Used Die Casting for sale (5,996)

Condition: like new (used), functionality: fully functional, Year of construction: 2025, The system was manufactured for a customer project but was not put into operation due to a subsequent change in the installation requirements. The conveyor belt is in new condition and is immediately available. This provides the opportunity to purchase the system at a significantly lower price than the new price. Aluminum angle conveyor with substructure, including adjustable feet and machine feet for leveling uneven surfaces. Horizontal section: 750mm Rising section: 2,300mm Inclination angle at the bend: 60° Height of the horizontal section: 250mm Njdpfx Aozfi A Askiolh Conveyor belt length measured on the floor: 1,900mm Discharge height: 2,200mm Design: Aluminum construction - 2x profile reinforced 90x45mm - Full-surface wear plate, 2.0mm, galvanized Drive roller + deflection roller, S235 steel, welded and machined Ø100x520mm, crowned, shaft fixed with tension bearings Drive: Gearmotor, 0.55KW, speed 0.53m/sec Connection 230/400V, 50Hz, protection class IP54 Drive ready for connection up to the motor terminal box (Commissioning must be carried out by a qualified electrician) PU conveyor belt DM 10/2 0+005 PU including wave edge PU petrol matte Conveyor belt width: 500mm 2 pieces of wave edges, 50mm high, 25mm wide, high-frequency welded 21 pieces of T-40 studs, 300mm long, approx. 300mm spacing Belt material: 2-layer, particularly dimensionally stable in the transverse direction In the bend area, the belt is guided on both sides with 2 pressure rollers each. The belt is designed with a border-free zone of 70mm on both sides. Due to the wave edge on both sides, the usable width of the conveyor belt is reduced: Usable width: 300mm, as follows: (Top view) Transverse arrangement: 70+25+5+300+5+25+70mm Belt guidance via PVC wedge strip on the running surface, profile - 10x6mm - Including recess in the wear plate - Including sliding joints in the drive and deflection roller Inspection possible after consultation Price is net, plus 19% VAT.

Year of construction: 2023, condition: as good as new (ex-display), Aluminum angled conveyor belt with substructure including adjustable feet and machine feet for levelling horizontal range: 2,500mm Rising area: 800mm Lead angle in bend: 40° Total conveyor length: 3,100mm Discharge height: 700mm Height of horizontal: 320mm PU conveyor belt DM 10/2 0+005 PU incl. corrugated edge petrol matt Nljdpfjk Scxiox Akieh Drive: motor 0.55KW, speed 0.3m/sec Connection 230/400V, 50Hz protection class IP54 Drive etc. ready for connection, motor 2 pcs. corrugated edges 80x45mm 2-layer particularly laterally stable Usable width 370mm

Condition: used, functionality: fully functional, machine/vehicle number: 908108, fuel type: electric, Year of construction: 2009, Kama Pro Cut 53 (2009) with Mabeg M1/60/400 Suction head and Sidelay (2008) Fully operational and rarely used. Please message so a video of the machine operating can be provided. For cutting, creasing, perforating, kiss-cutting, cold embossing and Braille. Profitably even with small and personalised runs. Be it printed matter or packagings, offset or digital printing. Benefits • AutoRegister, aligns each sheet to a print mark • Multifaceted applications for the 530 x 400 mm format • Highest register accuracy (less than 0.1 mm) • Profitable finishing also of small runs • Clean cutting contours thanks to very few to no nicks • Moving upper table ensures gentle passage of the material • Space-saving design, requires only 4.5 m² Options • Motor-driven pressure control system (MPC) • Cutting pressure indicator on the display and automatic overload protection • Platen changing system (4+1 mm) • Module for hot cutting of plastic materials • Hot foil and hologram stamping module available for retrofitting Technical Features • Material: Paper, cardboard, plastics 80–800 g/m² • Maximum sheet size: 530 x 400 mm Nodpfxswh Tq Sj Akiolh • Minimum sheet size: 210 x 148 mm • Maximum cutting size: 530 x 390 mm • Minimum gripper margin: 10 mm • Height of cutting blades: 23.8 mm • Maximum machine performance*: 6,000 sheets/h • Maximum cutting pressure: 120 tonnes • Maximum stacking height (sheet feeder): 700 mm • Maximum stacking height (delivery unit): 500 mm • Dimensions: 2.60 x 1.75 m • Net weight: 3,000 kg * dependent on material, sheet size and die configuration. when using a cardboard kit (option) or single-sheet feeding. Technical data and figures are subject to change.

