM D2240 • ASTM D1415 • DIN EN ISO 868 • DIN ISO 48-2 • DIN ISO 48-3 • DIN ISO 48-4 • NFT 46-003 • TD 00002001 • TD 00002002 Nedozn I N Hepfx Abyodc • Measurement method • Shore A • Shore A0 • Shore D • Shore 0 • Shore 00 • Shore 000 • Shore 000S • Shore E • Shore B • Shore C • Shore D0 • Micro Shore A • Micro Shore D • Shore AM • Shore M • IRHD L • IRHD N • IRHD M • IRHD H • VLRH Application areas Flat, inclined, convex, and concave geometries of composite materials, soft-elastic materials, elastomers, plastics, and foams. The digi test II enables precise and user-independent hardness measurements on elastomers, polymers, soft-elastic materials, composite materials, and foams. The modularly expandable measuring system is used in research and development as well as in production and quality control to determine the material hardness of a wide range of products and to ensure quality standards. Modularly expandable Interchangeable measuring devices allow for easy switching between the numerous measurement methods in the areas of Shore, IRHD, and VLRH without tools and with just a few steps. Thanks to the wide range of positioning and measuring devices offered, the digi test II is the right choice for laboratories, production, quality assurance, and development when testing a wide range of products. Many shapes – one solution Thanks to its modular expandability, the digi test II enables the measurement of all sample geometries. Whether you want to perform measurements on flat, inclined, concave, or convex geometries, you will obtain exact measurement values from a sample thickness of 0.7 mm thanks to the approach system. ROTOFIX FOR DIGI-TEST II Positioning device available as an accessory for the automatic measurement of a different number of samples and measurement positions. Secure measurement values without user influence In addition to perfect alignment as a table unit, the Digi-Test II ensures the optimal measurement position of the test samples through its numerous positioning devices. The most accurate measurements without user influence and manual pre-setting are guaranteed, which saves you time for the important things. Comprehensive analysis through various measurement methods Do not only measure the hardness of your test piece, but also the flow curve of the material during the test. With the option for hysteresis measurements, the Digi-Test II provides additional insights into the characteristic properties of the material. CENTROFIX Manually operated positioning device available as an accessory for measuring individual test specimens for the digi test II and the Gelomat. Modular attachments for the Centrofix can be used to clamp and fix samples and molded parts of any kind for measurement.

Condition: used, Year of construction: 2021, operating hours: 50 h, functionality: fully functional, machine/vehicle number: Digitest II, DIGI TEST II Modular hardness testing system for fully automatic hardness tests according to Shore, VLRH and IRHD on composite materials, soft-elastic materials, elastomers, plastics and foams with variable testing geometries. Standards • ASTM D2240 • ASTM D1415 • DIN EN ISO 868 • DIN ISO 48-2 • DIN ISO 48-3 • DIN ISO 48-4 • NFT 46-003 • TD 00002001 • TD 00002002 • Measurement method • Shore A • Shore A0 • Shore D • Shore 0 • Shore 00 • Shore 000 • Shore 000S • Shore E • Shore B • Shore C • Shore D0 • Micro Shore A • Micro Shore D • Shore AM • Shore M • IRHD L • IRHD N • IRHD M • IRHD H • VLRH Application areas Flat, inclined, convex and concave geometries of composite materials, soft-elastic materials, elastomers, plastics and foams. The digi test II enables precise and user-independent hardness measurements on elastomers, polymers, soft-elastic materials, composite materials and foams. The modularly expandable measuring system is used in research and development as well as in production and quality control to determine the material hardness of a broad product portfolio and to ensure quality standards. Modularly expandable Interchangeable measuring devices enable a simple change between the numerous measurement methods in the areas of Shore, IRHD and VLRH without tools and with only a few steps. Thanks to the wide range of positioning and measuring devices offered, the digi test II is the right choice for laboratory, production, quality assurance and development when testing a broad product portfolio. Many shapes – one solution Thanks to its modular expandability, the digi test II enables the measurement of all sample geometries. Whether you want to perform measurements on flat, inclined, concave or convex geometries, you will receive exact measurement values from a sample thickness of 0.7 mm thanks to the approach system. ROTOFIX FOR DIGI-TEST II Positioning device available as an accessory for the automatic measurement of a different number of samples and measuring positions. Secure measurement results without user influence In addition to perfect alignment as a table unit, the Digi-Test II ensures the optimal measuring position of the test samples thanks to its numerous positioning devices. The most accurate measurements without user influence and manual pre-setting are guaranteed, which gives you time for the important things. Comprehensive analysis through various measurement methods Do not only measure the hardness of your test specimen, but also the flow curve of the material during the test. With the option for hysteresis measurements, the Digi-Test II provides additional insights into the characteristic properties of the material. Ndodpjzn Na Tofx Abysc CENTROFIX Manually operated positioning device available as an accessory for the measurement of individual test specimens for the digi test II and the Gelomat. Modular attachments on the Centrofix allow samples and molded parts of any type to be clamped and fixed for measurement.

