Used Romer Powder Coating for sale (119)

Year of construction: 2020, condition: new, Pneumatic connection 1 " • Controls 7 "color touch panel • Paint tank capacity 6-7 kg • Air consumption during painting 15Nm3 / h • Air consumption for cleaning 350Nm3 / h • Hopper paint level sensor Yes • Ultrasonic screener Yes • Powder injectors up to 12 pcs Hedpfx Asfz U Nujacefn Description • RP-01 pump for topping up the paint with fresh paint from cardboard • Two modes of operation, paint recovery with mixing or total waste • Sealed fluidization paint hopper • Automatic program for cleaning the tank and injectors with compressed air • Hopper powder level sensor assembly • Automatic refilling of the tray with paint from cardboard • Paint level sensor in refill box • An audible alarm alerts the operator when there is low paint in the box • The center is connected with the cabin control via ModBus protocol • Programmable powder suction valve to keep the powder center clean

Year of construction: 2020, condition: new, Pneumatic connection 1 " • Controls 7 "color touch panel • Paint tank capacity 6-7 kg • Air consumption during painting 15Nm3 / h • Air consumption for cleaning 350Nm3 / h • Hopper paint level sensor Yes • Ultrasonic screener Yes • Powder injectors up to 12 pcs Hfsdpfefz U Rcsx Aacon Description • RP-01 pump for topping up the paint with fresh paint from cardboard • Two modes of operation, paint recovery with mixing or total waste • Sealed fluidization paint hopper • Automatic program for cleaning the tank and injectors with compressed air • Hopper powder level sensor assembly • Automatic refilling of the tray with paint from cardboard • Paint level sensor in refill box • An audible alarm alerts the operator when there is low paint in the box • The center is connected with the cabin control via ModBus protocol • Programmable powder suction valve to keep the powder center clean

Year of construction: 2020, condition: new, 7 "Touch Panel The large color touch panel looks aesthetically and is comfortable and intuitive to use. You will set all important parameters on it. Memory of 20 programs with 10 events It is possible to save up to 20 programs and activate up to 10 consecutive time-temperature events arranged in the heating curve. This is especially needed for more demanding processes. Information on gas / oil consumption The consumption is calculated based on the burner settings. This feature will allow you to estimate the cost of a given cycle, plan consumption and check personnel. Dual-channel recorder of USB cycle parameters Each furnace is equipped with a recorder that records all firing parameters, including two temperature channels - like in an airplane black box, on a USB flash drive. The system also enables the analysis of monthly / daily statements, including media consumption and performance. Each start of heating, opening the door, can be recreated, a few years back. Such a dedicated option is not offered by any manufacturer. It is a system developed from scratch by our programmers Automatic smoke exhaust chimney The chimney can be programmed to open a few minutes before the end of the firing in order to smoke the chamber. It can be remotely controlled from the panel, it does not need to be done mechanically as in most structures. Minute forecast until the end The cycle has started, how long will it end? calculating the heating dynamics, we will count it and show on the display how much longer it will take. To open it, just pull the door. The lock has adjustable pressure of the door, to close it just push it, the lock will catch the door and automatically pull it back. In order to minimize the effect of heating the hall when opening the door, a hood is installed above the door to remove some of the heat to other places. The MTS system was created to provide a real reading of the temperature of the furnace chamber. Standard measurement is based on one temperature measurement which is often wrong.MTS is a system of many sensors located in the outermost places of the chamber. The multi-zone heating system ensures a firing quality that has been so far unique. Hfodpsfz U Tqsfx Aacen Each normal oven has only one heating zone and only one temperature measurement! The multi zone heat system supports up to 8 independent heating zones in one oven. Each heating zone has as many as 3 temperature sensors! When there are temperature differences between zones, they are automatically equalized! The system helps to combat the problem when elements of different material thicknesses enter the furnace.

