Used Powder Coating for sale (2,745)

Year of construction: 2018, condition: used, The year of manufacture refers to the final acceptance of the system; individual components may differ in age. Workpiece dimensions up to a maximum of L x W x H: 8,000 x 2,000 x 2,000 mm, maximum crossbeam load: 2,000 kg/carriage, material: steel. Bwsdpfx Asy T Nzdem Ron Pos. 1: Washing booth, Jumbo-Clean with stainless steel interior for degreasing/phosphatizing of steel, either automated or with manual spray lance. Pos. 2: 1 set of belt filters. Pos. 3: 1 automatic spray ring for the Jumbo-Clean washing booth, including a central lance. Pos. 4: 1 fresh water treatment system. Pos. 5: 1 manual conveyor with 1 electric cross-travel carriage. Pos. 6: 1 lifting/lowering station, Jumbo-Lift 2000, integrated into the cross-travel carriage. Pos. 7: 1 indirect gas-heated flash-off oven/powder drying oven/wet coating drying oven, door opening W x H: 2,800 x 3,100 mm, clear length: 9,500 mm, overall W/H/L approx.: 4,000/5,000/10,000 mm. Pos. 8: 1 end-face powder coating extraction system for an on-site painting booth for spraying and drying operations. Pos. 9: 1 manual coating unit, OptiFlex(R)2. Pos. 10: 1 structure for on-site steel construction. Pos. 11: Control cabinet.

Condition: ready for operation (used), Year of construction: 2012, functionality: fully functional, Automatic Wagner powder coating plant, year of manufacture 2012 - Wagner SuperCube booth - Wagner SuperCenter powder supply system - PBS filter and cyclone 18,000 m³/h - STS CO2 extinguishing system - Pre- and post-coating stations with scissor lift platforms Bjdpfxjy Icfxe Am Rown - Clearance dimensions (H): 2500 mm, (W): 1000 mm - 12 automatic guns + manual powder coating units Disassembly by arrangement at our facility in Bad Laer! Price upon request

Condition: new, Year of construction: 2026, functionality: fully functional, total length: 2,000 mm, total width: 2,100 mm, power: 3 kW (4.08 HP), compressed air connection: 6.5 bar, volume flow: 6 m³/h, Open spray stand 2x2.1x2.2 The overspray during powdering is collected via the suction unit. The powder spray stand is supplied on castors and is therefore mobile. - The suction unit is equipped with a 60 l powder container (rollbar). - There are 4 filters in the extraction unit as the 1st stage. - The absolute filter is located above the booth. Bjdpfx Aefhv Tqjm Rjwn 1 Dimensions of the powder stand Width 2,000 mm Depth 2,100 mm Height 2,200 mm 2 fans 1 pc. 6,000 m³/h Electric motor 3.0 kW 3 Filter Ø 325x600 4 pcs. type filter cartridges 4 Electromagnetic valves 2 pcs. 1" "Turbo" Italy 5 Absolute filter 1 pc. type pocket filter

Condition: new, Year of construction: 2026, functionality: fully functional, insulation material: Mineralwolle 75 kg/m³, insulation thickness: 150 mm, 1. powder coating booth, open spray booth The overspray during powder coating is collected by the suction unit. The powder spray booth is supplied on castors and is therefore mobile. - The extraction unit is equipped with a 60 l powder container (rollbar). - There are 4 filters in the extraction unit as the 1st stage. - The absolute filter is located above the booth. 1 Dimensions of the powder level Bwjdpjffwfxsfx Am Rjn Width 2,450 mm Depth 2,350 mm Height 2,700 mm 2 fans 1 pc. 6,000 m³/h Electric motor 3.0 kW 3 Filter Ø 325x800 [mm] 4 pcs. type filter cartridges 4 Electromagnetic valves 2 pcs. 1" "Turbo" Italy 5 Absolute filter 1 pc. type pocket filter 2. powder combustion furnace 1 Internal dimension length 4,000 mm 2 Inner dimension width 1,500 mm 3 Internal height 2,200 mm 4 External dimension incl. thermoblock length 5,250 mm 5 External dimension incl. thermoblock width 2,050 mm 6 External dimension incl. thermoblock height 2,530/2,750 mm 3. switch cabinet 4 Manual conveyor system The "Mantion system" conveyor technology is designed for max. 250 kg per product carrier and 750 kg/ trolley.