Condition: used, Tenoning spindle 2 Stk. Number of milling agregates 5 St. Spindle diameter 50 mm Control Weinig, PC-Nexus Weinig Unicontrol 10 NC Window System — Optional: Extensive Tooling Set ----- Optionally available (at an additional cost): IV 68 Wood, Wood/Aluminum IV 78 Wood, Wood/Aluminum IV 68 Entrance Doors Manufacturer's Technical Description: ----- Item 1: Weinig Unicontrol 10 NC Window System ----- Cross-cut Saw ----- with laser alignment light; motor power: 3 kW; spindle diameter: 40 mm; spindle speed: electronically variable (with brake) from 3,000 to 6,000 rpm. Max. tool cutting circle: 400 mm Axial adjustment: 150 mm via NC axis Radial adjustment: pneumatic, to 8 positions for top edge rounding Horizontal bottom rounding unit ----- Axial adjustment travel: mechanically coupled with cut-off saw 1st Tenoning and Slotting Spindle ----- Motor power (with brake): 15 kW Spindle diameter: 50 mm Spindle speed: 2,925 rpm Max. tool cutting circle: 400 mm Tool clamping length: 640 mm Axial adjustment travel: NC axis Home position (below table): 5–10 mm Radial adjustment travel: fixed 2nd Tenoning and Slotting Spindle ----- Motor power (with brake): 11 kW Spindle diameter: 50 mm Spindle speed: 2,925 rpm Max. tool cutting circle: 400 mm Tool clamping length: 320 mm Axial adjustment travel: NC axis Radial adjustment travel: NC axis Home position (below table): 5–10 mm 1st Profiling Spindle (Climb and Conventional Milling) ----- Motor power (with brake): 11 kW Spindle diameter: 50 mm Spindle speed: 6,000 rpm Tool cutting circle: 140 mm Max. tool diameter: 232 mm Tool clamping length: 400 mm (with outboard bearing) Axial adjustment travel: 350 mm (NC axis) Radial adjustment travel: NC axis Home position (below table): 5–10 mm 2nd Profiling Spindle Nodpfx Ajzawizjbyedc ----- Motor power: 11 kW Spindle diameter: 50 mm Spindle speed: 6,000 rpm Tool cutting circle: 140 mm Max. tool diameter: 232 mm Tool clamping length: 400 mm (with outboard bearing) Axial adjustment travel: 350 mm (NC axis) Radial adjustment travel: NC axis Home position (below table): 5–10 mm Horizontal Profiling Unit (Top) ----- Motor power (with brake): 3.0 kW Spindle diameter: 40 mm Clamping length: 40 mm Spindle speed: 5,850 rpm Max. tool cutting circle: 130 mm Pneumatic adjustment: 8 positions (axial and radial) 3rd Profiling Spindle ----- Motor power: 11 kW Spindle diameter: 50 mm Spindle speed: 6,000 rpm Tool cutting circle: 140 mm Max. tool diameter: 232 mm Tool clamping length: 400 mm (with outboard bearing) Axial adjustment travel: 350 mm (NC axis) Radial adjustment travel: NC axis Home position (below table): 5–10 mm Vertical Profiling Unit (Right, at Machine End) ----- Motor power (with brake): 3.0 kW Spindle diameter: 40 mm Clamping length: 160 ...

Condition: good (used), Horizon BQ-270C Perfect Binder Machine in very good condition. Ready to use. Very low mileage. Manufacturer’s description: Nodpfjz Iczhjx Abyjdc Professional binder for perfect paperback binding. This fully automatic binder features an exceptionally sturdy design and is equipped with a hot glue gun, making it effective even for small and very small quantities of book covers or pages. The Horizon BQ-270C is a single-jaw binder with automatic cover feeding, which, operated by a single person, delivers impeccably bound books of consistently high quality. Equipped with a core thickness scanner, it allows for on-demand binding. Binds books with a thickness of 0.5 to 50 mm and a spine length of 135 to 320 mm, with a maximum production rate of up to 500 books per hour. Factory-installed cutter with additional scoring knives. Maximum milling depth up to 3 mm. Automatic cover feeding via a suction drum with a secure, consistent alignment with the bound sheets. A factory-installed system creates 4-fold creases on the cover, which automatically adjusts for precise alignment.

Condition: excellent (used), Year of construction: 2010, operating hours: 5,285 h, functionality: fully functional, input voltage: 230 V, type of input current: AC, laser power: 105 W, type of cooling: air, total width: 1,240 mm, total height: 1,140 mm, total length: 1,920 mm, overall weight: 580 kg, travel distance X-axis: 1,245 mm, travel distance Y-axis: 710 mm, travel distance Z-axis: 610 mm, input current: 20 A, laser wavelength: 10,600 nm, input frequency: 50 Hz, Speedy 500 in good condition, coming from a model-making workshop. Few operating hours (5285 hours). Laser source replaced in late 2018 (Synrad firestar ti100; nominal 100 W, 151 W as a new part; 2392 hours of operating time). Power supply also replaced in 2018 (Meanwell RSP-2400). Last service: 08/2026 Extensive accessories included: Laser pointer for precise alignment of the workpiece 5.0" lens 2.0" lens Pass-through – for processing longer sheets Gas kit Cutting table Vacuum table Honeycomb table / aluminum honeycomb core for vacuum table Rotary engraving attachment – for bottles, glasses, etc. Njdsz Eh Eajpfx Abyedc iCut software and camera (currently disassembled) Includes Mistral ECO 220V / 50HZ extraction system (motor relatively new). Original new price: €86,708.58