Year of construction: 2020, condition: new, PLC microprocessor control • HMI operator panel • Phases changed manually or automatically - temporarily • Two separate circuits for water and chemistry, closed circuit • Intelligent control - in the event of a power cut / sudden shutdown, no mixing of liquids possible The control box is made of IP54 technology User manual, Declaration of conformity, 12 months warranty. Hjdjf Aaalopfx Aacefn ROMER pressure washers use metal sheet that provides protection against chemicals. The washer walls protect against splashing, thanks to the closed chemistry loop, the process can be carried out with small amounts of chemistry. Due to the small amount of refrigerant required, it is easy to heat and cheaper to buy, it also allows you to wash large dimensions impossible to wash in bath tubs. Filtration system Thanks to the filtration system, the chemistry works in a closed circuit, 3 filters of different thickness are used, which prevent garbage and grease from entering the circulation. The chemistry is stored in heated stainless steel tanks from where it is fed by a pump under pressure to the lance Washing of dimensions The pressure washer allows washing of large elements, optionally has a rotating platform that allows rotation of the cleaned element, elements can be applied to it with a forklift or crane. High pressure pumps The car wash has two preparation phases, both treatments have separate sets of pipes, pumps, wires and guns to minimize mixing of these agents during phase change. Drains have separate valves that manage the return of funds. The carwash is equipped with a logic controller that controls all components. The chemistry is pumped up to 20 bar using a very durable, acid-resistant AISI304 pump with several stages, 3 kW. The rinsing phase uses a high pressure piston pump with ceramic pistons with a capacity of 3kW and provides 160 - 200 bar.

Year of construction: 2020, condition: new, Use of one photocell Using one photocell in the space of workpiece allows you to measure the length of the workpiece and, consequently, gives you the opportunity to turn on the guns when the item is in range, and to switch off the gun immediately after the workpiece is finished. The photocell is included in the standard equipment.Identification of details using special tags. A plate with identification holes is placed over the suspension. Based on this, the PLC controller in conjunction with the photocell recognizes the painted detail, turns on and off the guns in a timely manner - thus braking the energy and powder coating. Vertical detection of the detail of the workpiece. The use of light gates with detectors horizontally allows the PLC to analyze the vertical shape of the workpiece. Application of light gates with multiple sensors horizontally and vertically. Hjdpfefy T Arjx Aacsfn This solution allows precise measurement of the dimensions of the workpiece, which makes it possible also to manipulate the manipulators. Benefits of using gates and photocells The benefits of using photocells or light gates are primarily energy and powder savings. Eliminate painting of a zone in which there is no detail. With the use of light gates, precise control of the guns. Our lines can be optionally equipped with photocells, or light gates Using one photocell in the workpiece space allows you to measure the length of the workpiece and, consequently, gives you the ability to turn on guns when the item appears in their range, and turn off the gun immediately after the workpiece is finished.Identification of details using special tags. A plate with identification holes is placed over the suspension. Based on this, the PLC controller in conjunction with the photocell recognizes the painted detail, turns on and off the guns in a timely manner - thus saving the energy and powder.The use of light gates with detectors horizontally allows the PLC to analyze the vertical shape of the workpiece. The PLC counts the time in which the detail will appear in the gun space - allowing guns to be selectively switched on or off.Using of light gates with multiple sensors horizontally and vertically This solution allows precise measurement of the dimensions of the workpiece, which makes it possible also to adjusting the manipulators.The benefits of using photocells or light gates are primarily powder and energy savings Eliminate painting of a zone in which there is no detail With the use of light gates, precise control of the guns The PLC counts the time at which the detail should appear in the gun space - allowing guns to be selectively switched on or off.

