Used Gear Testing Machine for sale (75,765)

Condition: used, Year of construction: 2011, machine/vehicle number: 25621, workpiece diameter (max.): 360 mm, Equipped with: Gear Spindle Runout: -Radial (Bore): .00005 -Axial (Face): .00005 Pinion Spindle Runout: -Radial (Bore): .00005 Axial (Face): .00005 Axis Repeatability: -X: .0001 -Y: .0001 -Z: .0001 Axis Lost Motion: -X: .00005 -Y: .00005 -Z: .00005 Fanuc 160I MB Control Base Work Holding Draw Bars Automatic Doors Spindle Chiller Transformer Hydraulic System Festo Pneumatics Automation Interface Available SPECIFICATIONS: Maximum Gear Outside Diameter: 360 mm (14.2") Maximum Pinion Outside Diameter: 340 mm (13.4") Maximum Pinion Drive Speed: 3000 rpm Maximum Gear Drive Speed: 1500 rpm Offset Vertical 150 mm ( 5.9") Pinion Cone Range: (90) (135-350) (70) (146-438)* (110) (51-343)* Gear Cone Range: (90) (65-280) (70) (78-306)* (110) (56-284)* Iodpfxexdfanj Ag Uotb Standard Testing Torque Load 2 to 90 Nm (1.5 to 66 ft-lb). Parallel Axis - face-to-face 147 - 362 - Center Distance -7 - 250 Pinion Spindle Bore 39T - Diameter 99.2 mm (3.9") - Depth 419 mm (16.5") Gear Spindle Bore 39T - Diameter 99.2 mm (3.9") - Depth 250 mm (9.8") Floor Space (width & length) 2100 x 2550 mm (82.7 x 100.4") Height (to top of stack light) 2750 mm (108.3") Weight (base machine) 9100 Kg (20062 lbs)

Condition: good (used), workpiece diameter between centers: 2,286 mm, The No. 61 Angular Hypoid Tester is designed to test large bevel and hypoid gears up to 90" diameter and with shaft angles from 0 - 135 degrees. Spur, helical and internal gears can also be accommodated. The drive or pinion spindle can be rotated in either direction at a recommended spindle speed of 600 RPM. It is mounted in a head which is vertically adjustable on a column, so that the spindle can be offset either above or below the center line of the gear spindle for testing hypoid gears. The pinion head column is adjustable angularly in a horizontal plane to permit testing of gears of any shaft angle from 0 - 135 degrees. Specifications: Centerline of Drive Spindle to Nose of Brake Spindle (90 degrees shaft angle and without face plate): 38-1/2" Max. / 7-5/8" Min. Centerline of Brake Spindle to Nose of Drive Spindle (90 degrees shaft angle and without face plate): 60" Max. / 10" Min. Centerline of Brake Spindle to Nose of Drive Spindle (90 degrees shaft angle and with 54" face plate): 60" Max. / 28" Min. Centerline of Brake Spindle to Centerline of Drive Spindle (For Spur Gears): 56" Max. / 6" Min. Distance Between Nose of Brake Spindle and Nose of Drive Spindle (for spur gears): 36-1/2" Max. / 0" Min. Offset of Drive Spindle Either Above or Below Centerline of Brake Spindle: 10" Range of Shaft Angles: 0 - 360 Degrees Maximum Diameter of Gear: 90" Diameter of Face Plate: 54" Outboard Bearing: 3" Diameter Hole Spindles: RPM of Drive Spindle Pulley Set No. 1: 100 - 400 RPM of Drive Spindle Pulley Set No. 2: 250 - 600 Diameter of Taper Hole (large end): 6" Taper Per Foot: 3/4" Depth of Taper: 8" Itsdjrtrzdjpfx Ag Ujb Hole Through Spindle: 5-1/2" Net Weight of Machine: 20,000# Net Weight of Machine W/Outboard Support and Bed Plate: 24,000#

