Used Metal Material for sale (47,437)

Condition: used, GENERAL INFORMATION Iodpfx Aoxqdpujg Dja Comments: Internal width: 5,940 mm • Internal depth: 2,000 mm • Internal height: 2,000 mm • Exterior walls and roof: trapezoidal galvanized sheet metal • Interior walls: trapezoidal galvanized sheet metal • Interior ceiling: trapezoidal galvanized sheet metal • Floor: wooden floor made of tongue-and-groove planed boards • Roof drainage: via longitudinal gutters • Door type: double-leaf door Total width: 2,170 mm Total height: 2,150 mm Total length: 6,080 mm Location: Bremen Condition: used

Condition: used, Pay-off and take-up decoiler for coil material WANZKE CAMU Type SC 515/M Serial no. 8487 Year of manufacture: 2006 Coil weight approx. 1,500 kg Maximum coil width: 600 mm Coil inner diameter: 370 - 640 mm Maximum coil outer diameter: 1,800 mm Mandrel shaft diameter: 90 mm Distance from mandrel crown center to mandrel base: 950 mm Mandrel crown speed: 13 rpm Motor speed: 920 rpm Iodpfx Agswvv Rqj Dsa Gearbox transmission ratio: 1:70 Mandrel drive motor power: 1.1 kW Power supply: 400 Volt, 50 Hz - Mechanical expansion of the mandrel crown with hand crank - Drive via geared motor with worm gearbox, directly mounted on the mandrel shaft - Geared motor with electric brake - Mandrel shaft with mechanical slip clutch, pre-tensioned and adjustable via disc springs - Mandrel crown without strip travel arms - Without electrical control system and without loop switch Space requirement (L x W x H): 1300 x 800 x 1230 mm Weight: 380 kg Good condition

Condition: used, Strip Processing Line, Decoiler and Straightening Machine Year of manufacture: 1991 Strip width: 50 to 450 mm Sheet thickness with straightener inactive: 6 mm Sheet thickness with straightener active: 2 mm - Very well equipped with feed-in aids Required floor space for the entire line (L x W): approx. 7000 x 3000 mm Total weight: approx. 11 tons Good condition Straightening Machine HMS Type RS 47-04/1, Machine No. Strip width, nominal: 400 mm Strip width, max. pass-through: max. 455 mm Strip thickness at 400 mm width: max. 1.5 mm (steel) Strip thickness at 400 mm width: max. 2 mm (copper) Speed: max. 40 m/min Number of straightening rolls: 7 Straightening roll diameter: Ø 40 mm Number of pinch rolls: 2 Pinch roll diameter: Ø 80 mm Entry height/pass-through height: 1500 mm - Straightening rolls hardened, ground and hard-chromed, with central support - Pinch rolls hardened, ground and hard-chromed, with hydraulic lifting - Manual straightening roll adjustment - Feed assist with hydraulically extendable tongue and hydraulically adjustable deflection pulley - Adjustable side strip guides - All straightening rolls driven via distribution gearbox and cardan shafts - Both pinch rolls driven via gearbox with cardan shafts - Frequency-controlled drive via geared motors Isdpfxoif Sg Sj Ag Dea - Straightener opening stroke 250 mm for cleaning or for processing thicker material, lifting by trapezoidal-thread spindle - Ultrasonic loop control Transport dimensions (L x W x H): 3600 x 2200 x 2200 mm Net weight: approx. 4 tons Decoiler HMS Type BA 1.5-06/80, Machine No. Coil weight: max. 8000 kg Outer coil diameter: max. 1600 mm (with load carriage) Outer coil diameter: max. 2000 mm (without load carriage) Diameter of coil turntable: Ø 1700 mm Coil inner diameter, expansion range: 460–520 mm Coil width, nominal: max. 630 mm Expansion jaw width: 750 mm Height of decoiler drum above base plate: 1500 mm - Decoiler drum driven by hydraulic motor and gear - Pneumatic overrun brake on the decoiler drum (TWINFLEX) - Hydraulic expansion of the decoiler drum, centrally via wedge slider system - Hydraulic pressure arm with hydraulically driven double pendulum roller - Coil loading carriage with 12-ton lifting capacity and 300 mm stroke - Decoiler on elevated travel frame with motorized cross travel drive Transport dimensions (L x W x H): 3500 x 1900 x 2500 mm Net weight: approx. 5 tons Central Hydraulic Power Unit (adjacent) Tank capacity: 350 liters Drive power: 18.5 kW - Drive motor with 2x REXROTH tandem pumps - Oil cooler as air heat exchanger with fan motor Transport dimensions (L x W x H): 1600 x 850 x 1450 mm Net weight: approx. 800 kg Electrical Cabinet (adjacent) - All cable connections via Harting connectors Transport dimensions (L x W x H): 2800 x 500 x 2250 mm Net weight: approx. 800 kg