Condition: new, Year of construction: 2026, functionality: fully functional, total length: 30,000 mm, total height: 4,300 mm, total width: 6,500 mm, workpiece weight (max.): 100 kg, temperature: 220 °C, heating capacity: 80 kW (108.77 HP), workpiece height (max.): 1,200 mm, workpiece length (max.): 2,500 mm, insulation material: Mineralwolle 75 kg/m³, insulation thickness: 150 mm, workpiece width (max.): 800 mm, The continuous system consists of the following components: Bwodoum Uflspfx Am Rsn Chemical pre-treatment by spraying Dryer Powder coating system Powder curing oven Conveying technology (cycle process) Electrical control system

Condition: new, Year of construction: 2026, Starter Packages Powder Coating Starter sets or individually designed packages for starting your own business in surface technology, e.g. for coating alloy wheels: The package includes two sample configurations for entering powder coating or expanding an existing business. Our focus is on customized consulting tailored to the customer’s budget and requirements. Modifications and special requests are standard with us. Proven, robust and low-maintenance technology is at the center of our offer. Set 1: - Powder curing oven, internal dimensions 2,000 x 1,900 x 2,000 mm - 150 mm thick mineral wool wall insulation for energy-efficient and cost-saving operation - 36 kW thermal output for rapid heat-up time - Oil, gas, or electric heating options - 6,000 m³/h recirculating air (2.2 kW) for efficient heat transfer to workpieces - Up to 220°C - Powder coating booth (open spray booth) Powder booth dimensions: - Width: 2,100 mm - Depth: 2,000 mm - Height: 2,200 mm - Fan: 6,000 m³/h, electric motor 3.0 kW for a clean working environment - Filters: 4 units, ø 325x600, cartridge type with interval-controlled self-cleaning - Secondary filtration via pocket filters - Powder coating system Wagner, manual system “Sprint 2 B” - Latest model from premium manufacturer Wagner for optimal coating results (other brands available upon request) - Corona manual gun - PEM-C4 Ergo - EPG-Sprint control unit - Powder feed system with Fluid Crown ST 550/10 - Powder injector PI-F1 - Equipment trolley with vibrating table Set 2: - Powder curing oven, internal dimensions 1,500 x 1,200 x 1,750 mm - 150 mm thick mineral wool wall insulation for energy-efficient and cost-saving operation - 14 kW thermal output for rapid heat-up time - Electric heating - 2,600 m³/h recirculating air (1.1 kW) for efficient heat transfer to workpieces - Up to 220°C - Powder coating booth (open spray booth) Powder booth dimensions: - Width: 1,200 mm - Depth: 1,100 mm - Height: 2,380 mm - Fan: 2,500 m³/h, electric motor 1.1 kW for a clean working environment - Filters: 2 units, ø 325x600, cartridge type with interval-controlled self-cleaning - Secondary filtration via pocket filters Bedpfobqk Nbex Am Rjwn - Powder coating system Wagner, manual system “Sprint 2 B” - Latest model from premium manufacturer Wagner for optimal coating results (other brands available upon request) - Corona manual gun - PEM-C4 Ergo - EPG-Sprint control unit - Powder feed system with Fluid Crown ST 550/10 - Powder injector PI-F1 - Equipment trolley with vibrating table

Year of construction: 2013, condition: used, functionality: fully functional, machine/vehicle number: GE-KEK-100L, Complete powder coating system for sale, including chemical pretreatment cabin, powder coating booth, and curing oven. The system is fully operational, well-maintained, and immediately available. Ideal for metal fabrication workshops, small industrial producers, or powder coating subcontractors. The equipment complies with EU industrial standards and features comprehensive electrical control systems. Included equipment: 1️⃣ Chemical Pretreatment Cabin Manual chemical pretreatment spray unit for surface preparation before powder coating. - Cabin dimensions: 1600 × 1600 × 2200 mm - Chemical tank capacity: approx. 800 L - Pump / spray unit: ST84 HE - Heating elements: 2 × 6 kW - Water temperature: 45–60°C - Motor power: approx. 1.5 kW - Electrical connection: 3×380/220 V - Closed circulation system - Chemical-resistant design 2️⃣ Industrial Powder Coating Booth - External dimensions: 1850 × 1600 × 2600 mm - Airflow: 3,000 m³/h - Motor: approx. 1.5 kW - Filter cartridges: 2 pcs with automatic cleaning - Airflow speed: 0.2–0.5 m/s - Maximum suspension size: 250 × 1000 mm - Spray opening: 1100 × 1100 mm Included equipment: - Extraction ventilation with silencer - Compressed air treatment unit - Automatic filter cleaning system - Powder recycling tank - EU-standard control cabinet - Condition: good technical condition, regularly serviced 3️⃣ Industrial Walk-in Powder Curing Oven - Internal dimensions: 1300 × 1300 × 2200 mm - Working temperature: 180–200°C - Typical curing time: 15–25 minutes - Heating capacity: 2 × 12 kW (electric) - Circulated air: 1,250 m³/h - Exhaust air: 100 m³/h - Motor power: approx. 1.5 kW - Insulation thickness: 150 mm - Year of manufacture: 2013 Included equipment: - Insulated chamber with door - Circulation fan system - Heating elements - Overheat protection Bwedpsygg Rnefx Am Rsn - Airflow sensor - EU control cabinet - Steel base frame Condition: Excellent working order, complete documentation available General information - System type: Powder coating line - Condition: Very good - Year: 2013 - Documentation: Available - Operational status: Fully functional - Availability: Immediately available Price 💰 19,900 EUR (complete system) Location Hungary – EU Ideal for: - Metal fabrication workshops - Small powder coating facilities - Industrial maintenance workshops - Subcontract coating services

