Used Emco E 25 for sale (138)

Condition: good (used), Hardness tester functional Bwjdpfx Adjxr Atbjxsw

Condition: excellent (used), Year of construction: 2023, Work Area Longitudinal slide travel (X) 350 mm Cross slide travel (Y) 250 mm Usable vertical slide travel (Z) 300 mm Distance spindle nose – table surface (min.-max.) 120 – 420 mm Milling Table Bwsdpfow N Nvlex Adxow Cast iron table, ground Clamping surface (LxW) 520 x 300 mm Table surface height above floor 900 mm Max. table load 100 kg Number of T-slots 5 T-slot size acc. to DIN 650 12 mm T-slot spacing 45 mm Milling Spindle Speed range – direct drive 0 – 10,000 rpm (Three-phase asynchronous motor) Torque (100/60% DC) 33 / 41 Nm Power (100/60% DC) 7 / 8.5 kW Tool holder per DIN ISO 69871-A SK 30 Pull stud per DIN ISO 69872 (similar to 7388/2) M12, Type A Tool holder balanced G2.5 (per DIN ISO 1940, at 10,000 rpm) Slide Drives (Servo Motors) Feed rate in X / Y / Z 24 m/min Rapid traverse speed in X / Y / Z 24 m/min Feed force in X / Y / Z 3000 / 3000 / 4000 N Mean positional scatter per VDI 3441 in X / Y / Z 4 / 4 / 4 µm Tool Magazine Tool changer based on S-arm principle with random management Number of tool stations 20 Direct tool change time 2.5 s Max. tool diameter Ø 63 mm Max. tool diameter with adjacent slot empty Ø 80 mm Max. tool length 200 mm Max. tool weight 5 kg Clamping force 1500 N Max. total tool magazine load 60 kg Coolant System (Option) Coolant supply at milling spindle via 3 nozzles Tank capacity (standard) 140 l Delivery pressure at 50 Hz 3.5 bar Flow rate at 3.5/1 bar 15 / 65 l/min Pneumatics Supply pressure 6 bar Connection line Ø 10 mm Supply volume 50 l/min Compressed air quality per DIN ISO 8573-1 Purity class 4 Lubrication System Main spindle bearings Lifetime grease lubrication Guideways automatic central oil lubrication Feed screws automatic central oil lubrication Electrical Connection Power supply 3/PE 400~ V Max. voltage fluctuations +10 / -10 % Frequency 50 / 60 Hz Machine connected load 9 kVA Max. main fuse for machine 20 A gG Required short-circuit power 700 kVA Dimensions / Weights Overall height 2200 mm Installation area (WxD) (excluding coolant and options) 1600 x 1710 mm Total machine weight 1970 kg (excluding coolant and options) Coolant tank (standard, empty) 60 kg Chip Conveyor Hinged belt conveyor for wet and dry machining Discharge height 500 mm 4th Axis / NC Rotary Table Resolution 0.01° Max. speed 44 rpm Max. torque 20 Nm

Condition: used, functionality: fully functional, EMCO Lathe Maximat V13 380 Volt Serial No.: D1E8706022 MB No.: 99826 Condition: used Location: 86928 Hofstetten Price: €8,900 net Bwjdpfjv H Uklsx Adxsw

Condition: good (used), Year of construction: 2000, Emco Emcoturn 365-65, Year of manufacture 2000, Siemens 810 D control system, X/Z travel 210/610 mm, 12-station VDI 30 turret, all stations driven, driven tools up to 4,000 rpm, collet chuck, tailstock, C-axis 0.001°, spindle speed up to 6,300 rpm, coolant system, chip tray, accessories, Bodpfx Aswd E N Sjdxeww Machine has exclusively machined aluminum and brass, Machine is available at short notice.