Condition: used, Revolving briquetting press RUF type RBK 55/2500/120 S Hydraulic pellet press or briquetting press for grinding sludge, metal chips, or similar No. 70002 Year of construction 2009 Briquette diameter 120 mm Briquette length in the pre-compactor approx. 120 mm Pressing force in the pre-compactor 30 tons at 260 bar Briquette length in the main compactor approx. 80 mm Pressing force of the main press cylinder 250 tons at 260 bar Stroke size of the main press cylinder 120 mm Pressing force of the counter-press cylinder 250 tons at 260 bar Stroke size of the counterpress cylinder 15 mm Piston diameter of the main press cylinder 350 mm Press stroke Cycle time approx. 30 sec. for grinding sludge with low residual oil content Hopper size of the screw conveyor 1000 x 600 mm Hydraulic motor power 37 kW Mains connection 400 Volt, 50 Hz, 45 kW - Revolver with 5 stations for high material throughput - Pre-compressor stage for pressing material into the turret disk - 2 opposing main press cylinders with 120 mm and 15 mm stroke - Ejection cylinder for ejecting the finished briquettes from the turret disk - Infinitely variable adjustment of the hydraulic speed for each pressing stage - was used for grinding sludge from metal processing - Material hopper as hopper with screw conveyor - the machine was completely overhauled at RUF in 2018 - a new SIEMENS Simatic touch panel was installed in 2020 - only a few operating hours after the overhaul very good condition Grinding sludge recycling Ijdehg Uz Iepfx Ag Dea - great savings through cooling lubricant recovery - Large savings in disposal costs due to the reduction in volume and weight of the grinding sludge - Grinding sludge briquettes with a low residual oil content can possibly be classified as "non-hazardous waste".

Condition: used, Ishida Checkweigher and Metal Detector Fully stainless steel Iodpfxjxtfymo Ag Dja Reject bin Weighing range - 0 to 1200 grams 240 volts

Condition: new, We offer here for sale a new workbench from the manufacturer Metal Sistem. Delivery time: approx. 3 - 4 weeks Technical data of the workbench: Manufacturer: Metal Sistem Type: Super 4/5/6 Workbench width: 1.200 mm Workbench depth: 900 mm Workbench height: 900 mm Included in delivery: 02x workbench stand, new Material color: compl. galvanized type of stand: TS4 incl. cross and diagonal braces, foot plates The stands are pre-assembled (bolted truss) 723 mm high 700 mm deep 04x workbench trusses, new Crosshead type: TS profile dim.: 70 x 42 x 3 mm clear width: 920 mm Material color: compl. galvanized 01x worktop, new Wood type: MDF thickness: 28 mm dimension: 900 x 1.200 mm Material color: black 03x steel shelves, new dimension: 300 x 700 mm Type: H29/D 02x swivel castors, new Iedpfx Agohq Txhs Dja 02x brake/steering rollers, new 01x angle set, new for mounting the worktop 08x safety hook, new Material color: compl. galvanized