Condition: like new (used), operating hours: 12 h, KILIA 65 Liter Meister Plus – factory-reconditioned by HELTEK | KILIA For sale is a KILIA 65-liter high-speed cutter / Meister Plus, which undergoes complete factory reconditioning at HELTEK | KILIA. This is not a simple repair or cosmetic refurbishment. The machine is completely disassembled and rebuilt from the ground up, both technically and visually. The goal is to achieve a condition that consistently aligns with the current machine standards of HELTEK | KILIA. The 65-liter cutter is ideal for butcher shops, meat processing plants, and industrial food processing operations. Technical data: Manufacturer: KILIA Model: Meister Plus / High-speed cutter Bowl capacity: 65 liters Batch processing capacity: approx. 46 kg per batch Main motor: 22 kW Knife shaft speed: approx. 50–5,100 rpm Reverse / mixing speed: approx. 50–500 rpm Plate speed: approx. 7–20 rpm Knife and plate drive: continuously variable, frequency-controlled Voltage: 400 V / 50 Hz Total electrical connection power: approx. 28 kW Customer-side fuse: 50 A Control: modern PLC Operation: 7-inch HMI touch panel Central lubrication: yes Scope of the HELTEK | KILIA factory reconditioning The machine is completely disassembled, except for the base frame. As part of the reconditioning, the following work is carried out, among other things: new base plate, professionally welded in machine frame completely refurbished and blasted stainless steel areas refurbished or glass bead blasted base frame with high-quality new powder coating 22 kW main motor new or completely overhauled and certified by Siemens new motor tensioning device made of stainless steel plate shaft drive new or completely overhauled and certified by the manufacturer plate shaft bearing completely new new bearings and new bearing seats for the plate shaft bearing new knife shaft new knife shaft bearing new electronic central lubrication system new wear parts new scrapers, guides and sliding elements made of food-grade blue POM electrical system and control completely new The electrical equipment is also comprehensively modernized: new PLC control new 7-inch HMI touch panel new frequency inverters new contactors and relays new cables and wires Ndodpfez A Ufzsx Abyec new or revised sensors modern safety technology complete rewiring This gives the machine modern control and drive technology with good spare parts availability and high serviceability. Factory-reconditioned instead of just used You will receive the extremely robust basic structure of a proven KILIA cutter, combined with modern control, drive and safety technology. Proven KILIA quality. Modern HELTEK technology. Ready for many more years of production. After completion of the factory reconditioning, the machine is completely inspected and subjected to a FAT – Factory Acceptance Test. Warranty We provide a 6-month warranty on the factory-reconditioned machine in accordance with our terms and conditions. The knife shaft bearing is excluded from the warranty. Inspection and machine acceptance / FAT can be arranged at HELTEK | KILIA. Transportation, installation and commissioning can be offered on request.

Year of construction: 1974, condition: used, functionality: unexamined, For sale: Ndsdpfx Abez Dn Uljysc - Circular saw mill, type OS65, from a carpentry/lumber mill in very good condition. - Low operating hours, only approx. 800-1000 m³/year. - Clamping carriage, self-propelled. - Auxiliary carriage. - Approx. 15m of guide rails for the clamping carriage/auxiliary carriage. - Splitting wedge/outfeed rollers, not driven. - €20,000 net / plus VAT. The following are also available separately: - Log infeed system - Chain hoist with transverse conveyor Prior inspection is required.

Condition: new, Year of construction: 2026, functionality: fully functional, machine/vehicle number: HS-14E, overall weight: 185 kg, total width: 135 mm, total length: 144 mm, total height: 228 mm, fuel: electricity, SCHORR Log Splitter 14t HS-14E PRO Ndodpfx Aezwmypjbyec Where conventional electric splitters with 12 tons reach their limit, the HS-14E goes further: 14 tons of splitting force drive the splitting wedge through hardwood, dry and knotted logs, evenly and without jamming. The powerful hydraulic cylinder with a 9.5 cm diameter reliably delivers the pressure, stroke by stroke. Splitting is done vertically with a splitting length of up to 104 cm: meter-long logs fit with room to spare, as do shorter sections from 56 cm. This allows you to quickly work your way through the pile of logs, piece by piece. The most strenuous part of the splitting process is not the splitting itself, but lifting the logs. The HS-14E is equipped with an integrated log lifter specifically for this purpose: hook the log, lever it, and the section aligns itself effortlessly into the splitting position, without straining your back and shoulders. When not in use, the log lifter serves as a stable protective bar on the machine. Operation is performed via the two-hand safety control, and the massive, robust design with a weight of 185 kg ensures a secure stand, even at full splitting force. The HS-14E does not require a tractor or a power take-off: the 400 V electric motor with 3.5 kW is connected to the standard 16 A socket and delivers its power quietly and without emissions. This allows you to split wood in the barn, in the hall, or on the farm, where gasoline engines would be disruptive and a tractor is not available. The technology is deliberately kept simple, robust, and repairable: hydraulics, steel frame, electric motor – no unnecessary frills. The HS-14E is delivered pre-assembled and with hydraulic oil already filled: simply connect it and start splitting. Wear and replacement parts are in stock, and we handle repairs in our own workshop. You buy directly from the manufacturer and receive personal advice. And for those who want to combine a power take-off and electric power, the HS-22PE with 22 tons is the larger model. Technical data -- Manufacturer: SCHORR -- Type: HS-14PE -- Splitting force: 14 t -- Weight: 185 kg -- Drive: 400 V electric motor (3.5 kW, 16 A) Dimensions: -- Length: 1440 mm -- Width: 1350 mm -- Height: 2280 mm -- Splitting wedge: 17.5 cm -- Splitting diameter: max. 30 cm / min. 10 cm Your advantages at a glance -- Ready for immediate use – no long waiting time -- Massive design – 185 kg weight for maximum stability -- Comfortable log lifter for heavy wood -- Spare parts always available -- Competent service & advice Whether delivery or collection in 48465 Schüttorf – we offer the right solution.

