Used Haas Vf 2 Ss for sale (225)

Condition: good (used), Year of construction: 2006, functionality: fully functional, Machine parameters: Swing over bed: 406 mm Max. turning length: 1219 mm Description: Lhodpfx Aboz S Hy Royon The machine is in good technical condition, and a test run is possible upon prior agreement. Haas CNC control. Max. turning diameter 406 mm / 16". Max. turning length 1,219 mm / 48". Distance between centers 1,219 mm / 48". Swing over cross slide / carriage approx. 282 mm / 11.1". X-axis travel 203 mm / 8". Z-axis travel 1,219 mm / 48". Spindle A2-6. Spindle bore 76.2 mm / 3.00". Spindle speed 0–2,000 rpm. Spindle power 12 HP / approx. 8.9 kW. Torque approx. 203 Nm at 150 rpm. Chuck usually 10" / 254 mm. Tailstock manual, depending on configuration. Weight approx. 2,087 kg. Machine dimensions approx. 2,515 × 1,727 × 1,981 mm (operating dimensions). Electrical connection 195–260 V, 3-phase / approx. 25 A or 1-phase 240 V / 40 A depending on configuration.

Condition: good (used), Year of construction: 2005, functionality: fully functional, Description: Ljdpjz S H Afofx Abyehn The machine is in good technical condition, and can be tested upon prior arrangement. It features a Haas CNC control system, often a 32-bit version for this model year. Travel distances for X/Y/Z axes are 1016 × 406 × 406 mm, or 40" × 16" × 16" in inches. Table dimensions are 1467 × 267 mm / 57.75" × 10.5". Spindle taper is CAT/CT 40 or BT 40. Spindle speed ranges from 0–4000 rpm. Spindle power is 5.6 kW / 7.5 HP. The spindle drive is belt-driven. Maximum torque is approximately 45 Nm at 1200 rpm. Distance from the spindle nose to the table is 102–508 mm / 4"–20". Rapid traverse rates for X/Y/Z axes are 5.1 m/min / 200 ipm. Maximum cutting feed rate is 5.1 m/min. There are 3 T-slots, each approximately 16 mm wide.

Condition: ready for operation (used), Year of construction: 2013, operating hours: 2,995 h, travel distance X-axis: 1,016 mm, travel distance Y-axis: 406 mm, travel distance Z-axis: 406 mm, controller manufacturer: HAAS, table width: 267 mm, table length: 1,467 mm, table load: 159 kg, overall weight: 2,295 kg, spindle speed (max.): 6,000 rpm, spindle motor power: 5,600 W, number of slots in tool magazine: 10, number of axes: 3, This 3-axis HAAS HAAS TM-2P was manufactured in 2013. It features an X-axis travel of 1016 mm, Y-axis travel of 406 mm, and Z-axis travel of 406 mm. The machine includes a table size of 1467 x 267 mm and a maximum table load of 159 kg. If you are looking to get high-quality machining capabilities, consider the HAAS HAAS TM-2P vertical machining centre we have for sale. Contact us for further details. • Max tool diameter: 89 mm • Positioning accuracy: 0.01 mm • Repeatability: 0.01 mm • Air pressure: 6.9 bar • Air consumption: 113 l/min • Power supply: 3 × 400 V, 50 Hz Technical Specification Ljdpfx Aozcnzmjbyehn Taper Size ISO 40

Condition: good (used), Year of construction: 2008, HAAS VF-5D / 40 MACHINING CENTER TRAVELS : X : 1,270 mm Y : 660 mm Z : 635 mm DISTANCE BETWEEN PLANE – TABLE AND SPINDLE NOSE : 178 – 813 mm TABLE : DIMENSIONS : 1,321 x 584 mm LOAD CAPACITY : 1,815 mm NUMBER AND SIZE X PITCH OF T-SLOTTS : 7.14 X 80 mm SPINDLE : ROTATIONAL SPEED : 8,000 RPM SPEED RANGES : 2 SPINDLE NOSE : ISO 40 HIGH PRESSURE / INTERNAL COOLANT FEEDS : RAPID SPEED : 18,000 mm / min. WORKING SPEED : 12,700 mm / min. JOG : 0 – 1,260 mm / min. Lodpfjvf Nw Dox Abyshn TOOL MAGAZINE : 24 POSITIONS POWER : 15 KW WEIGHT : KG. 7,000 YEAR OF FIRST INSTALLATION : 2008