Condition: excellent (used), Desktop Metal 3D Printer Complete System Here we offer you Desktop Metal 3D printer complete system. Desktop Metal 3D printer studio system Complete system: 3D printer + debinding machine + sintering furnace Desktop Metal Iedpfxok Hz Nqj Ag Dsa The three-part solution includes 3D printer, debinder and furnace Manufacturer Desktop Metal Model Desktop Metal Studio System Operating condition Used (Good) Year of manufacture 2019 Desktop Metal Studio System Includes: 1.1 Desktop Metal Studio 3D Printer Bound Metal Deposition (BMD) Technology. Features: Printed materials metal Technology FDM Use Industry Other features Office X-stroke 30 cm (12 in) Y-stroke 20 cm (8 in) Z-stroke 20 cm (8 in) Description: Unlike laser-based systems that selectively melt metal powders, the printer extrudes bonded metal rods - similar to an FDM printer. This eliminates the safety requirements often associated with metal 3D printing, and it enables new features such as the use of closed-cell fills for lightweight strengths. 1.2 Desktop Metal Studio debinder (delamination machine) fully automatic debinding Cleaning tank: 17.4 L (in process) / 22.5 L (stock) Description: The debinder prepares green parts for sintering by dissolving the primary binder. With a low emission design, it requires no external ventilation and is safe for an office environment. Automatic liquid distillation and recycling means no need to refill between cycles. 1.3 Desktop Metal Studio Sintering Furnace hybrid technology (microwaves & conventional heating elements) Installation space 305x205x205mm Carbon housing Gas supply: 2 x 900 L gas cylinders Heating power: 20 kW Features: Function Sinter Configuration Chamber Heat source gas Other features High temperature, automatic Maximum temperature 1,400 °C (2,552 °F) Description: Fully automated and sized to fit through an office door, the furnace delivers industrial-grade sintering in an office-friendly package. Built-in temperature profiles matched to each design and material provide uniform heating and cooling without the residual stresses associated with laser-based systems. Condition: used / used Scope of delivery: (see picture) (Changes and errors in the technical data, specifications are reserved!) Further questions we can answer on the phone for you.

Condition: new, functionality: fully functional, Year of construction: 2025, control type: CNC control, actuation type: electric, laser type: fiber laser, laser power: 12,000 W, input voltage: 380 V, input frequency: 50 Hz, warranty duration: 24 months, Equipment: CE marking, centralized greasing system, cooling unit, documentation/manual, dust extraction, emergency stop, fume extraction, nozzle changer, safety light barrier, Equipment model: NS56FG Iodsww Umaepfx Ag Dea Maximum tubelength:

Condition: excellent (used), Machine: Used Lindemann Sobod 8 Metal Baler Bale size: 400mm x 400mm Specifications: see table Status: ready to use Condition: in very good maintenance condition Year of manufacture: unknown Power: electric Iodpfx Agexrz S Aj Dea Availability: March/April 2025

Condition: excellent (used), functionality: fully functional, Year of construction: 2021, operating hours: 250 h, Since 2021 for customer prints, product demonstrations and trade fair appearances in our possession. Completely ready for use and prepared by manufacturer-certified personnel from IGO3D, Desktop Metal Partner. Can be demonstrated in Hanover, Germany (also remotely via video call). Easy-to-use Additive Manufacturing 2.0 solutions for industrial production — delivering transformative value. Office-friendly metal 3D printing with two steps (Print > Sinter) and eight materials. Key benefits: Iedpfx Asm Rgzasg Dja „ Easy, two-step processing „ User-friendly software-controlled workflow „ Patented smart Separable SupportsTM technology for quick post-processing „ Qualified for eight materials „ Designed for office-friendly printing „ A trusted system used worldwide with success The easy-to-use Studio System leverages proprietary Bound Metal Deposition™ (BMD), an extrusion-based metal additive manufacturing process where metal rods — metal powder held together by wax and polymer binder — are heated and extruded onto the build plate, shaping a part layer by layer. Once printed, the binder is removed via the debind process, and then sintered, causing the metal particles to densify. The Studio System 2 is even easier to use than ever before with new material formulations allowing printed parts to be placed directly into the furnace without the need for a solvent debind. The result is a streamlined two-step process with a nearly hands-free experience. Eight materials are available, including a range of steels, copper, and nickel and titanium alloys. Simplified metal part production using safe-to-handle bound metal rods The Desktop Metal Studio system creates metal parts for functional prototypes, tooling, jigs and fixtures, and low-volume production applications with expert metallurgy built-in. Easily produce difficult-to-machine parts featuring complex geometries like undercuts and internal channels to optimize metal components in an office setting.