Condition: used, Year of construction: 1992, functionality: fully functional, power: 330 kW (448.67 HP), control type: PLC-controlled, actuation type: hydraulic, For sale is a used Quattro Spaner bandsaw, Super 40 model, manufactured in 1992, consisting of: - Spaner - Centering unit - 4-bandsaw system Super 40 This system is particularly suitable for the efficient cutting of light to medium-strength round timber and enables precise and efficient processing in a compact design. Technical data: Max. round timber diameter: 58 cm → Debarking up to 42 cm Min. round timber diameter: 13 cm → Debarking up to 8 cm Feed rate: up to approx. 59 m/min → Reduced to approx. 20 m/min for large cross-sections Daily output: approx. 250–300 cubic meters/day → Depending on round timber diameter and cutting Condition and previous use: The system was in operation at a sawmill with an annual production of approximately 50,000 cubic meters in a single-shift operation until summer 2025. It was regularly maintained until it was taken out of service and was fully functional. However, due to its age and for reliable long-term operation, a complete overhaul is necessary. An inspection of the system for sale is possible by arrangement. An identical Quattro system, which has already been completely overhauled, can be inspected on-site during ongoing production. This allows interested parties to gain a clear picture of the system's performance and potential applications after an overhaul (see photo). Price on request. We will gladly send further technical information as well as photos and videos upon request. Inspection is possible after prior appointment. Nedezvx Shopfx Abysdc

Condition: used, CNC Wire EDM Machine AccuteX AU-1000iA | Year 2007 | Large-Scale For sale: a professional, reliable, large-scale wire EDM machine from the renowned Taiwanese manufacturer AccuteX, model AU-1000iA. This machine is ideal for machining large and heavy parts, producing injection molds, dies, and tools with the highest precision. TECHNICAL SPECIFICATIONS: - Manufacturer: AccuteX - Model: AU-1000iA - Year of manufacture: 2007 - CNC control: Proprietary AccuteX (Windows CE) - Working travels (X × Y × Z): 1100 × 650 × 400 mm - Travels in cone axes (U × V): 150 × 150 mm - Cone cutting angle: ±21° (for height H=100 mm) - Maximum workpiece weight: up to 5000 kg (fixed table design, moving column) - Supported wire diameters: 0.15 - 0.33 mm - Machining type: Submerged KEY FEATURES AND BENEFITS: - T-Base construction: Extremely stable body made of Meehanite castings, damping vibrations and resistant to thermal and mechanical loads. Ndodpfx Aozt Sinebyjc - Optical (glass) linear scale system guaranteeing repeatability and positioning accuracy at the micro scale. - Original AccuteX Wire Alignment Device for wire centering/positioning (in a dedicated box with wiring). INCLUDED WITH THE MACHINE – A RICH SET OF AUXILIARY EQUIPMENT: - Professional set of EDM clamping elements: numerous clamps, clamping jaws, positioning screws, and pins. - Precision strips and base beams for quick mounting of large parts and molds on the work table. - Additional consumable accessories and wire guiding mechanism components.

Condition: good (used), Franz Haas Wafer Stick Baking Oven, Model EWB 1/1, completely refurbished. The machine is constructed from ASIS 304 stainless steel (with the main frame made of carbon steel). The oven is equipped with a rotating ring, which has adjustable speed control to achieve the desired baking characteristics for the wafer sticks. The ring has been cleaned and checked (re-aligned), and the supports/bearings are brand new. Fans have been replaced with new units. The exhaust outlet and flange have been replaced for quick installation. The machine comes with two extruders with bushings for ribbon forming and tube diameter shaping. Equipped with a cutting knife featuring a pneumatic actuator and photoelectric sensor for precise cutting (tube length adjustment is possible). The oven includes a stainless steel batter tank mounted on a frame with a trolley. Fitted with pumps that feed batter from the tank onto the ring surface. Comes with a new control panel and a new gas pressure regulator. Speeds of the ring and pumps are adjustable via frequency inverters. Dimensions: length 3200 mm, width 1400 mm, height 1700 mm. The machine is powered by natural gas, high-methane type, symbol E (previously GZ 50). Electrical requirements: 3x400V / 16A, consumption approx. 2.5/3 kWh. The machine has undergone a complete overhaul. All thermal elements have been replaced with new, environmentally-friendly components—resulting in lower gas consumption and enhanced efficiency. Ndsdpfx Abeywgaxeyoc Output: approx. 120-150 kg per 8 hours.

Condition: new, Year of construction: 2026, functionality: fully functional, Baljer & Zembrod Diameter Reduction Units Nodpez R Iy Nefx Abyjdc • Used to reduce the diameter of logs over their entire length to a specified diameter (e.g., 60 cm). • Cutter lengths: 420 mm to 1500 mm • Log lengths up to 7 meters • Log centering on the log’s center for maximum yield • Clamping device for the end faces of the log, with a rotary table; clamping frame is hydraulically adjustable.

