Used Moisture for sale (249)

Condition: used, Year of construction: 2019, Used machine Identical in construction to Weima C 150 Year of manufacture: 2019 1845 operating hours Equipment and technical data: Drive power: 5.5 kW Briquette diameter: 50 mm Hydraulic oil capacity: 160 l Throughput capacity: up to 50 kg/h (depending on material) Connection rating: 400 V +/- 5% / 50 Hz Itjdpfx Aew Rhk Dsacjn Includes: Press mechanism with filling cylinder, main cylinder, clamping cylinder Connection part for transport line Chromed clamp Hydraulic tank 160 l with pump motor + valve control Safety switch for oil temperature Control cabinet and electrical control system Briquette length monitoring Automatic end position for all cylinders Manual control Automatic "On/Off" with level limit switch Material: shavings, sawdust from solid wood, loose, clean and free from contaminants* Maximum dimensions: 10 mm Throughput performance: approx. 50 m³/year/ * Contaminant specification: Everything except wood, wood pieces larger than 15 mm. The throughput capacity is highly dependent on the material. Stated values are averages. May vary depending on mix ratio, moisture content, and material characteristics! Application case not known or not fully specified. Machine is being sold appropriately and solution-oriented by a specialist dealer. With oil cooler or water cooling; ensure adequate ventilation for the press/unit/oil cooler. In case of heat build-up, operating time may be drastically reduced due to increased temperature. With new press clamp Availability: by arrangement Location: Flörsheim

Condition: like new (used), Year of construction: 2016, operating hours: 4 h, machine/vehicle number: 84149090, Complete container station with screw compressor, ready for operation in industrial conditions, equipped with a full air treatment system. Ready for immediate start-up. Only 4 hours of test operation. CONTAINER 10" Specifications: Compressor: Ervor Rafale 50 SP (2016) – screw type, oil-lubricated, fixed-speed Motor power: 37 kW (50 HP) Capacity (FAD): ~260 Nm³/h at 7–9 bar Drive: Belt drive with automatic tensioner Power supply: 400 V / 3 phase / 50 Hz Dryer: Adsorption (2-column, regenerated, timer or DP-controlled) Aftercooler: Air-cooled compressed air aftercooler with ventilation Filtration: Pre-filter, fine filter, and final filter class 1 μm / 0.01 μm Container: 10 or 20-foot, steel, ventilated, insulated, with service doors Control: Control panel + pressure switch, hour meter, phase protection Technical condition: Very good Cold-regenerated dryer Adsorption dryer ERVOR – 2-column air drying system Integrated in the container station. Suitable for continuous operation, with automatic bed regeneration. Iodpfjw D Ut Hox Aacotn The set also includes an aftercooler and a complete set of filters (pre-filter, fine filter, final filter). System ready for industrial or military operation. Final humidity: ≤ -40°C PDP (pressure dew point) Air treatment and cooling system The station is equipped with a multi-stage compressed air treatment system, including: - 3-stage filtration (solid particles, oil, moisture), - Aftercooler with fan, - Insulated and serviceable pipelines, - Control manometers, ball valves, service bypasses, - System designed for heavy-duty use – industrial and mobile applications. Additional photos or video available upon request. We invite you to purchase.

Condition: new, Year of construction: 2025, Electric Pallet Truck 1500 kg – A Modern Solution for Internal Transport The CORMAK electric pallet truck, also known as an electric pallet jack, powered warehouse trolley, or electric pallet mover, is an essential device in any warehouse, store, wholesale outlet, or production facility. This model, with a 1500 kg load capacity, combines compact dimensions with high power and efficiency, ensuring fast and safe pallet transport over short and medium distances. With both electric drive and lifting, this pallet truck eliminates the need for manual pumping and pushing, significantly improving workplace ergonomics. It is ideal for environments where precision, quiet operation, and maximum productivity are essential. Modern 24V 20Ah Lithium-Ion Battery The 24V 20Ah lithium-ion battery offers long service life, short charging time, and requires no maintenance. Unlike traditional lead-acid batteries, Li-Ion cells allow for quick recharging at any time of day without the risk of shortening battery lifespan. As a result, the truck is always ready to work. The side-mounted battery further enhances the unit’s durability. This design effectively protects the battery from moisture, dust, and weather conditions, which is especially important when working in cold storage, loading docks, or open warehouse areas. The fully metal construction ensures exceptional resistance to mechanical damage. Its robust steel frame makes it perfect for tough working conditions – on construction sites, in workshops, or industrial plants where durability and safety are key. Key Features of the Pallet Truck Electric drive and lifting – minimal operator effort 1500 kg load capacity – ideal for most standard pallets 24V 20Ah lithium-ion battery – fast charging, long-lasting operation Side battery installation – better protection and easier maintenance All-metal construction – durability in harsh environments Compact and maneuverable design – excellent handling in narrow aisles Low noise and zero emissions – eco-friendly alternative to combustion-powered models Electric Pallet Jack for Warehouses, Stores, and Production Facilities This 1500 kg electric pallet jack is the perfect balance of performance and reliability. It’s ideal wherever work efficiency and operator safety are priorities. Whether you're looking for an electric-powered pallet truck, a warehouse trolley with drive, or an automatic pallet mover, this model offers maximum ease of use and low operating costs. Itjdpfjxphq Hsx Aacen Technical Specifications Specification Value Model Q15-4 Load capacity 1500 kg Fork height (raised) 200 mm Fork height (lowered) 85 mm Overall length 1670 mm Fork length 1150 mm Width 560 mm Minimum aisle width 1920 mm Turning radius 1480 mm Driving speed (with/without load) 3.8 / 4.2 km/h Max gradeability (with/without load) 2 / 6 % Drive motor power 0.75 kW Battery 24 V / 20 Ah Net weight 131 kg