Condition: good (used), Year of construction: 2002, Clampable cutter head type (max.) 460 mm Cutter head weight (max.) 150 kg Mounting disc diameter for cutter heads (Ø) 360 mm Itjdow N S E Aepfx Ag Ueb Mounting cone for cutter heads Nominal diameter Ø 58,227 mm travel -z axis 200 mm diagram-drawing enlargement ±10 - ± 500 µm weight of the machine ca. 2,3 t dimensions of the machine ca. 2 x 1,5 x 2,03 m In the manufacturing process for spiral-toothed bevel gears, the quality of the gear cutting gear cutting tools used plays a decisive role. Particularly in high gear cutting quality and a long service life can only be achieved with precisely can only be achieved with precisely adjusted cutterheads. The Oerlikon cutterhead setting and testing device CS 200 enables quick and easy setting of the individual knives and simple adjustment of the individual knives, it checks the position and documents the measurement results. The measuring sequence on the CNC-controlled testing device is partially automated: The individual actions for carrying out the actions for carrying out the sequence are displayed on the screen via the operator guidance. The positioning of the individual knives in the cutter head and the height of the knife tips is largely automatic thanks to a special sequence and is simultaneously documented by means of a run-out diagram. A subsequent measuring sequence checks the radial position of the inner and outer cutting edges of all knives in the cutterhead. If individual test parameters on the knives do not correspond to the the tolerance specifications, this can be individually repositioned. The combination of semi-automated setting sequence, operator-guided set-up actions and automatic operator-guided set-up actions and automatic measuring sequence, cutterheads can be can be set conveniently, quickly and with high precision. Operator-guided setting and test sequence - Graphic display of the cutter head design and the measurement results with tolerance check - Instructions for the operator in plain text Instructions for the operator in plain text (without coded information) - Simple assignment of the measurement results to the knives - Documentation of the setting and measurement results via printer- Setting and test sequence suitable for ARCON®, RSR, Spirapid, SPIRON®, TRI-AC® types - Interface for neutral data

Condition: good (used), Year of construction: 2004, Clampable cutter head type (max.) 460 mm Cutter head weight (max.) 150 kg Mounting disc diameter for cutter heads (Ø) 360 mm Mounting cone for cutter heads Nominal diameter Ø 58,227 mm travel -z axis 200 mm diagram-drawing enlargement ±10 - ± 500 µm weight of the machine ca. 2,3 t dimensions of the machine ca. 2 x 1,5 x 2,03 m In the manufacturing process for spiral-toothed bevel gears, the quality of the gear cutting gear cutting tools used plays a decisive role. Particularly in high gear cutting quality and a long service life can only be achieved with precisely can only be achieved with precisely adjusted cutterheads. The Oerlikon cutterhead setting and testing device CS 200 enables quick and easy setting of the individual knives and simple adjustment of the individual knives, it checks the position and documents the measurement results. The measuring sequence on the CNC-controlled testing device is partially automated: The individual actions for carrying out the actions for carrying out the sequence are displayed on the screen via the operator guidance. The positioning of the individual knives in the cutter head and the height of the knife tips is largely automatic thanks to a special sequence and is simultaneously documented by means of a run-out diagram. A subsequent measuring sequence checks the radial position of the inner and outer cutting edges of all knives in the cutterhead. If individual test parameters on the knives do not correspond to the the tolerance specifications, this can be individually repositioned. The combination of semi-automated setting sequence, operator-guided set-up actions and automatic operator-guided set-up actions and automatic measuring sequence, cutterheads can be can be set conveniently, quickly and with high precision. Operator-guided setting and test sequence - Graphic display of the cutter head design and the measurement results with tolerance check - Instructions for the operator in plain text Instructions for the operator in plain text (without coded information) - Simple assignment of the measurement results to the knives - Documentation of the setting and measurement results via printer- Setting and test sequence suitable for ARCON®, RSR, Spirapid, SPIRON®, TRI-AC® types - Interface for neutral data Itsdsul Efmspfx Ag Ueb

Condition: good (used), Year of construction: 2007, max. wheel diameter 500 mm gear width 200-400 mm module 12 turning speeds 0-3250 U/min bracke pressure bis max. 95 Nm inner taper Konus #39 Control Fanuc 16 total power requirement 15 kW weight of the machine ca. 6 t dimensions of the machine ca. 2.350 x 2.240 x 2.500 mm HIGHLY FLEXIBLE TESTING OF HARD, FINISHED AND GREEN SPIRAL BEVEL AND HYPOID GEAR SETS The T 60 bevel gear testing machine is a CNC testing machine with three linear axes for the fully automatic hard and soft testing of spiral bevel and hypoid Itsdevr Hf Espfx Ag Ujb gear sets with a 90° axis angle. It offers versatile objective and subjective testing options with speeds up to 3,250 min and braking torques up to max. 95 Nm.