Year of construction: 2006, condition: ready for operation (used), Control Unit Brand SIEMENS Model Sinumerik 840D Main Drive Number of spindles 2 Spindle speed range 6300 Spindle motor power 10 KW Number of axis 4 Media Chip conveyor Yes Additional Equipment Emco standard bar feeder interface Bodpexmbypofx Adxeww Oil mist separator 2 coolant pumps for spindle flushing 2 high-pressure coolant pumps (10 bar) Parts ejector with flushing through counter spindle Short bar feeder This 4-axis EMCO TURN 332 MCPlus was manufactured in 2006. It features a CNC lathe with a drive power of 10 KW, main spindle speeds up to 6300 rpm, and counter spindle speeds up to 7000 rpm. Equipped with two 12-slot tool turrets VDI 25, it supports up to 24 driven tools. The machine includes a Sinumerik 840D control, chip conveyor, and a bar feeder for bars ranging from 6-45 mm in diameter. Contact us for more information. Application Types Turning

Condition: used, Technical Data: Centre height: 275 mm Distance between centres: 3000 mm Swing diameter over bed: 550 mm Swing diameter over cross slide: 340 mm Spindle bore: 105 mm Spindle nose: Camlock 8" Speed range: 0 - 2500 rpm Motor power: 19.5 kW Equipment: - CNC control FAGOR 8055 - 4-position turret head - 3-jaw chuck ø 315 mm - Steady rest Bsdpfx Adoxpgrpexoww

Condition: excellent (used), functionality: fully functional, EMCO Maximat Super 11 – Precision Lathe in Very Good Condition For sale is a used EMCO Maximat Super 11, a robust and precise universal lathe "Made in Austria." This machine is ideally suited for workshops, training centers, or demanding hobbyists who value quality and accuracy. The machine is pre-owned but well-maintained and fully operational. All gear shifts are smooth, the guides are in good condition, and the machine has been regularly serviced. Technical Specifications: Center height: 140 mm Distance between centers: 600 mm Spindle speed range: 55 – 2200 rpm (8 geared steps) Tailstock: MT2 taper Tool holder: Quick-change toolpost Lighting: Integrated LED work light Weight: approx. 360 kg Dimensions (L × H × W): approx. 1.3 m × 1.2 m × 0.6 m Condition & Accessories: Machine runs quietly with low vibration Tailstock is smooth and easy to adjust with high precision Quick-change toolpost included LED work light for optimal visibility Various clamping devices or tools can be purchased additionally upon request (by arrangement) Price: The price is within a reasonable range and negotiable. Bwsdexqx Nvepfx Adxjw Open for price discussions upon serious interest. Miscellaneous: Collection preferred, viewing by appointment possible Machine can be shown under power

Condition: like new (used), Year of construction: 2016, operating hours: 1 h, functionality: fully functional, machine/vehicle number: F16 163802, As-new CNC milling machine – first delivered in 01/2017. Never used, therefore in immaculate condition. Fully operational, can be inspected under power. No damage, no signs of wear. Siemens WinNC Sinumerik control system with a separate touchscreen monitor. Complete with matching base cabinet and coolant system. Various accessories included, also unused. Power connection for 230V. No delivery, collection only. Transport must be organized by the buyer. Assistance with loading may be possible. Bedpfoxrp Tuox Adxjww

Condition: excellent (used), Year of construction: 2019, functionality: fully functional, turning length: 300 mm, turning diameter: 200 mm, travel distance X-axis: 100 mm, travel distance Z-axis: 200 mm, total height: 1,600 mm, total length: 2,000 mm, total width: 1,000 mm, overall weight: 300 kg, Operating voltage: 230 V Bwsdpfxjw Ivvij Adxew Frequency: 50-60 Hz Rated current: 11 A Control: EMCO EASY 2CONTROL (HEIDENHAIN TNC 640, SIEMENS SINUMERIC 840) Turning length: approx. 300 mm Center height over bed: approx. 100 mm Travel: X: approx. 100 mm Z: approx. 200 mm The machine is equipped with a tailstock, a three-jaw chuck, a special tool turret including a mobile workbench and suitable accessories.

Condition: good (used), Year of construction: 1997, functionality: fully functional, feed length X-axis: 450 mm, feed length Y-axis: 300 mm, feed length Z-axis: 350 mm, 3-axes digital read out horizontal and vertical milling spindle quill Technische Daten / technical details: Längsweg X / X-travel longitudinal 450 mm Bodpfx Adowyit Hoxjww Querweg Y / Y-travel cross 300 mm Senkrechtweg Z / Z-travel vertical 350 mm Tischgröße / table size 800x400 mm Spindelaufnahme / spindle taper SK40 Drehzahlbereich / spindle speed 50-2500 UpM /rpm Vorschubbereich / feed range 8-400 mm/min. Antriebsleistung / power capacity 3,2 kW Gewicht der Maschine / weight 1500 kg Technische Daten, Zubehör und Beschreibung der Maschine sind unverbindlich - Technical data, accessories and description of the machine are not binding.