Condition: excellent (used), functionality: fully functional, Year of construction: 2016, operating hours: 5,244 h, load capacity: 5,000 kg, lifting height: 4,550 mm, free lift: 2,250 mm, load center: 600 mm, fuel type: gas, mast type: duplex, construction height: 3,150 mm, motor manufacturer: GM, gearing type: hydrostat, fork carriage width: 1,150 mm, fork length: 1,200 mm, fork width: 120 mm, fork thickness: 50 mm, tire condition: 100 %, front tire type: cushion tires (black), front tire size: 23 X 10 - 12, rear tire type: cushion tires (black), rear tire size: 355 X 65 - 15, overall weight: 12,200 kg, empty load weight: 7,200 kg, total height: 2,600 mm, total length: 2,420 mm, total width: 2,250 mm, color: yellow, Equipment: 3rd hydraulic function, 4th hydraulic function, CE marking, all wheel drive, cabin, front guard, head guard, lighting, pallet forks, sideshift, 🚜 COMBILIFT C5000XL | LPG | DUPLEX 4550 MM | FORK SIDESHIFT | FULL HEATED CAB | READY TO WORK ✅ FULLY SERVICED | WARRANTY | WORLDWIDE DELIVERY Looking for a reliable forklift that delivers value from day one without unexpected maintenance costs? We offer a fully inspected, serviced, and tested COMBILIFT C5000XL four-way forklift, ready for immediate use in manufacturing, warehousing, and logistics. Ideal for long, heavy loads and confined spaces. ⭐ KEY ADVANTAGES ✔ Full service and operational testing ✔ Start-up warranty ✔ Super Elastic tires in 100% condition ✔ Powerful 65 HP LPG engine ✔ DUPLEX 4550 mm mast ✔ Hydraulic fork sideshift ✔ Full heated cab ✔ Four-way multidirectional steering ✔ Excellent technical and cosmetic condition ✔ Ready to work without additional investment ✔ Live online demonstration available ⚙️ TECHNICAL SPECIFICATIONS Manufacturer: COMBILIFT Ndsdpfx Aboz Su E Uoysc Model: C5000XL Year: 2016 (02/2016) Type: Four-way multidirectional forklift Capacity: 5000 kg Load centre: 600 mm Engine: LPG, G.M., 3.0 L, 65 HP Operating hours: 5244 h Mast: DUPLEX Lift height: 4550 mm Free lift: 2850 mm Fork sideshift: Hydraulic Cab: Full heated cab Service weight: 7200 kg 📏 DIMENSIONS Cab roof height: 2600 mm Collapsed mast height: 3150 mm Overall length: 2450 mm Overall width: 2250 mm Platform length: 1200 mm 🔧 FORKS Length: 1200 mm Width: 120 mm Thickness: 50 mm Hydraulic sideshift included 🛞 TIRES – 100% CONDITION Front: 23 x 10 - 12 Super Elastic Rear: 355 / 65 - 15 Super Elastic 🛠️ EQUIPMENT ✔ Hydraulic fork sideshift ✔ DUPLEX lifting mast ✔ Four-way steering ✔ 65 HP LPG engine ✔ Full heated operator cab ✔ Opening windows ✔ Working lights and LED lighting ✔ Warning beacon ✔ Air conditioning and cab heating ✔ Windshield wipers and ventilation fan ✔ Adjustable operator seat ✔ Third and fourth hydraulic valves ✔ CE certification and operator's manual 🏭 IDEAL FOR Timber processing, sawmills, steel mills, steel service centres, structural steel manufacturing, pipes, profiles, long materials, warehouses, logistics centres, and manufacturing plants. Suitable for outdoor operations and indoor use with adequate ventilation. Excellent maneuverability in confined spaces. 🏆 WHY FT LOGISTICS? We specialize in forklifts, sideloaders, four-way and multidirectional forklifts, and warehouse equipment. Every machine undergoes full inspection, servicing, and testing before delivery. 🚜 OVER 200 MACHINES AVAILABLE FROM STOCK! 🌍 Supplying customers throughout Europe and worldwide. Hundreds of European customers trust us and return for further purchases. 🤝 OUR SERVICES ✅ Full pre-delivery service and warranty ✅ Technical advice and after-sales support ✅ Leasing and financing ✅ European and worldwide transport ✅ Export assistance and customs documents 📸 Live demonstrations, photos, and videos available. Individual delivery quotations directly to your facility. 📞 FT LOGISTICS Sp. z o.o. FT LOGISTICS – WE DELIVER MACHINES THAT ARE READY TO WORK!

