Used Fasti for sale (84)

Condition: used, Max. cutting length: 2540 mm Max. sheet thickness: 6 mm steel Mechanically adjustable rear stop (2 speeds) up to 1000 mm with analog display Side stops and table extensions Laodszl Dr Sspfx Apmjd cutting length limitation Cutting edge lighting knife sharpened Weight approx. 5500 kg

Condition: used, Max. bending length: 1020 mm Max. sheet thickness: 6 mm steel Upper wheel diameter: 150 mm Motorized rear roller delivery Right and left rotation via foot switch Safety rope pull switch Conical rounding possible Laedpszl Dngofx Apmed Weight: 1200 kg

Condition: good (used), Press brake FASTI, bending length 250 cm, serial number 99527004, model size 527-25-3.25, own weight 3,200 kg. Lsdpfxsznl A Rj Apmsad

Year of construction: 2000, condition: ready for operation (used), overall weight: 2,110 kg, sheet thickness (max.): 5 mm, working length: 2,040 mm, Plate rolling machine manufactured in 2000. This FASTI 136-20-4.5 features a capacity of 2040 x 4.5 mm at 400 N/mm² tensile strength and weighs 2110 kg. It is equipped with a Fasti-Matik 5 R control unit and operates at 400 V. If you are looking to get high-quality plate rolling capabilities, consider the FASTI 136-20-4.5 machine we have for sale. Contact us for further details. Lsdpezi S U Aefx Apmjad - Capacity: 2040 x 4.5 mm (at 400 N/mm² Tensile Strength)- Weight: 2110 kg- Control Unit Model: Fasti-Matik 5 R (FM 5 / FM 5 R)- Operating Voltage: 400 V (3/N/PE~)- Frequency: 50 Hz- Control Voltage: 230 V AC / 24 V DC / 24 V AC- Connected Load: 6.356 kW- Nominal Current: 15.7 A- Circuit Diagram No.: 10X0001 B- Included Equipment: Control unit operating manual, machine instruction handbook- Working Hours: estimated as very low- Saving programs to the 3.5-inch floppy drive does not work (no access). It may be possible to replace it, though or the values must be entered manually.

Condition: good (used), functionality: fully functional, Year of construction: 1985, Swivel bending machine Manufacturer: FASTI Type: 212 50/3 Year of manufacture: 1984 Control system: FASTIMATIK Max. bending length: 5040 mm Max. sheet thickness: 3 mm Smallest inner radius: 4.5 mm Smallest internal flange height: 24 Opening angle: 350 mm Stroke speed: 16 mm/s Drive: mechanical Lower die: fixed Height above floor: 900 mm Adjustable bending die: 80 mm Swivel angle: 180 degrees Rear stop: 6 - 2000 mm Ljdpfx Apszmnacsmjad Dimensions: 6250 x 4000 mm, height 1940 mm Weight: 12,700 kg

Condition: like new (used), Year of construction: 2023, operating hours: 1 h, actuation type: manual, working width: 2,030 mm, back gauge: 750 mm, Equipment: documentation/manual, type plate available, Panel shear, like new, unused. The machine was delivered by Schröder in January 2023 and put into operation. Since it was unsuitable for the intended application (see photos), it was subsequently stored and is in absolutely new condition. The new price was €12,381 (excluding transport + assembly). Manufacturer: SCHRÖDER Lodpfx Apozl A Rajmsad Type: HS 2000 x 1.25 Year of manufacture: 2023 Usable length: 2,030 mm Cutting capacity at 400 N/mm2: 1.25 mm Equipment: - Rear stop 750 mm, digital display, adjustable at the front - Hold-down device 750 mm - Stainless steel blade - Clamping beam with hard rubber strip - Front support table, extendable - Angle stop right + left - Sliding carriage

Condition: good (used), Punching machine, punching device, hole punching machine, multi-head punch, multi-head punch, punching system -Quantity: 5x punches -Max. width: 1000 mm -Tool built-in: 8x45 mm -Distance between punches: 187 mm -powered: electric -Weight: 280 kg Lasdpfx Asb A I Ibepmod

Condition: good (used), electric clutch, electromagnetic clutch for guillotine shear, sheet metal shear, sheet metal guillotine shear, crank guillotine shear, eccentric press -for: Crank-operated guillotine shears -Equipment: Coupling, transformer, control unit -Manufacturer: LABOD electronic -Type: GN 6 DZ.4Q.80 Lsdpfx Apjb A I Uijmsad -Total net weight: 160 kg

Condition: good (used), Punching machine, punching device, hole punching machine, multi-head punch, multi-head punch, punching system -Division: 8 x punch pairs with a spacing of 60 mm (Ø 4 mm) -Distance between the two outer pairs of punches: 975 mm -Spacing: 75 - 165 - 165 - 165 - 165 - 165 - 165 - 75 mm -Max. passage width: 1000 mm -Drive: electric Laedpfxjb A I I Te Apmjd -Weight: 260 kg