Condition: like new (used), Year of construction: 2014, briquette diameter: 150 mm, overall weight: 3,000 kg, power: 30 kW (40.79 HP), Capacity: 450-500 kg/h Max. pressure force: 1700kg/cm2 Batch moisture content: 15% Length: 1800 mm Width: 1800 mm Height: 1900 mm Transport height: 2200 mm Iodjqd Uy Aspfx Aacotn Weight: 3000 kg Total power: 33 kW

Condition: new, Year of construction: 2025, type of input current: AC, power: 5.5 kW (7.48 HP), input voltage: 400 V, Pelleting plant for a wide variety of materials such as wood, miscanthus, agricultural by-products and waste products (hay, straw, maize straw ....) Animal feed ..... This is a complete system (compact system), which is built on a base frame and consists of the following components: Storage container for raw material 1.5 m³, incl. agitator Inclined mixer for raw material incl. level sensors and fully automatic moisture metering Dosing screw for optimum material feed to the press (speed-controlled) Isdpfoud Nx Hex Aacetn Press 5.5 kW, with horizontal round die, discharge chute with dust separation, temperature monitoring Conveyor belt for pellet removal, discharge height approx. 2.0 m The entire system is operated centrally using a Siemens PLC via touch display! In addition, all parameters are permanently monitored so that the system is shut down if a problem occurs! Price excl. VAT! The price includes operator and service training (in A-4352 Klam)! Attention, some of the pictures do not correspond to the actual system ( are example pictures ) !!!!! Attention!!! we are constantly looking for sales and service partners (worldwide) !!!!!

Condition: used, Year of construction: 2009, Fröling Turbomat 500 – wood-chip biomass boiler (2009) ⚙️ Technical data • 🔹 Model: Fröling Turbomat 500 • 📅 Year: 2009 • 🔥 Nominal output: 450 kW (W40) • ♨️ Maximum output: 495 kW • 💧 Water content: 750 litres • 🧱 Operating pressure: 6 bar • 🌡️ Max. temperature: 110 °C • ⚖️ Weight: approx. 6 800 kg • 🏭 Manufacturer: Fröling Heizkessel- und Behälterbau GmbH – Austria ⸻ 🔩 Main features Iedpfx Asxmrwfsacstn • ♻️ Fully automatic ash removal and heat-exchanger cleaning • 🔥 Four-layer, fireclay-lined high-temperature combustion chamber • 💦 Water-cooled feed channel – ideal for moist fuels • ⚙️ Moving grate for continuous and efficient combustion • 🌬️ Lambda control with multi-zone air regulation and low emissions • 🌀 Automatic draught and suction fan control • 🧰 Robust industrial design, easy to maintain • 🌲 Fuels: wood chips (G30–G50), pellets, sawdust, biomass ⸻ 💡 Advantages • ⚡ High efficiency, fully automatic operation • 🔧 Low maintenance, long service life • 🌫️ Reliable performance even with higher-moisture fuel • 🏢 Ideal for industrial and municipal heating systems ⸻ 📍 Location: Mosonmagyaróvár, Hungary

Condition: used, Used Bottling Line KRONES for Glass Bottles up to 20000 bph Introduction to the Bottling Line KRONES Initially, the used KRONES bottling line for glass bottles is highly sought after in industrial settings due to its reliability and efficiency. Comprising a range of top-tier components, the Complete Bottling Line KRONES ensures seamless performance, effectively meeting the stringent demands of high-volume production. Main Components Firstly, the KRONES K-131-669 filling monoblock, manufactured in 2016, stands as the centerpiece of the Complete Bottling Line KRONES. Capable of handling a remarkable 20,000 bottles per hour, it is complemented by the 1998 KRONES 472-072 depalletizer and the 2000 Gronemeyer RINSER 8983-400-4. Consequently, this collective setup facilitates a smooth and uninterrupted workflow from bottle unloading to the filling process in the Complete Bottling Line KRONES. Itjdpfxjvgvwmo Aacsn Quality Control of the Used Bottling Line KRONES Maintaining product quality is paramount in any bottling operation. Therefore, the 1999 KRONES CHECKMAT inspector plays a pivotal role in this regard in the Complete Bottling Line KRONES. With advanced functionalities encompassing not only level control but also meticulous label inspection, it ensures that every product meets the desired standards. Furthermore, the 2000 ACI TA20 2 AE bottle dryer guarantees that bottles are impeccably prepared for subsequent labeling and packaging stages, effectively eliminating any potential issues that may arise from moisture. Labeling and Packaging Efficient labeling and packaging are essential components of the KRONES bottling line. Consequently, the 1999 KRONES STARTMATIC K-080-669 excels in these areas. With precise label application capabilities, coupled with the ability to print directly onto glass bottles, it not only streamlines operations but also elevates brand presentation in the Used bottling line KRONES for glass bottles up to 20000 bph. Complementing this is the 1999 SMI SMI/7507 case packer and the 1997 FRANPACK Typ 121971214 pallet wrapper, ensuring that products are securely packaged and ready for distribution. Operational Status and Specifications The KRONES bottling line is in flawless working condition, and meets the demands of modern production environments. With a remarkable throughput of 20,000 bottles per hour, the line promises to enhance operational efficiency while maintaining product quality. Specifically designed for glass containers and primarily catering to beer production, it guarantees precise and consistent fills, ultimately resulting in superior product quality and customer satisfaction. In summary, the KRONES bottling line represents a sound investment for businesses seeking to optimize their bottling operations. With its robust construction, cutting-edge features, and proven track record, it is poised to deliver exceptional performance and elevate production standards to new heights.

