Used Grundfos Ch 2 30 for sale (70)

Condition: new, Year of construction: 2024, NEW Grundfos - The pump is fitted with a 3-phase, fan-cooled, permanent-magnet, synchronous motor. The motor efficiency is classified as IE5 in accordance with IEC 60034-30-2. The motor includes a frequency converter and PI controller in the motor terminal box. This enables continuously variable control of the motor speed, which again enables adaptation of the performance to a given requirement. An operating panel on the motor terminal box enables setting of required setpoint as well as setting of pump to "Min." or "Max." operation or to "Stop". The Grundfos Eye indicator on the operating panel provides visual indication of pump status: Tedpfxjyug Hxj Aa Ijc "Power on": Motor is running (rotating green indicator lights) or not running (permanently green indicator lights) "Warning": Motor is still running (rotating yellow indicator lights) or has stopped (permanently yellow indicator lights) "Alarm": Motor has stopped (flashing red indicator lights). Communication with the pump is possible by means of Grundfos GO Remote (accessory). The remote control enables further settings as well as reading out of a number of parameters such as "Actual value", "Speed", "Power input" and total "Power consumption". The terminal box has a number of inputs and outputs enabling the motor to be used in advanced applications where many inputs and outputs are required: • two dedicated digital inputs • three analog inputs, 0(4)-20 mA, 0-5 V, 0-10 V, 0.5 – 3.5 V • 5 V voltage supply to potentiometer and sensor • one analog output, 0-10 V, 0(4)-20 mA • two configurable digital inputs or open-collector outputs • two Pt100/Pt1000 inputs • LiqTec, dry-running protection sensor input • Grundfos Digital Sensor input and output • 24 V voltage supply for sensors • two signal-relay outputs (potential-free contacts) • GENIbus connection • interface for Grundfos CIM fieldbus module.

Condition: used, Centrifugal pump, high pressure pump, water pump -Max. Delivery rate: 2.0 m³/h Tsdpfxsdz Drpj Aa Iec -Dimensions: 360/140/H340 mm -Weight: 11 kg

Condition: good (used), volume flow: 85 m³/h, power: 11 kW (14.96 HP), input frequency: 50 Hz, type of input current: three-phase, Grundfos TPD pumps are single-stage, tightly connected in-line centrifugal two-head pumps, with mechanical shaft seal and primarily for applications such as heating / cooling / district power. Type: TPD 80-330 / 2 A-F-A-BAQE Technical pump speed: 2930 rpm Nominal flow: 85.6 m³ / h Nominal lifting height: 25.9 m Maximum lifting height: 33 m Actual impeller diameter: 157 mm Materials Pump housing: Cast iron Impeller: Cast iron Material code: A Installation Ambient temperature range: -30 .. 60 ° C Maximum operating pressure: 16 bar Max. Pressure at the specified temperature: 16 bar / 140 ° C Connection size: DN 80 Pressure value for connection: PN 16 Port-to-port length: 440 mm Flange size for motor: FF300 Pump Tedpeg I Utpjfx Aa Ijc Transported liquid temperature range: 0 .. 120 ° C Density: 998.2 kg / m³ Electrical data Engine: Rated power - P2: 11 kW Mains frequency: 50 Hz Rated voltage: 3 x 380-415D / 660-690Y V Rated current: 12.0-11.8 A Starting current: 660-780% Rated speed: 2930 rpm Number of poles: 2 Housing classification (IEC 34-5): 55 Powder / Spray Insulation class (IEC 85): F Motor protection PTC Net weight: 303 kg Gross weight: 328 kg Purchase and purchase of industrial equipment and machinery. Wide Range of Used Machinery, Industrial Equipment

Condition: like new (used), Grundfos MGE100LA 2-FF215-JA-300 pump 3.00 kW Speed: 2900 - 4000 rpm Weight: 24 kg You are welcome to visit us for an inspection. Tsdjzzmhzepfx Aa Ioc We can also arrange cost-effective shipping for you! You will receive a proper invoice. For foreign customers, a net invoice can also be issued. A valid VAT identification number is required. Subject to prior sale. Visit our shop and browse our other offers. The company names and trademarks mentioned are the property of their respective owners and are used solely for identification and description of the products. Deviations from technical data as well as errors in the description of the article may occur and are subject to change.

