Used Moisture for sale (268)

Condition: new, Year of construction: 2024, machine/vehicle number: 6913390001, hoku 113-90 – Solid tradesman compressors with V-belt drive and 2-cylinder high-performance unit made of gray cast iron The universal one with V-belt drive and high-quality equipment, especially suitable for tradesmen, for use where quality of compressed air as well as durability and efficiency are essential, long service life thanks to high-performance units with low speed, safe transport and excellent stability thanks to large wheels with parking brake, optimal cooling thanks to large fan wheel, aftercooler with cooling fins ensures a low boiler inlet temperature and thus less moisture in the compressed air, better efficiency thanks to optimized units, standard Gjdpjvl Euxjfx Amuoit with Condor pressure switch, pressure gauge, pressure reducer with water separator and quick coupling, motor with overload protection Technical data: Suction capacity 500 l/min., filling capacity 375 l/min., maximum pressure 10 bar, tank capacity 90 l, cylinders/stages 2/1, speed 1,300 min-1, engine power 3 kW / 400 V from the Seevetal location, without transport, as seen, subject to prior sale.

Condition: new, machine/vehicle number: 691340002, hoku 119-90 – 2-stage compression mobile piston compressor The universal one with V-belt drive and high-quality equipment, especially suitable for tradesmen, for use where quality of compressed air as well as durability and efficiency are essential, long service life thanks to high-performance units with low speed, safe transport and excellent stability thanks to large wheels with parking brake, optimal cooling thanks to large fan wheel, aftercooler with cooling fins ensures a low boiler inlet temperature and thus less moisture in the compressed air, better efficiency thanks to optimized units, standard with Condor pressure switch, pressure gauge, pressure reducer with water separator and quick coupling, motor with overload protection Gedpfx Asvl Ev Aemujit Technical data: Suction capacity 674 l/min., filling capacity 505 l/min., maximum pressure 10 bar, tank capacity 90 l, cylinders/stages 2/2, speed 920 min-1 , Engine power 4 kW / 400 V from the Seevetal location, without transport, as seen, subject to prior sale.

Condition: used, container length: 20 ft, -Used -Wind and waterproof -available immediately -The price is ex depot Frankfurt (also available in other regions on request) -We are happy to take care of delivery and crane unloading (costs on request) Our 20-foot storage container is the perfect solution for your storage needs. It offers you a safe, flexible and cost-effective way to store your goods and materials. Whether for use on construction sites, in industry or for private purposes - this container meets the highest standards of quality and functionality. Product features: - Dimensions: 20 feet (6.06 m) long, 2.44 m wide and 2.59 m high - Volume: Approx. 33 m³, ideal for storing large quantities of goods - Material: Robust steel construction that guarantees durability and resistance - Security: Equipped with a reliable locking system and reinforced doors to optimally protect your stored goods - Weatherproof: Weatherproof and corrosion-resistant coating that protects your goods from rain, sun and other environmental influences - Ventilation: Strategically placed ventilation openings prevent the accumulation of moisture and ensure an optimal storage climate Applications: The 20 foot storage container is ideal for storing tools, machines, materials, furniture and much more. It can be used both temporarily and permanently and is ideal for construction sites, warehouses, events or as additional storage space for your company. Gijdevyactspfx Amuot Additional benefits: - Easy handling: Thanks to the standardized dimensions, the container is easy to transport and place. - Flexibility: The container can be used in different locations and is mobile, so you can move it if necessary. Customization: On request, we offer individual modifications to meet specific requirements, such as shelving systems or additional ventilation. Rely on our new 20-foot storage container for safe and efficient storage of your goods!

Year of construction: 2013, condition: used, Drying chamber with false ceiling ventilation and frontal trolley loadingfor the production and conditioning of 3 mm oak lamellas, at initial moisture 12 tomax. 15 % / final humidity 7 %used, good conditionmake Mühlböcktype ZSWM2110-1180C - 1.0 l/h at 40° C over 30 % HFyear of construction 2013rated power 7 kW/15Afrequency 50 Hzcontrol voltage 24VDC/230VACprotection class IP54content:the chamber holds- 2 packages in width a 1.10 m - with 0.20 m space between each package- 1 package in height a 1.80 m - with 0.10 m thick underlays and a 0.10 m high free space- 2 packages in length a 2.20 m - plus 0.60 m free spaceThe chamber contains 4 stacking packages and has a total gross volume of 17.4 m²The chamber has a net capacity of 4 m³ of timber - with a timber thickness of 3 mm and a stacking strip thickness of 10 mmand 90 % width utilization with edged ble dimensions of each chamber: Width 2.40 m x height 2.30 m x length 5.00 m- aluminum cassette construction- aluminum frame- dimensionally stable rock wool insulation- aluminum trapezoidal sheet- snow load 100 kg/m²- 2-leaf hinged door- front loading- 2 fans a 3 kW (D=800 mm)- stainless steel/aluminum finned tube heating coil with 50 kW, flow temperature of 80 °C, return temperature 73°C- servo-controlled supply and exhaust air flaps- cold water spraying- chambers work fully automatically- computer control K5Disassembly: Customer locationhandover as viewedwithout guarantee and warranty Godpfx Amjvwfhijueit

Condition: reconditioned (used), Year of construction: 2003, functionality: fully functional, briquette diameter: 60 mm, Refurbished machine suitable for smaller, single-shift carpentry operations. It offers a robust construction while providing solid performance. Maximum briquette output: 70 kg/h. Year of manufacture: 2003. In very good and well-maintained condition. Original warranty and post-warranty service available directly from our company. Professional PRODECO hydraulic briquetting presses are ideal for small and medium-sized woodworking operations. They enable efficient processing of waste into environmentally clean, high-calorific fuel without the need for binders. These machines are characterized by compact space requirements, low energy consumption, and easy operation. Technical specifications: - Motor power: 5.5 kW - Briquette output: 35 to 70 kg/h (depending on material) - Briquette diameter: 60 mm Gedpfx Asvva Rpemusit - Briquette stroke length up to 60 mm (so-called endless briquette) - Hopper diameter: 1000 mm - Weight: 650 kg - Machine dimensions: 1170 x 1700 x 1510 mm Features: - Hydraulic unit with 7 pressing cycles/min - Dual manometer for improved pressure monitoring - Level sensor for the height of briquetted material - Oil level sensor - Inspection window - CE safety standard compliant - Moisture content of processed material must not exceed 18% The machine is refurbished, calibrated, and tested.