Condition: used, Year of construction: 2018, Wagner electrostatic powder coating system for enamel application, year 2018, serial number 30210, with a touch screen control panel, consisting of: Bedpfxey Tn Ats Am Rewn • 1 PVC spray booth with overall dimensions of length x width x height: 3200 x 2130 x 4000 mm • Dimensions of the part entry/exit opening: 1000 x 1000 mm • 1 HERDING filter (cyclone) with automatic powder recovery • 1 shaker for powder suspension with extraction and powder recovery • 1 EP powder feeder with 32 pumps (injectors) • 12 automatic spray guns, model PEA-C2, for enamel application, with a double blade head • 9 universal EPG/S2 control units for powder guns • 1 GCA compressed air treatment unit used in the system (heating/humidification) • 1 overhead monorail transport system, 35 m long, serving the spray booth. The line is located at the parent company in Italy, near the town of Pordenone. Direct contact is possible, upon prior arrangement.

Year of construction: 2014, condition: used, Used powder coating line. Shutdown in 2024. Bodpfx Ajvxrm Uom Rown - container mixer Mixaco, typ CM1000-MT, with 4 x ss tank 800Ltr new.: 2014 - extruder Coperion, ZSK 43 MV, new.: 2014 - SBS Cooling Conveyer 800mm wide x 5000mm long - mill Hosokawa Alpine, typ ACM40 EC CL, new: 2014 - dosing device Gericke, typ GL D 7, new: 2014 - feeding device Hosokawa, new: 2014 - pressure filter Hosokawa Alpine, new: 2014 - stainles steel cyclone diam.: 500 mm - 2x rotary screen AZO, typ E 240 - pocket filter, with 45 kW el. motor - cooling unit Climaveneta typ NX/K 0914P - cooling unit Climaveneta typ NX/K 0552P

Condition: new, Year of construction: 2026, power: 80 kW (108.77 HP), temperature: 230 °C, inner dimension length: 3,200 mm, inner dimension width: 1,400 mm, inner dimension height: 2,370 mm, total length: 3,960 mm, total width: 1,880 mm, total height: 3,370 mm, control type: PLC-controlled, Equipment: CE marking, Powder coating Oven (Oil/Gas) Internal dimensions LxWxH: 3200 x 1400 x 2370 mm External dimensions LxWxH: 3960 x 1880 x 3370 mm Fuel: Oil or GAS, buyer can choose the burners Heating power: 80 kW (1 burner) Maximum working temperature: 230C; Heat resistant recirculating fans: 1 x 1,1 kW 10""Touch screen“ control Functions: preheating, degassing, drying, polymerisation Temperature sensors in working chamber: 2 vnt. Two wing doors on one side Ready for 4 rails (rails not included) Key features: Solid construction Special frame design reduce heat loss Removable side panels for easy maintenance Equipped with special located ventilation slots - keep insulation material in order Stainless steel panels in Heat exchanger zone Inhouse engineered heat resistant fans - cool, quiet, long - life Doors equipped with explosion proof, adjustable lathes Special design door handles for lower heat transfer Reliable Italian RIELLO burners Control Features 10"touch screen control Standard programs: Preheating, Degassing, Curing, Drying Stores multiply curing recipes Integrated safety features HNS - heat management system, measures air temperature in few points. prevents overheating of curing parts Drying mode - time control exhaust and blow-in fresh air Vent mode - for higher finish quality Delivery in 2 weeks after payment WARRANTY: 12 month We can organise delivery accross the EU for speacial price. PRICES are EXCLUDING VAT. Bodpfxoy Uxrne Am Rjwn WE ARE LOOKING FOR SALES PARTNERS