Condition: used, Year of construction: 2018, Technical details: x-travel: 711 mm y-travel: 406 mm z-travel: 394 mm distance spindle nose and table: 546 - 152 mm table-size: 864 x 381 mm table load: 226 kg turning speeds: 15000 1/min power capacity: 11,2 kW max. torque on the spindle: 62 Nm spindle taper: SK 40 Lhsdpfx Abszxz Hgjyen Tool changer: 18+1 rapid travel x/y/z: 61 m/min feed: 30,5 m/min max. tool weight: 5,4 kg max. tool length: 178 mm diameter of tools max.: 64 mm Tool change time tool/tool, milling spindle: 1,75 s internal coolant system feed: 21 bar weight of the machine ca.: 2427 kg dimensions of the machine ca.: 2,8 x 2,4 m Vertical 3-axis machining center POS mill 1100, from year 2009 in good condition. Accessories: - Chip conveyor Knoll - additional coolant filtersystem - Programmable coolan jet - automatic Coolant refillsystem - Airpressure through tool - Measuring probe system WIPS - Synchronized treading - Haas Connect remote control - Media Display - Cooling of electrical cabinet - fixtures and tools will not be sold. *

Condition: ready for operation (used), Year of construction: 2016, travel distance X-axis: 1,270 mm, travel distance Y-axis: 660 mm, travel distance Z-axis: 635 mm, spindle speed (max.): 12,000 rpm, spindle motor power: 22,400 W, number of axes: 3, This 3-axis HAAS VF-5SS was manufactured in 2016. It features an X-axis travel of 1270 mm, Y-axis travel of 660 mm, and Z-axis travel of 635 mm. The machine is equipped with a spindle speed of 12,000 rpm and a 24-position tool magazine. If you are looking to get high-quality machining capabilities, consider the HAAS VF-5SS vertical machining centre we have for sale. Contact us for further details. Lsdpfjypb A Dsx Abyshn • T-slots: 7 • Max spindle torque: 122 Nm @ 2000 rpm • Rapid feed: 30 m/min • Tool magazine: 24 positions Technical Specification Taper Size ISO 40

Condition: used, Year of construction: 2008, travel distance X-axis: 1,016 mm, travel distance Y-axis: 660 mm, travel distance Z-axis: 635 mm, number of slots in tool magazine: 30, Equipment: chip conveyor, Used Haas VF3YT/50 CNC milling machine. Ideal for precision machining of metals and other materials. Year of manufacture: 2008 Specifications: Axis travel: X-1016mm, Y-660mm, Z-635mm Table: 1372mm x 610mm Rapid traverse rate: 18 m/min Table load: 1814 kg Spindle taper: SK50 Spindle speed: 7500 rpm Spindle gearbox: 2-speed Spindle power: 22.4 kW Number of tools in the magazine: 30 pcs Machine weight: 7.5 t Dimensions: L x W x H 3.5 x 2.4 x 2.9 m The machine is equipped with: - Renishaw OMP40 workpiece probe - TSC internal spindle cooling - Automatic chip conveyor - Programmable coolant nozzle Lhedpfx Abezwhlgoysn - Side tool magazine - Rigid tapping - Macro - HSM high-speed machining option - Increased memory up to 16MB It is possible to equip the milling machine with a 4th-axis rotary table. The machine has been serviced, is in good working order and ready for operation. The milling machine can be inspected and tested at our company's premises. If you have any questions or require additional information, please send a message or contact us by phone.