Condition: new, Grundfos CRN15-17 A-FGJ-G-V-HQQV Vertical centrifugal pump, Model: A96502060P31230, Serial No.: 0001, with MG160MD2-42FF300-H3 pump motor - 15 kW - Serial No.: 85U17526, unused, 100% functional, scope of supply as shown in the photos. ATTENTION: Please request separate quotes for packaging and shipping costs! Tedey U Tmtspfx Aa Ijc

Condition: used, Year of construction: 2020, functionality: limited functionality, overall weight: 150 kg, GRUNDFOS Electronically Controlled Dry-Running Pump TPE 100-250/2-S A-F-A-BAQE-ND1 Single-Stage Inline Pump Art. 99114824 PN16. 3 x 380-500 V DN100 with MGE160MH-2-FF300-JA Motor We are offering the Grundfos electronically controlled dry-running pump. ⭐︎ Condition: Good (used) The electronically controlled dry-running pump is used but fully operational. The pump was functioning flawlessly up until removal a few weeks ago. Manufacturer: Grundfos Model: TPE 100-250/2-S A-F-A-BAQE-ND1 Description: Single-stage inline pumps with speed-controlled MGE motor Frequency converter: integrated Pump speed: 2930 rpm Rated flow: 135 m³/h Rated head: 20.1 m Mechanical seal: BAQE Pump housing: Cast iron Impeller: Cast iron Gross weight: 157 kg For further technical details, please refer to the nameplate. Scope of delivery as shown. Inspection prior to purchase is possible and expressly encouraged. 2 units available. Price: per unit #Shelf 21-1-9 Tsdpfoyc T Apsx Aa Ioc Shipping possible, but buyer pays shipping costs. Single-stage volute pump with opposing suction and discharge ports in inline design. Suction and discharge ports have the same diameter. The pumps are constructed according to the top-pull-out principle, i.e., the pump head (motor, headpiece, and impeller) can be easily removed for servicing or maintenance while the pump housing remains in the piping. The pump is equipped with an unbalanced rubber bellows seal. The mechanical seal complies with EN 12756. Piping connection via DIN flanges PN 16 according to EN 1092-2 and ISO 7005-2. The pump features a fan-cooled permanent magnet synchronous motor. The motor efficiency corresponds to energy efficiency class IE5 according to IEC 60034-30-2. For speed control, the motor is equipped with a frequency converter and PI controller, both integrated into the motor terminal box. Electronic speed control enables continuous adaptation of motor speed and thus pump output to current demand. The pump is equipped with a differential pressure sensor.

Condition: new, functionality: fully functional, Grundfos TPE 50-430/2 S-A-F-A-BQQE-LD1 Single Stage Close Coupled In Line Centrifugal Pump. Specifications: DN50 flanges 345mm between flanges Q = 35.1m3/h H = 33.9m n= 2920 /min Good working condition. Please check out our other listings as well. Tsdpfx Aajtp A Shj Isc

Condition: used, MG160MB2-42FF300-H3, 160BB, Grundfos, 3-phase AC standard motor Model: MG160MB2-42FF300-H3 Type: 160BB Tsdpfjutan Esx Aa Ioc Condition: Used

Condition: used, Year of construction: 2016, functionality: fully functional, machine/vehicle number: 3151, Stainless Steel Heated Filtration System for Machining Center Capacity: 28 l Max. Operating Pressure: 16 bar Max. Operating Temperature: 95°C Todpjwtga Rofx Aa Iec Grundfos (Pump): Type: MTR15-14/12A-W-A-HUUV n: 2924 rpm Hz: 50 kW: 11 Q: 17 m3/h Hmax: 169 m Grundfos (Motor): Type: MG160MB2-42FF300-H3 The Wolftechnik stainless steel filtration system, custom designed for the machining center WTBF85-F50-SS-TTV-GD-PN16, offers a high-quality solution for filtration in demanding manufacturing processes. Its heating capability ensures continuous operation even at low temperatures, preventing disruptions in production. With a high-performance Grundfos pump and a reliable motor, the system provides efficient flow control and continuous filtration.