Condition: new, Year of construction: 2026, temperature: 230 °C, inner dimension length: 3,800 mm, inner dimension width: 1,600 mm, inner dimension height: 2,270 mm, total length: 4,560 mm, total width: 2,080 mm, total height: 3,270 mm, control type: PLC-controlled, Equipment: CE marking, Internal dimensions LxWxH: 3800 x 1600 x 2270 mm External dimensions LxWxH: 4560 x 2080 x 3270 mm Fuel: Oil or GAS, buyer can choose the burners Heating power: 160 kW (2 burners in total) Maximum working temperature: 230 o C; Heat resistant recirculating fans: 2 x 1,1 kW 10""Touch screen“ control Functions: preheating, degassing, drying, polymerisation Temperature sensors in working chamber: 2 vnt. Two wing doors on both sided (tunnel) Ready for 5 rails (rails not included) Key features: Solid construction Special frame design reduce heat loss Removable side panels for easy maintenance Equipped with special located ventilation slots - keep insulation material in order Stainless steel panels in Heat exchanger zone Inhouse engineered heat resistant fans - cool, quiet, long - life Doors equipped with explosion proof, adjustable lathes Special design door handles for lower heat transfer Reliable Italian RIELLO burners POWDER COATING OVEN FLOWSYNC Control Features Bjdpfx Aoy Ud H Rem Rown 10"touch screen control Standard programs: Preheating, Degassing, Curing, Drying Stores multiply curing recipes Integrated safety features HNS - heat management system, measures air temperature in few points. prevents overheating of curing parts Drying mode - time control exhaust and blow-in fresh air Vent mode - for higher finish quality WE ARE LOOKING FOR SALES PARTNERS

Condition: good (used), Year of construction: 2018, functionality: fully functional, Gema Year of manufacture: 2018 Equipped with 6 automatic guns, 2 manual spray guns Max. pass-through dimensions: L x H x W, 3m x 2m x 1.1m Magic Compact BA04 Color change system Magic Compact BA4 OptiCenter OC2 Powder coating device OptiMatic AS06-8P Lifting equipment ZA7-23 Mono-cyclone 24,000 [Nm3/h] from Therma Afterfilter exhaust air volume 24,000 [Nm3/h] STS fire suppression system Caldan Bwsdpfjy Al T Iox Am Rjn Overhead conveyor system Power & Free by Caldan Year of manufacture: 2018 Approx. 120 linear meters, with 12 product carrier trolleys, each 3 meters Custom built by Protaurus Gas-heated curing oven by Protaurus Year of manufacture: 2018 Weishaupt burner type WG40N/1-A, 500 kW output Complete with control system and accessories Without insulation material, oven casing needs to be overhauled Complete system by Gema and Caldan professionally packed Professional reassembly by Gema and Caldan prepared Layout attached Transportation costs, reassembly, and commissioning to be borne by the buyer

Condition: new, functionality: fully functional, Year of construction: 2026, Detailed Specification: - Internal dimensions: 5500 × 1500 × 2300 mm (L × W × H) - External dimensions: 5700 × 1900 × 2700 mm (L × W × H) - Entrance doors: Double-wing, 1700 × 2300 mm (W × H) - Wall panels: Thickness 100 mm, width 950 mm, tongue-and-groove structure; steel sheet 0.5 mm with mineral wool insulation inside Bwedpfx Ajxna U Uem Ren - Box: Panels 100 mm thick, filled with mineral wool - Heating system: RIELLO oil burner model 40G20; heating capacity 200,000 Kcal/h; heat exchanger made of 2 mm stainless steel - Maximum heating output: 200,000 Kcal/h, total 1 set - Roof: Panels 100 mm thick with mineral wool insulation inside - Control system: Heating control, time setting, fault indicator, emergency stop, hour counter, temperature limit regulator, total operating hours display - Total power: 6 kW - Overhead conveyor system: 4 tracks; maximum load 400 kg each We can manufacture ovens of any required dimensions. We provide complete systems including transport traverses, spray walls, and powder coating guns — as shown in the photos.