Condition: used, Year of construction: 2021, Number of spindles 5 St. Working width 250 mm Working height 160 mm Length of the planing table 2500 mm Feed motor 4 kW Feed speed 6-24 m/min. control K2 Basic 7"-Touch KUPER SWT XL-5 AUTOMATIC PLANER AND MOULDER ----- LIKE NEW, showroom machine ! - 5 spindles: bottom, right, left, top, bottom - Speed: frequency-controlled 4,000 - 6,000 rpm, spindle 4.5 to 8,000 rpm - Width and height motor-controlled: left spindle radial upper spindle axial - Feed carrier motor-controlled - Additional motor-controlled positioning: right spindle radial and axial left spindle axial - working width 250 mm TECHNICAL DATA ----- Working width (perimeter of tools 163 mm) 15 - 230 mm Working height(perimeter of tools 163 mm) 10 - 150 mm (perimeter of tools 123 mm) 10 - 160 mm Min. workpiece length: single piece: min. 800 mm piece by piece: min. 300 mm The processing of the work pieces is depending on the following operating parameters: material, wood moisture, tools, diameter of the chip removal and feed speed. If necessary adjustments to the operating parameter have to be done. SPINDLE CONFIGURATION ----- bottom, right, left, top, bottom 1st spindle: HORIZONTAL, BOTTOM ----- Siemens IE3 motor with inverter brake 5,5 kW (7,5 HP) Diameter 40 mm Spindle length 250 mm Usabale length for tools Spindle length minus approx. 6 mm Drive, frequency-controlled 4000 - 6000 rpm Perimeter of tools 125 - 160 mm Reference cutter Diameter difference 20 - 25mm to the cutterhead Connecting piece D = 125 mm Quick action lock nut Pro-Lock 2nd spindle: VERTICAL, RIGHT ----- Siemens IE3 motor with inverter brake 5,5 kW (7,5 HP) Diameter 40 mm Spindle length 165 mm Usable length for tools spindle length minus approx. 6 mm Drive, frequency-controlled 4000 - 6000 rpm Perimeter of tools 112 - 200 mm Adjustment path axial 60 mm Adjustable table plate to tool radius Standard profile depth 20 mm Connecting piece D = 125 mm Aspiration individual adjustable shavings guiding plate Quick action lock nut Pro-Lock 3rd spindle: VERTICAL, LEFT ----- Siemens IE3 motor with inverter brake 7,5 kW (10 HP) Diameter 40 mm Spindle length 165 mm Usable length for tools spindle length minus approx. 6 mm Drive, frequency-controlled 4000 - 6000 rpm Perimeter of tools 112 - 200 mm Adjustment path axial 60 mm Standard profile depth 20 mm Adjustable table plate to tool radius Connecting piece D = 125 mm Aspiration individual adjustable shavings guiding plate Quick action lock nut Pro-Lock 4th spindle: HORIZONTAL, TOP ----- Siemens IE3 motor with inverter brake 7,5 kW (10 HP) Diameter 40 mm Spindle length 235 mm Usable length for tools spindle length minus approx. 6 mm Drive, frequency-controlled 4000 - 6000 rpm Perimeter of tools 112 - 200 mm Pressure shoe pneumatically, via linear guides dynamically adjustable Standard profile depth 20 mm Connecting piece D = 125 mm Aspiration individual adjustable shavings guiding plate Quick action lock nut Pro-Lock 5th spindle: HORIZONTAL, BOTTOM ----- Siemens IE3 motor with inverter brake 5,5 kW (7,5 HP) Diameter 40 mm Spindle length 235 mm Usable length for tools spindle lenght minus Gjdpfx Ajwgwmnjmuoit approx. 6 mm Drive, frequency-controlled...