Condition: ready for operation (used), Year of construction: 2023, travel distance X-axis: 1,270 mm, travel distance Y-axis: 508 mm, travel distance Z-axis: 635 mm, controller manufacturer: HAAS, table load: 794 kg, overall weight: 6,260 kg, spindle speed (max.): 12,000 rpm, spindle motor power: 22,400 W, number of axes: 3, This 3-axis HAAS VF-4SS was manufactured in 2023. It features an impressive X-axis travel of 1,270 mm, Y-axis travel of 508 mm, and Z-axis travel of 635 mm. The machine includes a robust table size of 1,321 x 495 mm and a maximum table load of 794 kg. If you are looking to get high-quality machining capabilities, consider the HAAS VF-4SS vertical machining centre we have for sale. Contact us for further details. • Condition: Like new, used • Functionality: Fully operational • Operating hours: 3,363 h • Spindle/machining hours: 2,402 hTravels • Spindle nose to table: 107–742 mmSpindle • Maximum spindle torque: 122 Nm at 2,000 rpm • Spindle drive: Inline direct drive • Spindle taper: CAT40 • Number of spindles: 1Table • Table dimensions: 1,321 × 495 mm • Number of T-slots: 5 • T-slot width: 15.9–16 mmTool changer • Tool capacity: 30+1 positions • Tool-to-tool time: approx. 1.8 s • Chip-to-chip time: approx. 2.4 sMachine dimensions and weight • Note: Dimensions in the original ad were incorrectly stated in millimetres instead of centimetres. • Export shipping dimensions without conveyor: 3,330 × 2,330 × 2,570 mm • Export shipping dimensions with chip conveyor: approx. 4,140 × 2,330 × 2,570 mm • Advertised machine weight: approx. 6,200 kg • Official weight with conveyor: approx. 6,260 kgInstalled options • Through-Spindle Coolant (TSC), 300 psi / 21 bar • Renishaw Wireless Intuitive Probing System (WIPS) • High-Speed Machining (HSM) • Programmable coolant nozzleElectrical • 400 V, three-phase power supply Additional equipment • Chip auger • Haas Chip Lift (chip conveyor) • Coolant mist condenser • Probe riser block Lsdpfxjzwffke Abyehn • Approximately 15 tool holders • Documentation and manuals

Condition: ready for operation (used), Year of construction: 2022, operating hours: 1,936 h, travel distance X-axis: 3,048 mm, travel distance Y-axis: 813 mm, travel distance Z-axis: 762 mm, overall weight: 14,334 kg, spindle speed (max.): 7,500 rpm, spindle motor power: 22,400 W, number of axes: 4, This 4-axis HAAS VF-10/50 was manufactured in 2022. It features an impressive X-axis travel of 3048 mm, Y-axis travel of 813 mm, and Z-axis travel of 762 mm. The machine includes a robust table size of 3048 x 711 mm and a maximum table load of 1814 kg. If you are looking to get high-quality machining capabilities, consider the HAAS VF-10/50 vertical machining centre we have for sale. Contact us for further details. • Spindle nose to table (max): 35.0 in (889 mm) • Spindle nose to table (min): 5.0 in (127 mm) • Spindle • Max torque: 340 ft‑lbf @ 700 rpm (460 Nm @ 700 rpm) • Drive system: 2‑speed gearbox • Bearing lubrication: Air/oil injection • Cooling: Liquid cooled • Table • Length: 120.0 in (3048 mm) • Width: 28.0 in (711 mm) • T‑slot width: 0.626–0.630 in (15.90–16.00 mm) • T‑slot center distance: 4.92 in (125 mm) • Number of T‑slots: 5 • Max table load (evenly distributed): 4000 lb (1814 kg) • Feedrates • Max cutting feed: 360 ipm (9.1 m/min) • Rapids: X 360 ipm (9.1 m/min), Y 600 ipm (15.2 m/min), Z 600 ipm (15.2 m/min) • Axis motors (max thrust) • X: 3400 lbf (15,124 N) • Y: 4100 lbf (18,238 N) • Z: 5600 lbf (24,910 N) • Tool changer • Type: SMTC • Capacity: 30+1 • Max tool diameter (all pockets full): 4.0 in (102 mm) • Max tool diameter (adjacent pocket empty): 10.0 in (254 mm) • Max tool length (from gage line): 16 in (406 mm) Lhsdpozh Hlaefx Abyjn • Max tool weight: 30 lb (13.6 kg) • Tool‑to‑tool (avg): 4.2 s • Chip‑to‑chip (avg): 6.3 s • General • Coolant capacity: 95 gal (360 L) • Air requirements • Air required: 4 scfm @ 100 psi (113 L/min @ 6.9 bar) • Inline air hose: 3/8 in • Coupler (air): 3/8 in • Minimum air pressure: 80 psi (5.5 bar) • Electrical • Drive system: 2‑speed gearbox • Input AC voltage (3‑phase) low: 220 VAC, 70 A (FLA) • Input AC voltage (3‑phase) high: 440 VAC, 35 A (FLA) • Dimensions – shipping • Domestic pallet: 288 in x 102 in x 132 in (732 cm x 260 cm x 336 cm) • Export crate: 288 in x 105 in x 134 in (732 cm x 267 cm x 339 cm) • Domestic pallet with EC option: 288 in x 102 in x 140 in (732 cm x 260 cm x 356 cm) • Export crate with EC option: 288 in x 105 in x 141 in (732 cm x 267 cm x 359 cm)