Condition: used, Year of construction: 2004, functionality: unexamined, machine/vehicle number: 105000, overall weight: 13,000 kg, Inotechno hydraulic press, 100-tonne capacity. Nlsdpfoz Tbnxsx Akieh

Condition: used, Year of construction: 2022, machine/vehicle number: T0616, with CNC control, manufactured by SODICK, type: LN2, travels: X-axis: 350 mm, Y-axis: 250 mm, Z-axis: 270 mm, with automatic tool changer with 4 tool positions, resolution: 0.0001 mm, work table (made of ceramic), size: 600x400 mm, max. workpiece weight: 550 kg, max. electrode weight: 50 kg, dielectric fluid capacity: 400 l, machine dimensions: 2080x1955x2350 mm, machine weight: 3200 kg, with CO2 extinguishing system, operating hours: 1690 h. Nedpfxjz Nhtme Akielh

Condition: ready for operation (used), functionality: fully functional, machine/vehicle number: 21839, type of input current: AC, punching force: 60 t, overall weight: 5,000 kg, machine base height: 1,560 mm, input voltage: 400 V, input frequency: 50 Hz, input current: 25 A, control cabinet width: 770 mm, control cabinet length: 570 mm, control cabinet height: 380 mm, Equipment: CE marking, Heidelberg SBGZ – Very Good Condition Heidelberg SBGZ cylinder printing machine, in very good condition and available for sale. The machine has been well maintained and carefully operated, It is in very good working condition and suitable for continued professional production. Machine Highlights Manufacturer: Heidelberg Model: SBGZ Machine type: Cylinder / Letterpress Format: approx. 560 × 770 mm Good condition Well maintained Carefully operated Nodez Hn N Iopfx Akiolh Limited operating hours Ready for continued professional use Inspection possible by appointment The Heidelberg SBGZ is a robust and proven cylinder machine suitable for a range of printing and finishing applications. Further technical specifications, photographs and additional information are available upon request.

Year of construction: 2016, condition: excellent (used), functionality: fully functional, machine/vehicle number: 116245, GM DC330 Digital die cutting machine/ converter Compact footprint Unwind Web guide Web width 330 In / Outfeed nip for tension control Magnetic die station 200z / 25inch to support die plates of 50mm to 520mm Distortion/ Dispro factor to handle other tooth size plates Re Reg mark reader to support the printed web Die-cut offset possible inline Lateral/ Cross movement possible Waste rewinder Njdoylpvdspfx Akiolh Slitting station with manual 7 air pressured V-knives Upper and Lower rewind with options of clock or anti clockwise rotation Label or meter counting Core mandrels/spindles of 25mm, 38mm, 44mm and 76mm x 2 Cold foil Self adhesive lamination Laminator unwind and rewind Silencer to reduce noise when using the lamination Full Flexo station Varnish tray, Picking roller, Anilox roller, Print roller included GEW UV lamp Min 6 bar air pressure required Machine Weight 1200Kg !! Available for immediate sale !!

Condition: ready for operation (used), Measuring plate / cast plate / layout plate / stand, type 4000x1500x1300mm incl. 2 x tailstocks -Plate dimensions L x W x H 4000x1500x1300mm -2 x tailstocks / center height 400mm -Adjustable feet -Total weight approx. 2500 KG Nlsdpfx Ae Aazgaskioh Errors and omissions excepted.

Year of construction: 2017, condition: excellent (used), functionality: fully functional, Hello, we are offering our 2017 Rabolini die-cutting machine/die-cutting system, which has been completely overhauled. The maximum die-cutting format is 100 cm x 140 cm, with a cutting force of 360 tons. Die-cutting principle: flat/flat. Weight of the machine: 8,100 kg. The die-cutting machine is located on the ground floor, on a well-accessible industrial concrete floor. Documentation, CE declaration, etc., are all available! The machine can be inspected and tested while in operation. We would be happy to assist with training and instruction on how to operate the machine. The machine is located in D-41751 Viersen and is available for inspection. If you have any questions about the machine, please do not hesitate to contact us. Nlsdpfx Akjzxufvsish