Year of construction: 2020, condition: new, ROMER® is the largest producer of powder paint shops in Poland, and one of the largest in Europe. ROMER® is over 10,000 manufactured devices operating in over 45 countries around the world. Hodpfofzq Ryox Aacsfn ROMER® Produces single technological equipment for powder paint shops as well as complete fully automatic turnkey paint shops. ROMER® provides heating solutions for the aero and automotive industries for the largest concerns in the world. We provide warranty and post-warranty service of the devices we sell with a full range of spare parts.

Year of construction: 2020, condition: new, Washers Ultrasonic Baths for washing, phosphatizing, chromating, degreasing, removing paint coatings materials In ROMER Ultrasonic Washers, stainless steel is used which provides protection against acids. Bathtubs have an additional insulation wall, so they do not lose temperature and heat up faster. Good quality materials ensure long life of the vibrating elements. Heating system The heaters used in the ROMER bathtubs are made of the highest quality materials and are made of high temperature resistant ceramic elements. The heating system used ensures great thermal efficiency, hot water automatically mixes with cold water, heating the entire bathtub. Ultrasonic transducers Ultrasonic elements used in ROMER washers are installed in immersion modules, which better reflect vibrations and are exchangeable. The ultrasound range is 20-40kHz depending on the washed element, lower frequencies are used for large elements of high strength, lower for jewelry, sensitive mechanical systems, etc. All transducers are connected by high temperature resistant cables. Hfsdpsfz Aw Hefx Aacjn

Year of construction: 2020, condition: new, The ROMER company is also involved in the production of suspended transport systems. Cross traverses (Cross transports) are designed and manufactured for specific installations Oghxp Examples of equipment are presented below: Transport systems Depending on the customer's requirements, the transport systems can move on the floor or be hung on poles. - For comfortable solutions for manual installations, we recommend suspended crossbeams (cross transport). - For automated systems, chain conveyors are most often used that do not stop and are a great solution for companies that focus on quality and repeatability of the process. Hedpjfz Difefx Aacefn - For companies that make different items at the same time and have, for example, several cabins with different colors, flexible solutions are used with the use of a power-and-free conveyor. This is the most expensive solution.

Year of construction: 2020, condition: new, Pneumatic connection 1 " • Controls 7 "color touch panel • Paint tank capacity 6-7 kg • Air consumption during painting 15Nm3 / h • Air consumption for cleaning 350Nm3 / h • Hopper paint level sensor Yes • Ultrasonic screener Yes • Powder injectors up to 12 pcs Description Hjdpfxjfz Dkne Aacofn • RP-01 pump for topping up the paint with fresh paint from cardboard • Two modes of operation, paint recovery with mixing or total waste • Sealed fluidization paint hopper • Automatic program for cleaning the tank and injectors with compressed air • Hopper powder level sensor assembly • Automatic refilling of the tray with paint from cardboard • Paint level sensor in refill box • An audible alarm alerts the operator when there is low paint in the box • The center is connected with the cabin control via ModBus protocol • Programmable powder suction valve to keep the powder center clean

Year of construction: 2020, condition: new, ROMER manipulators are characterized by quiet operation. They can be widely used both with simple, as well as complex multidimensional processes They are programmed using a PLC controller Working with long and short strokes The toothed belt transmission ensures quiet operation Maintenance-free AC motor Narrow column design for space saving. The robust construction of the manipulators ensures great possibilities and high stability. Hsdpfx Aefz Dmmeacsfn The manipulator is equipped with a 7 "touch panel or is externally controlled via the ModBus protocol with RJ45 cables

Year of construction: 2020, condition: new, DESCRIPTION The demineralized water station is used to produce the so-called demi water using ion exchange technology. The station consists of 3 columns Strongly acid cation exchanger working in the sodium cycle, Strongly basic anion exchanger working in the chloride cycle, Carbon filter Our RDI-2 / RDI-4 demineralization stations are equipped with fully automatic control heads. Rouezts Hfjdpefz Dwzofx Aacsn The columns are made of AISI316L steel