Condition: excellent (used), Grundfos TPED 50-160 / 2-S AFA-BAQE APPLICATION AREAS - Heating systems - Local hot water supply systems - cooling and air conditioning systems FEATURES AND ADVANTAGES - Low power consumption - Correction according to the existing working conditions - Easy to install Tjdpfofuappox Aa Ioc Technical data: Frequency of rotation 2900 rpm Nominal supply 17 m 3 / h Nominal head 12 m Max hydrostatic head 160 dm Shaft seal BAQE liquids: Working fluid water Fluid temperature range 0 ... 120 ° C temperament. Liquids 20 ° C density 998,2 kg / m 3 materials: Pump housing cast iron EN-JL1040 ASTM A48-40 B Impeller cast iron EN-JL1030 ASTM A48-30 B Electrical data: Motor type 80B Number of poles 2 Nominal power - P2 2 x 1.1 kW Industrial frequency 50 Hz Nominal voltage 3 x 380-500 V Rated current 2.15-1.80 A Cos is a force characteristic 0.91-0.82 Nominal speed 360-4000 rpm Energy efficiency 88.5% Protection class (IEC 34-5) IP55 Insulation class (IEC 85) F Motor protection Yes. Engine number 98362352 assembly: Maximum ambient temperature 50 ° C Max. working pressure 16 bar Max. Pressure at a given temperature 16 bar / 120 ° C Standard flange DIN Connection code F Pipe connection DN 50 Permissible pressure PN 16 Mounting length 340 mm mm Motor flange size FF165 Net weight 95 kg

Condition: excellent (used), For sale: a Grundfos CRK2-260 AMA AUUV multi-stage vertical pump with a three-phase Grundfos MG 100LB2-28FT130-C motor. The unit is fully functional, tested, and ready for operation. Its technical condition is very good, with normal signs of wear and tear resulting from use. Pump specifications: Manufacturer: Grundfos Model: CRK2-260 AMA AUUV Pump power: 3.0 kW Power supply: 3-phase Frequency: 50 Hz Flow rate: 16–58 l/min Head: 107–225 m Motor specifications: Manufacturer: Grundfos Model: MG 100LB2-28FT130-C Power: 3.0 kW Power supply: 200–220 V Δ / 346–380 V Y (50 Hz) Rotational speed: 2880–2910 rpm Protection class: IP54 Insulation class: F Tjdpfx Aajzn N T Tj Ijc

Condition: used, machine/vehicle number: 98362357, power: 2.2 kW (2.99 HP), input voltage: 500 V, input frequency: 60 Hz, input current: 4 A, type of input current: three-phase, type of cooling: air, rotational speed (max.): 4,000 rpm, protection type (IP code): IP55, Pump from a well-maintained installation, with few operating hours. Tedpezb E Axjfx Aa Ioc

Year of construction: 2023, condition: used, Pump speed 2.934 U/min Nominal delivery flow 45 m³/h Rated head 92,8 m Capacity 18,5 kw In our assessment, the pumps are in good used condition. Tedpfxozz S Nqe Aa Iec Accessories, tools, and clamping devices shown are only included if explicitly stated in the additional information. Technical data and specifications are subject to change without notice. Prior sale is reserved.

Condition: excellent (used), Pressure centrifugal pump Vertical centrifugal pump Grundfos CR 90-3 A-F-A-E-EUBE Tjdpfx Aashy Nx Ee Ijc more piece Vertical, multistage centrifugal pump with suction and discharge ports on the same level. The pump head and base are in cast iron - all other wetted parts are in stainless steel (EN 1.4301) Rated flow 90 m³/h Rated head 65.5 m Max pressure at stated temp 16 bar / 120 °C Type of connection DIN Size of inlet connection DN 100 Pumped liquid Water Liquid temperature range 0 .. 120 °C Selected liquid temperature 20 °C Density 998.2 kg/m³ Electrical data Motor type SIEMENS Rated power - P2 22 kW 2940 rpm Mains frequency 50 Hz Rated voltage 3 x 380-415D/660-690Y V Rated current 41,5-39,5/24,0-23,5 A Cos phi - power factor 0.86 Rated speed 2945 rpm Number of poles 2 Enclosure class (IEC 34-5) IP55