Condition: used, overall weight: 18,000 kg, maximum load weight: 14,225 kg, axle configuration: 2 axles, loading space length: 6,611 mm, loading space height: 4,000 mm, first registration: 01/2019, total width: 8,511 mm, total height: 2,550 mm, Equipment: ABS, DOLL - 2-axle short timber trailer in "stool design" type A2G-10L500 (A131) Technical data: Dimensions: Total trailer length: 8,511 mm (with drawbar length 1,900 mm) Loading length: 6,611 mm Front overhang: 760 mm Rear overhang: 856 mm Vehicle width: 2,550 mm Wheelbase: 4,995 mm Load height top edge of frame loaded: 1,187 mm (with 275/70 R 22.5 tires) Overall height: max. 4,000 mm Weights: Perm. total weight: 18,000 kg Axle load (2 x 9t): 18,000 kg (techn. 24,000 kg) Unladen weight approx.: 3,350 kg (without stools and stanchions) Payload approx.: 14,650 kg Basic equipment:A2G DOLL - 2-axle short timber trailer in "stool design" - straight top chord Sturdy welded construction consisting of 2 longitudinal beams with straight upper chord. - Bogie with ball bearing rim - 1 wheel chock with bracket - Side underrun protection in accordance with ECE?R 737254461 Rear underrun protection: Aluminum underride guard, in accordance with ECE?R 58 Complete lighting and license plate holder installed in a protected manner, in accordance with ECE?R 487227407 Wheel cover: Complete plastic mudguards over the wheels, attached to the bogie at the front and to the main frame at the rear, with DOLL mud flaps behind the axles. Frame cover: Full-length aluminum duet plate cover (3/5 mm) bolted between the upper chords.7206867 Drawbar GZY27: Drawbar fork with silent bushing bearings and drawbar support, type GZY 27drawbar eye: Length: D-value: Maximum front axle load: Maximum total weight:Ø 50 mm (heavy-duty ECE) 1,900 mm 125 kN 10 t 27 t Connecting cable to the truck: routed along the drawbar (air, light, ABS). Cable routing: Brake and electrical cables routed protected on the main frame. Grapple bracket: Angled grapple bracket at the front, reinforced. Mud flap: Continuous mud flap at the end of the vehicle, swinging, with ?DOLL? log Chassis / Chassis:12 t Chassis: 2 single axles, BPW, 12 t with drum brakes, both axles with ABS and AGS, including safety ropes. Suspension type SL, with 2 x 43 mm trailing arms. Air suspension: Air suspension without lifting and lowering. Weight display without Smartboard: EBS-E weight display for trailers with air suspension, consisting of 2 pressure sensors to determine the axle loads. The axle loads are transmitted to the truck via CAN-BUS for weight display in the truck display. (Truck equipment not included in the scope of delivery!) Brake system: Electronically controlled 2-line air brake system (EBS-E). Brand name, load-dependent, including ABS. EBS system completely installed, spring-loaded parking brake, can be operated via parking release safety valve, as well as from the cab (truck-side installation not included in scope of delivery!) Aluminum air tank Brake connection: 1 duomatic clutch head. Itjdpfx Aajw U Tv Hjcjn Tires: Tires (85.50 kg / piece): 8 pieces tires 275/70 R 22.5 make Continental Hybrid HS3 on steel rim 8.25 x 22.5. Stools / stanchions: Stool: 6 pieces ECCO? steel stool body with 2° stanchion inclination type Kombi 7 (80.0 kg), with bracket ? Clamp fastening on the main frame including 1 pair of hooks for load securing. Stanchions: ECCO aluminum stanchions type ALU 7, screwable, fixed dimension stanchions. Basic height 2,550 mm (21.0 kg). Maximum loading capacity per pair of stanchions 7t. Electrical equipment / lighting: Lighting system: Conventional wiring of the trailer to increase the quality standard. ? Long service life ? Insensitive to moisture and dirt ? Minimal maintenance ? Quick and easy repair in rare serv

Condition: used, Year of construction: 2019, operating hours: 4,000 h, functionality: fully functional, machine/vehicle number: BP 500 A, DESCRIPTION BRIQUETTING PRESS The press is designed for compacting secondary raw materials into briquettes (briquette shape: rectangular). Technical data of the press: Dimensions: Length: 1800 mm (2100 mm during transport) Width: 1800 mm (2000 mm during transport) Height: 1900 mm (2200 mm during transport) Net weight: 2945 kg Power supply: 380 V 50 Hz 33 kW 70–100 A Output capacity: 450 kg/h (+/-50 kg depending on the type and fraction of raw material) Noise level: A-weighted sound pressure level at the workplace: 77.8 dB +/-5 dB Compression force: Minimum: 1000 kg/cm² Maximum: 1700 kg/cm² Pressure: Max. 300 bar Maximum raw material moisture: Not more than 14% Itedpjxmav Nefx Aacsn Briquette dimensions: Width: 150 mm Thickness: 60 mm Length: 40–105 mm Permissible operating ambient temperature: -20°C to +35°C (up to +50°C with additional cooling system) The press consists of: Electrical system — controls the hydraulic press system. Equipped with four electric motors: the first (30 kW) is for driving the main hydraulic pumps; the second (1.1 kW) is for the cooling pump; the third (0.55 kW) is for the fan of the oil cooling system; the fourth (1.5 kW) is for driving the sawdust feeding screw. The operation of the motors and hydraulic valves is controlled via contactors and intermediate semiconductor relays by a microprocessor with expansion modules. A liquid crystal display with buttons is provided for visualization and parameter adjustment. Hydraulic system — controls the operation of hydraulic cylinders using pumps, high and low-pressure lines, solenoid hydraulic valves, and hoses. There are three hydraulic cylinders: the first (main), designed for pressing sawdust; the second (vertical), for the preliminary compaction of sawdust; the third (forming), for transferring briquettes to the mold. An oil cooling system with pump and air cooler is also installed. Oil filtration is provided by the main high-performance filter, a cooling system filter, and a fine filter. Feeding of raw material is provided via a feed hopper integrated in the press. The raw material entering the hopper is intermittently mixed to prevent bridging. The agitator is driven via a chain from the screw drive motor-reducer. The screw cyclically feeds raw material into the vertical cylinder shaft. The hopper is equipped with two level sensors (lower and upper). If the hopper is enlarged, the sensors can be relocated as needed. Control — dual operation: manual and automatic. All control equipment is installed in the electrical cabinet. Automatic control is the standard operating mode of the press without operator intervention. Manual control is intended for press setup, fault detection, cylinder reset, or in case of emergency. Operation is simplified by the display located on the cabinet door, which allows the user to view and modify parameters and monitor the condition and errors of the press.