Year of construction: 2020, condition: new, Pneumatic connection 1 " • Controls 7 "color touch panel • Paint tank capacity 6-7 kg Hedsfz U Rropfx Aacefn • Air consumption during painting 15Nm3 / h • Air consumption for cleaning 350Nm3 / h • Hopper paint level sensor Yes • Ultrasonic screener Yes • Powder injectors up to 12 pcs Description • RP-01 pump for topping up the paint with fresh paint from cardboard • Two modes of operation, paint recovery with mixing or total waste • Sealed fluidization paint hopper • Automatic program for cleaning the tank and injectors with compressed air • Hopper powder level sensor assembly • Automatic refilling of the tray with paint from cardboard • Paint level sensor in refill box • An audible alarm alerts the operator when there is low paint in the box • The center is connected with the cabin control via ModBus protocol • Programmable powder suction valve to keep the powder center clean

Year of construction: 2020, condition: new, Gravity heating system Thanks to the use of a gravity heating system in SPARK series gravity furnaces, we can boast of a good result of temperature homogeneity, our tests have shown that the air temperature uniformity in our gravity furnaces, with the appropriate arrangement of elements, does not exceed ± 5 ° C! We owe the result to our heating element assembly technology. Rapid heating SPARK series gravity furnaces have specially designed heaters that quickly give off heat, thanks to which our furnaces heat up quickly. We owe rapid heating to the applied seals and insulations, the specially profiled gasket does not contain asbestos and is safe for the user. Optimization of the insulation, no contact between the furnace chamber and the casing minimizes heat loss and saves power. Depending on the model, our furnaces heat up to 8 ° C per minute. Hsdpsfy T R Dofx Aacjfn Transport system The SPARK series ovens are equipped with two bottom transport carriages as standard. In response to the market demand for inexpensive solutions, we have developed a manual bottom transport system that allows you to transport large dimensions with a minimum of force. Our system allows for optimal use of the entire surface of the furnace and ensures high cleanliness of the painted elements. Thanks to the use of two trolleys, the trolley moving around the hall does not contaminate the interior of the furnace. The top trolley is used to enter the furnace itself. The use of one trolley causes the introduction of contaminants from the floor into the furnace chamber, our system eliminates this problem.

Year of construction: 2020, condition: new, Pneumatic connection 1 " • Controls 7 "color touch panel • Paint tank capacity 6-7 kg • Air consumption during painting 15Nm3 / h • Air consumption for cleaning 350Nm3 / h • Hopper paint level sensor Yes • Ultrasonic screener Yes • Powder injectors up to 12 pcs Description • RP-01 pump for topping up the paint with fresh paint from cardboard • Two modes of operation, paint recovery with mixing or total waste • Sealed fluidization paint hopper • Automatic program for cleaning the tank and injectors with compressed air • Hopper powder level sensor assembly • Automatic refilling of the tray with paint from cardboard • Paint level sensor in refill box • An audible alarm alerts the operator when there is low paint in the box • The center is connected with the cabin control via ModBus protocol • Programmable powder suction valve to keep the powder center clean Hfjdjfz Dkgepfx Aacsn

Year of construction: 2020, condition: new, Washers Ultrasonic Baths for washing, phosphatizing, chromating, degreasing, removing paint coatings materials Hfjdjfz Dtzepfx Aacen In ROMER Ultrasonic Washers, stainless steel is used which provides protection against acids. Bathtubs have an additional insulation wall, so they do not lose temperature and heat up faster. Good quality materials ensure long life of the vibrating elements. Heating system The heaters used in the ROMER bathtubs are made of the highest quality materials and are made of high temperature resistant ceramic elements. The heating system used ensures great thermal efficiency, hot water automatically mixes with cold water, heating the entire bathtub. Ultrasonic transducers Ultrasonic elements used in ROMER washers are installed in immersion modules, which better reflect vibrations and are exchangeable. The ultrasound range is 20-40kHz depending on the washed element, lower frequencies are used for large elements of high strength, lower for jewelry, sensitive mechanical systems, etc. All transducers are connected by high temperature resistant cables.