Year of construction: 2025, condition: new, Curing ovens shown in the photos can vary in price depending on size, configuration, and optional features. 💡📏⚙️ Bwodpjfx Nfmefx Am Ren At ROMER, we manufacture both standard models and fully bespoke solutions, tailored to your process requirements. 🏭✅ Tell us your part size, line capacity, curing profile, and available space - and we will propose the best setup and the options that actually improve daily performance. 🔥🎯 🧠📡 Control and monitoring Live process control for temperature, time, airflow, and modes - with alarms and saved recipes for repeatable cycles. 🔁✅ 🔥🧩 Heating module Fast heat-up and stable temperature thanks to efficient heating elements and quick energy transfer. ⚡🌡️ 🌀💨 Air circulation Uniform airflow reduces temperature differences for consistent coating quality. 🎯✅ 🧱❄️ Insulation and design Smart chamber construction minimizes heat loss - faster reaching setpoint, lower consumption. ♻️📉 🛡️⚠️ Safety and certification Sensors, interlocks, and protection logic increase safety and reliability. 🔒👷 ⚡💰 High efficiency Optimized heat transfer and reduced losses mean real operating savings. 📉🔥 ⏰🤖 Automatic start Programmable schedule - automatic preheating before the shift for smoother production starts. ⏱️✅ 🚪🔒 Self-latching doors + intelligent chimney Prevents accidental opening, chimney activates only when needed for safer operation. 🧯✅ 🌿🔋 ECO mode Low-energy standby when idle - fuel consumption reduction up to 20% (depending on process). 🌱📉 👀💡 View and lighting Inspection without opening the door - fewer temperature drops, easier supervision. ✨👁️ 🛤️🔥 Guide rails + automatic hood Heat hood runs only during loading to reduce temperature loss, automatic rail infeed improves ergonomics and loading speed. 🙌⚙️ 🎛️🌡️ MULTI-ZONE HEAT Independent zone control for uniform curing of parts with different mass and geometry. 🧩✅ 🧠♨️ MTS system Heating elements mounted without thermal bridges - higher efficiency and faster time to set temperature. ⚡⏱️ 2-in-1 🧱↔️🧱 Split chamber Movable partition for two independent zones - drying and curing in one unit for maximum flexibility. 🚀🔁 🎚️🌀 VFD ventilation Variable fan speed based on chamber conditions - better control and lower electricity use. ⚙️💡

Year of construction: 2020, condition: new, Transport systems Depending on the customer's requirements, transport systems can move on the floor or be suspended on poles. - For comfortable solutions for manual installations, we recommend suspended cross traverses (cross transport). - For automated systems, chain conveyors are most often used that do not stop and are a great solution for companies that focus on quality and repeatability of the process. - For companies that make different items at once and have e.g. several cabins with different colors, flexible solutions with the use of the power-and-free conveyor are used. This is the most expensive solution. All installations are made to measure, depending on the customer's requirements. Continuous suspended chain transport systems are designed and manufactured to individual customer orders. In this system, it is also possible to make bottom conveyor systems on which details are placed, e.g. flower pots, rims (photo). ROMER also manufactures suspended transport systems. Crossbeams (cross transports) are designed and made for the needs of specific installations The use of one photocell The use of one photocell in the space of the detail allows you to measure its length and, consequently, gives the option of switching on the guns when the detail appears in their range, and switching off the guns immediately after painting the detail. The photocell is standard equipment. Identification of details by means of special markers. Above the sling there are plates with identification holes. Based on them, the PLC controller in conjunction with the photocell recognizes the painted detail, turns the guns on and off in good time - thus saving energy and powder paint. Vertical shape detection. The use of light gates with horizontal detectors allows the PLC controller to analyze the shape of a detail vertically. The PLC controller counts the time in which the detail should appear in the gun space - thanks to this it is possible to selectively turn the guns on or off. Using light gates with multiple sensors horizontally and vertically. This solution allows precise measurement of workpiece dimensions, thanks to which it is also possible to control manipulators. Bwodpfx Amjfz Dubo Rsn

Year of construction: 2025, condition: new, Curing ovens shown in the photos can vary in price depending on size, configuration, and optional features. 💡📏⚙️ At ROMER, we manufacture both standard models and fully bespoke solutions, tailored to your process requirements. 🏭✅ Tell us your part size, line capacity, curing profile, and available space - and we will propose the best setup and the options that actually improve daily performance. 🔥🎯 🧠📡 Control and monitoring Live process control for temperature, time, airflow, and modes - with alarms and saved recipes for repeatable cycles. 🔁✅ 🔥🧩 Heating module Fast heat-up and stable temperature thanks to efficient heating elements and quick energy transfer. ⚡🌡️ 🌀💨 Air circulation Uniform airflow reduces temperature differences for consistent coating quality. 🎯✅ 🧱❄️ Insulation and design Smart chamber construction minimizes heat loss - faster reaching setpoint, lower consumption. ♻️📉 🛡️⚠️ Safety and certification Sensors, interlocks, and protection logic increase safety and reliability. 🔒👷 ⚡💰 High efficiency Optimized heat transfer and reduced losses mean real operating savings. 📉🔥 ⏰🤖 Automatic start Programmable schedule - automatic preheating before the shift for smoother production starts. ⏱️✅ 🚪🔒 Self-latching doors + intelligent chimney Prevents accidental opening, chimney activates only when needed for safer operation. 🧯✅ 🌿🔋 ECO mode Low-energy standby when idle - fuel consumption reduction up to 20% (depending on process). 🌱📉 👀💡 View and lighting Inspection without opening the door - fewer temperature drops, easier supervision. ✨👁️ 🛤️🔥 Guide rails + automatic hood Heat hood runs only during loading to reduce temperature loss, automatic rail infeed improves ergonomics and loading speed. 🙌⚙️ 🎛️🌡️ MULTI-ZONE HEAT Independent zone control for uniform curing of parts with different mass and geometry. 🧩✅ 🧠♨️ MTS system Heating elements mounted without thermal bridges - higher efficiency and faster time to set temperature. ⚡⏱️ Bodoyg H Erjpfx Am Rjwn 2-in-1 🧱↔️🧱 Split chamber Movable partition for two independent zones - drying and curing in one unit for maximum flexibility. 🚀🔁 🎚️🌀 VFD ventilation Variable fan speed based on chamber conditions - better control and lower electricity use. ⚙️💡