Condition: ready for operation (used), Year of construction: 1996, Printing units outside/inside: 2/1, doctor blade units: 3, production capacity: 800 envelopes/min, window unit: Mini-Splice 356 CMG, roll/splicer: Winkler + Dünnebier 191, web guiding: BST EKR 1000, gumming: standard remoist (moisture-activated gumming for sealing flaps), ink pumps: 2, extraction: window punching waste. Documentation available. An on-site inspection is possible. Isdpfsxbrxfsx Aacstn

Condition: ready for operation (used), Engineered for high efficiency, the Steris VHP-100R Desiccant Regeneration System, Model RG120 regenerates desiccants used in vaporized hydrogen peroxide (VHP) sterilization, ensuring consistent and reliable moisture control. The RG120 is designed to maintain optimal performance of your VHP sterilization equipment, enhancing overall process efficiency and efficacy. Its robust construction, user-friendly interface, and advanced regeneration technology make the Steris VHP-100R Desiccant Regeneration System an essential component for any facility relying on VHP sterilization for critical applications. Good working condition. Please check out our other listings as well. Isdsw Rg Etepfx Aacjtn

Condition: new, Year of construction: 2025, LUFT 1500 COMPACT Screw Compressor with Refrigerated Air Dryer The LUFT series screw compressor by the Polish brand Cormak represents the latest innovations in pneumatics, combined with the use of high-quality materials and components. Low operating costs, ease of use, ergonomic and robust design, and high performance guarantee efficient and trouble-free operation. Key Features of the Screw Modules in CORMAK Compressors: Modern Technology and Efficiency The screw modules ensure excellent performance and outstanding energy efficiency. Their design focuses on maximizing output while minimizing energy consumption. Precision and Control Thanks to advanced engineering solutions, the screw modules allow for precise control of the compressed air generation process. This translates into stable pressure and optimal operation of the entire pneumatic system. Durability and Reliability The screw modules used in CORMAK compressors are built for longevity. Their sturdy construction and use of high-grade materials ensure reliability even under harsh industrial conditions, minimizing downtime and the need for frequent repairs. Integrated Refrigerated Air Dryer – Top-Level Air Quality Itodpfx Aasxnk Acscsn Two-Stage Drying System Effectively removes moisture and protects the pneumatic system. Variable-Speed Fan Automatically adjusts cooling capacity according to operating conditions, resulting in energy savings. Dual Filtration System A pre-filter with 3.0 µm accuracy removes larger solid contaminants. A precision filter with 0.1 µm accuracy captures fine oil particles (aerosols) and other impurities, ensuring ultra-clean air. Technical Specifications: Parameter Value Motor Power 11 kW Voltage 400V / 50Hz Output (0–6 bar) 1620 L/min Output at 6 bar 1580 L/min Output at 8 bar 1350 L/min Output at 10 bar 1230 L/min Outlet Connection Diameter (G) 1" Dimensions 1550 x 740 x 1150 mm Weight 500 kg Manufacturer: CORMAK

Condition: used, operating hours: 11,000 h, Used SIDEL Bottling Line for Still Water up to 54000 Bottles per Hour Introduction of the Used bottling Line SIDEL for still water up to 54000 bph The used SIDEL bottling line for still water up to 54000 bottles per hour is currently built in 2014 operational and offers high performance. Specifically designed to package still water in 0.5 liter PET bottles, this line meets the needs of large scale production. Moreover, the Sidel water line reaches a production speed of 54000 bottles per hour, thereby optimizing operational efficiency for high quality products. Isdpfx Ajvgvcpeacetn Filling Technology and Bottle Specifications This Sidel water line employs gravity filling technology with light depression, ensuring precise and consistent dosing of the product. Additionally, the bottle neck type is the standard 30. or 25, which is common in the bottling industry. Having operated for a total of 10000 hours, the line has demonstrated reliability and robustness over time. With 24 blowing cavities and 84 filling nozzles, it significantly increases production capacity. Main Components of the Line At the core is the 2014 SIDEL Combi SBO24 Matrix system, which combines blowing, filling, and capping functions in a compact unit. Configured with 24 blowing cavities and 84 filling nozzles, it optimizes productivity, allowing the used SIDEL bottling line for still water up to 54000 bottles per hour to operate at full capacity. Cleaning and Preparation Systems Furthermore, the CIP system provided by Beijing Sanyuan of the Sidel water line ensures automated cleaning of parts in contact with the product, which is essential for maintaining hygienic standards in bottling still water. The SH Yiwei bottle dryer removes residual moisture, thus preparing the bottles for subsequent stages. Together, these components contribute to the overall efficiency of the line. Marking and Quality Control A DOMINO laser bottle printer allows direct marking on the bottles with clear and indelible information. Haifu inspectors control the filling level and verify correct label application, thereby ensuring the quality of the final product. Consequently, the used SIDEL bottling line for still water up to 54000 bottles per hour maintains high quality standards. Labeling and Traceability of the Used bottling Line SIDEL for still water up to 54000 bph Moreover, the 2014 SIDEL ROLLQUATTRO labeling machine uses roll fed labeling technology, allowing rapid and precise label application. An additional DOMINO printer prints on cartons, providing necessary codes and information for logistics and traceability. As a result, this setup makes the Sidel water line a complete solution for the entire packaging process. Packaging and Weighing Systems An OCME case packer automates the packing of bottles into boxes for this Sidel water line. Additionally, the SARTORIUS scale provides accurate weight measurements, which are essential for quality control.