Condition: good (used), Fortress Phantom Metal Detector Fully stainless steel Aperture 500mm wide x 225mm high 1500mm long Belt Stop and alarm Isdpfx Agoxtfw Ss Dea Video available on request

Condition: new, We offer here for sale a new workbench from the manufacturer Metal Sistem. Delivery time: approx. 3 - 4 weeks Technical data of the workbench: Manufacturer: Metal Sistem Type: Super 4/5/6 Isdpfx Aohq Twyjg Doa Workbench width: 1.200 mm Workbench depth: 900 mm Workbench height: 900 mm Included in delivery: 02x workbench stand, new Material color: compl. galvanized type of stand: TS4 incl. cross and diagonal braces, foot plates The stands are pre-assembled (bolted truss) 888 mm high 700 mm deep 04x workbench trusses, new Crosshead type: TS profile dim.: 70 x 42 x 3 mm clear width: 920 mm Material color: compl. galvanized 01x worktop, new Wood type: MDF thickness: 28 mm dimension: 900 x 1.200 mm Material color: black 03x steel shelves, new dimension: 300 x 700 mm Type: H29/D 01x Angle set, new for fixing the worktop 08x safety hook, new Material color: compl. galvanized

Condition: excellent (used), functionality: fully functional, Year of construction: 2022, For sale is a complete metal 3D printing system from Desktop Metal, suitable for additive manufacturing with metal powders using the binder jetting process. The system is ideal for prototyping, small-scale production, and research. Included in the purchase price: 1x Printer (Desktop Metal, 12-liter volume) 1x Sintering furnace 1x Gas valve for the sintering furnace 1x Drying furnace 2x Depowdering stations 1x Powder mixer 2x Industrial vacuum cleaners 6x Powder drums Not included in the purchase price (can be purchased optionally): 1x Additional drying furnace 1x Depowdering station (in-house development) Ijdpewgky Iofx Ag Dsa 250 kg metal powder 17-4PH 100 kg metal powder 316L Additional powder drums Protective equipment for 2 people Other accessories

Condition: new, functionality: fully functional, Year of construction: 2025, table width: 4,120 mm, working width: 2,530 mm, travel distance Y-axis: 6,020 mm, travel distance Z-axis: 450 mm, type of input current: three-phase, overall weight: 14,200 kg, warranty duration: 24 months, working range: 6,225 mm, Equipment: CE marking, centralized greasing system, cooling unit, documentation/manual, dust extraction, emergency stop, fume extraction, nozzle changer, safety light barrier, All New Full Cover Fiber Laser Cutting Machine | GS-CE PRO Series | 6000-40000W MACHINE AVAILABLE ON HAND This GS-CE series FULL COVER FIBER LASER CUTTING MACHINE offers maximum safety for metals cutting. Thanks to its full cover structure and protective glass observation window, you can observe the operation and avoid hazards such as laser radiation, sparks, etc. It also has a fast exchange table, and the exchange is within 10s. It will be your ideal solution for safe and efficient metal cutting! Working platform size: 3000mm*1500mm, 4000mm*2000mm, 6000mm*2000mm, 6000mm*2500mm;8000mm*2500mm;12000mm*2500mm; Laser power 6KW-40KW GS-6225CE PRO Max. Acceleration：3G Intelligent anti-collision function Automatic lubrication Laser fault alarm Cooling fault alarm Laser protection glass Iodpfxjvzwh No Ag Doa Water cooler TÜV CE certificate Optional function: automatic loading and unloading system Control unit supports graphic formats: AI, BMP, Dst, Dwg, DXF, DXP External programming System complete incl. cooler, extraction system and safety light barriers Demonstration machine as good as new