Year of construction: 2004, condition: ready for operation (used), Control Unit Brand SIEMENS Model Sinumerik 840D Bwjdpfx Adoxmby Asxjw Main Drive Number of spindles 2 Spindle speed range 6300 Spindle motor power 10 KW Number of axis 4 Table Number of tslots 12 Turret Number of turrets 2 Tool taper VDI 25 Media Chip conveyor Yes Additional Equipment Oil mist separator 2 coolant pumps for spindle flushing 2 high-pressure coolant pumps (10 bar) Parts ejector with flushing through counter spindle Bar feeder This 4-axis EMCO TURN 332 MCPlus was manufactured in 2004. It features a CNC lathe with dual spindles capable of speeds up to 6300 and 7000 rpm respectively, and two 12-slot tool turrets. Includes high-pressure coolant systems, a chip conveyor, and a bar feeder for efficient operation. Ideal for precision turning tasks. Contact us for more information about this machine. Application Types Turning

Condition: used, Year of construction: 2003, Emco lathe enco Turn 420 MC with bar loader Bwsdpfx Adounzgrjxsw condition see pictures

Condition: excellent (used), Year of construction: 1998, functionality: fully functional, Max. turning diameter: 185 mm Max. turning length: 186 mm Spindle bore: 73 mm Max. workpiece weight: 30 kg Control: SIEMENS SINUMERIK 840 C Including documentation Including chip conveyor Including LNS Quick Load bar feeder Bwodpfxexl Amno Adxew

Condition: good (used), Year of construction: 2009, Machine used only for plastic. thry spindle 95.mm Technical data shown on picture. 27.03.2025. With machine will come another spannpfutter with possibility 80 mm. Bwodpeu Ibnqjfx Adxow Parts shown by hand not come.

Condition: excellent (used), Year of construction: 2017, functionality: unexamined, machine/vehicle number: 173902, travel distance X-axis: 300 mm, travel distance Y-axis: 300 mm, travel distance Z-axis: 300 mm, total height: 1,500 mm, total width: 1,100 mm, total length: 1,400 mm, table width: 200 mm, table length: 600 mm, rotational speed (max.): 2,200 rpm, rotational speed (min.): 80 rpm, overall weight: 800 kg, input current: 16 A, - Operating voltage: 3 x 400 V - Frequency: 50 – 60 Hz - Number of table slots: 4 - Tool holder: SK 30 EQUIPMENT: Bedpfewdnz Dsx Adxoww - Three-axis digital readout (Heidenhain) - Collet set included

Year of construction: 1998, condition: ready for operation (used), Swing diameter over bed/cross slide: 430mm/210mm, distance between centers: 510mm, travel X/Z: 160mm/310mm, spindle speed: 6300rpm, rapid traverse: 20m/min, tool positions: 12, tool holder: VDI30. Machine dimensions X/Y/Z: approx. 2250mm/2000mm/2000mm, weight: approx. 2600kg, control: Fanuc Series 21-T, operating hours: approx. 40000h. The hour counter was reset after each repair. The machine has electronic issues that cause sporadic system failures. An on-site inspection is possible. Bwsdpfx Asxmkcajdxsw