Condition: used, Year of construction: 2021, Number of spindles 5 St. Working width 230 mm Working height 160 mm Length of the planing table 2500 mm Feed motor 4 kW Feed speed 6-24 m/min. Control K2 Basic 7"-Touch KUPER SWT XL-5 AUTOMATIC PLANER AND MOULDER ----- LIKE NEW, showroom machine ! - 5 spindles: bottom, right, left, top, bottom - Speed: frequency-controlled 4,000 - 6,000 rpm - Width and height motor-controlled: left spindle radial upper spindle axial - Feed carriage motorized adjustment TECHNICAL DATA in Detail ----- Working width (for tool diameter 125-163 mm): 15-230 mm Working height (for tool diameter 125 mm): 10-160 mm (Tool diameter up to 163 mm): 10-160 mm Min. workpiece length: single piece: min. 800 mm piece by piece: min. 300 mm The processing of the work pieces is depending on the following operating parameters: material, wood moisture, tools, diameter of the chip removal and feed speed. If necessary adjustments to the operating parameter have to be done. SPINDLE CONFIGURATION ----- bottom, right, left, top, bottom 1st spindle: HORIZONTAL, BOTTOM ----- Siemens IE3 motor with inverter brake 5,5 kW (7,5 HP) Diameter 40 mm Spindle length 250 mm Usabale length for tools Spindle length minus Gedpfowgwmhox Amusit approx. 6 mm Drive, frequency-controlled 4000 - 6000 rpm Perimeter of tools 125 - 160 mm Reference cutter Diameter difference 20 - 25mm to the cutterhead Connecting piece D = 125 mm Quick action lock nut Pro-Lock 2nd spindle: VERTICAL, RIGHT ----- Siemens IE3 motor with inverter brake 5,5 kW (7,5 HP) Diameter 40 mm Spindle length 165 mm Usable length for tools spindle length minus approx. 6 mm Drive, frequency-controlled 4000 - 6000 rpm Perimeter of tools 112 - 200 mm Adjustment path axial 60 mm Adjustable table plate to tool radius Standard profile depth 20 mm Connecting piece D = 125 mm Aspiration individual adjustable shavings guiding plate Quick action lock nut Pro-Lock 3rd spindle: VERTICAL, LEFT ----- Siemens IE3 motor with inverter brake 7,5 kW (10 HP) Diameter 40 mm Spindle length 165 mm Usable length for tools spindle length minus approx. 6 mm Drive, frequency-controlled 4000 - 6000 rpm Perimeter of tools 112 - 200 mm Adjustment path axial 60 mm Standard profile depth 20 mm Adjustable table plate to tool radius Connecting piece D = 125 mm Aspiration individual adjustable shavings guiding plate Quick action lock nut Pro-Lock 4th spindle: HORIZONTAL, TOP ----- Siemens IE3 motor with inverter brake 7,5 kW (10 HP) Diameter 40 mm Spindle length 235 mm Usable length for tools spindle length minus approx. 6 mm Drive, frequency-controlled 4000 - 6000 rpm Perimeter of tools 112 - 200 mm Pressure shoe pneumatically, via linear guides dynamically adjustable Standard profile depth 20 mm Connecting piece D = 125 mm Aspiration individual adjustable shavings guiding plate Quick action lock nut Pro-Lock 5th spindle: HORIZONTAL, BOTTOM ----- Siemens IE3 motor with inverter brake 5,5 kW (7,5 HP) Diameter 40 mm Spindle length 235 mm Usable length for tools spindle lenght minus approx. 6 mm Drive, frequency-controlled 4000 - 6000 rpm Perimeter of tools 112 - 200 mm Adjustment range axial 20 mm Connecting piece D = 125 mm Aspiration individ...

Condition: like new (used), Year of construction: 2014, briquette diameter: 150 mm, overall weight: 3,000 kg, power: 30 kW (40.79 HP), Capacity: 450-500 kg/h Max. pressure force: 1700kg/cm2 Batch moisture content: 15% Length: 1800 mm Width: 1800 mm Height: 1900 mm Transport height: 2200 mm Weight: 3000 kg Godpfx Aeqd Uy Ajmuoit Total power: 33 kW

Condition: new, Year of construction: 2024, WTG piercing bag sander and planer knife grinding machine Description: For an accurate and efficient work perfectly honed, razor-sharp cutting edge is an absolute must . With our grinder to sharpen your tools quickly , easily, accurately and inexpensively grind wood chisel (holly bag) , planer knives , chisels , chisel Advantages Very precise , stable and durable design Fast, in just 30 seconds you grind a perfect gratlose Just cut Extremely to use, even for apprentices and unskilled dry grinding principle, ie no problems with moisture ( water / oil) Infinitely variable cutting angle setting, you buy fewer new tools , resulting in lower maintenance and fixed costs. Gsdebxudkjpfx Amueit Made in SWITZERLAND = Swiss Quality Where the WTG is used : Wherever conventional wood is processed. For example, in carpentry , joinery , carpentry , schools, trade schools , training centers / training workshops. Structure of the grinding machine : The WTS is driven by a powerful 500 watt motor . When trolley is a dust-proof , high-precision ball bearings and profile rail guide as it is a thousand times used in machine tools , industrial robots and precision special machines. The stepless grinding service is realized by a precise and self-locking dovetail guide. The tool clamping is safe and stable over a parallel clamping system. Our WTG grinder has a unique price -performance ratio. See for yourself , or let us advise you . Specifications: Weight: 19 kg , weight : approx 55 x 35 x 30 cm , Connection: 230 V / connector type J , Motor: 500 watts , speed : 3000 r / min. Sandable tool width : 5-60 mm Cutting angle adjustment : 25 - 30 degrees continuously Main grinding wheel : Special fused alumina ø 100 mm polishing wheel / buffing wheel : special-type ROTAX ø 150 mm Other polishing and grinding wheels on request. Price EUR 2'100 .00 Shipping costs The company BERGER technology GmbH is worldwide for decades one of the leading manufacturers of high quality drill and tool grinding machines, multi spindle drill heads as well . Contact: Mr. Marc Broennimann