Condition: excellent (used), Year of construction: 2012, functionality: fully functional, Air dryer AGRE KOMPRESSOREN ADD 3000 (18) – 13 bar | 11.18 kW | 2012. I will sell an industrial air dryer AGRE KOMPRESSOREN ADD 3000 (18), manufactured in 2012. The device is an ideal solution for compressed air systems, ensuring effective moisture removal and improvement of air quality in pneumatic installations. Technical data: ✅ Model: ADD 3000 (18) ✅ Manufacturer: AGRE KOMPRESSOREN GmbH (Austria) Itodpfxjv Dr I Aj Aacsn ✅ Year of manufacture: 2012 ✅ Weight: 550 kg ✅ Power: 11.18 kW ✅ Voltage: 400 V / 50 Hz / 3 phases ✅ Working pressure: 13 bar ✅ Maximum pressure: 13 bar ✅ Maximum inlet temperature: 55°C ✅ Maximum ambient temperature: 45°C ✅ Refrigerant: R404A (10.5 kg) ✅ Country of manufacture: Italy Condition and use: The dryer is in good technical condition, ready to work.

Condition: used, Year of construction: 2009, Speed / U/min. intake pressure / bar weight / kg total power requirement / kW Complete compressed air system - screw compressor + refrigeration dryer (Drypoint RA 500) + 2x compressed air boilers (3,000 litres each) Make: COMPAIR Motor power: 75 kW Type: LL80 7.5A Year of manufacture: 2009 Serial no.: CD1000057200 Control system: Delcos 3100 Refrigeration dryer: Drypoint RA 500 Compressed air tank: 2x galvanised tanks, 3,000 l each - total volume 6,000 l Load hours: 79,495 This compressed air system from COMPAIR offers a powerful and efficient solution for industrial applications with high air requirements. LL80 7.5A screw compressor: The compressor with a motor output of 75 kW is robust, low-maintenance and designed for continuous use. Its modern technology ensures a stable and consistent compressed air supply even under high loads. Ideal for production facilities, workshops or other industrial areas. Itedpfxjud Iwzo Aacjn Delcos 3100 control unit: This intelligent control unit makes it easy to operate, monitor and adjust the compressor. It ensures optimum operation, energy efficiency and protection of the system against damage. Drypoint RA 500 refrigeration dryer: An integrated refrigeration dryer is essential for removing moisture from the air. This protects downstream machines and tools from corrosion and extends the service life of the entire system. Compressed air tank - 2x galvanised tanks with a volume of 3,000 l each: The two robust, galvanised tanks offer a large storage capacity of 6,000 litres in total. This keeps the pressure stable and maximises performance.

Year of construction: 2021, condition: used, For sale: FM 3028 shrink wrap sealer from the renowned manufacturer ArkForm. This machine is designed for professional packaging of products in shrink film—ideal for manufacturing facilities, shops, wholesalers, and any environment where fast and visually appealing packaging is required. Technical data: • Model: FM 3028 • Manufacturer: ArkForm • Serial number: 202208631 • Year of manufacture: 2021 • Dimensions: 1000 × 620 × 1200 mm • Supply voltage: 230 V, 50 Hz • Power: 4.0 kW • Weight: 100 kg Description of operation: The machine seals the film and shrinks it onto the product at the same time. It features a heat chamber with a transparent cover for full monitoring and control of the packaging process. The film roll is mounted on the side of the unit, and the film guiding system allows for quick and convenient packaging preparation. Applications: • Food packaging (bakeries, confectioneries, grocery stores) Itsdpjxlg Ntjfx Aacjn • Packaging of cosmetics, books, media, electronics, and other products • Protecting items from dust, moisture, and transport damage Condition: The machine is in very good technical condition, complete, and ready for operation.

Condition: new, Pro Sandblaster for Industry Pressure Unit SAPI Mammut Sandblasters with QUICK STOP™ System The SAPI Mammut sandblasters with the QUICK STOP™ system are powerful industrial sandblasting machines, designed for use in industries such as automotive, construction, and manufacturing. These machines ensure fast and efficient surface preparation, cleaning, and treatment of metal, concrete, and other materials. QUICK STOP™ – Safety & Protection The SAPI QUICK STOP™ system is a safety feature designed to prevent accidents and protect the machine from damage. It works by immediately stopping the blasting process as soon as the operator releases the control handle. This instantly cuts off the abrasive flow, preventing potential hazards and protecting the equipment from overuse-related damage. Efficiency & Durability The QUICK STOP™ system reduces air and fuel consumption, making the sandblasting process more efficient and cost-effective. The Mammut sandblasting machine is built for durability, featuring high-quality components that ensure consistent performance, even in harsh conditions. All our machines are fully CE- and TÜV-certified. Flexibility & Versatility The machine is available in different sizes to meet various sandblasting needs. It is compatible with a wide range of abrasive materials, from standard sand to specialized plastic or metallic media. The Mammut with QUICK STOP™ can be used for surface preparation, cleaning, and removing rust, paint, and coatings. Precision & User-Friendliness The Mammut with QUICK STOP™ allows for precise pressure control and adjustment during operation, ensuring consistent results and high accuracy. Additionally, inspection and maintenance access points are designed for easy upkeep. Itsdpfsupyw Esx Aacen Maximum Safety The QUICK STOP™ system with a dead man’s switch ensures maximum safety during operation. It also prevents moisture buildup inside the machine, as pressure remains constant even when blasting stops—a major advantage over standard on/off blasting systems. Fully Equipped from the Start All Mammut sandblasters with QUICK STOP™ come fully equipped. Our standard package includes: ✔ Sandblasting hose ✔ Nozzle ✔ Pressure control valve ✔ Water separator ✔ Abrasive dosing valve ✔ Basic personal protective equipment