Condition: excellent (used), For sale: complete fire-fighting trailer equipped with a professional ALCO MONITOR water cannon. The set is fully mobile – ideal for fire brigade use, fire protection, and securing large areas (fuel depots, sawmills, production plants, storage yards). Technical condition: • ALCO / MONITOR water cannon – heavy-duty cast iron construction Ndodjz Slkvjpfx Abyec • Full adjustment of direction and spray angle (control wheels) • Directional nozzle on extended boom • KALI Anhänger Service GmbH trailer, GVW 700 kg • Hitch: Peka Fahrzeugbau, type DV127 • Two side tanks with filling ports • Shut-off valves, fire-fighting quick couplings • Stabilizing supports with height adjustment • Lighting installation, fenders, wheels in very good condition • Well-maintained, complete, ready to use Applications: • Voluntary/Professional fire brigades • Large production facilities • Timber yards, sawmills • Chemical and fuel plants • Securing mass events • Extinguishing fires from a great distance / high water flow

Condition: used, Year of construction: 2012, operating hours: 10,000 h, machine/vehicle number: TP109, Used Capping Machine AVE 6T up to 7000 bph The used capping machine AVE 6T up to 7000 bph delivers high efficiency and versatility for the bottling industry. Specifically, it handles medium to high-speed production lines, ensuring consistent and reliable results. Furthermore, the machine for Stelvin Lux uses six capping heads to provide precise and uniform operation throughout every bottling cycle. Moreover, its design maximizes production speed, enabling the handling of up to 7000 bottles per hour. This performance, in turn, supports businesses aiming to improve operational efficiency and maintain consistent product quality. The system supports aluminum screw caps of the Stelvin Lux type, measuring 30×60 mm. Consequently, this cap type creates an airtight seal, preserving product integrity and extending shelf life. Producers in the wine and beverage industry often choose this format for its reliability. Additionally, the machine rotates clockwise, aligning with standard bottling line layouts and reducing the need for costly modifications. Its compact design, moreover, integrates smoothly into existing production environments, even when space is tight. Nodpfx Absvgvabsysdc  Safety Features and User-Friendly Maintenance The used capping machine AVE 6T up to 7000 bp enhances safety by incorporating advanced protective features. For instance, these systems shield operators from potential risks, reducing accidents and improving workplace safety. Furthermore, the safety mechanisms allow operators to access and maintain them quickly, ensuring consistent compliance with industry standards. The technical manuals of Stelvin Lux, in addition, offer clear instructions for installation, maintenance, and troubleshooting. These guides, therefore, enable operators to resolve issues efficiently, minimizing downtime and preserving productivity. Additionally, the machine’s modular design allows technicians to replace components quickly, streamlining maintenance tasks and lowering repair costs. Current State and Electrical Requirements The machine for Stelvin Lux currently remains in storage, ready for immediate installation on a new production line. Moreover, it operates at 400 V, with a power requirement of 3 kW and a frequency of 5 Hz. Therefore, users should verify these specifications to confirm compatibility with their existing electrical systems. Furthermore, the machine’s low energy consumption supports production facilities in reducing operational costs without compromising performance. Robust Performance and Durability of Stelvin Lux Thi machine withstands demanding production environments with its durable construction. Notably, its six capping heads ensure consistent quality in every operation, maintaining high production standards. Consequently, businesses rely on this machine to meet ambitious production goals while preserving the integrity of their products. Moreover, its precision and efficiency make it a valuable asset for any bottling operation. Conclusion of teh Used Capping Machine AVE 6T up to 7000 bph The used capping machine AVE 6T up to 7000 bph offers an effective and reliable solution for bottling operations. In particular, it boosts efficiency by combining precise capping heads, strong safety features, and simple maintenance requirements. Additionally, its seamless compatibility with standard production lines and energy-efficient operation provide ...

Condition: used, Year of construction: 2007, operating hours: 14,700 h, machine/vehicle number: ET194, Labeling machine for sale with optical centering 6000 bphTechnical Specifications & Performance DataThis P.E. Labellers rotary adhesive labeler with optical centering is engineered for precision bottle decoration within a used bottling line or new installations. Built for consistent, high-quality labeling across beverage production environments, it balances speed with accuracy and repeatability.Manufacturer / Model: P.E. Labellers – 8T 4S 4E adhesive SL GlueYear of manufacture: 2007Production speed: up to 6,500 bottles per hour (bph)Stations / Plates: 4 adhesive stations; 8 motorized plates with dedicated photocellsOptical centering: Advanced system for precise label alignment on decorated, embossed, or irregular bottlesLabeling applications: Body, back, neck and optional L-/U-seal for caps (via dedicated adhesive unit on trolley)Container types: PET and glass bottles; adaptable for other rigid containers (e.g., aluminum) with appropriate format partsProducts: Suitable for water, juice, beer, wine, spirits, soft drinks, and moreDimensions (WxLxH): 2000 x 2900 x 2500 mmWeight: 2100 kgElectrical requirements: 380 V, 50 Hz, 5 kWConfiguration codes (OEM): No. of plates: 8; Rotation direction: 1; Plate movement: 2; Number of stations: 4; Labeling method: 0,4; Label placement: 0,1,2,4; Optical centering system: 2; Head adjustment: 1Advanced Automation & Control SystemsAutomation is designed for reliable, repeatable labeling within industrial packaging lines. A touchscreen HMI and integrated PLC control all machine functions, offering recipe-based changeovers and real-time diagnostics. Servo-driven or motorized plates work in concert with photocells for synchronous optical centering, supporting premium presentation at full speed.Touchscreen HMI with programmable recipes (memory for multiple label formats)Integrated PLC and modern electronics; inverter-driven speed modulationElectric lift for quick height adjustment of the carousel and heads4-axis head adjustment on trolley for precise head positioningPhotocell-controlled label application synchronized with optical centeringManuals available for operation, maintenance, and programmingProduction Line Integration CapabilitiesEngineered to integrate seamlessly upstream and downstream with rinsing, filling, and capping machines, as well as inspection systems, coders/inkjets, and secondary packaging (shrink, wrap-around, or case packing). This second hand labeler is ideal for upgrading or completing a used bottling line without compromising performance.Compatible with standard conveyors, accumulation tables, and line controlsFast format changes supported by stored recipes and mechanical referencesMulti-format flexibility for different bottle heights and diameters with the right format setsInterfaces available for line start/stop and speed cascade with fillin... Nsdpfx Abjvlnvreyjdc