Year of construction: 2012, condition: ready for operation (used), functionality: fully functional, A complete cooling water unit that was used for cooling screw compressors. Pump unit with machine frame, consisting of: - 3 x Grundfos CRNE45-2-2 A-F-G-V-HQQV centrifugal pumps (Year of manufacture: 2012) Q = 45 m³/h, H = 30.6 m, P2 = 5.5 kW - 6 x manual stainless steel shut-off butterfly valves DN 80 - 3 x basket strainers DN 80 - 3 x check valves DN 80 - 1 x pressure relief valve - 2 x Rosemount GP6 S22 C1 pressure transmitters - 6 x stainless steel gauges Cl. 1 - 1 x GRP pipe - 1 x mounting frame Dimensions: Length: 2400 mm Width: 2000 mm Height: 1400 mm Weight: 780 kg Heat exchanger unit with frame, consisting of: Tedpoywuihofx Aa Ioc - 2 x bolted plate heat exchangers, Funke Apparatebau GmbH (Year of manufacture: 2001) Type: FPS 21-100-1-E Volume: 29.2 / 29.8 liters Max. operating pressure: 10 bar Max. temperature: 80°C - 8 x manual intermediate flange shut-off butterfly valves, stainless steel - 1 x KSB BOA electric valve with Auma SAR actuator and MATIC head, including Harting connector - 2 x PT 100 sensors - 6 x analog thermometers, stainless steel Cl. 1 - 2 x PE pipework with bends 110x65mm Gerodur - 1 x expansion vessel - 1 x mounting frame Dimensions: Length: 2200 mm Width: 2000 mm Height: 2000 mm Weight: 1500 kg

Condition: new, Year of construction: 2022, functionality: fully functional, NEW Grundfos Pump CRN 10-12 A-FGJ-G-E-HQQE | Stainless Steel AISI 316 | 4 kW Condition: Brand new, never used. Model: CRN 10-12 A-FGJ-G-E-HQQE Manufacturer: Grundfos (Leading pump solutions provider) DEVICE DESCRIPTION The item for sale is a high-performance, vertical multistage centrifugal pump from the CRN series. This is a version made entirely from acid-resistant stainless steel (AISI 316), setting it apart from the standard cast iron models (CR). It is designed for operation in the most demanding industrial conditions, ensuring reliability when handling aggressive and demanding liquids. The pump is an ideal solution for businesses seeking a high-efficiency device, ready for immediate installation in water treatment systems, technological processes, or high-pressure setups. _____ KEY TECHNICAL DATA • Rated flow: 10 m3/h • Rated head: approx. 96.7 m (max up to 122 m) • Motor power: 4 kW • Power supply: 3-phase • Rotational speed: 2900 rpm • Maximum operating pressure: 25 bar • Liquid temperature range: -20°C to +120°C • Number of impellers: 12 Tedpjx Im Ahofx Aa Ijc • Year of manufacture: 2022 CONSTRUCTION AND MATERIALS • Material configuration (G): All liquid-contacting parts are made from stainless steel EN 1.4401 / AISI 316 (providing maximum corrosion resistance). • Shaft seal (HQQE): Durable cartridge mechanical seal made from silicon carbide (SiC/SiC) with EPDM elastomers. Guarantees longevity and leak-tight operation even with hot water. • Connection (FGJ): Universal flanged system (DIN/ANSI/JIS), allowing easy adaptation in existing installations. _____ APPLICATIONS Thanks to its acid-resistant construction, the CRN pump is suitable for: 1. Chemical and pharmaceutical industries (pumping acids, alkalis, aggressive media). 2. Filtration and water treatment systems (reverse osmosis, ultrafiltration). 3. Industrial washing systems and CIP/SIP cleaning setups. 4. Process water installations in brewing, dairy, and food industry. _____ WHY BUY THIS PUMP? • Premium product: The CRN series is the “Mercedes” among vertical pumps. • Time-saving: Device is available immediately (no long lead times from the manufacturer). • No usage marks: The pump is brand new, properly stored, and ready to operate at full capacity. Important: Please verify that the electrical and hydraulic parameters match your project requirements before purchase.

Condition: used, Grundfos Vertical Water Pump Complete with isolator valve Power isolator switch 1.5 kw 5.7 m3/hr H max 60m Tedpfxsz E Nhvo Aa Iec

Condition: new, Grundfos CRN32-5-2 A-F-G-E-HQQE Vertical centrifugal pump CRN 32-5-2 A-F-A-E-HQQE Vertical, multistage centrifugal pump with opposing suction and discharge connections (inline design). The pump components in contact with the medium are made of high-quality stainless steel. The cartridge seal promises high reliability and ease of servicing. Power is transmitted via a rigid, split coupling. The pipe connection is made via combined DIN flanges. The pump is equipped with a 3-phase, fan-cooled asynchronous motor. Manufacturer: Grundfos Manufacturer Product Group: Vertical Centrifugal Pumps Manufacturer Product Group: Vertical Centrifugal Pumps CRN Centrifugal pump CRN Manufacturer article number: 96122358 Connection inlet side: Flange Connection outlet side: Flange Tjdpfxswbfigj Aa Ioc Connection standard inlet side: EN 1092-2 Nominal diameter, connection outlet side: DN 65 Design: Vertical Speed: 2924 min Motor output power: 11.0 kW Protection class: IP55 Max delivery head: 90.2 m Max working pressure: 16 bar Weight: 193.2 kg List price: 14,844.00 € Financing through our bank is also possible. komplett-konzept.leasingo.de You can find more items in other sizes - new and used - in our store! International shipping costs on request!