Condition: excellent (used), Year of construction: 2001, Haas VF 6/40 TRHE 5-axis machining center Ljdjzwultepfx Abyohn Year of manufacture: 2001 X-axis: 1,626 mm Y-axis: 813 mm Z-axis: 762 mm A-axis (table tilting): ±120° B-axis (rotation): 360° Rapid traverse: 15,240 mm/min Feed rate during cutting: 12,700 mm/min Distance from spindle nose to table (min.–max.): 102–864 mm Distance from spindle nose to clamping plate (min.–max.): 279–483 mm Tool changer: 24-position Rotary table: Diameter of clamping plate: 310 mm Max. weight on the clamping plate: 227 kg Chip conveyor Handwheel Internal coolant system High-speed machining Quick code Extended memory 16MB Macro Rigid tapping

Condition: ready for operation (used), Year of construction: 2022, spindle speed (max.): 4,000 rpm, travel distance X-axis: 213 mm, travel distance Z-axis: 572 mm, spindle motor power: 14,900 W, overall weight: 4,000 kg, controller manufacturer: HAAS, number of slots in tool magazine: 12, number of axes: 2, Horizontal turning machine manufactured in 2022. This HAAS ST-20 features a maximum cutting diameter of 13.00 in and a maximum cutting length of 22.5 in. It includes a robust spindle power rating of 20.0 hp and a rapid rate of 945 ipm for both axes. If you are looking to get high-quality turning capabilities, consider the HAAS ST-20 machine we have for sale. Contact us for further details. • Chuck size: 8.3 in / 210 mm • Max part swing: 21.0 in / 533 mm • Max cutting diameter (BOT turret): 13.00 in / 330 mm • Max cutting diameter (BMT65 turret): 11.75 in / 298 mm • Max cutting length: 22.5 in / 572 mm Lhedpjz Ha Upsfx Abysn • Bar capacity: 2.50 in / 64 mm • X-axis rapid rate: 945 ipm / 24.0 m/min • Z-axis rapid rate: 945 ipm / 24.0 m/min • X-axis max thrust: 4,100 lbf / 18,238 N • Z-axis max thrust: 5,100 lbf / 22,686 N • Spindle nose: A2-6 • Spindle drive system: Direct speed, belt drive • Spindle max torque: 150.0 ft-lbf @ 500 rpm / 203.0 Nm @ 500 rpm • Spindle bore: 3.50 in / 88.9 mm • Turret stations: 12 stations (VDI 40) • Boring bar rear clearance: 4.00 in / 102.0 mm • Coolant tank capacity: 55 gal / 208 L • Coolant pump: 1 HP / 0.75 kW variable-flow (45 L/min @ 2 bar) • Air requirement: 4 scfm @ 100 psi / 113 L/min @ 6.9 bar • Air pressure minimum: 80 psi / 5.5 bar • Air line / coupler size: 3/8 in • Low voltage electrical: 220 VAC (3 phase), 40 A full load • High voltage electrical: 440 VAC (3 phase), 20 A full load (internal non-isolated transformer 380–480V included) • Shipping dimensions: 143 in x 90 in x 92 in / 362 cm x 229 cm x 234 cm • Control system: Haas NextGen Control with touchscreen interface, 1 GB memory, Ethernet, Wi‑Fi, HaasConnect Remote Monitoring, and Haas Drop • Included machine features/options: Automatic Tool Presetter; Programmable Hydraulic Tailstock (MT4); Rigid Tapping; M130 Media Display; Safe Run; Power Failure Detection Module; Visual Part Programming System Additional equipment • Belt-type chip conveyor • Chip strainer filter kit (200 micron) Technical Specification Taper Size VDI 40 Counter Spindle No Driven Tools No