Year of construction: 2020, condition: new, PLC microprocessor control Hfodpefz Dvvofx Aacjn • HMI operator panel • Phases changed manually or automatically - temporarily • Two separate circuits for water and chemistry, closed circuit • Intelligent control - in the event of a power cut / sudden shutdown, no mixing of liquids possible The control box is made of IP54 technology User manual, Declaration of conformity, 12 months warranty. ROMER pressure washers use metal sheet that provides protection against chemicals. The washer walls protect against splashing, thanks to the closed chemistry loop, the process can be carried out with small amounts of chemistry. Due to the small amount of refrigerant required, it is easy to heat and cheaper to buy, it also allows you to wash large dimensions impossible to wash in bath tubs. Filtration system Thanks to the filtration system, the chemistry works in a closed circuit, 3 filters of different thickness are used, which prevent garbage and grease from entering the circulation. The chemistry is stored in heated stainless steel tanks from where it is fed by a pump under pressure to the lance Washing of dimensions The pressure washer allows washing of large elements, optionally has a rotating platform that allows rotation of the cleaned element, elements can be applied to it with a forklift or crane. High pressure pumps The car wash has two preparation phases, both treatments have separate sets of pipes, pumps, wires and guns to minimize mixing of these agents during phase change. Drains have separate valves that manage the return of funds. The carwash is equipped with a logic controller that controls all components. The chemistry is pumped up to 20 bar using a very durable, acid-resistant AISI304 pump with several stages, 3 kW. The rinsing phase uses a high pressure piston pump with ceramic pistons with a capacity of 3kW and provides 160 - 200 bar.

Year of construction: 2020, condition: new, DESCRIPTION The demineralized water station is used to produce the so-called demi water using ion exchange technology. The station consists of 3 columns Strongly acid cation exchanger working in the sodium cycle, Strongly basic anion exchanger working in the chloride cycle, Carbon filter Hfodpefz I Nhefx Aacjn Our RDI-2 / RDI-4 demineralization stations are equipped with fully automatic control heads. Rouezts The columns are made of AISI316L steel

Year of construction: 2020, condition: new, DESCRIPTION The demineralized water station is used to produce the so-called demi water using ion exchange technology. The station consists of 3 columns Strongly acid cation exchanger working in the sodium cycle, Strongly basic anion exchanger working in the chloride cycle, Carbon filter Our RDI-2 / RDI-4 demineralization stations are equipped with fully automatic control heads. Rouezts The columns are made of AISI316L steel Hfsdpsfz I Syjfx Aacjn

Year of construction: 2020, condition: new, ROMER® deals with the production of single technological equipment for powder coating plants as well as complete fully automatic turnkey coating plants. ROMER® provides heating solutions for the aero and automotive industries for the largest corporations in the world. We provide warranty and post-warranty service for devices sold by us with a full range of spare parts. the trawl applied to a poorly prepared surface will fall off or corrode after a short period of time. Ensuring the best coating is essentially good degreasing - which is the basis of any painting. The coating of a poorly degreased detail will fall off after a very short time. After degreasing, the next step is to tear down the outer coating of the detail, which improves paint adhesion, e.g. when bending sheet metal, and protection, e.g. with a phosphate layer, which in turn will prolong corrosion resistance. There are many solutions that solve the above issues. What is the most important thing in a powder coating shop? You probably don't have experience with the applicator. Nothing more wrong, even the best applicator will not help you if your oven has bad temperature distributions, in the place where the element is overheated, the paint will discolor and where not heated, the paint will fall off. First of all, the stove is the most important. Oil, gas or electric furnace? You don't know how to power your stove? how is cheaper what does this involve? What are the operating costs? We will try to answer your questions. Hfodefz Ndyspfx Aacjn Depending on the customer's requirements, transport systems can move on the floor or be suspended on poles. - For comfortable solutions for manual installations, we recommend suspended cross traverses (cross transport). - For automated systems, chain conveyors are most often used that do not stop and are a great solution for companies that focus on quality and repeatability of the process. - For companies that make different items at the same time and have e.g. several cabins with different colors, flexible solutions with the use of the power-and-free conveyor are used. This is the most expensive solution.