Year of construction: 2011, condition: used, functionality: fully functional, A complete cooling water unit used for cooling screw compressors. Pump unit with machine frame consisting of: 3 x Type: CRN32-1-1 A-F-G-V-HQQV / 30 m³/h 10.7 meters, 1.5 kW 6 x manual stainless steel shut-off valves 1 x pressure relief valve 1 x Rosemount GP6 S22 C1 pressure transmitter 6 x stainless steel pressure gauges Cl.1 2 x Gerodur plastic pipes with elbow fittings, 140 x 8.3 mm 1 x mounting frame Heat exchanger unit with frame consisting of: 2 x bolted plate heat exchangers Alfa Laval Type: M6-MFG Volume: 11.2 liters Max. operating pressure: 10 bar Max. temperature: 80°C 6 x manual intermediate flange shut-off valves, stainless steel 2 x electric valves with Auma actuators with Harting connectors 2 x electric KSB BOA valves with Auma SAR 07.1-F10 actuators and MATIC heads with Harting connectors 2 x PT 100 thermometers 4 x analog thermometers stainless steel Cl.1 1 x Rosemount GP6 S22 C1 pressure transmitter 2 x PE welded pipe with bends 110x6.5 mm Gerodur 2 x PE pipe with bends 90x5.4 mm Gerodur 1 x expansion vessel Todpsyrxuvofx Aa Ioc 1 x mounting rack

Condition: new, functionality: fully functional, 8 units available. Various models in stock; for more information, please contact us. Export is possible. Tjdpfxeyypv Io Aa Ioc

Year of construction: 2023, condition: used, Pump speed 2.924 U/min Nominal delivery flow 21 m³/h Rated head 95,1 m Tjdezbvguopfx Aa Iec Capacity 11 kw In our assessment, the pumps are in good used condition. Accessories, tools, and clamping devices shown are only included if explicitly stated in the additional information. Technical data and specifications are subject to change without notice. Prior sale is reserved.

Condition: excellent (used), functionality: fully functional, volume flow: 163 m³/h, input frequency: 50 Hz, NB 80-160/147-127 A-F2-A-E-BAQE Non-self-priming, single-stage centrifugal spiral pump Pumped liquid: water Liquid temperature range: 0 .. 120 °C Density: 998.2 kg/m³ Technical: Speed: 2940 rpm Nominal volume flow: 163 m³/h Nominal head height: 17.1 m Actual diameter of the impeller: 147-127 mm Nominal diameter of the impeller: 160 mm Primary shaft seal: BAQE Maximum ambient temperature: 60 °C Maximum operating pressure: 16 bar Flange standard: EN 1092-2 Pump inlet: DN 100 Tjdpfx Aajrp Ef Ej Isc Pump outlet: DN 80 Pressure limit: PN 16 Nominal power 11 kW Mains frequency: 50 Hz Nominal voltage: 380V 3 phases Nominal current: 20.6 weight: 162 kg ​

Condition: ready for operation (used), Grundfos MG 112 MS 2-28 FT 136-C three-phase motor SN 1100029148, used, minor signs of wear, 100% functional, scope of delivery as per photos Tedjqyq Nqjpfx Aa Iec

Condition: good (used), Centrifugal pump, high-pressure pump, water pump, multi-stage vertical centrifugal pump -Voltage: 380-415 V 690 W -Max. flow rate: 2 m³/h -max. H: 36/46 m -Max. pressure: 6 bar -Maximum temperature: 90 °C -Price: per piece -Quantity: 2 pieces Tedped Tk Sqsfx Aa Isc -Dimensions: 400/143/H203 mm -Weight: 12.4 kg

Condition: new, functionality: fully functional, overall weight: 106 kg, Brand new, in original packaging. Quantity: 2 units. Various models available, please contact us for more information. Tedsyyl Utspfx Aa Ijc