Condition: good (used), Erba Titan Model 3 die cutter Format: 830×1200 The machine is fully operational, ready for production. Titan is synonymous with power, it is the strongest machine in its class. Production Italy Format in frame 830×1200 mm Format of the press 855x1230mm Weight 6900kg Power supply 380V Number of cycles 900-1400/h Installed power 5.5 kW Equipment: Nsdpoz N Sf Tjfx Akislh – electromagnetic clutch and brake – control panel – 3 operating modes: single, continuous, with time delay on opening – central lubrication – additional safety guards and two pressure safety mats – service tools – hard sheet metal for the press

Condition: as good as new (ex-display), functionality: fully functional, Year of construction: 2021, Aluminum flat belt conveyor 1,600 × 300 mm – NEW from stock (year of manufacture 2021) For sale is a like-new aluminum flat belt conveyor in an industrial design. The conveyor comes from our stock, has not been used in production, and is therefore in very good condition. Thanks to its high-quality aluminum construction and powerful ELVEM geared motor, the conveyor is ideally suited for professional use in production, warehousing, packaging, mechanical engineering, and automation technology. Technical data: Year of manufacture: 2021 Condition: New from stock Conveyor length: 1,600 mm Belt width: 300 mm Robust aluminum profile construction Green PVC conveyor belt with cleats High-quality ELVEM geared motor Three-phase connection (400 V) Smooth and low-maintenance operation Application areas: Mechanical engineering Packaging technology Warehousing and conveyor technology Automation Assembly workstations Feeding of workpieces Nlsdpfozhx Duox Akijh Transport of individual parts, plastic, metal, or packaging components Advantages: ✅ New from stock ✅ Immediately available ✅ Robust industrial quality ✅ Low-maintenance aluminum construction ✅ High-quality industrial geared motor ✅ Compact design ✅ Ready for immediate use An inspection is possible at any time by prior appointment. Scope of delivery: Aluminum flat belt conveyor ELVEM geared motor PVC conveyor belt with cleats Net price, plus 19% VAT.

Year of construction: 2018, condition: used, functionality: fully functional, machine/vehicle number: Gießbank 533 MAP40, General Data: - Designed for wall-mounted toilets - Low-pressure casting process with level control - Suitable for multi-part plaster molds - 40 mold stations per unit - A total of 160 mold stations - Mold spacing: 700 mm - Modular operation in units of 10 molds each - Operation with 10, 20, 30, or 40 molds in use per unit is possible - Different casting times per 10-mold section are possible Production Capacity - For currently manufactured "married" toilet models: the upper and lower parts are cast separately -> Two castings result in a complete toilet. 160 castings per casting cycle -> 80 complete toilets per casting cycle. - For models without "marriage": one mold station corresponds to one product -> up to 160 pieces per casting cycle. - Dimensions: Installation area approximately length: 33,800 mm, width: 4,100 mm, height: 4,300 mm. Single-row roller conveyor with a length of approximately 33,000 mm. Four lifting beam systems per unit. Each lifting beam is designed for 10 molds. One extraction trolley per unit. - Casting and slip system: Slip supply DN 100, slip return DN 100, compressed air connection 2 inches for the pressure line, filling via high-level or level tanks, two level tanks per unit, two casting lines per level tank, return of excess slip to the return slip tank, flushing of the slip lines with water and compressed air, four separate flushing systems per unit. Nlsdpfx Akoz Ag Rroijh - Mold mounting and clamping technology: Steel base frame, four lifting beams with electromechanical cable winch drive, cable breakage and cable slack protection, divisible vertical clamping devices, upper clamping beams with quick-release fasteners, pneumatic clamping hoses. - Demolding and handling: Pneumatic extraction assistance, molds can be clamped and tilted by 90 degrees, mold halves are manually separated, ergonomic transfer of the green part to a roller conveyor, two-hand safety control, quick-change system for different mold mountings, track for existing vacuum lifting system. - Compressed air and low-pressure system: Separate compressed air distribution for each 10 molds, three compressed air circuits (upper clamping beams and core boxes, vertical clamping devices, separation of the green part and mold), individual pressure control via pressure regulators, pressure monitoring of the clamping circuits, acoustic signal in case of insufficient clamping pressure, low-pressure system for stabilizing the green part in the mold and for hose drying after flushing. - Drying, ventilation, and lighting: Fans for drying the parts, diameter approximately 950 mm, LED lighting strips along the unit, active unit sections can be visually marked by the lighting, uniform drying of the plaster molds supports up to two casting cycles per day. - Electrical system and control: Two main switch cabinets, one main switch cabinet controls 20 molds and two lifting beams each, two-hand operation for safety-relevant movements, separate control cabinets on the level tanks and lifting beams. - Advantages: High production flexibility due to the 10-mold division, different products or casting times within one unit are possible, unused conversion components remain on the unit, suitable for different toilet models and production concepts, modular design facilitates partial occupancy and adjusted production quantities, extensive peripherals for casting, flushing, drying, demolding, and transport are available.