Condition: used, Year of construction: 2003, LARCON METAL Model: LIJADORA DE RODILLO Number: 29 Iedpfxjxrz Nbj Ag Dsa Year of construction: 2003 kW: 4 RPM: 1500

Condition: used, Rain gutter, downpipe and elbow forming machines, complete line. Three machines. 1. Rain gutter forming machine, strip cutting with band saw. Produced gutter diameter: 80 x 100 mm Used sheet metal dimensions: Width: 350 mm. Thickness: 0.43 – 0.55 mm. 2. Downpipe forming machine, can form 127 mm and 152 mm (standard) sizes. Cutting with guillotine. Used sheet metal dimensions: Width: 300 mm. Thickness: 0.43 – 0.55 mm. Iodpfxev Evcte Ag Dea 3. Elbow forming machine: 400V/3 If you have any further questions, we will be happy to answer them.

Condition: excellent (used), Year of construction: 2016, Loma Systems Metal Detector with Rejector Model: IQ³ Model conveyor: MD Conveyor, serial number: G7B3C2RS-35150D Iodpfxov T Ah Ej Ag Dea Year of construction: 2016 220-240 V, 1 Ph, 50/60 Hz, 3 A Belt width: 300 mm, clearance: 350 mm x 150 mm Total dimensions: 2020 mm x 1080 mm x 1120 mm

Condition: new, We offer here for sale a new workbench from the manufacturer Metal Sistem. Delivery time: approx. 3 - 4 weeks Technical data of the workbench: Manufacturer: Metal Sistem Type: Super 4/5/6 Workbench width: 1.200 mm Isdpfx Agjhq Txwo Dsa Workbench depth: 900 mm Workbench height: 900 mm Included in delivery: 02x workbench stand, new Material color: compl. galvanized type of stand: TS4 incl. cross and diagonal braces, foot plates The stands are pre-assembled (bolted truss) 723 mm high 700 mm deep 02x workbench trusses, new Crosshead type: TS profile dim.: 70 x 42 x 3 mm clear width: 920 mm Material color: compl. galvanized 01x worktop, new Wood type: MDF thickness: 28 mm dimension: 900 x 1.200 mm Material color: black 02x swivel castors, new 02x brake / swivel castors, new 01x angle set, new for mounting the worktop 04x safety hook, new Material color: compl. galvanized

Condition: ready for operation (used), functionality: fully functional, machine/vehicle number: SP0119240003037, Year of construction: 2019, input voltage: 240 V, Equipment: CE marking, Bound Metal Deposition™ metal 3D printing system composed of: - printer - debinder - sintering furnace - frequency converter for 60Hz furnace power supply. System in perfect condition, used for R&D in a climate-controlled environment. Printer equipped with 2 nozzles (0.40mm diameter) and one high-definition nozzle (0.25mm diameter). Furnace equipped with a technical gas supply system from an external installation. Set of original replacement parts for furnace (ceramic setters, graphite retort shelves, gaskets, filters, vacuum pump oil). Firmware updated to the latest release throughout the system. Material cartridges included: Ijdpfx Aexlcldog Dja 1x AISI 316L 1x 17-4PH 1x ceramic support