Condition: excellent (used), Year of construction: 1975, Breaking device . bar material dia. 10 - 45 mm bar material stranggepreßte NE-Stangen weight of the machine ca. 3 t Bending and breaking device simple and sturdy device to detect internal flaws in extruded non-ferrous metal rods Iodpfx Ageit Ev Te Ujtb +++++ Please note: The machine is dismantled and ready for loading. It is not possible to show it under power or make a video. Our offer includes already the best pictures. So we don’t have and won’t send additional pictures. +++++

Condition: excellent (used), Zwick / Roell Type: Z020 Allround-Line BT1-FR020TN.A50 Zwick / Roell Materials Testing Machine 20 kN Tensile & Compression Testing testXpert III For sale is a high-quality Zwick / Roell materials testing machine for professional tensile and compression testing of materials and components. The machine is suitable for metals, plastics, rubber, and many other materials and is typically used in laboratories, quality assurance, research, and education. Control is via PC using Zwick/Roell testXpert III software (data carrier & documentation included). Technical Data: Rated test force: 20 kN Test direction: tensile & compression Power supply: 230 V / 50–60 Hz / single-phase Power consumption: approx. 2.1 kVA Weight: approx. 150–180 kg Dimensions: approx. 856 × 650 × 1,545–2,114 mm Technical data (according to documentation & nameplate) Mechanics / Testing Ijdpjx Up Igofx Ag Ujtb Nominal force: 20 kN Testing direction: tensile & compression Max. test frequency: 0.5 Hz Crosshead: servo-electric Positioning accuracy: < 1 µm Speed range: 0.0005 – 1,000 mm/min Dimensions & Weight: Total height: approx. 1,545 – 2,114 mm (depending on crosshead position) Total width: approx. 856 mm Total depth: approx. 650 mm Working area width: 440 mm Weight: approx. 150 kg (base unit) approx. 180 kg with typical configuration Electrical Data Power supply: 230 V AC Phases: single-phase (1PH, N, PE) Mains frequency: 50 / 60 Hz Current consumption: approx. 8–10 A Power consumption: approx. 2.1 kVA Plug: Schuko (CEE 7) Measuring & Control Electronics: Internal data acquisition: 500 Hz Data transmission to PC: adjustable 10–100 Hz Interface: RS232 (COM) Electronics housing protection class: IP32 Important note: 'The table shown in the photos is not included in the sale.' Condition: used Scope of delivery: (see picture) - Zwick / Roell materials testing machine (20 kN) - Electronics unit - PC workstation (monitor, PC – please see photos for condition) - 2 measurement modules (Delock units) - Zwick/Roell testXpert III software (data carrier) - Original operating and technical documentation - Various connection and interface cables (Specifications are subject to change and errors excepted!) If you have any questions, we will be pleased to assist you by phone.

Condition: excellent (used), Year of construction: 2009, functionality: fully functional, Technical details max. wheel diameter 2-45 mm gear width 250 mm max. module 1,5 mm min. module 0,5 mm Control Fanuc 18i-MB weight of the machine ca. 2,2 t dimensions of the machine ca. 2100 x 1440 x 1700 m Additional information The combined CNC gear hobbing and worm milling machine KOEPFER MZ 120 is characterized by its flexible usability and is used in the small module area. Just by swiveling the milling spindle from the horizontal to the vertical position and selecting the corresponding operating mode of the CNC control, the worm milling machine becomes a gear hobbing machine and vice versa. Itodpfxex Ux Suo Ag Ujb CNC control Fanuc 18i-MB (Dialog/ISO) CNC axes = X-axis plunge axis Z-axis longitudinal axis C-axis workpiece spindle B-axis tool spindle V-axis loader axis longitudinal A-axis swivel axis tool spindle head (included as an option) Y-axis shift axis (included as an option) With the following production programs: Worm milling Hobbing Worm hobbing Bevel gear and spur gear milling Bevel gear hobbing Milling cycles = straight, oblique, crowned toothing, radial, radial-axial, co- and counter-rotating milling, roughing, finishing, worm gears, straight-toothed bevel gears, face gearing (option only in the partial process) Worms [Equipment] Coolant tank 300 liters KF with LNS Turbo MS 250 Chip conveyor, built in 2021!!! Kraft and Bauer fire extinguishing system Spiral conveyor Machine documentation [Technical data] Workpieces: Workpiece diameter 2-45 mm Max. workpiece length 250 mm Tooth length 150 mm Max. module in steel= 1 mm (gear hobbing) 1.5 mm (worm milling) 0.5 mm (bevel gear hobbing) Tools: Cutter diameter= 16-32 mm (gear hobbing) 40-63 mm (worm milling) Machine: Max. setting angle of milling head= +/- 45° (gear hobbing) +/- 30° (worm milling) Shift travel= 34 mm (manual adjustment) 34 mm (CNC axis) Collet/retraction mandrel W 20 Max. speed of workpiece spindle 770 rpm. Milling spindle drive 0.55 kW Max. milling spindle speed 8000 rpm Axis drives = X-axis (plunging) / travel 80 mm via CNC Z-axis (longitudinal feed) / travel 190 mm via CNC C-axis (workpiece axis) via CNC Rapid traverse = X-axis 6000 mm/min. Z-axis 6000 mm/min. Hydraulic unit 0.37 kW