Year of construction: 1997, condition: excellent (used), functionality: fully functional, machine/vehicle number: 13137, Capacity: approx. 50-56 kg/h (depending on the dough, filling, etc.) Overhaul year: 2026 – new electronics, housings, insulation, gas reducer, all bearings + motors are new or refurbished. Model: EWB 2/2 Two dough belts. Set including a dough tank and pumps – stepless speed control via a frequency inverter. Lhodpfx Aezwmz Hsbyon Power source: CNG/LPG 50 Hz, power: 5.3 kW

Condition: ready for operation (used), Year of construction: 2019, travel distance X-axis: 1,016 mm, travel distance Y-axis: 660 mm, travel distance Z-axis: 635 mm, controller manufacturer: HAAS, table load: 1,814 kg, overall weight: 7,485 kg, spindle speed (max.): 10,000 rpm, spindle motor power: 44,700 W, number of slots in tool magazine: 30, number of axes: 3, This 3-axis HAAS VF-3YT/50 was manufactured in 2019. It features an impressive X-axis travel of 1,016 mm, Y-axis travel of 660 mm, and Z-axis travel of 635 mm. The machine is equipped with a high-performance spindle capable of 10,000 rpm and a 30-position automatic tool changer. If you are looking to get high-quality machining capabilities, consider the HAAS VF-3YT/50 vertical machining centre we have for sale. Contact us for further details. • Condition: Used, fully operational • Operating/cycle hours: 6,744 h • Spindle/cutting hours: 4,454 hTravels • Spindle nose to table: 201–836 mm • Rapid traverse: 18 m/min • Maximum cutting feed: 12.7 m/minSpindle and tool changer • Maximum torque: 460 Nm • Drive system: Vector drive with 2-speed gearbox • Tool changer capacity: 30 toolsTable • Table size: 1,372 × 610 mm • T-slots: 7 • T-slot width: 15.9–16 mmShipping • Note: Dimensions listed as 1,370 × 660 × 630 mm are not overall machine dimensions • Export shipping dimensions (approx.): 3,970 × 2,600 × 3,230 mm • Approx. shipping weight: 7,485 kg Additional equipment Lhsdpfx Aszwd Aujbysn • Chip conveyor with four additional augers • Haas Chip Lift • Through-Spindle Coolant (TSC), 300 psi / 21 bar • Programmable coolant nozzle • Coolant chiller • ACF 25-micron auxiliary coolant filter • Coolant mist condenser • Minimum Quantity Lubrication (MQL) • Automatic air gun • Through-Tool Air Blast (TAB) • PulseJet system • Renishaw Wireless Intuitive Probing System (WIPS) with probe riser block • Fourth-axis drive and wiring • High-Speed Machining (HSM) • DWO/TCPC (Dynamic Work Offsets/Tool Center Point Control) • RTAP-3 synchronized tapping • Wi‑Fi network connection and Wi‑Fi camera • Automatic door • High-intensity lighting • Approximately 15 tool holders • Complete documentation Technical Specification Taper Size ISO 50