Condition: new, Year of construction: 2025, Sharpening woodworking tools The PROFI chisel (lancing bag) and planing knife grinding machine! No cheap ASIA copy! The original! WOOD-TOOL-GRINDER WTG-1 - «Swiss Currently the absolute cheapest PROFI wood tool grinder on the market! For a precise and efficient work, a perfectly ground, razor-sharp cutting edge is a must. With our grinder sharpen your tools like: «Chisels, plow blades, chisels, chisels» fast, simple, accurate and inexpensive ... Made in Switzerland = Swiss Quality Where is the WOOD-TOOL-GRINDER «WTG-1» used? - Where conventionally wood is processed. - For example, in carpentry, carpentry, - carpentry, schools, trade schools, - Training centers / training workshops ... Your advantages - Very precise, stable and stable construction - Fast, in just 30 seconds you grind a perfect flashless edge - Extremely easy to use, also for apprentices and unskilled workers - Dry grinding principle, i. no problems with moisture (water / oil) - Stepless cutting angle adjustment - You buy fewer new tools, thus lower maintenance and fixed costs Construction of the wooden tool grinding machine «WTG-1» The WTG is powered by a powerful 500 watt motor. The carriage used is a dust-proof, high-precision, ball-bearing profiled rail guide, which is used a thousand times in machine tools, industrial robots and precision special purpose machines. Stepless grinding is achieved by means of an accurate and self-locking dovetail. The tool clamping is safe and stable via a parallel clamping system. Giodpjdt Ap Aofx Amuot Technical specifications Weight: 20 kg Connection: 230 volts Motor: 500 watts Speed: 3000 rpm Grindable tool width: 5 - 60 mm Cutting angle adjustment: 25 - 30 ° degrees stepless Main grinding wheel: special corundum Ø 100 mm Polishing wheel / buffing wheel: special type ROTAX Ø 150 mm I would recommend you the basic machine and the grinding double set. So you are well prepared. Your direct contact person: Sir Marc Brönnimann Head of Sales & Assembly BST Kaindl, DAREX, HARICH, Vertex, Drill Doctor, METEOR, Optima, Tatar, Promac, Cuoghi, Avyac, Christen, MOTOM, VITAX, WASU, Ulrich Klingel, ISELI, Schneeberger, Lamallo,

Condition: used, Year of construction: 2012, type of input current: three-phase, filter area: 62 m², suction capacity: 2,500 m³/h, negative pressure: 9,000 Pa, Dust extractor, welding fume extractor, self-cleaning pneumatic filter, vacuum dust collector, absorber for plasma, laser, sandblasting, and all types of dry dust. The filter is pneumatically cleaned with compressed air pulses during operation, resulting in high device efficiency. Large filtration area requiring minimal space. Gedpfx Amoxrpmzeujit High mechanical stability of the filter material ensures long service life. Compared to conventional rigid filters, it causes minimal pressure loss. Short bursts of compressed air during the filtration process provide effective filter cleaning. Fan power: 7.5 kW Capacity: 2,500 m³/h at a pressure of up to 9,000 Pa Filter cartridges: 11 pcs Filtration surface: 62 m² The device is equipped with an automatic system for impregnating cartridge filters. The extractor is designed for special applications where the filtered fumes and dust may be moist and sticky. Adding impregnating agent captures moisture from the fume, protecting the filters from clogging. In this case, the lifespan of the cartridge filters is increased. Stock number: 0981

Condition: new, Year of construction: 2025, Bending machine PROD-MASZ to the plate ZGR 2640.-0.8 is a sensational machine for precision bending of all types of metal sheets Godsc Nwd Aspfx Amueit (steel 0.8mm, titanium zinc 0.8mm, aluminum of 1.2 mm, copper sheet 0.65 mm). Equipped with a rack supporting plate, two front bumpers, bending angle measurement, a single lock of bending angle, turnbuckles, eccentric mechanisms. Each part of the machine is adjustable, which allows for adjustment of the arc bending. Used in the device locking system (set by the operator) allows you to achieve the desired angle of bending. Table rear and front bumpers are made of galvanized racks. Ideal for all kinds of steel treatments - wherever the roof is exposed to moisture infiltration. Proper execution of these connections certainly prolong the life of the roof. By hers construction she can be used not only for bending panels with both the ferrous metal, sheets of plastic and fiberboard.

Condition: new, Year of construction: 2025, total height: 4,000 mm, total length: 7,000 mm, total width: 3,000 mm, warranty duration: 24 months, temperature: 80 °C, air demand: 36,000 m³/h, input voltage: 380 V, heating capacity: 345 kW (469.07 HP), power: 40 kW (54.38 HP), fuel: liquid petroleum gas (LPG), energy consumption: 40 kWh, insulation material: Mineralwolle, insulation thickness: 50 mm, nominal power: 345 kW (469.07 HP), Equipment: lighting, MAIN STANDARD Our paint booths are designed to meet all necessary requirements for paint application, including air filtration, extraction, lighting, and a controlled environment. Booth processes are managed via a PLC system, ensuring that desired values are maintained consistently. OPERATING PRINCIPLES OF THE BOOTH The booth’s processes are managed through a control panel, which oversees the following steps: PAINTING PROCESS During painting, 100% fresh air is drawn in from outside and passed through front filters before entering the distribution chamber at ambient temperature. The air is then expelled through the extraction unit. Floor filters (paint stop filters) collect paint particles, and the air passes through final exhaust filters before being discharged. FLASH-OFF PROCESS After painting, the booth continues operating for approximately 15 minutes to purge residual solvents and thinners. During this phase, fresh air circulates from outside into the booth. DRYING PROCESS In this stage, 80% of the air passing through the booth is heated to 60°C and introduced via a distribution system. Since 20% of the solvent is released during drying, it is expelled with the exhaust air. Industrial coatings are typically dried at 60°C, but the booth temperature can be adjusted as needed via the control panel. Gijdpfx Aswzmcbomuet COOLING PROCESS After the 30-minute drying cycle, the coil is deactivated via the control panel, the pneumatic damper closes, and the extraction system restarts. During the subsequent 5-minute cooling phase, fresh air from outside circulates through the booth, after which the system shuts down automatically. ELECTRICAL AND ELECTRONIC EQUIPMENT These control panels govern the functions and operation of machines and devices housed within the booth. The panel is made of durable galvanized sheet and steel profiles and is fully enclosed to protect against dust and moisture. Electrical Equipment and Control Panel: • The control panel contains essential components such as circuit breakers, fuses, indicator lamps, thermal relays, contactors, and connectors. • Heat-resistant cables are used for command and control connections between the control panel and motors or other electrical devices. • Electrical wiring is designed to accommodate booth relocation if needed. • Operating equipment uses 380 V 50 Hz, while control devices operate at 220 V. • The booth’s operation time can be monitored on the electronic control panel, enabling straightforward maintenance scheduling. • Temperature and time settings for booth ventilation (solvent flash-off), intermediate drying, and final drying can be easily adjusted to required values on the digital display of the electronic control panel. • Users can monitor and adjust the drying time using the heating thermostat and time relay.