Condition: excellent (used), Three-roll bending machine, three-roll sheet metal bending machine, bending machine, sheet metal bending machine, 3-roll bending machine, profile bending machine, three-roll sheet metal rolling machine, manual bending machine Laodpjywzlpjfx Apmjd -Roll bending machine: 3-roll roll bending machine, electrically driven -Bending adjustment: electric -Max. sheet width: 2040 mm -Max. sheet thickness: 4 mm -Roller diameter: 150 mm -Dimensions: 1080/2880/H1370 mm -Weight: 1770 kg

Condition: ready for operation (used), functionality: fully functional, Year of construction: 2020, control type: CNC control, working width: 3,000 mm, sheet thickness (max.): 6 mm, overall weight: 6,500 kg, Hydraulic plate shear Manufacturer: Schrödergroup, Type: Powershear – 3000 x 6mm Year of manufacture: 2020 Technical data Manufacturer: Schröder Type: 530 - 30/6 Year of manufacture: 2020 Sheet width: 3040 mm Sheet thickness: 6.00 mm (400N/mm) Shear gap adjustment: 0.5 – 1.8 mm Stroke rate: 24-61 strokes/min Drive power: 12.0 kW Space requirement (L x W x H): approx. L 4.00 x 3.00 x 1.96 m Weight: approx. 6.5 t Equipment - 12" touchscreen control PSC 150 on a swiveling panel - energy-efficient drive for frequency-controlled motor and pump - automatic shear gap adjustment - Adjustable clamping pressure, pre-selectable via the control unit - motorized back gauge 10-1000 mm on ball screw spindles - pneumatic sheet metal holding device - LED cutting edge lighting - programmable start and end position of the blade beam - angle stop mounted on the left, incl. electronic length measuring system, fine adjustment and side folding stop on linear guide 1000 mm - 2 stop arms with ball rollers, movable on a linear guide - table support made of stainless steel sheets, incl. ball rollers - protection of the rear side with a light curtain - scrap and small parts chute to the front, incl. "Return to Sender" function Lsdpezi Ezvsfx Apmsad - movable table extension mounted on a guide rail - finger guard, retractable to approx. 1500 mm, incl. electrical protection All information without guarantee. A demonstration is possible at any time in our showroom.

Condition: used, Year of construction: 1983, sheet width 2540 mm plate thickness 2 mm distance between columns 2600 mm min. cut-off length 5 x s mm adjustment of lower beam 80 mm adjustment of upper beam 80 mm Ljdsw H Dkaspfx Apmead daylight opening 350 mm total power requirement 4 kW dimensions 4 x 1 x 1,5 m With accessories.

Condition: used, Year of construction: 1961, sheet width 1020 mm plate thickness 2 mm Lsdpezfax Ijfx Apmoad

Condition: used, Year of construction: 2002, Max. Schnittlänge: 1270 mm Max. Cutting thickness: 4 mm steel Manual rear end stop with hand crank Cutting gap adjustment by handwheel Side stop and table extensions Ledpfezfkmpox Apmjad Weight: approx. 2000 kg

Condition: new, sheet width 1000 mm plate thickness 1,0 mm distance between columns 1030 mm daylight opening 80 mm Lajdpfxezhn Uio Apmjd 135 ° total power requirement Handbetrieben weight of the machine ca. 0,15 t dimensions of the machine ca. 1,3 x 0,8 x 1,2 m

Condition: used, Fasti 417 Beading and Flanging Machine with motorized drive and hydraulic adjustment of the upper roll Condition: Used Technical data Type 125/3 Capacity: 3.0 mm Roller center distance: 125 mm Throat depth: 500 mm Working depth: 430 mm Drive 2 (standard): 1.5/2.5 kW Drive 3: 3.0 kW Hydraulic drive: 0.75 kW Details Without rolls Without back gauge Gear motor with pole-changing capability V06/12 m/min. Lasdjyxdl Ispfx Apmed

Condition: used, functionality: fully functional, Year of construction: 1989, machine/vehicle number: 204-10-2, Sales only within EU member states! Laodpfxszibtnj Apmsd No private sales. Any warranty is excluded. We assume no liability for the accuracy of the technical data and year of manufacture, for the completeness of accessories and tool equipment, or for compliance with all safety and environmental protection requirements mentioned in the accident prevention regulations.

Condition: used, Year of construction: 1993, plate thickness max. 3 mm distance betw. rolls 125 mm throat max. 500 mm weight ca. 500 kg Material thickness at 40 kg/mm² tensile strength: max. 3 mm Working width: 500 mm Working depth: 450 mm Manual adjustment of the upper roller Roller center distance: 125 mm Ledpfx Apoy Iha Usmoad Continuously variable working speed: 3–15 m/min Stop skirt incl. 1 pair of rolls Forward/reverse operation via foot switch

Condition: good (used), motorized limit stop behind foot switch Technische Daten / technical details: Schnittleistung (Blechdicke) / max. cutting capacity (thickness of sheet) 6 mm Schnittlänge / max. cutting length 2035 mm Hinteranschlag / arrester behind 1000 mm Laedpfx Aohtq N Njpmed Ständerweite / distance between columns 2000 Mm Antriebsleistung / drive capacity 11 kW Gewicht der Maschine / weight 3500 kg Technische Daten, Zubehör und Beschreibung der Maschine sind unverbindlich - Technical data, accessories and description of the machine are not binding.