Condition: new, Year of construction: 2026, 🏭 POWDER COATING BOOTH KPP Automatic filter cleaning with adjustable pulse timing, plus manual mode. 🧼⏱️🖲️ Bsdpfx Aofy T Tbsm Rswn 100% polyester filters - washable, water-resistant, long-lasting. 🧵💧♻️ ROMER JET™ filter cleaning - patented high-speed air pulse for powerful cleaning. 💥💨🏅 Low-noise aluminium fans (74-79 dB) - safer, spark-minimized operation with low power use. 🔇⚡🛡️ Adjustable airflow baffle - antistatic plate protects filters and improves extraction. 🌬️🛡️📈 Leak-tight filter mounting - gasket + clamp for strong sealing and easy service. 🔩🧷✅ Touchscreen control - auto (time), auto (clogging sensor), manual + filter change alerts. 📲🔁⚠️ Optional powder container - waste collection or fluidized tank with direct applicator feed. 🧺💨🎯 Overhead puller - moves beams through the booth, reducing manual effort. 🏗️➡️💪 Integrated sieving unit (with container) - clean recovered powder for reuse, EX-zone vibrator. 🧪♻️⚙️ Explosion-proof design - components selected to prevent explosive mixtures. 🛡️💥✅

Year of construction: 2020, condition: new, 7" Touchpad Large color touch panel looks aesthetically and uses comfortably and intuitively. Set on it all the important parameters.Memory 20 programs each with 10 events You can save up to 20 programs and activate up to 10 consecutive events time-temperature arranged in the heating curve. This is especially needed for the more demanding process.Information about consumption of power Consumption is calculated based on the settings of the burner. This feature will allow you to estimate the cost of the cycle, consumption and plan check staff.Recorder of cycle USB Each of the ovens is equipped with two-channel temperature recording on USB flash drive.. Each file is automatically created and is responsible for a separate cycle are recorded temperature extremes, hour and minute measurement. Files are saved in * .csv (Excel sheet) For all buyers the end of 2016 option is free, the competition for the option you have to pay up to several thousand euros. History 20 latest of burn Bodpfx Amjfz Apqo Rewn Something's wrong? and perhaps too few overbroad elements from the oven? Now you check thoroughly oldest and lastest burning parameters, how often took, whether cycle proceeds without any problems, what was the consumption and when they ran. Start the oven automatically at 6 am How many times have you stay after hours and expecting end of the cycle? If you own a powder coating plan that works for a long time, You know exactly what we are talking about. With our solution you can leave cycle not cured in the oven, to automatically end when you come to the job next morning.

Year of construction: 2020, condition: new, Touch control ROMER cabins are equipped with 4 "color touch displays. Operation of the cabin is intuitive, takes place in 3 modes, automatic (time), automatic (based on a clogged filter sensor), or manual Filter clogging sensor A sensor is installed in the cabins, which queues the filters for cleaning when they become clogged. The system also informs you when the filters have worn out Automatic filter cleaning The electronic system for automatic filter cleaning has a range of cleaning frequency and shot time adjustment. Each of the filters is cleaned separately, the filters can also be cleaned manually using the buttons. We know from experience that it is difficult for the operator to enforce filter cleaning. Thanks to this system, the operator will not have to think about it anymore. Low volume Bodpfx Amjfz A Ilj Rown Aluminum fans are very quiet, they work at the level of 74-79dB - It's not much. with the standard cabin structure, it's even hard to talk. Broaching machine through the cabin By dragging the suspension beams within the cabin, the cabin improves work efficiency, thus relieving the painter who no longer has to move them by hand. Explosion-proof design The booths are designed to prevent the formation of an explosive mixture during the painting process. Each of the components has been carefully selected to minimize this risk.