Year of construction: 2020, condition: new, Description Automatic sprinkling chamber is a solution that allows you to reduce costs, improve quality and increase the efficiency of the surface preparation process. The automatic sprinkling chamber is equipped with a set of spray pumps, it was designed so that as little liquid as possible after the process migrates to subsequent processes, thus saving money and improving the quality of washing. This is very important, because apparent savings in systems made without the use of these solutions can generate in the future much higher costs associated with chemistry and waste disposal which will simply be more. Attention should also be paid to problems with maintaining the required bath parameters. Research and development work allowed us to develop a sprinkling chamber with the function of drying details (option) with hot air blown by a set of fans after the washing process. The sprinkling chamber is equipped with an advanced system for creating your own macro programs, which can consist of 10 steps each, depending on the number of tanks, processes can be repeated, their order can be changed, etc. Each tank has its own unique icon and name, enabling the operator to work intuitively. Optionally, the tanks can be equipped with bath replenishment systems, which can be performed e.g. between processes or at the end of the cycle. Hjdpfx Asfy T Szsacefn • Control installed on the swivel arm for better access • PLC microprocessor control • 7 "touch operator panel • Very large number of nozzles, compared to other solutions • (Option) The possibility of drying details after the washing process • The ability to create your own advanced programs • Advanced damper system made of acid-resistant sheet metal, double protected by limit switches • Tight closing and full flap opening control system • To minimize fluid mixing, separate pipelines, nozzles, tanks for each treatment • Intelligent control - in the event of a power cut / sudden shutdown, no mixing of liquids possible • Fully automatic operation/ Prices are given in the catalog

Year of construction: 2020, condition: new, 7 "Touch Panel The large color touch panel looks aesthetically and is comfortable and intuitive to use. You will set all important parameters on it. Memory of 20 programs with 10 events It is possible to save up to 20 programs and activate up to 10 consecutive time-temperature events arranged in the heating curve. This is especially needed for more demanding processes. Information on gas / oil consumption The consumption is calculated based on the burner settings. This feature will allow you to estimate the cost of a given cycle, plan consumption and check personnel. Dual-channel recorder of USB cycle parameters Each furnace is equipped with a recorder that records all firing parameters, including two temperature channels - like in an airplane black box, on a USB flash drive. The system also enables the analysis of monthly / daily statements, including media consumption and performance. Each start of heating, opening the door, can be recreated, a few years back. Such a dedicated option is not offered by any manufacturer. It is a system developed from scratch by our programmers Automatic smoke exhaust chimney The chimney can be programmed to open a few minutes before the end of the firing in order to smoke the chamber. Hfedefz Anpjpfx Aacon It can be remotely controlled from the panel, it does not need to be done mechanically as in most structures. Minute forecast until the end The cycle has started, how long will it end? calculating the heating dynamics, we will count it and show on the display how much longer it will take. To open it, just pull the door. The lock has adjustable pressure of the door, to close it just push it, the lock will catch the door and automatically pull it back. In order to minimize the effect of heating the hall when opening the door, a hood is installed above the door to remove some of the heat to other places. The MTS system was created to provide a real reading of the temperature of the furnace chamber. Standard measurement is based on one temperature measurement which is often wrong.MTS is a system of many sensors located in the outermost places of the chamber. The multi-zone heating system ensures a firing quality that has been so far unique. Each normal oven has only one heating zone and only one temperature measurement! The multi zone heat system supports up to 8 independent heating zones in one oven. Each heating zone has as many as 3 temperature sensors! When there are temperature differences between zones, they are automatically equalized! The system helps to combat the problem when elements of different material thicknesses enter the furnace.