Condition: like new (used), Year of construction: 2023, Haas TM2-P Year: 2023 X-1016, Y-406, Z-406 RPM: 6,000 BT 40 WIPS HSM 4th axis connection Very few operating hours Like new! Lhjdpfezua Hwex Abyen

Condition: ready for operation (used), Year of construction: 2011, controller manufacturer: HAAS, This 3-axis HAAS VF-4 was manufactured in 2011. It features a generous X-axis travel of 1270 mm, Y-axis travel of 508 mm, and Z-axis travel of 635 mm. The machine is equipped with a 40-tool automatic tool changer and includes a probe and toolsetter for enhanced precision. If you are looking to get high-quality machining capabilities, consider the HAAS VF-4 vertical machining centre we have for sale. Contact us for further details. Lhodpfxszxp D Hs Abysn

Condition: excellent (used), Year of construction: 2022, functionality: fully functional, feed length X-axis: 3,048 mm, feed length Y-axis: 813 mm, feed length Z-axis: 762 mm, controller model: NGC, spindle speed (max.): 7,500 rpm, number of slots in tool magazine: 30, Equipment: chip conveyor, documentation/manual, 50-taper spindle with a 2-speed gearbox. Customizable to meet your specific requirements. Ideal for working with tougher materials and larger-diameter cutting tools. Lhjdpfxszr U S Ns Abyon

Condition: used, Year of construction: 2013, travel distance X-axis: 508 mm, travel distance Y-axis: 406 mm, travel distance Z-axis: 508 mm, spindle speed (max.): 15,000 rpm, Equipment: chip conveyor, TECHNICAL DETAILS Travel range, X-axis: 508 mm Travel range, Y-axis: 406 mm Travel range, Z-axis: 508 mm Distance from spindle nose to machine table: max. 610 mm Distance from spindle nose to machine table: min. 102 mm Rated power: max. 22.4 kW Torque: max. 122.0 N·m at 2,000 rpm Torque with optional gearbox: max. 339 N·m at 450 rpm Spindle design: metric Spindle taper: SK40 Spindle speed: 15,000 rpm Table length: 660 mm Table width: 356 mm Width of T-slots: 15.90 to 16.00 mm Center distance of T-slots: 125 mm Number of T-slots in standard configuration: 3 Load capacity of the table with uniform distribution: max. 1,361 kg Feed rate during machining: max. 16.5 m/min Rapid traverse, X-axis: 25.4 m/min Rapid traverse, Y-axis: 25.4 m/min Rapid traverse, Z-axis: 25.4 m/min Tool diameter (overall): max. 89 mm Tool weight: max. 5.4 kg Tool-to-tool change time (average): 4.20 s Chip-to-chip change time (average): 4.50 s MACHINE DETAILS Coolant tank capacity: 208 l Input voltage AC, three-phase, low: 220 V AC Full-load current, three-phase, low: 70 A Input voltage AC, three-phase, high: 440 V AC Full-load current, three-phase, high: 35 A Weight: 3539 kg The seller estimates the operating hours to be approximately 9,000 hours. EQUIPMENT 20-position tool changer Chip conveyor Internal cooling, 21 bar Coolant mist extraction system Additional coolant filter Ljdpfjzxhmtex Abyehn

Condition: excellent (used), Year of construction: 2017, functionality: fully functional, This is the Haas equivalent of the Fanuc Robodrill and very impressive it is! Shown running on our race car components, we can help with training and setup if required pictures show components we are currently making on the DM2 5th Axis enabled 4th axis Interface, 5th axis Interface, Coolant, Interlocked guards, High speed machining enabled Low Volt Light, Programmable Coolant Nozzle, Remote Hand Wheel, Swarf Auger, Through Spindle Coolant, USB Port Control HAAS Machine Dimensions 2811 x 2463 x 2583mm Machine Weight 2427kg Max & Min distance from table to spindle 152 - 546mm Maximum Cutting Feedrate 30.5m/minute Maximum Tapping Capacity M12 (Aluminium) Maximum Tool Diameter 64mm Maximum Tool Diameter with Empty Adjacent Pockets 64mm Maximum Tool Length 178mm Maximum workpiece weight 113kg Memory 1Gb Rapid Feedrates 61m/minute Spindle Motor Power 40HP Spindle Speed Lhjdpfxoydil Ns Abyen 15000rpm T- Slots 3 x 16mm Table Size 864 x 381mm Tool Change Capacity 18 + 1 Tool Change Time (Chip to Chip) 1.6 seconds Tool Size BT40 Traverses XYZ 711 x 406 x 394mm