Year of construction: 2025, condition: new, Curing ovens shown in the photos can vary in price depending on size, configuration, and optional features. 💡📏⚙️ At ROMER, we manufacture both standard models and fully bespoke solutions, tailored to your process requirements. 🏭✅ Tell us your part size, line capacity, curing profile, and available space - and we will propose the best setup and the options that actually improve daily performance. 🔥🎯 🧠📡 Control and monitoring Live process control for temperature, time, airflow, and modes - with alarms and saved recipes for repeatable cycles. 🔁✅ 🔥🧩 Heating module Fast heat-up and stable temperature thanks to efficient heating elements and quick energy transfer. ⚡🌡️ 🌀💨 Air circulation Uniform airflow reduces temperature differences for consistent coating quality. 🎯✅ 🧱❄️ Insulation and design Smart chamber construction minimizes heat loss - faster reaching setpoint, lower consumption. ♻️📉 🛡️⚠️ Safety and certification Sensors, interlocks, and protection logic increase safety and reliability. 🔒👷 ⚡💰 High efficiency Optimized heat transfer and reduced losses mean real operating savings. 📉🔥 ⏰🤖 Automatic start Programmable schedule - automatic preheating before the shift for smoother production starts. ⏱️✅ Bwodpfx Amjfz U Nbo Rsn 🚪🔒 Self-latching doors + intelligent chimney Prevents accidental opening, chimney activates only when needed for safer operation. 🧯✅ 🌿🔋 ECO mode Low-energy standby when idle - fuel consumption reduction up to 20% (depending on process). 🌱📉 👀💡 View and lighting Inspection without opening the door - fewer temperature drops, easier supervision. ✨👁️ 🛤️🔥 Guide rails + automatic hood Heat hood runs only during loading to reduce temperature loss, automatic rail infeed improves ergonomics and loading speed. 🙌⚙️ 🎛️🌡️ MULTI-ZONE HEAT Independent zone control for uniform curing of parts with different mass and geometry. 🧩✅ 🧠♨️ MTS system Heating elements mounted without thermal bridges - higher efficiency and faster time to set temperature. ⚡⏱️ 2-in-1 🧱↔️🧱 Split chamber Movable partition for two independent zones - drying and curing in one unit for maximum flexibility. 🚀🔁 🎚️🌀 VFD ventilation Variable fan speed based on chamber conditions - better control and lower electricity use. ⚙️💡

Year of construction: 2020, condition: new, Touch control ROMER cabins are equipped with 4 "color touch displays. Operation of the cabin is intuitive, takes place in 3 modes, automatic (time), automatic (based on a clogged filter sensor), or manual Filter clogging sensor A sensor is installed in the cabins, which queues the filters for cleaning when they become clogged. The system also informs you when the filters have worn out Automatic filter cleaning The electronic system for automatic filter cleaning has a range of cleaning frequency and shot time adjustment. Each of the filters is cleaned separately, the filters can also be cleaned manually using the buttons. Bwsdsfzktzjpfx Am Rsn We know from experience that it is difficult for the operator to enforce filter cleaning. Thanks to this system, the operator will not have to think about it anymore. Low volume Aluminum fans are very quiet, they work at the level of 74-79dB - It's not much. with the standard cabin structure, it's even hard to talk. Broaching machine through the cabin By dragging the suspension beams within the cabin, the cabin improves work efficiency, thus relieving the painter who no longer has to move them by hand. Explosion-proof design The booths are designed to prevent the formation of an explosive mixture during the painting process. Each of the components has been carefully selected to minimize this risk.

Year of construction: 2020, condition: new, Transport systems Depending on the customer's requirements, transport systems can move on the floor or be suspended on poles. - For comfortable solutions for manual installations, we recommend suspended cross traverses (cross transport). Bwjdpefz Dt Nefx Am Rsn - For automated systems, chain conveyors are most often used that do not stop and are a great solution for companies that focus on quality and repeatability of the process. - For companies that make different items at once and have e.g. several cabins with different colors, flexible solutions with the use of the power-and-free conveyor are used. This is the most expensive solution. All installations are made to measure, depending on the customer's requirements. Continuous suspended chain transport systems are designed and manufactured to individual customer orders. In this system, it is also possible to make bottom conveyor systems on which details are placed, e.g. flower pots, rims (photo). ROMER also manufactures suspended transport systems. Crossbeams (cross transports) are designed and made for the needs of specific installations The use of one photocell The use of one photocell in the space of the detail allows you to measure its length and, consequently, gives the option of switching on the guns when the detail appears in their range, and switching off the guns immediately after painting the detail. The photocell is standard equipment. Identification of details by means of special markers. Above the sling there are plates with identification holes. Based on them, the PLC controller in conjunction with the photocell recognizes the painted detail, turns the guns on and off in good time - thus saving energy and powder paint. Vertical shape detection. The use of light gates with horizontal detectors allows the PLC controller to analyze the shape of a detail vertically. The PLC controller counts the time in which the detail should appear in the gun space - thanks to this it is possible to selectively turn the guns on or off. Using light gates with multiple sensors horizontally and vertically. This solution allows precise measurement of workpiece dimensions, thanks to which it is also possible to control manipulators.