Condition: new, functionality: fully functional, Year of construction: 2025, laser power: 30,000 W, travel distance X-axis: 3,050 mm, travel distance Y-axis: 13,050 mm, travel distance Z-axis: 450 mm, positioning accuracy: 0.03 mm, repeat accuracy: 0.02 mm, workpiece weight (max.): 20,000 kg, input frequency: 50 Hz, total length: 16,800 mm, total width: 2,200 mm, total height: 5,120 mm, warranty duration: 24 months, working range: 13,000 mm, Equipment: CE marking, centralized greasing system, cooling unit, documentation/manual, dust extraction, emergency stop, fume extraction, safety light barrier, GS-CL Series, Glorystar Single Table Gantry Type Metal Laser Cutting Machine Laser Power: 12000-80000W Fits in a standard 40HQ container The GS-L Series is a high-power metal laser cutting machine with a gantry-type segmented bed design. It can be freely customized to meet processing format requirements according to customer needs. Key Features: ● Super Large Processing Format with a gantry-style segmented design. ● The GS-L Series has the largest Z-axis travel and height in its class in the industry. Supports extreme thickness cutting for plates over 20mm. Capable of cutting ultra-thick plates up to 70mm. ● High Negative Pressure Automatic Partition Dust Removal ● Equipped with a high-air-volume fan for effective dust removal. Technical parameters: Working area (mm): 13000mm*3000mm（bevel cut: 12500mm*2500mm） X axis travel distance (mm): 3050mm Y axis travel distance (mm): 13050mm Iedpfsvmwn Hex Ag Dea Z axis travel distance (mm): 450mm X/Y axis positioning accuracy: ≤0.03mm/m X/Y axis repeat positioning accuracy: ≤±0.02mm Max. synthetic positioning speed: 110m/min Max. acceleration: 1.2G Min. setting unit: 0.001mm Floor size (mm): 18500mm*6500mm Main body dimension (mm): 16800mm*5120mm*2200mm Worktable max. weight capacity (T): 20 tons (even load bearing)

Condition: used, Pneumatic cylinder, air cylinder, pneumatic stamp, compact cylinder -Manufacturer: Metal Work, compact cylinder tray sealing machine Inauen VC999/ TS 1200 N -Type: 121AA20160ZP -Stroke: 160mm -Piston: Ø 120 mm -Piston rod: Ø 32 mm / M27 x 2 Ijdpfx Aom Hd Rzog Doa -Dimensions: 445/135/H135 mm -Weight: 9.6kg

Condition: excellent (used), Year of construction: 2012, Lock met 30+ Throat / Vertical Fall Metal Detector The MET 30+ UNIVERSAL compact vertical fall system can be installed at the beginning of the Ijdpfx Aeu Dntljg Dea production line to inspect materials in bulk powder or granule form or anywhere for free falling products. • Detects real-life contaminants • ATEX zone 21 approved • Throughput up to 50 tonnes per hour • Quick release sealed valve or cowbell reject mechanisms available • Sealed to IP 66 for washdown applications

Condition: new, We offer here for sale a new workbench from the manufacturer Metal Sistem. Delivery time: approx. 3 - 4 weeks Technical data of the workbench: Manufacturer: Metal Sistem Type: Super 4/5/6 Workbench width: 1.200 mm Workbench depth: 900 mm Workbench height: 900 mm Included in delivery: 02x workbench stand, new Material color: compl. galvanized type of stand: TS4 incl. cross and diagonal braces, foot plates The stands are pre-assembled (bolted truss) 888 mm high 700 mm deep 02x workbench trusses, new Crosshead type: TS profile dim.: 70 x 42 x 3 mm clear width: 920 mm Material color: compl. galvanized 01x worktop, new Wood type: MDF Iodpfxehq Tqdj Ag Dja thickness: 28 mm dimension: 900 x 1.200 mm Material color: black 01x angle set, new for fixing the worktop 04x safety hook, new Material color: compl. galvanized

Condition: excellent (used), Year of construction: 2020, Elektron Metal Detector Aperture 180mm Wide x 405mm High Belt length 1500mm Long Stainless Steel Two run features options - alarm and stop or air reject blast Reject bin Isdpjvw D Iuofx Ag Doa In excellent condition

Condition: good (used), Technical data for pallet rack beam: Racking system: Metall Sistem Iodpexb Tp Ejfx Ag Dsa Type: Unipal Scope of delivery includes: 01x pallet rack beam, used Material color: yellow Box profile: 140 x 45 mm Clear width: 1,800 mm Your contacts in our company: Mr. Andre Evering Mr. Mario Klöver Mr. Falk Deutsch General information about the item: This item is offered for collection only. Any additional transport or shipment of this item will incur extra costs, which can be quoted separately depending on the place of delivery or scope of delivery.