Condition: new, Year of construction: 2025, functionality: fully functional, total height: 5,600 mm, total length: 11,200 mm, total width: 5,100 mm, type of input current: three-phase, warranty duration: 24 months, inner dimension height: 4,970 mm, inner dimension length: 11,000 mm, temperature: 80 °C, inner dimension width: 5,000 mm, air demand: 52,000 m³/h, input voltage: 380 V, heating capacity: 250 kW (339.91 HP), power: 45 kW (61.18 HP), fuel: liquid petroleum gas (LPG), input frequency: 50 Hz, energy consumption: 45 kWh, insulation thickness: 50 mm, nominal power: 250 kW (339.91 HP), sheet thickness steel (max.): 2 mm, Equipment: lighting, * Air Preparation Unit: The air preparation unit is a recirculation system that supplies the cabin with filtered fresh air and exhausts used air during the painting process. It heats the air to 60 °C, mixes the used air with 10% fresh air via an automatic multi-damper system, and reheats the air before routing it back into the cabin. The air is heated using a burner and a heat exchanger, both made of high-quality 304 stainless steel and housed within the fresh air unit. During painting, the air is filtered twice (via front and ceiling filters) before it enters the cabin. The contaminated air is also filtered twice (through inlet and outlet filters) before it exits via the exhaust unit. Air preparation units are insulated like the side walls to minimize heat loss and are protected against potential vibration and noise thanks to rubber seals on the covers. The exhaust air is regulated by a damper in the outlet duct, which helps control the internal pressure of the cabin. * PRINCIPLES OF CABIN OPERATION: The processes in the cabin are controlled via a control panel that manages the following steps: * PAINTING PROCESS: During painting, 100% fresh air is drawn in from outside and passed through front filters before entering the distribution chamber at ambient temperature. The air is then expelled by the extraction unit. Floor filters (paint stops) capture paint particles, and the air passes through the final exhaust filters before being discharged. * FLASH-OFF PROCESS: After painting, the cabin operates for approximately 15 more minutes to purge residual solvents and thinners. During this phase, fresh air from outside continues to circulate in the cabin. * DRYING PROCESS: In this phase, 80% of the air passing through the cabin is heated to 60 °C and supplied to the cabin via a distributor. As 20% of the solvent is released during drying, these solvents are expelled with the exhaust air. Industrial coatings are typically dried at 60 °C, but the cabin temperature can be adjusted via the control panel as required. * COOLING PROCESS: After the 30-minute drying process, the coil is deactivated via the control panel, the pneumatic damper closes, and the extraction system restarts. During the 5-minute cooling phase, fresh air from outside circulates in the cabin, after which the system stops automatically. Gjdpjwzl Hxefx Amujit ELECTRICAL AND ELECTRONIC EQUIPMENT: These control panels manage the functions and operation of all machinery and devices inside the cabin. The control panel is constructed from durable galvanized sheet metal and steel profiles and is fully enclosed to protect against dust and moisture. Electrical devices and control panels: • The control panel contains essential components such as circuit breakers, fuses, indicator lamps, thermal relays, contactors, and connectors. • Heat-resistant cables are used for command and control lines between the panel and motors or other electrical devices. • Electrical wiring is designed to allow for cabin relocation if necessary. • Operating devices use 380 V 50 Hz, while control devices use 220 V.

Condition: used, -Used -Wind and waterproof -available immediately -The price is from the Kornwestheim depot (also available in other regions on request) -We are happy to take care of delivery and crane unloading (costs on request) Our 20-foot storage container is the perfect solution for your storage needs. It offers you a safe, flexible and cost-effective way to store your goods and materials. Whether for use on construction sites, in industry or for private purposes - this container meets the highest standards of quality and functionality. Product features: - Dimensions: 20 feet (6.06 m) long, 2.44 m wide and 2.59 m high - Volume: Approx. 33 m³, ideal for storing large quantities of goods - Material: Robust steel construction that guarantees durability and resistance - Security: Equipped with a reliable locking system and reinforced doors to optimally protect your stored goods - Weatherproof: Weatherproof and corrosion-resistant coating that protects your goods from rain, sun and other environmental influences - Ventilation: Strategically placed ventilation openings prevent the accumulation of moisture and ensure an optimal storage climate Applications: The 20 foot storage container is ideal for storing tools, machines, materials, furniture and much more. It can be used both temporarily and permanently and is ideal for construction sites, warehouses, events or as additional storage space for your company. Additional benefits: - Easy handling: Thanks to the standardized dimensions, the container is easy to transport and place. - Flexibility: The container can be used in different locations and is mobile, so you can move it if necessary. Giodpfx Aevyab Asmujt Customization: On request, we offer individual modifications to meet specific requirements, such as shelving systems or additional ventilation. Rely on our new 20-foot storage container for safe and efficient storage of your goods!