Condition: used, Year of construction: 2016, Used capsuling machine Robino & Galandrino for champagne bottles up to 000 bph The machine Robino & Galandrino ZENITH for champagne bottles up to 000 bph delivers high-precision capsuling for specific applications in the bottling sector of sparkling wines and champagne. Moreover, Robino & Galandrino manufactured the ZENITH Z 3-36 OTTICO model in 2016, incorporating advanced technology to achieve optimal capsuling results. Technical Specifications of the Capsuling machine Robino & Galandrino ZENITH Production speed: This capsuling machine processes up to ,000 bottles per hour (bph) with single capsule centering. Additionally, it reduces the speed to 9,000 bph in double centering mode, which aligns both the bottle and the capsule optically. Containers: This machine specifically accommodates glass bottles, thereby fulfilling the requirements of champagne and sparkling wine producers. Capsuling heads: The machine features application heads, which distribute capsules uniformly and precisely, even at high speeds. Capsule type: The system supports capsules for champagne and sparkling wines, thus ensuring a perfect fit on the bottle neck. Distinctive Features Optical centering system: The advanced optical centering system delivers millimetric precision during capsule application. Consequently, this capability is particularly critical for achieving high aesthetic and functional standards. Counterclockwise rotation: The machine rotates counterclockwise, which enables seamless integration with pre-existing production lines. Extended capsule stock: The extended stock capacity significantly increases operational autonomy and minimizes downtime for capsule loading. Optimized production: The ZENITH Z 3-36 OTTICO model maximizes productivity while maintaining consistent quality through its flexible configuration for various operating modes. Safety and Electrical Supply This machine adheres to strict safety standards, thereby creating a safe working environment for operators. Furthermore, it operates with a 400 V power supply, 50 Hz frequency, and 18 A current draw, ensuring stable performance and compatibility with standard industrial installations. Current Condition of the Capsuling machine Robino & Galandrino ZENITH Ndedpfx Aevu A Etjbyec The machine remains in storage. Its modular design, as a result, simplifies adaptation to different operational needs. Ideal Applications This Capsuling machine Robino & Galandrino ZENITH suits producers who require high production volumes and flawless capsuling quality. Moreover, its versatility allows usage in both new production lines and existing plants, ensuring compatibility and superior performance. Choosing the Used capsuling machine Robino & Galandrino for champagne bottles up to 000 bph guarantees access to a reliable, high-performance machine equipped with advanced optical centering technology. Thus, it represents an essential asset for high-demand production environments.

Condition: used, Year of construction: 2013, machine/vehicle number: TP129, Used AROL speciale kamma PKV capping machine 10000 BPHTechnical Specifications & Performance DataThis Arol rotary capping machine is designed for automated bottle closure in a used bottling line. The Speciale Kamma PKV model combines rotary operation with neck-grip transfer, providing controlled bottle handling through the capping process. It is configured with five capping heads and a maximum speed of 10000, supporting efficient industrial packaging operations where consistent closure application is required.Manufacturer: ArolModel: Speciale Kamma PKVYear of construction: 2013Capping heads: 5Maximum speed: 10000Machine configuration: RotaryBottle transfer: Neck-grip transferWorking-table height: 1200 mmAdvanced Automation & Control SystemsThe machine is equipped with a Siemens PLC for coordinated operation of the rotary capping cycle. Clockwise working direction is specified. Electrical supply is 400V, 3 Ph+N +T, with a 20 A electrical rating. This configuration is suited to integration into an industrial bottling line with compatible electrical and control infrastructure.Electrical supply: 400V 3 Ph+N +TElectrical rating: 20 APLC: SiemensRotation direction: ClockwiseProduction Line Integration CapabilitiesThe rotary capper can be positioned downstream of filling equipment and upstream of inspection, labeling, or secondary packaging machinery. Neck-grip transfer supports stable bottle movement at the closure station, while the included cap elevator provides automatic cap feeding to reduce manual handling. The machine is suitable for integration with conveying systems used in beverage production and broader industrial packaging applications.For bottle-based applications, capping machinery of this type can support PET and glass container handling when the bottle neck, cap format, and transfer interfaces are compatible with the installed configuration.Machine Condition & Maintenance HistoryThis second hand Arol capping machine is ready for use. It has been refurbished and is supplied with compatible spare parts. A 6-month warranty is included. The machine is offered as inspected and accepted, making it suitable for buyers seeking a prepared capping unit for a used bottling line or production-line upgrade.Operational Performance & VersatilityThe machine is specified for natural water, sparkling water, soft drinks, milk, oil, beer, wine, alcoholic beverages, and preserves. Its rotary design and automatic cap elevator make it relevant to beverage production and food-packaging environments requiring repeatable bottle closure operations. Final suitability depends on verification of the required cap type, cap dimensions, neck finish, bottle geometry, and line speed.Installation Requirements & Site PreparationInstallation requires a 400V 3 Ph+N +T electrical connection and a compressed-air supply at 6 bar. The working-table height is 1200 mm and should be considered when aligning infeed and dis... Ndsdpfoz E Dgtox Abyec