Year of construction: 2020, condition: new, PLC microprocessor control • HMI operator panel • Phases changed manually or automatically - temporarily • Two separate circuits for water and chemistry, closed circuit • Intelligent control - in the event of a power cut / sudden shutdown, no mixing of liquids possible The control box is made of IP54 technology Hfjdpfx Aaefz Ax Socon User manual, Declaration of conformity, 12 months warranty. ROMER pressure washers use metal sheet that provides protection against chemicals. The washer walls protect against splashing, thanks to the closed chemistry loop, the process can be carried out with small amounts of chemistry. Due to the small amount of refrigerant required, it is easy to heat and cheaper to buy, it also allows you to wash large dimensions impossible to wash in bath tubs. Filtration system Thanks to the filtration system, the chemistry works in a closed circuit, 3 filters of different thickness are used, which prevent garbage and grease from entering the circulation. The chemistry is stored in heated stainless steel tanks from where it is fed by a pump under pressure to the lance Washing of dimensions The pressure washer allows washing of large elements, optionally has a rotating platform that allows rotation of the cleaned element, elements can be applied to it with a forklift or crane. High pressure pumps The car wash has two preparation phases, both treatments have separate sets of pipes, pumps, wires and guns to minimize mixing of these agents during phase change. Drains have separate valves that manage the return of funds. The carwash is equipped with a logic controller that controls all components. The chemistry is pumped up to 20 bar using a very durable, acid-resistant AISI304 pump with several stages, 3 kW. The rinsing phase uses a high pressure piston pump with ceramic pistons with a capacity of 3kW and provides 160 - 200 bar.

Year of construction: 2020, condition: new, The ROMER company is also involved in the production of suspended transport systems. Cross traverses (Cross transports) are designed and manufactured for specific installations Hedpfsfz Dibsx Aacofn Oghxp Examples of equipment are presented below: Transport systems Depending on the customer's requirements, the transport systems can move on the floor or be hung on poles. - For comfortable solutions for manual installations, we recommend suspended crossbeams (cross transport). - For automated systems, chain conveyors are most often used that do not stop and are a great solution for companies that focus on quality and repeatability of the process. - For companies that make different items at the same time and have, for example, several cabins with different colors, flexible solutions are used with the use of a power-and-free conveyor. This is the most expensive solution.

Year of construction: 2020, condition: new, Pneumatic connection 1 " • Controls 7 "color touch panel • Paint tank capacity 6-7 kg Hfedpfsfz U Sajx Aacjn • Air consumption during painting 15Nm3 / h • Air consumption for cleaning 350Nm3 / h • Hopper paint level sensor Yes • Ultrasonic screener Yes • Powder injectors up to 12 pcs Description • RP-01 pump for topping up the paint with fresh paint from cardboard • Two modes of operation, paint recovery with mixing or total waste • Sealed fluidization paint hopper • Automatic program for cleaning the tank and injectors with compressed air • Hopper powder level sensor assembly • Automatic refilling of the tray with paint from cardboard • Paint level sensor in refill box • An audible alarm alerts the operator when there is low paint in the box • The center is connected with the cabin control via ModBus protocol • Programmable powder suction valve to keep the powder center clean

Year of construction: 2020, condition: new, ROMER manipulators are characterized by quiet operation. Bmt7r28v0e They can be widely used both with simple, as well as complex multidimensional processes They are programmed using a PLC controller Working with long and short strokes Hfedpfx Aaof Aad Nscsn The toothed belt transmission ensures quiet operation Maintenance-free AC motor Narrow column design for space saving. The robust construction of the manipulators ensures great possibilities and high stability. The manipulator is equipped with a 7 "touch panel or is externally controlled via the ModBus protocol with RJ45 cables