Condition: like new (used), Year of construction: 2022, operating hours: 105 h, functionality: fully functional, Haas ST50 Horizontal Turning Machine Slant Bed Lathe. Bought new directly from Haas and installed in Early 2023. Lhsdpfx Aboxrf Steyon As a "last of line" model from Haas (which they've yet to make this size since), this machine is fully loaded and as you can see from the build list below it is very well spec'd. It also only has 105 hours use. Viewing advised and welcome at our workshop in Canterbury, Kent. Videos can be sent and or uploaded to Youtube also. This machine and others we are selling are also listed else where. Please get in touch with us at Showan Hydraulics, Barham, Kent if you require any further details. £325,000 + VAT PRODUCT OVERVIEW • Maximum Capacity: 25.5" x 80" (648 x 2032 mm) • Spindle Bore: 8.5" (216 mm) • Swing Over Bed: 34.5" (876 mm) • Main Drive: 55 hp (41 kW) vector drive • Spindle Speed: 1200 rpm, 2-speed gearbox • Spindle Nose: Front and rear A2-15 • Chucks: 25" (635 mm) Manual 3-Jaw and 4-Jaw Chucks • Turret: 12-station bolt-on turret • Tailstock: Programmable servo with MT6 quill • Control System: 15" touchscreen interface with USB port, memory lock keyswitch, and colour remote jog handle • Additional Features: Rigid tapping and variable flow coolant pump _____ STANDARD FEATURES • Bolt-On Toolholder Kit: Comprehensive set of toolholders, sleeves, coolant block, and turning stick clamps for flexible setup. • 1200-RPM Spindle: Powerful 55 hp (41 kW) A2-15 spindle with 2-speed gearbox for optimal torque and speed. • Program Memory: 1 GB onboard memory for program storage and backup. • Coolant System: 95-gallon (360 L) tank with 3/4 hp (0.6 kW) pump del

Condition: good (used), Year of construction: 2006, Haas VF-5B/40HE vertical machining center, year 2006. Lhjdpozcu Imjfx Abyen

Condition: ready for operation (used), Year of construction: 2008, travel distance X-axis: 1,270 mm, travel distance Y-axis: 508 mm, travel distance Z-axis: 635 mm, spindle speed (max.): 12,000 rpm, spindle motor power: 22,400 W, number of axes: 3, This 3-axis HAAS VF-4SS vertical machining center was manufactured in 2008. It features a 1270 × 508 × 635 mm travel range, 22.4 kW spindle power, and a maximum spindle speed of 12,000 rpm. The machine includes a 40 + 1 position tool changer and a high-speed machining package. If you are looking to get high-quality milling capabilities, consider the HAAS VF-4SS machine we have for sale. Contact us for more information. • Distance spindle–table: 102 mm • Tool holder taper: CT40 (DIN 69871) • Max cutting feed: 20.5 m/min • Rapid feed (X/Y/Z): 35.6 m/min • Tool changer type: Random vertical • Tool magazine capacity: 40 + 1 positions • Data interface: USB • Options/Features: • Through-spindle coolant system (21 bar) • 4th axis drive and wiring (prepared for 4th axis) • Intuitive programming system • Dual spindle orientation • Coordinate rotation system • Macro variables and scaling functions • High-speed machining package Additional equipment • Screw-type chip conveyor • Auxiliary high-pressure filtration system Ledex D Irmepfx Abyehn