Condition: ready for operation (used), Year of construction: 2005, operating hours: 25,217 h, General Data Measurements width 3400 mm Measurements depth 2550 mm Bwjdoxfcrdopfx Adxew Measurements height 2300 mm Machine weight 8500 kg Control Unit Brand SIEMENS Model 840D Main Drive Number of spindles 2 Spindle speed range 5000 Movement X-Axis Movement 280 mm, X-Axis Rapid Traverse 24 m/min Y-Axis Movement 100 mm +/-50 mm Y-Axis Rapid Traverse 10 m/min Z-Axis Movement Z/Z2/Z3=900/750/750 mm Z-Axis Rapid Traverse 30 m/min Workpiece Workpiece X 744 mm Table Tslots size VDI40 Turret Number of turrets 2 Number of tool slots 12 Motorized tools VDI40 stations (both upper and lower turret) Media Power consumption 46 kVA Internal cooling Yes General Data Measurements width 3400 mm Measurements depth 2550 mm Measurements height 2300 mm Machine weight 8500 kg Control Unit Brand SIEMENS Model 840D Main Drive Number of spindles 2 Spindle speed range 5000 Movement X-Axis Movement 280 mm, X-Axis Rapid Traverse 24 m/min Y-Axis Movement 100 mm +/-50 mm Y-Axis Rapid Traverse 10 m/min Z-Axis Movement Z/Z2/Z3=900/750/750 mm Z-Axis Rapid Traverse 30 m/min Workpiece Workpiece X 744 mm Table Tslots size VDI40 Turret Number of turrets 2 Number of tool slots 12 Motorized tools VDI40 stations (both upper and lower turret) Media Power consumption 46 kVA Internal cooling Yes This 7-axis EMCO HYPERTURN 665 MC PLUS lathe was manufactured in 2005. It features twin spindles, twin turrets, and a maximum turning diameter of 600 mm. Equipped with a SIEMENS 840D CNC, it offers spindle speeds up to 5000 rpm and a bar passage diameter of 65 mm. Additional features include a LNS MOVE bar loading magazine, high-pressure coolant system, and air-conditioned control cabinet. For more information about this lathe, please reach out to us. Application Types Turning

Condition: ready for operation (used), Year of construction: 1997, functionality: fully functional, machine/vehicle number: F4N K5 105, Emco FB5; year of manufacture 1997; accessories: sub-spindle head + approx. 10 pcs SK 40 tool holders; Prototrac control Bwjdpfexqf Ewex Adxew

Condition: like new (used), Year of construction: 2019, operating hours: 40 h, functionality: fully functional, feed length X-axis: 450 mm, feed length Y-axis: 350 mm, feed length Z-axis: 400 mm, spindle speed (max.): 5,000 rpm, quill travel distance: 80 mm, rapid traverse X-axis: 5 m/min, rapid traverse Y-axis: 5 m/min, rapid traverse Z-axis: 5 m/min, total height: 1,990 mm, total width: 2,030 mm, total length: 1,980 mm, table width: 270 mm, table length: 400 mm, type of input current: three-phase, rotational speed (max.): 5,000 rpm, rotational speed (min.): 10 rpm, table load: 450 kg, overall weight: 2,270 kg, input voltage: 400 V, workpiece weight (max.): 450 kg, input current: 16 A, input frequency: 50 Hz, Equipment: CE marking, documentation/manual, rotational speed infinitely variable, Immediately available stock machine from our Trencin (SK) showroom. (Sale reserved.) EMCOMAT FB 450 with Siemens Sinumerik 828D control system. DEMO machine in “AS NEW” condition, available for immediate delivery. (Sale reserved.) We are happy to provide you with an individual offer. Visit us and inspect the machine under power. Travel range: X450/Y350/Z400 mm Bodpfx Adexapdcsxoww Table size: 800 x 400 mm Drive power: 7/10 kW Infinitely variable spindle speed: 10–5000 rpm SIEMENS Sinumerik 828D Universal toolroom milling and drilling machine equipped with the modern Sinumerik 828D control system and hydraulic tool clamping. Travel range: X450/Y350/Z400 mm Drive power: 7/10 kW Spindle speed: 10–5000 rpm Feed rate: 10–2000 mm/min Rapid traverse up to 5000 mm/min Toolroom machine precision according to DIN 8615 Tool holder: DIN 69871 SK40 Includes: - Linear guides - Ball screws - Vertical milling head swivel ±90° with quill stroke 80 mm - Swivelling unit for vertical head - Hydraulic tool clamping - Coolant system - LED machine lighting - Fixed angle table 800x400 mm - Chip tray - Automatic central lubrication - Service tools - Documentation in Czech and English - Sinumerik 828D interface in Czech, German, English - 15" multi-touch display - Includes 3-axis control package with ball screws and servomotors - Machining cycles with graphic support: - Drilling, deep drilling, reaming - Tapping (with length compensation), on pitch circle and in a line of holes - Rectangular and circular pockets - Slot milling cycle - Measurement cycle - etc. - USB interface