Condition: used, Year of construction: 1987, max. wheel diameter 150 mm max. module 5 min. module 0,5 weight of the machine ca. 10.000 kg Itsdox U A Umspfx Ag Usb dimensions of the machine ca. 6500 × 2700× 3600 m

Condition: used, Year of construction: 1986, max. wheel diameter 150 mm max. module 5 min. module 0,5 weight of the machine ca. 10.000 t dimensions of the machine ca. 6500 × 2700× 3600 m Itsdpfoucgw Rex Ag Uob

Condition: used, Year of construction: 1988, max. wheel diameter 150 mm gear width . mm max. module 5 min. module 0,5 Control . total power requirement . kW Itsdpfxjwhq Eas Ag Uob weight of the machine ca. 10.000 t dimensions of the machine ca. 6500 × 2700× 3600 m

Condition: used, Year of construction: 1998, max. wheel diameter . mm gear width . mm max. module . Iedpfoucgwwox Ag Ustb min. module .

Condition: used, Year of construction: 2001, Control SIEMENS table surface area 160 mm Itsdpjudc S Tsfx Ag Ujb weight of the machine ca. 10 t

Condition: used, Year of construction: 1990, total length: 5,900 mm, total height: 2,000 mm, total width: 1,300 mm, Empty weight: 7.500 kg Itedpoxz Du Sofx Ag Ujb Price: On request Center-height: 250mm Table-length: 2300mm Travel grinding-spindel: 200mm Gear diameter: 300 mm Module range: 0.5 mm – 8 mm Helix angle: ±35° Max. workpiece weight: 100 kg - Year: 1990 - Documentation available: No - CE certificate present: No - Serial number: 018.0402 - Control type: Optronic CNC D140 - Control: CNC - Transport dimensions: 5900mm x 1300mm x 2000mm (l x w x h) - Transport weight [kg]: 7500kg - Transport packages [pcs.]: 5 Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Lukas van Rossum

Year of construction: 1940, condition: used, Automatic universal hobbing machine for the production of spur gears worm gears Largest milling diameter 120 mm Smallest milling diameter 5 mm Smallest tooth pitch module 0,30 Largest tooth pitch 2 mm largest milling length 100 mm with all accessories Itedpfx Agjkw T Rme Usb

Condition: used, Year of construction: 2004, workpiece diameter 125 mm module 4 control SIEMENS SINUMERIK travel -x axis 105 mm travel -y axis 40 mm travel -z axis 500 mm Iodpfsx Szm Asx Ag Uetb workpiece diameter 17 - 39,5 mm workpiece height 6 - 15 mm Gear Honing Machine | GLEASON-HURTH - ZH 125 The machine is in very good condition. Please note that the technical details were added from comparable machines. - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - #Tags: ZH125 | ZH-125

Condition: used, Year of construction: 1986, max. wheel diameter 150 mm Itsdpfx Agoxzuzij Usb max. module 5 min. module 0,5 weight of the machine ca. 10.000 t dimensions of the machine ca. 6500 × 2700× 3600 m

Condition: used, Year of construction: 1989, max. wheel diameter 150 mm Iodewhq Egepfx Ag Uetb max. module 5 min. module 0,5 weight of the machine ca. 10.000 kg dimensions of the machine ca. 6500x 2700x 3600 m