Condition: used, Year of construction: 2002, machine/vehicle number: CA83, Used ROBINO & GALANDRINO monostadio z 8 t capsuling machine- Year 2002Technical Specifications & Performance DataThis Single-stage Capsuling Machine Z 8 T by Robino & Galandrino is a robust solution for capsule application on glass bottles, engineered for wine and sparkling wine producers seeking reliable performance in a second hand, used bottling line environment. Built with Italian precision, it offers consistent capsuling quality and seamless integration into industrial packaging and beverage production workflows.Manufacturer: Robino & GalandrinoModel: Z 8 T (Monostadio)Year: 2002Configuration: Single-stage capsulingNo. of heads: 8Capsule types: PVC shrinkable plastic; Champagne/sparkling wineRotation direction: CounterclockwiseOptical centering: Not equippedContainers: Glass bottlesCompliance: CE markedAdvanced Automation & Control SystemsDesigned for dependable operation within professional bottling equipment setups, this capsuling machine supports stable, repeatable processes. Its single-stage architecture simplifies adjustments and minimizes changeover time. Operator functions are straightforward, ensuring efficient routine operations. Standard machine protections and CE conformity support safe use on modern production floors.Streamlined controls for routine start/stop and adjustmentsQuick changeovers aligned with single-stage designMechanical alignment without optical centering for robust, low-maintenance operationSafety guarding consistent with CE conformityProduction Line Integration CapabilitiesThe Z 8 T integrates easily as a standalone station or inline within a complete used bottling line. It accepts upstream glass bottle handling and passes consistently capped bottles downstream to labeling or inspection modules, supporting flexible industrial packaging layouts.Inline or standalone operationCompatible with standard glass wine bottle handling conveyorsSuitable for integration after corking/capping and before labelingCapsule application for both PVC shrink and sparkling wine formatsMachine Condition & Maintenance HistoryThis machine is currently in storage, making it available for rapid deployment into beverage production environments after routine commissioning. The overall configuration, CE conformity, and preserved components provide a solid foundation for reliable second hand operation.Current status: In storageCE marked unitSingle-stage, 8-head layout preservedOperational Performance & VersatilityOptimized for wine sector applications, the Z 8 T manages both PVC shrink capsules and champagne/sparkling wine formats. Its counterclockwise carousel and 8-head configuration deliver balanced throughput for small to mid-scale wineries and beverage producers.Ideal for Wine and sparkling wine productionConsistent application of PVC sh... Ndodpez E Dhwefx Abysc

Year of construction: 2001, condition: used, machine/vehicle number: AT109, Used CAMES bottle dryer - Year 2001Technical Specifications & Performance DataThis pre-owned bottle drying tunnel is engineered to remove surface moisture from containers before downstream operations. Manufactured by CAMES, model TNN 1, it provides consistent air-blown drying to stabilize labels and packaging quality across a wide range of beverage production lines. Its continuous tunnel configuration supports steady throughput and uniform drying performance suitable for high-demand industrial packaging environments.Manufacturer: CAMESModel: TNN 1Year: 2001Machine type: Drying Tunnel (air-blowing)Primary function: Bottle surface drying prior to labeling and packagingContainer compatibility: Designed for PET and Glass bottle handlingOperating principle: Directed airflow across bottle surfaces in a continuous tunnelIntegration: Inline installation on conveyors between rinsing/filling and labelingAdvanced Automation & Control SystemsThe CAMES TNN 1 supports stable and repeatable drying through controlled airflow within the tunnel section. Typical integration includes line start/stop synchronization, safety interlocks with upstream and downstream equipment, and straightforward operator controls for airflow adjustments. The tunnel concept minimizes manual intervention, helping maintain consistent bottle dryness that is critical for pressure-sensitive or glue-applied labels.Production Line Integration CapabilitiesBuilt for inline operation, this drying tunnel integrates seamlessly with conveyors and standard bottling layouts. It fits naturally between rinsing/filling and labeling stations, ensuring bottles are properly conditioned for high-quality labeling and subsequent packaging. The CAMES TNN 1 accommodates multiple bottle sizes and shapes commonly used in beverage production, supporting flexible format changes with mechanical adjustments and change parts as required by the line.Machine Condition & Maintenance HistoryThis is a second hand drying tunnel from 2001, suitable for integration into a used bottling line. Its straightforward, robust design favors routine maintenance and predictable operation in industrial environments. As with all pre-owned bottling equipment, maintenance schedules and line-specific service records can be aligned with the receiving plant’s preventive maintenance plans.Operational Performance & VersatilityThe CAMES TNN 1 improves downstream quality by ensuring reliable bottle dryness prior to label application. Consistent drying reduces label defects, enhances packaging appearance, and supports efficient line speeds. Its air-blowing tunnel architecture works across a wide range of beverage production scenarios and container materials, making it a versatile choice for industrial packaging facilities that manage diverse bottle formats and product portfolios.Installation Requirements & Site PreparationInstallation involves positioning the tunnel over an existing conveyor section with adequate straight runs upstream and downstream for smooth bottle flow. Site preparation typically includes providing the appropria... Ndedpfx Abjz E Dkfeyec