Year of construction: 2020, condition: new, Transport systems Depending on the customer's requirements, transport systems can move on the floor or be suspended on poles. Bwedpsfz I D Djfx Am Rsn - For comfortable solutions for manual installations, we recommend suspended cross traverses (cross transport). - For automated systems, chain conveyors are most often used that do not stop and are a great solution for companies that focus on quality and repeatability of the process. - For companies that make different items at once and have e.g. several cabins with different colors, flexible solutions with the use of the power-and-free conveyor are used. This is the most expensive solution. All installations are made to measure, depending on the customer's requirements. Continuous suspended chain transport systems are designed and manufactured to individual customer orders. In this system, it is also possible to make bottom conveyor systems on which details are placed, e.g. flower pots, rims (photo). ROMER also manufactures suspended transport systems. Crossbeams (cross transports) are designed and made for the needs of specific installations The use of one photocell The use of one photocell in the space of the detail allows you to measure its length and, consequently, gives the option of switching on the guns when the detail appears in their range, and switching off the guns immediately after painting the detail. The photocell is standard equipment. Identification of details by means of special markers. Above the sling there are plates with identification holes. Based on them, the PLC controller in conjunction with the photocell recognizes the painted detail, turns the guns on and off in good time - thus saving energy and powder paint. Vertical shape detection. The use of light gates with horizontal detectors allows the PLC controller to analyze the shape of a detail vertically. The PLC controller counts the time in which the detail should appear in the gun space - thanks to this it is possible to selectively turn the guns on or off. Using light gates with multiple sensors horizontally and vertically. This solution allows precise measurement of workpiece dimensions, thanks to which it is also possible to control manipulators.

Year of construction: 2020, condition: new, Transport systems Depending on the customer's requirements, transport systems can move on the floor or be suspended on poles. - For comfortable solutions for manual installations, we recommend suspended cross traverses (cross transport). - For automated systems, chain conveyors are most often used that do not stop and are a great solution for companies that focus on quality and repeatability of the process. - For companies that make different items at once and have e.g. several cabins with different colors, flexible solutions with the use of the power-and-free conveyor are used. This is the most expensive solution. All installations are made to measure, depending on the customer's requirements. Continuous suspended chain transport systems are designed and manufactured to individual customer orders. In this system, it is also possible to make bottom conveyor systems on which details are placed, e.g. flower pots, rims (photo). ROMER also manufactures suspended transport systems. Crossbeams (cross transports) are designed and made for the needs of specific installations Bwsdpjfz I Edjfx Am Rjn The use of one photocell The use of one photocell in the space of the detail allows you to measure its length and, consequently, gives the option of switching on the guns when the detail appears in their range, and switching off the guns immediately after painting the detail. The photocell is standard equipment. Identification of details by means of special markers. Above the sling there are plates with identification holes. Based on them, the PLC controller in conjunction with the photocell recognizes the painted detail, turns the guns on and off in good time - thus saving energy and powder paint. Vertical shape detection. The use of light gates with horizontal detectors allows the PLC controller to analyze the shape of a detail vertically. The PLC controller counts the time in which the detail should appear in the gun space - thanks to this it is possible to selectively turn the guns on or off. Using light gates with multiple sensors horizontally and vertically. This solution allows precise measurement of workpiece dimensions, thanks to which it is also possible to control manipulators.

Year of construction: 2020, condition: new, Touch control ROMER cabins are equipped with 4 "color touch displays. Operation of the cabin is intuitive, takes place in 3 modes, automatic (time), automatic (based on a clogged filter sensor), or manual Filter clogging sensor A sensor is installed in the cabins, which queues the filters for cleaning when they become clogged. The system also informs you when the filters have worn out Automatic filter cleaning The electronic system for automatic filter cleaning has a range of cleaning frequency and shot time adjustment. Each of the filters is cleaned separately, the filters can also be cleaned manually using the buttons. We know from experience that it is difficult for the operator to enforce filter cleaning. Thanks to this system, the operator will not have to think about it anymore. Low volume Aluminum fans are very quiet, they work at the level of 74-79dB - It's not much. with the standard cabin structure, it's even hard to talk. Broaching machine through the cabin By dragging the suspension beams within the cabin, the cabin improves work efficiency, thus relieving the painter who no longer has to move them by hand. Explosion-proof design Bedpfxefz I Ehj Am Rown The booths are designed to prevent the formation of an explosive mixture during the painting process. Each of the components has been carefully selected to minimize this risk.