Condition: ready for operation (used), Year of construction: 2015, travel distance X-axis: 1,270 mm, travel distance Y-axis: 660 mm, travel distance Z-axis: 635 mm, controller manufacturer: HAAS, table width: 584 mm, table length: 1,321 mm, table load: 1,815 kg, spindle speed (max.): 8,100 rpm, spindle motor power: 22,400 W, number of slots in tool magazine: 24, number of axes: 4, This 4-axis HAAS VF 5/40 was manufactured in 2015. It features an X-axis travel of 1270 mm, Y-axis travel of 660 mm, and Z-axis travel of 635 mm. The machine includes a tool changer capacity of 24 positions and a maximum table load of 1815 kg. If you are looking to get high-quality machining capabilities, consider the HAAS VF 5/40 vertical machining centre we have for sale. Contact us for further details. • X-axis rapid traverse: 18.0 m/min • Y-axis rapid traverse: 18.0 m/min • Z-axis rapid traverse: 18.0 m/min • Distance spindle nose to table (max): 742 mm • Distance spindle nose to table (min): 107 mm • Max spindle torque: 122.0 Nm @ 2000 rpm Ljdpez Erwtsfx Abyohn • Table T-slot width: 14 mm • Table T-slot pitch: 80 mm Additional equipment • Included documentation: Manuals and CE Declaration of Conformity Technical Specification Taper Size BT 40

Condition: ready for operation (used), Year of construction: 2007, spindle speed (max.): 3,400 rpm, travel distance X-axis: 287 mm, travel distance Z-axis: 864 mm, total height: 2,000 mm, controller manufacturer: HAAS, number of axes: 2, This HAAS SL-30HE was manufactured in 2007. A robust horizontal turning machine featuring a turning diameter over bed of 762mm and a length of 860mm. It includes a VDI tool turret with 12 positions and a chip conveyor. Ideal for precise and efficient turning operations. Contact us for more information about this machine. Lhedpfx Absyar Thsyon Machine Benefits Technical Machine Benefits • Turning diameter over bed: 762 mm • Tool turret vdi: 12 tool positions • Turning length: 860 mm Extra Information Machine still under power Dimensions Machine Depth 3300 mm

Condition: ready for operation (used), Year of construction: 2015, operating hours: 5,792 h, travel distance X-axis: 1,016 mm, travel distance Y-axis: 508 mm, travel distance Z-axis: 635 mm, controller manufacturer: HAAS, table load: 794 kg, spindle speed (max.): 12,000 rpm, number of axes: 3, This 3-axis HAAS VF-3SS vertical machining center was manufactured in 2015. It features a 1,372 × 457 mm table, a maximum load of 794 kg, and a spindle speed of 12,000 rpm. The machine includes a 30+1 side-mount ATC and a rapid traverse of 30.5 m/min. If you are looking to get high-quality milling capabilities, consider the HAAS VF-3SS machine we have for sale. Contact us for more information about this machine. • Electrical: • Voltage: 354 / 488 V • Phase: 3 • Frequency: 50/60 Hz • Full load: 40 A • Largest load: 70 A • Short circuit interrupting capacity: 10,000 A • Short circuit current: 5,000 A RMS symmetrical • Machine hours (from control): • Power on time: 19,635 h • Cycle start time: 8,564 h • Table: Lodpfx Asx D I Smobyehn • Size: 1,372 × 457 mm • Tool changer: 30+1 side-mount ATC • Control unit: Haas CNC Control

Condition: excellent (used), Year of construction: 2013, Available end of July. Technology Inline direct drive Lhedpfx Asyimncjbyjn Speed 12,000 rpm Power 22 kW Tool holder SK40 Tool changer SMTC, 41 positions Technology 2 axes, with counter bearing B-axis -35° / +110° C-axis 360° Clamping surface ø630 x 500 mm Table load (max.) 300 kg Cooling Standard coolant including P-Cool and through-spindle cooling (TSC) Renishaw probe WIPS system with touch probe and tool measurement 8M functions Rotating and scaling 16MB memory storage HSM high speed milling Rigid tapping Machine cycle time: 5,446 h Machine power-on time: 21,246 h