Condition: used, Year of construction: 2009, THIMON Automatic Pallet Hooder LIGNE CPHP 2000 Manufacturer Thimon – Savoie Hexapole, Rue Louis Armand, BP 69, 73420 Méry, France Type Industrial automatic pallet hooder (film hood application with roll unwind) Industrial Applications Automatic hooding of pallet loads at end-of-line to stabilize, protect, and secure pallets before shipping. Used on production and logistics lines in food, beverage, chemicals, cosmetics, and FMCG industries. Main Technical Specifications - Type: LIGNE CPHP 2000 - Year of manufacture: 2009 - Registration / ID: 507304 - Compliance: CE Machine Usage Giedpfjx N Utqjx Amust The LIGNE CPHP 2000 automates the application of a film hood over a full pallet load. The pallet is conveyed into the hooding area, the hood is formed and applied around the load to ensure pallet stability, protection against dust and moisture, and consistent handling and transport performance. Features / Differentiators - Large-format film roll unwind system suited for industrial throughput and high-volume pallet loads - End-of-line integration with pallet conveying and guarded safety area - Clear traceability for service and spare parts through ID 507304 and type LIGNE CPHP 2000

Condition: new, functionality: fully functional, machine/vehicle number: 102164, screw diameter: 20 mm, Brand new injection unit for ARBURG machines – fully equipped and ready for immediate use For sale is a completely new injection unit for ARBURG machines, comprising: Gisdpfxswlcf Hs Amust Cylinder with check valve Heating bands Nozzle Screw The unit was originally purchased as a spare cylinder for cleanroom production and was stored exclusively in a cleanroom warehouse. To protect against possible moisture it was permanently wrapped in oil paper and never used. Condition: unused, as new Storage: cleanroom, protected in original packaging Application: ideal as an immediately available replacement or exchange unit Perfect for anyone who needs a high-quality injection unit quickly and without lead times. Please feel free to contact me if you have any questions or are interested! I purchase all machines and peripheral equipment directly from customers at a fair price. The subsequent selling price is calculated reasonably so that all three parties – seller, buyer, and I as the intermediary – can conclude a fair transaction. Unscrupulous offers from various used machinery dealers are therefore not welcome.

Condition: new, Year of construction: 2025, functionality: fully functional, machine/vehicle number: HaRo2020, total width: 800 mm, total height: 1,100 mm, total length: 1,200 mm, briquette diameter: 60 mm, overall weight: 300 kg, warranty duration: 12 months, type of input current: AC, input voltage: 400 V, power: 3 kW (4.08 HP), Equipment: emergency stop, Our new HaRo2020 briquetting press, with a capacity of up to 40 kg/h, automatic tongs, and pre-compactor, is manufactured by ourselves. You can only purchase this machine directly from us, as we do not use intermediaries. The briquetting presses are CE-compliant and manufactured according to the latest standards. Since we produce most of the components in-house, we can offer the machine at a particularly competitive price. Price is exclusive of VAT. The new hydraulic unit is equipped with a SILENCE-PUMP, making the machine extremely quiet in operation. Another benefit of the helical gearing in the pump is increased durability. Everything is made in Germany! You are welcome to visit us and test the machine with your own material. When purchasing our briquetting press, you will receive a detailed and comprehensive German (PDF) operating manual for this machine. The input material must have a moisture content below 15%—ideally 10 to 12%—for sawdust and planer shavings. Technical Data – Hydraulic unit: 3.0 kW (connected load) – Power consumption per hour: approx. 1.8–2.0 kWh – Throughput: approx. 15–40 kg/h – Voltage: 400 V – Frequency: 50 Hz – Circuit protection: 16 A plug – Power cable length: 3 m – Hydraulic control with Bosch Rexroth valves – Briquette diameter: 60 mm (length varies according to material) Gijdpfxow A Hvdo Amujt – Motor equipped with motor protection switch and emergency stop—for operator and machine safety, including motor protection – No electronic components prone to failure such as controllers, sensors, or complicated electronics – Pressing without additives – Counter-pressure adapts fully automatically to your material – Thanks to the pre-compactor, bulky shavings are no problem – No adjustments or monitoring of the pressure required – Fully automatic operation Spare parts supply is guaranteed, as we manufacture the machines in small series in our facility in Germany. The large oil tank ensures that the oil will not overheat during continuous operation. Machine dimensions: Length: 1.25 m Width: 0.82 m Height: 1.11 m Feed hopper: Diameter approx. 80 cm x height 60 cm Weight: 300 kg The briquetting press is immediately operational and does not require installation—just plug it in and start working. The machine can be viewed and tested on-site. You are welcome to send us a sample of your material for testing; we find this is the most effective method.

Condition: good (used), Year of construction: 2007, functionality: fully functional, power: 7.63 kW (10.37 HP), total width: 2,300 mm, total length: 4,000 mm, total height: 3,000 mm, type of input current: three-phase, pressure: 6 bar, input voltage: 400 V, nominal heat output: 950 kW (1,291.64 HP), operating pressure: 6 bar, Equipment: hot water, type plate available, The Pyrtec boiler system is an underfeed stoker combustion unit with internal grate and burnout grate for universal application, and is suitable for a particularly wide fuel spectrum, ranging from dry wood waste to wet forest wood chips. Maximum water content w= 50%, corresponding to a wood moisture u of 100%. The complete boiler system is type-approved (Approval No.: 02-221-512) with continuous quality control by TÜV and consists of the following components: FEED AUGER WITH BACK-BURN BARRIER LAYER: The feed auger transports the fuel into the combustion chamber and the grate area of the fireblock. The robust auger flights are made from heat-resistant chromium steel in the combustion chamber area. The feed tube is equipped with mounts for the back-burn thermostat and the thermal extinguishing valve. Above the auger is a dosing container with a photoelectric sensor for level control of the fuel barrier layer required by TRD 414. The drive is provided by a maintenance-free helical gear motor and chain drive enclosed in a dust-tight chain guard. Accessoires: Extinguishing valve with dirt strainer COMBUSTION BLOCK: Solid combustion block with multiple layers of insulation and high-quality chamotte lining. The feed and grate area consists of the fire chamber, gasification grate, and descending burnout grate. All of these components are made of highly heat-resistant cast steel (Material No. 1.4868), at least 12 mm thick and individually replaceable. This type of primary combustion system has proven to be extremely effective even with challenging fuels (wet sawmill residues, high bark content, etc.). Ash and foreign substances falling through the grates can easily be removed from outside through access holes sealed with covers. The horizontal combustion chamber is optimally shaped for complete burnout and also provides a large ash compartment. The combustion chamber door is heavy-duty, well-insulated, and can be ideally swung aside on a robust double-joint hinge for maintenance purposes. BOILER: Horizontal hot water boiler in three-pass design, mounted on the fireblock, insulated and stylishly clad. The insulated boiler front door is designed to allow the installation of an oil or gas burner. Operating temperature: max. 120 °C Giedpfx Ajxwhw Asmuet Operating pressure: 3.0 bar Test pressure: 6.0 bar FLUE GAS DUST COLLECTOR PYRTEC-140 to PYRTEC-650: Constructed in axial cyclone design, fully insulated and mounted to the boiler. Equipped with two insulated cleaning covers, an ash container with quick-release fastener, and mounting flange for the flue gas fan. FLUE GAS DUST COLLECTOR PYRTEC-1000: Constructed in axial cyclone design, fully insulated, free-standing for optimal placement. Includes two insulated cleaning covers, mounting flange for the flue gas fan, and connection for the ash container. FLUE GAS FAN: Specially designed fan for wood combustion operation, very quiet, with a heavy-duty, heat-resistant motor and flexible heat-dissipating hub. The fan housing can be continuously rotated at the intake, with a round exhaust outlet.