Condition: reconditioned (used), Year of construction: 2003, functionality: fully functional, briquette diameter: 60 mm, Reconditioned machine suitable for smaller single-shift joinery operations. It offers a robust construction with good performance. Max. briquette production 70 kg/hour. Year of manufacture 2003. Very good and preserved condition. Original warranty and after-sales service directly from our company. PRODECO professional hydraulic briquetting presses are suitable for small and medium-sized wood processing plants. They allow efficient processing of waste into ecologically clean and high calorific fuel without the use of binders. They are characterized by low space requirements, low energy consumption and simple operation. Technical data: Iedpfx Aovva Rpjacstn Engine power: 5.5 kW Briquette production: 35 to 70 kg/hr depending on material Briquette diameter: 60 mm Briquette steps max 60 mm (infinite briquette) Hopper diameter: 1000 mm Weight 650 kg Machine dimensions: 1170 x 1700 x 1510 mm Features: Hydraulic unit 7 press cycles/min. Double pressure gauge for better pressure control. Level probe for briquetted material Probe for oil level height Inspection window CE safety standard Moisture content of the material to be processed must not exceed 18% Machine is fully reconditioned, adjusted, and tested.

Condition: used, Used Bottling Line Tehnometal up to 6500 bph The bottling machinery, known as Used Bottling Line Tehnometal up to 6500 bph, provides a highly efficient solution for the bottling industry. This plant, comprising high-quality components and featuring advanced technical specifications, ensures optimal performance and long operational life. Blower KRUPP Corpoplast Blomax 6 of the Used Bottling Line Tehnometal The Blower KRUPP Corpoplast Blomax 6, produced in Germany in 1999, underwent general repairs in 2016 after purchase. Consequently, this component has a capacity of 6,500 bottles per hour (bph) for 1.5-liter bottles and 7,000 bph for 0.5-liter bottles with 6 cavities. The blower includes a cooler but lacks a compressor. Furthermore, the available molds allow for the production of 0.5, 1.5, and 2.0-liter bottles. An air conveyor, 40 meters long, connects the blower to the monobloc. Monobloc TEHNOMETAL The monobloc TEHNOMETAL, produced in Serbia in 2014, integrates rinsing, filling, and capping functions. Moreover, this component matches the blower’s capacity, handling 6,500 bph for 1.5-liter bottles. The monobloc accommodates PET bottles with a 28 mm neck and PCO 1810 neck. Its configuration, therefore, ensures continuous and smooth production, enhancing the efficiency of the bottling line. Labeller TEHNOMETAL The labeller TEHNOMETAL, produced in Serbia in 2015, applies OPP (oriented polypropylene) labels directly from the roll. This system, hence, ensures perfect label adhesion and a high-quality finish for each bottle. Using OPP labels guarantees durability and moisture resistance, thus enhancing the presentation of the final product. Itsdpfjvgvq Hjx Aacen Shrink Wrapper TEHNOMETAL The shrink wrapper TEHNOMETAL creates packages of 2×3 and 3×4 bottles. This component securely wraps the packages in shrink film, protecting the bottles during transport and storage. The flexibility in package configurations, as a result, offers versatile packaging options to meet different market needs. Conveyor Belts and Technical Documentation The conveyor belts included in the Used Bottling Line Tehnometal up to 6500 bph ensure a continuous flow of bottles between the various components of the system. The detailed technical documentation provides all the necessary information for installation, maintenance, and operation of the bottling line. This documentation, in turn, enables technicians to effectively manage the machinery, reducing downtime and increasing productivity. Spare Parts and Space Requirements The available spare parts allow for quick resolution of any faults, minimizing machine downtime. The machinery installation requires a space of 200 m², thereby ensuring sufficient room for operation and maintenance. The compact design of the system allows efficient use of available space, making the machinery suitable for various plant configurations. Conclusion of the Used Bottling Line Tehnometal In conclusion, the Used Bottling Line Tehnometal up to 6500 bph provides a complete and highly efficient solution for bottling needs.

Condition: new, New, never used pellet making machine for sale! It can be ordered with a 6 mm or 8 mm sticker (1 piece optionally comes with the machine). Pellet production capacity up to 400-450 kg/hour depending on the raw material. Iedpexmhx Esfx Aacotn Pellet diameter:3mm, 4mm, 5mm, 6 mm or 8 mm (depending on the chosen sticker). 3mm, 4mm, 5mm, 6mm sticker with roller as a set for the machine for 2000 euros. Sticker diameter: 300 mm. Adjustable pellet length: 10-30 mm. Engine power: 22 kW. Dimensions: 1400 mm x 1000 mm x 1200 mm. Weight: 750 kg. Raw material moisture: 10-12-14%. The moisture content affects the quality of the pellets. Dph3O7 Raw material size: Saw dust: 1-3 mm, straw: 3-6 mm. The density of the granules is no more than 1250/m3. It is located locally in Budapest (EU), Hungary.