Condition: like new (used), FASTI Type 63x1.5 Beading Machine / Like new, almost unused -CE marking -Upper beading roller, hydraulically adjustable -Control panel Ljdpfxoziviko Apmoad -Various beading tools -Hydraulic unit -Documentation Dimensions: L x W x H / Weight 1200 kg Errors and omissions excepted.

Condition: good (used), Year of construction: 2001, sheet width 2520 mm plate thickness 3.0 mm 350 mm Swing beam adjustment 80.0 mm back stop - adjustable ca. 1.000 mm Control FM 5.1 B upper clamping bar adjustment 20.0 mm/sek bending speed 37.0 Grad/sek total power requirement 4.5 kW weight ca. 3.250 kg The ideal solution for individual and series production. A modern design with particularly high rigidity. Designed for continuous performance. Features: - Dynamic, powerful electro-motorized folding machine * Upper beam bending beam drive by geared brake motor * Bending beam drive with roller bearings - FASTI CNC control "TOUCH" - FM 5.1 B * Swiveling control unit, front right * 11.3" color LCD touch screen display * Manual / automatic mode selectable * Input of actual/target values possible (X axis / angle etc.) * Program memory * Tool memory - CNC electro-motorized back gauge * with rear sheet support surface - CNC electro-motorized folding beam adjustment Lajdpfx Apjy Umd Sjmed - 1x extra set of FASTI split scribing tools - height : 120 mm - EMERGENCY OFF button at the front, with extension cable - 1x free-moving double foot switch - 1x free-moving foot switch - original operating instructions - Smallest bending leg length in mm to sheet thickness : * 7.0 mm with 0.75 mm sheet thickness * 8.5 mm for 1.00 mm sheet thickness * 12.0 mm for 1.50 mm sheet thickness * 16.0 mm for 2.00 mm sheet thickness * 19.5 mm for 2.50 mm sheet thickness * 25.0 mm for 3.00 mm sheet thickness

Condition: good (used), Year of construction: 1991, machine/vehicle number: 91212035, Offer 26016 Technical data: - max. working width 2040 mm - max. material thickness at 40 kg/mm² tensile strength 4 mm Lodpfxezgu Tie Apmead - bending angle adjustable electronically, preselectable 0 - 135° - automatic sequential control for a complete working process - largest opening width / stroke of the upper beam 350 mm - height adjustment: - of the upper beam 100 mm - of the lower beam 100 mm - upper beam drive 400 V / 4 kW - bending beam drive 400 V / 4 kW - accessories: - motorized bending beam adjustment - rear stop adjustable with handwheel - electric foot pedal - space requirement with rear stop: - approx. W 3200 x H 1650 x D 2100 mm - weight approx. 4500 kg

Condition: ready for operation (used), Year of construction: 1993, control type: NC control, working width: 2,040 mm, sheet thickness steel (max.): 6 mm, overall weight: 6,000 kg, total length: 2,800 mm, total width: 3,400 mm, total height: 2,100 mm, Hydraulic swiveling bending machine Manufacturer: FASTI, Type: 212 – 20 – 6 Year of manufacture: Dec. 1993 / Jan. 1994 Technical data Manufacturer: Fasti Type: 212-20-6 Year of manufacture: Dec. 1993 / Jan. 1994 Working length: 2040 mm Sheet thickness: 6 mm Stroke: 300 mm Connected power: 12.42 kW Voltage: 400 V Number of phases: 3 Control voltage: 230 V AC // 24 V DC Rated current: 16.5 A Mains frequency [Hz]: 50 Installation dimensions: L 3.35 x W 2.80 x H 2.10 m Weight: approx. 6 t Equipment - Bending angle adjustment using a potentiometer and digital display - Sheet thickness adjustment (bending flange) using a button and digital display - Controlled back gauge (1000/1500 mm) with ball bearings Lajdpfxeza D Eis Apmjd - Sharp edge guide - Bending guide All information is subject to change without notice. The machine is particularly distinguished by its very simple operation. A demonstration is possible at any time in our showroom.

Condition: excellent (used), Bending length: 1020 mm Bending capacity: 2 mm Stroke of the upper beam: 220 mm Adjustability of the lower and bending beams: 60 mm each Lsdpozh Ey Njfx Apmoad Total weight: approx. 0.5 tons Equipment: - Finger stop scale, pinion and rack, adjustment range from 0 – 600 mm - Weight compensation for the bending beam

Condition: good (used), functionality: fully functional, RAS: Cutting length 1040 mm Sheet thickness in carbon steel 2.5 mm Sheet thickness in stainless steel (700 N) 1.5 mm Rear stop up to 550 mm .....FASTI: 1020 x 2 mm Laedpozhka Ujfx Apmod