Condition: new, functionality: fully functional, Year of construction: 2025, working width: 1,380 mm, overall weight: 80 kg, empty load weight: 80 kg, operation weight: 80 kg, High-quality wall-mounted (gable) fans with dimensions of 1380 x 1380 x 450 mm and a capacity of 44,500 m³. Motor power: 1.1 kW, 3-phase. This exhaust fan is suitable for industrial or agricultural applications and is often used in pig farms, poultry houses, greenhouses, or production halls. Gsdsxuvatspfx Amueit • The unit provides effective ventilation by removing stale air, excess moisture, and unpleasant odors. • It is a push-pull fan, operating in both exhaust and intake modes. • The galvanized sheet metal and protective mesh construction ensure durability and safe operation. • The large blade diameter and powerful motor enable high airflow efficiency.

Condition: excellent (used), Year of construction: 2011, operating hours: 216 h, functionality: fully functional, machine/vehicle number: 20MS090000/007, total length: 3,000 mm, type of input current: AC, total width: 2,500 mm, total height: 1,900 mm, overall weight: 1,450 kg, empty load weight: 1,450 kg, working width: 900 mm, compressed air connection: 6 bar, throughput speed: 50 mm/s, Gluing and longitudinal splicing machine For 0.4 to 3 mm thickness with direct gluing. With pre-gluing of edges up to 5 mm. Machine used very little, available ex location. Features: - Separate electric motors for chain and glue application - Glue is applied to the edge of the newly inserted veneer strip, increasing the strength of the glued joint - Robust, durable stainless steel conveyor chain with weighing joints - Separate temperature, speed, and pressure adjustment - Quick and easily accessible glue reservoir for fast and simple refilling or cleaning - Multiple heating zones for individual temperature adjustment - Extended service life of glue reservoir due to integrated cooling unit - Infinitely variable feed speed INCLUDES GLUE COOLER Technical specifications: Throat depth: 900 mm Minimum veneer strip width: 45 mm Minimum veneer strip length: 300 mm Veneer strip thickness: 0.4 – 3.0 mm (up to 5 mm) Veneer moisture content: max. 8 – 12 % Working height: 900 mm Feed speed: 5 – 50 m/min Heating section length: 1000 mm Maximum heating temperature: 250°C Giedjw E Rfbepfx Amujt Electrical connection: 9.0 kW, 400 V, 50 Hz Compressed air: 6.0 bar Dimensions (L x W x H): 2400 x 2300 x 1900 mm Weight: 1500 kg

Condition: ready for operation (used), Year of construction: 2009, functionality: fully functional, machine/vehicle number: 109, briquette diameter: 80 mm, overall weight: 1,450 kg, TECHNICAL DETAILS Briquette type Briquette diameter: 80 mm Motor power: 11 kW Production output: 80 - 210 kg/h Machine performance Cycles per minute: 7 Number of cylinders: 3 Max. discharge length: 70 mm Container Ring diameter: 1,200 mm Container capacity: 1 m³ MACHINE DETAILS Dimensions and Weight Dimensions (L x W x H): 2,100 x 1,350 x 1,600 mm Weight: 1,450 kg Gjdpfx Asxyi Ihomuoit Electrical Data Supply voltage: 400 V Frequency: 50 Hz Max. material moisture: 15 % EQUIPMENT Hydraulic oil machine Monoblock clamping system Capacitive sensor for automatic operation Viewing window End-of-cycle system Electronic pressure gauges for pump and clamping pressure Siemens touchscreen PLC Siemens display Operating hours counter Inductive limit switches LED machine position indicator Stamping unit Preheating system Oil level and temperature sensor Preparation for oil cooling in tank and material outlet Power stabilizer Service tools