Condition: new, Year of construction: 2025, Our SAPI "Mammut" pressure blaster with a 100-liter tank capacity is suitable for all common blasting media. The blasting pressure can be continuously adjusted from 0.1 to 12 bar using the built-in pressure regulator. A water separator is also permanently installed on the blaster, which separates moisture from the compressed air and prevents the blasting media from clumping due to excessive moisture. Our safety shut-off system ensures safe operation of the sandblaster. This starts and stops the blasting process by operating the hand lever mounted on the blasting hose. The pressure blaster is delivered fully operational, assembled in a space-saving mesh box. All that's required is to connect the compressed air supply and fill it with blasting media. It can be easily transported by forklift or pallet truck. A lockable aluminum box is installed for storage of protective clothing, spare parts, etc. The scope of delivery includes: SAPI "Mammut 100 L" pressure blaster 1" pressure regulator, permanently mounted 1" water separator, permanently mounted SAPI safety shut-off device Abrasive sieve Cover 10 m blast hose, fully assembled, ø 25x7 mm Silicon carbide Venturi long nozzle, diameter optionally 6 mm, 8 mm, or 10 mm RED 2 sandblasting helmet Nylon/cotton sandblasting overalls 1 pair of leather blasting gloves 10 m breathing air hose, fully assembled SAF breathing air filter/activated carbon filter Wearing parts set consisting of: 100 tear-off films for RED 2 10 inner discs for RED 2 1 blast hose coupling, 25x7 mm nylon 2 rubber seals for blast hose coupling 1 nozzle holder, 25x7 mm Grid box with blast hose holder Aluminum box Lockable Technical specifications of the pressure blaster: Precisely adjustable from 0.1 - 12 bar TÜV-certified with certificate Fixed 1" internal and external piping Rubber-coated metal cone with rubber seal Large hand hole Rubber-wheeled chassis Abrasive dosing valve (suitable for all common blasting media) Capacity: 100 l Total height: 1,130 mm Itodpfxowc Ri Is Aacen Bowl diameter: 490 mm Total diameter: 900 mm Weight: approx. 75 kg Dimensions of the mesh box: Length: 1,460 mm Width: 840 mm Height: 1,400 mm Total weight including all accessories: 260 kg

Condition: used, Year of construction: 2010, Used Injection Molding Machine SIPA PP2 72 year 2010 The SIPA PP2 72 injection molding machine from 2010, currently operating until April 2025, provides an efficient and precise solution for producing PET preforms. As a result, the system ensures high performance in the bottling industry, thanks to its advanced technical setup and specialized components. This Used Injection Molding Machine base features the PPS 72 model, equipped with a rotary robot dedicated to optimal preform cooling. Specifically, this integrated cooling system maintains consistent dimensional quality, shortens cycle times, and ensures high production volumes without compromising technical specifications. Moreover, in this Used Injection Molding Machine, the preform discharge conveyor alternates between two octabins, optimizing space and minimizing material handling times. Hot Runner and Customized Cold Half Plate of this Used Injection Molding Machine In the Used Injection Molding Machine SIPA PP2 72 year 2010, the 72-cavity hot runner maximizes productivity and ensures uniform plastic flow distribution. The system includes a complete cold half, consisting of: The core plate, which ensures proper preform shaping. The lip plate, which delivers precision and flexibility during the injection process. The cavity plate, customized to produce a wide range of preforms according to customer requirements. In addition, this setup allows quick modifications and minimizes downtime, increasing overall system efficiency. Consequently, operators can achieve high production rates while ensuring adaptability to various production needs. PET Dryer and Environmental Control The DP820P HT dryer, manufactured by Plastic Systems, and equipped with a H6000 hopper, handles PET drying. Importantly, this dryer, installed in 2010, dehumidifies the plastic material, ensuring proper preparation before the injection process. Indeed, controlling the PET’s moisture content is essential to prevent structural defects and achieve high mechanical properties in the preforms. At the same time, the Eisbar DAS – E23 air conditioning unit, also from 2010, manages the cabin’s environmental conditions by regulating temperature and humidity. Therefore, this system ensures stable conditions and prevents variations that could compromise the quality of the final product. Similarly, it contributes to overall operational stability by reducing potential production inconsistencies. Mezzanine for Optimal Component Arrangement Itodov Ai I Ropfx Aacjn The system includes a mezzanine that houses the dryer and cabin air conditioner. As a result, this platform provides an ergonomic and organized layout of the various components, simplifying both routine and extraordinary maintenance while freeing up floor space in the production area. Furthermore, this arrangement enhances safety by reducing equipment-related congestion on the production floor.

Condition: new, Year of construction: 2025, functionality: fully functional, Our powerful "MM 2010" sandblasting cabinet uses a pressure blasting process and, thanks to its innovative media recirculation system, is suitable for all types of blasting media. Thanks to the bucket elevator permanently connected to the cabinet, even the heaviest types of blasting media, such as stainless steel, cast steel, and other metallic media, can be used without any problems. Unlike competing systems, the blasting media is not sucked back into the cabinet, but rather transported to the adjacent bucket elevator via a flat conveyor system. The bucket elevator conveys the material upwards and throws it into the cyclone separator, where the blasting media is cleaned and returned to the blasting process. Our specially developed media recirculation recycling system ensures continuous media flow, regardless of the extraction system's suction power. Itodpfx Aaowc Nrnocjn Thanks to the media recirculation system and the innovative fan technology, the blasting cabinet has very low energy requirements (0.75 kW fan motor). Since the blasting material is not sucked back in, no oversized extraction system with high power consumption is required (as with many competitive systems). To achieve maximum blasting performance, the "MM 2010" pressure blasting cabinet is equipped with a 60-liter pressure blasting tank. This is equipped with a pressure regulator for continuously adjusting the blasting pressure from 0.1 to 12 bar. For safe operation, a water separator is permanently mounted on the blasting tank, protecting the blasting media from moisture. The pressure blasting nozzle is made of highly wear-resistant boron carbide and allows a service life of up to 1,000 hours, depending on the blasting media used. The blasting chamber is equipped with a wear-resistant rubber lining, which increases the service life of the blasting media and protects the blasting cabinet from wear. An air blow gun is installed for cleaning the blasted workpieces and blowing off the cabinet walls. The permanently installed cartridge filter extraction system ensures optimal visibility in the blast chamber and maximum abrasive service life. The extraction system features continuous cleaning of the filter cartridges using compressed air blasts. This ensures a long service life of the filter media and consistently consistent extraction performance. The blast chamber is loaded via an angled front flap that swings completely upwards. This allows the blast cabinet to be loaded using a forklift or crane. The sturdy work grate can support a maximum load of 500 kg. To ensure optimal visibility in the blast chamber, two powerful and energy-saving LED lights are mounted on the cabin roof. Their roof-mounted design protects them from dust and wear. The system is operated via a modern touchscreen display. To ensure safe operation of the blast cabinet, the blast cabinet is equipped with a door safety switch. The installed viewing windows are made of toughened safety glass and are provided with a wear-resistant film.