Condition: excellent (used), Year of construction: 2006, functionality: fully functional, spindle bore: 50 mm, EMCO lathe EMCOMAT 17D ex education in very clean condition. Specifications: - year of construction 2006 - turning diameter over the bed 340mm - turning diameter over the cross slide 190mm Bwsdsu N Dpmspfx Adxsw - distance between centers 700mm - speed 40-3000rpm variable in 4 steps - diameter of main spindle 50mm Accessories: - 3-jaw chuck with inner and outer jaws - 3-axis digital readout - electric diagram - multifix chisel holder with 3 holders - cooling system - machine illumination - rotating center - bedstop - machine feet

Condition: excellent (used), Year of construction: 2019, functionality: fully functional, travel distance X-axis: 300 mm, travel distance Y-axis: 300 mm, travel distance Z-axis: 200 mm, mount diameter: 30 mm, total height: 1,800 mm, total width: 950 mm, total length: 2,000 mm, table width: 120 mm, table length: 420 mm, Operating voltage: 230 V Frequency: 50 – 60 Hz Rated current: 2.8 A Control: EMCO EASY 2 CONTROL (HEIDENHAIN TNC 640, SIEMENS SINUMERIC 840) Tool holder: presumably SK 30 Max. tool clamping length: 35 mm Bodpfx Aow Ivu Esdxjww Table dimensions: 420 x 120 mm With 2 T-slots and a special EMCO vise Jaw width: 60 mm Travel paths: X: approx. 300 mm Y: approx. 300 mm Z: approx. 200 mm Includes matching mobile workbench with various compatible contents Includes 7-position tool changer, collets, and various suitable tool holders

Condition: ready for operation (used), Emco emcomat FB4 Milling Machine CNC control over X and Y axes by Proto Trak Type AGE 2 Also usable in conventional mode. SK40 spindle taper Spindle speeds: 50-2500 rpm X-axis travel: 450 mm Y-axis travel: 300 mm Z-axis travel: 350 mm Bwedpoxc H I Refx Adxow Table length: 800 mm Table width: 400 mm Equipped with coolant system, emergency stop, and table guard with interlock.

Condition: ready for operation (used), Year of construction: 2014, Control Unit Brand SIEMENS Model 828 D Main Drive Spindle speed range 50-12000 Number of axis 3 Movement X-Axis Movement 900 mm X-Axis Rapid Traverse 24 m/min Y-Axis Movement 500 mm Y-Axis Rapid Traverse 24 m/min Z-Axis Movement 500 mm Z-Axis Rapid Traverse 24 m/min Table Outer length 1000 mm Outer width 520 mm Min distance between vertical spindle and table 100 mm Max distance between vertical spindle and table 600 mm Table load 800 kg Tools Slots in storage 20 Media Bwsdpjwn N Iyjfx Adxew Chip conveyor Yes Additional Equipment Rinsing gun Cooling medium tray 360l IKZ 15 bar This 3-axis EMCO EmcoMill E900 was manufactured in 2014. A vertical machining center featuring a Siemens 828D control, it offers a spindle speed up to 12,000 rpm and torque of 83 Nm. It has a travel distance of X 900mm, Y 500mm, Z 500mm, and a rapid traverse rate of 24m/min. The machine includes a chip conveyor, a 360l cooling medium tray, and a 20-tool magazine. If you are looking to get high-quality milling capabilities consider the EMCO EmcoMill E900 machine we have for sale. Contact us for more information. Application Types Milling

Condition: ready for operation (used), Year of construction: 2013, Emco emcomat FB-600 CNC milling machine in Nieuwstraat! Bwedpfxsxc H H Hj Adxow

Condition: ready for operation (used), Year of construction: 2007, turning diameter over cross slide: 190 mm, turning length: 700 mm, turning diameter: 340 mm, spindle bore: 50 mm, Emco EMCOMAT-17D Distance between centers: 700 mm Swing diameter over bed: 340 mm Swing diameter over carriage: 190 mm Spindle bore/pass-through: 50 mm Spindle speeds: 35–3000 rpm Bedpsxc H Dfefx Adxoww Infinitely variable speed adjustment between gear ranges. Equipped with longitudinal and cross feed. 2-axis digital readout on X and Z axes. Multifix quick-change tool post.