Condition: used, Year of construction: 1987, max. wheel diameter 150 mm gear width . mm Ijdewhq Afspfx Ag Ustb max. module 5 min. module 0,5 Control . total power requirement . kW weight of the machine ca. 10.000 t dimensions of the machine ca. 6500 × 2700× 3600 m

Condition: used, Year of construction: 1998, max. wheel diameter 85 mm gear width max. 125 mm max. module 3 Iedpfxswhqx To Ag Ujtb Control ja total power requirement 30 kW weight of the machine ca. 8 t

Condition: used, Year of construction: 2005, weight of the machine ca. 7.800 kg dimensions of the machine ca. 3.380 x 3950 x 3015 m Iodpfxjudc S Hj Ag Uotb

Condition: excellent (used), Year of construction: 2018, max. wheel diameter 360 mm gear width 210 mm Isdpfjx E Dupsx Ag Uetb max. module 7 min. module 0,5 Control Burri weight of the machine ca. 9,5 t Machine in top condition! (Original Reishauer RZ 362A) Extensive accessory package including BC2 loading/unloading unit and filtersystem. Direct drive in grinding and workpiece spindles, linear guides, ball screws and Heidenhain linear scales in all axes. Reports and inspection under power available upon request!

Condition: good (used), Year of construction: 2008, max. workpiece diameter 300 mm ca. 6 mm hob turning speeds 90-900 U/min Size of table plate Ø 300 mm table turning speeds 135 U/min Torque max. 445 Nm voltage 400 V total connected load ca. 50 kVA weight of the machine ca. 10,5 t dimensions of the machine ca. 3,5x2x3,0 m Gleason-PFAUTER GP 300 CNC gear hobbing machine for gear cutting on shaft-shaped and wheel-shaped workpieces with all rollable profiles and shapes occurring regularly around the circumference of cylindrical workpieces. In the basic version for wet milling with cooling lubricants or as an option for dry milling. Iedpfxex Ti A Is Ag Uetb SIEMENS SINUMERIK 840 D motion control system with 5 axes and 1 spindle (basic configuration) as well as electronic gearbox (EG) and integrated safety functions. * 19" flat control panel OP 012 with - integrated PC system PCU 50 with Windows XP operating system Smallest/largest distance between cutter and workpiece axis - 30/230 mm Largest axial slide travel - standard version 250 mm Max. cutter dimensions - diameter 140 mm + length 220 mm Swivel range of the milling head +/- 45° Maximum cutter travel 200 mm Cutter arbor taper HSK-B80 (Hollow shaft taper according to DIN 69063) Includes 32 mm milling mandrel

Condition: good (used), Heavy-duty transport rollers, machine rollers, transport trolleys, heavy-duty trolleys, tank rollers, machine transport rollers steering gear -Manufacturer: Jung, Machine transport roller: Steering mechanism type JL 12 K -Load capacity: 12 t (with chassis approx. 24 t) -Support surface: Ø 170 mm -Support height: 110 mm -Chassis: 4 transport rollers in stock can be supplied for an additional charge, see ID 35936 -Transport dimensions: 970/950/H260 mm -Weight: 67 kg Itsdpfjww Uzkex Ag Uob

Year of construction: 2025, condition: as good as new (ex-display), Universal testing machine PM10 Force: 10 kN cross beam stroke: 700 mm Installation space: 400 mm total height: 1230 mm Weight: ca.85 Kg Travel resolution: 0.01 mm Itjdpfxod R Dpmj Ag Ujb testing speed: 1-500 mm / min Return speed: 700 mm / min Force transducer: 10kN incl. evaluation electronics and basic software. Our testing machines can be operated in stand-alone mode via a numeric keyboard, so that a "quick test" can be carried out without a PC. For tests that require data storage and recording of the curve progression, we offer you the possibility of control and evaluation with the basic software. This allows to generate different test sequences and to create a test protocol. Furthermore, you have the possibility to process the raw data in your own programs. Optional: - Delivery & commissioning -DAkkS or factory calibration according to DIN EN ISO 7500-1 - Clamps: Pressure plates, bending devices, shearing devices, wedge clamps, shear clamps, peeling clamps, screw clamps, pneumatic clamps and hydraulic clamps.