Condition: new, Year of construction: 2025, Our SAPI "Mammut" pressure blasting unit with a 200-liter tank capacity is suitable for all common blasting media. The blasting pressure can be continuously adjusted from 0.1 to 12 bar using the permanently installed pressure regulator. A water separator is also permanently installed on the blasting unit; this separates moisture from the compressed air and prevents the blasting media from clumping due to excessive moisture. Our safety shut-off device is included for safe operation of the sandblaster. This starts and stops the blasting process by operating the hand lever mounted on the blasting hose. Included in delivery: SAPI pressure blasting unit "Mammut 200 L" 1 1/4" pressure regulator, permanently mounted 1 1/4" water separator, permanently mounted SAPI safety shut-off Technical specifications of the pressure blasting unit: Precisely adjustable from 0.1 - 12 bar TÜV-tested with certificate 1 1/4" fixed piping inside and outside Rubber-coated metal cone with rubber seal Generous hand hole Rubber-coated metal cone with rubber seal Large hand hole Rubber-wheeled chassis Abrasive dosing valve (suitable for all common blasting media) Capacity: 200 l Total height: 1,420 mm Vessel diameter: 600 mm Total diameter: 1,000 mm Weight: approx. 140 kg ADVANTAGES OF THE SAPI PRESSURE BLASTING UNIT with safety shut-off Fastest start-up and shutdown times while maintaining compliance the regulations of the professional associations (VBG 48) The pressure setting can be precisely adjusted before blasting – continuously adjustable from 0.1 to 12.0 bar Lower abrasive consumption, as the pressure vessel remains permanently pressurized and there is no unnecessary run-on time Upon restart, full blasting pressure is immediately available at the nozzle – no pressure build-up necessary → lower consumption & less wear on the hose No condensate formation in the vessel, as it remains constantly pressurized → no venting or venting with every start/stop Itodpewc Rk Eefx Aacsn Optimal abrasive dosing with a hardened fine dosing valve Less compressed air required → noticeably lower diesel consumption One-person operation, as the pressure can be displayed and adjusted directly on the pressure gauge – even without starting No failure-prone components such as control valves, diaphragms, or seals → easy to maintain and reliable Only the blasting hose in the safety shut-off device needs to be checked and replaced if necessary

Condition: new, Our SAPI "Mammut" pressure blasting unit with a 60-liter tank capacity is suitable for all common blasting media. The blasting pressure can be continuously adjusted from 0.1 to 12 bar using the permanently installed pressure regulator. A water separator is also permanently installed on the blasting unit; this separates moisture from the compressed air and prevents the blasting media from clumping due to excessive moisture. Ijdpfx Aewc Afheacjtn Our safety shut-off device is included for safe operation of the sandblaster. This starts and stops the blasting process by operating the hand lever mounted on the blasting hose. Included in delivery: SAPI pressure blasting unit "Mammut 60 L" 1" pressure regulator, permanently mounted 1" water separator, permanently mounted SAPI safety shut-off Technical specifications for the pressure blasting unit: Precisely adjustable from 0.1 - 12 bar TÜV-tested with certificate 1" fixed piping, internal and external Rubber-coated metal cone with rubber seal Generous hand hole Rubber-coated metal cone with rubber seal Large hand hole Rubber-wheeled chassis Abrasive dosing valve (suitable for all common blasting media) Capacity 60 l Total height 1,130 mm Bowl diameter 360 mm Total diameter 700 mm Weight approx. 60 kg ADVANTAGES OF THE SAPI PRESSURE BLASTING UNIT with safety shut-off Fast shut-off and start-up times, while complying with the regulations of the professional associations (VBG 48) Pressure setting Can be precisely adjusted before the actual blasting process, continuously adjustable from 0.1 to 12.0 bar. Reduced abrasive consumption, as the pressure vessel remains permanently pressurized, thus eliminating unnecessary abrasive run-on. Upon restart, the full blasting pressure is immediately available at the nozzle and does not need to be slowly built up. This significantly reduces abrasive consumption and significantly reduces wear on the blasting hose. No moisture (condensate) builds up in the vessel, as the vessel remains constantly pressurized and is not vented and vented with every start and stop. This process also offers other advantages, such as: Optimal abrasive dosing with a hardened fine dosing valve Lower compressed air consumption, thus significantly reducing fuel consumption (diesel) One-person operation, as the blasting pressure is constantly displayed by the vessel pressure and can be easily adjusted on the pressure gauge without prior start-up. No failure-prone components such as control valves, diaphragms, or seals, making it easy to maintain and reliable. Only the blasting hose needs to be checked in the safety shutoff and replaced if necessary.