Condition: used, Year of construction: 2023, No. 10017 Two-fraction star screen GÜNTHER MULTISTAR ONE / MS ONE Used, year of construction 2023 Approx. 200 operating hours Mobile star screen for screening waste wood, biomass, green waste and other screenable materials in 2-fractions as well as for overlength recycling - Input material: specific weight 200 - 650 kg/m³ / moisture max. 55% / piece size and individual weight max. 1000 mm and 20 kg / material feed with conveyor belt or wheel loader / throughput capacity up to 200 m³/h - Control, operation, switch cabinet: Type PLC / Operation display, control panel / Manual or automatic operating mode / Power supply AC 400 V, 3P, 50Hz via 32A plug on site - System interlinking: 16-pin plug connection / Cable (15 m) incl. winding device on base frame / Screen deck overrun for EMERGENCY STOP / Dummy plug in control cabinet door - Hydraulic support legs: 4 hydraulic support legs / Increase the discharge height of the useful fraction by 450 mm / All support legs can be controlled individually - Feed hopper: Capacity approx. 2.5 m³ / Feed height 2500 - 3000 mm / Free throw-in length 2300 mm / Conveying medium scraper chain conveyor with maintenance-free flat link chain / Drive 2.2 kW adjustable via frequency inverter - Collecting belt: Center distance 4600 mm / Belt width 1000 mm / Belt type smooth / motor 2.2 kW, v=1.2 m/s - Connect: Connect! is the innovative telematics solution from Komptech / overview of operating status, error messages, statistics, GPS localization, capacity utilization - Petrol-powered hydraulic pump - HyDrive System 2.0 MS ONE - Screen deck 60/90: Output: 0-60/90 and > 60/90 mm / Length 4500 mm / Width 1450 mm / Screen area 6.5 m² / Position 11° incline / Star shafts 17 pieces / Star diameter 340 mm / Star width 55 mm / Center distance 266.5 mm / Cleanstar cleaning elements / motor 2 x 4 kW / Adjustable via frequency inverter - Drive motors 50 Hz: motors for driving the screen deck / 2x 4 kW 50 Hz - Dosing roller: width 1560 mm / diameter 215 mm / drive 3 kW drum motor - FKAB with magnetic drum: Center distance 6200 mm / Belt width 1000 mm / Installation position 30° inclined / Belt type profiled, 15 mm chevron / 3.0 kW motor, v=2.2 m/s / Usable discharge height 3500 mm - 3950 mm / Multi-pole magnetic drum in permanent version / incl. discharge chute - Over-grain discharge conveyor: Center distance 6200 mm / Belt width 1000 mm / Installation position 30° inclined, 220° pivoting / Belt type profiled, 15 mm chevron / motor 3.0 kW, v=2.2 m/s / Usable discharge height 3600 mm - 4050 mm Transport dimensions approx. 8176 x 2466 x 2600 mm LWH Weight approx. 9200 kg Sale on behalf of customer, ex location near 85456 Wartenberg, without dismantling, transport and assembly Subject to errors in the description and price Dismantling, transport and loading by us optionally possible To avoid possible misunderstandings, an on-site inspection is possible and recommended by appointment Gsdpewhy T Tjfx Amusit Sold as is Technical details, condition description, year of manufacture and scope of delivery according to manufacturer's brochure or previous owner, without guarantee Subject to prior sale No warranty is given for used machines, the following applies: “purchased as viewed” Images and videos serve as examples and do not represent the actual scope of delivery Terms of payment: Prices excl. VAT, payment before collection or shipping Terms of delivery: ex location

Year of construction: 2021, condition: used, For sale: FM 3028 shrink wrap sealer from the renowned manufacturer ArkForm. This machine is designed for professional packaging of products in shrink film—ideal for manufacturing facilities, shops, wholesalers, and any environment where fast and visually appealing packaging is required. Technical data: • Model: FM 3028 • Manufacturer: ArkForm • Serial number: 202208631 • Year of manufacture: 2021 • Dimensions: 1000 × 620 × 1200 mm • Supply voltage: 230 V, 50 Hz • Power: 4.0 kW • Weight: 100 kg Description of operation: The machine seals the film and shrinks it onto the product at the same time. It features a heat chamber with a transparent cover for full monitoring and control of the packaging process. The film roll is mounted on the side of the unit, and the film guiding system allows for quick and convenient packaging preparation. Applications: Gedexlg Ntjpfx Amusit • Food packaging (bakeries, confectioneries, grocery stores) • Packaging of cosmetics, books, media, electronics, and other products • Protecting items from dust, moisture, and transport damage Condition: The machine is in very good technical condition, complete, and ready for operation.

Condition: new, Pro Sandblaster for Industry Pressure Unit SAPI Mammut Sandblasters with QUICK STOP™ System The SAPI Mammut sandblasters with the QUICK STOP™ system are powerful industrial sandblasting machines, designed for use in industries such as automotive, construction, and manufacturing. These machines ensure fast and efficient surface preparation, cleaning, and treatment of metal, concrete, and other materials. QUICK STOP™ – Safety & Protection The SAPI QUICK STOP™ system is a safety feature designed to prevent accidents and protect the machine from damage. It works by immediately stopping the blasting process as soon as the operator releases the control handle. This instantly cuts off the abrasive flow, preventing potential hazards and protecting the equipment from overuse-related damage. Efficiency & Durability The QUICK STOP™ system reduces air and fuel consumption, making the sandblasting process more efficient and cost-effective. The Mammut sandblasting machine is built for durability, featuring high-quality components that ensure consistent performance, even in harsh conditions. All our machines are fully CE- and TÜV-certified. Flexibility & Versatility The machine is available in different sizes to meet various sandblasting needs. It is compatible with a wide range of abrasive materials, from standard sand to specialized plastic or metallic media. The Mammut with QUICK STOP™ can be used for surface preparation, cleaning, and removing rust, paint, and coatings. Giodjupyw Eepfx Amuot Precision & User-Friendliness The Mammut with QUICK STOP™ allows for precise pressure control and adjustment during operation, ensuring consistent results and high accuracy. Additionally, inspection and maintenance access points are designed for easy upkeep. Maximum Safety The QUICK STOP™ system with a dead man’s switch ensures maximum safety during operation. It also prevents moisture buildup inside the machine, as pressure remains constant even when blasting stops—a major advantage over standard on/off blasting systems. Fully Equipped from the Start All Mammut sandblasters with QUICK STOP™ come fully equipped. Our standard package includes: ✔ Sandblasting hose ✔ Nozzle ✔ Pressure control valve ✔ Water separator ✔ Abrasive dosing valve ✔ Basic personal protective equipment