Condition: good (used), Heidelberg Cylinder KSB 40×57 Automatic die-cutter A very rare model on the market. The machine is ready to work, in very good technical condition. After inspection. Nlsdoz N Sftopfx Akish Suitable for die-cutting. Central lubrication. Format 40×57 cm Weight 3500 kg Power supply 380 V Includes two drawers of additional elements, frame, sheet metal for the cylinder, fillers and typographic locks.

Condition: excellent (used), Year of construction: 2017, operating hours: 12,300 h, functionality: fully functional, machine/vehicle number: 7846, travel distance X-axis: 455 mm, travel distance Y-axis: 300 mm, travel distance Z-axis: 300 mm, workpiece weight (max.): 800 kg, total height: 2,600 mm, total width: 2,160 mm, total length: 2,600 mm, table width: 400 mm, type of input current: three-phase, distance table to quill: 450 mm, table length: 820 mm, warranty duration: 6 months, feed rate X-axis: 5 m/min, feed rate Y-axis: 5 m/min, feed rate Z-axis: 15 m/min, input voltage: 400 V, overall weight: 2,800 kg, table load: 800 kg, input frequency: 50 Hz, Equipment: documentation/manual, EDM312MF30 + AWEX100/5 100 electrode positions 5 pallet positions 320x320mm Operating hours 12,300h Technical data: Nedpfx Aez I Symekijlh Travel ranges: 455x300x300mm Workpiece table 820x400mm Tank size 900x520mm Filling height 300mm Distance table/electrode holder 150/450mm Workpiece weight max. 800kg Dielectric fluid max. 700l Dimensions WxDxH 2160x2000x2610mm Machine weight 2500kg Mains connection 3/N/PE 400/230 50Hz Power consumption 6.7 kVA Equipment: Color: Light/Gray Control interface MF30 V3.2 Touch screen display Generator, exogenous 60A Direct measuring system in all axes Cartridge filter Cooling unit integrated CO2 extinguishing system C-axis 100/min., holding brake Manual control panel with accept button Lowering tank, automatic positioning Chuck Erowa Warranty 12 months Transport Commissioning on site Training

Condition: excellent (used), Year of construction: 1962, Ref: 11154 . 1962 Heidelberg SBG Cylinder Professionally converted for precision die cutting and creasing applications. Features: For die-cutting / creasing in packaging and commercial finishing Used for carton production, creasing, embossing, or die-cutting Cylinder mechanism ensures consistent pressure distribution Ideal for materials such as cardboard, paperboard, and synthetic substrates Highly efficient, accurate and durable Long-term mechanical reliability. Comprising; Single sheet suction feeder Spring loaded gripper action Chain delivery 2 Standard chases. Specification: Max sheet size: 570 × 770 mm Min sheet size: 210 × 280 mm Max. impression area: 530 x 760 mm Speed: Max. 4,600 sheets/hour Machine size (L×W×H): 3,500 × 2,000 × 1,850 mm Nljdoz Ek Nuepfx Akijh Net weight: 5,850 kg

Year of construction: 2019, operating hours: 7,400 h, condition: excellent (used), Pwer Register 2 New SMart Feedeer 2 Elevated 400 mm. Nljdpe Ad I Ulsfx Akioh Format max. 76x106 cm Format min. 35x40 Max speed 8,000 f/h Minimum 70 g/m2 paper Cardstock max 2,000 g/m2 Corrugated cardboard up to 4 mm. Hours worked 7,300 Bernoulli device Available Febr. - March 2027

Condition: excellent (used), Year of construction: 2022, operating hours: 20,771 h, functionality: fully functional, travel distance X-axis: 1,010 mm, travel distance Y-axis: 1,510 mm, travel distance Z-axis: 700 mm, overall weight: 12,500 kg, For sale: Ingersoll Gantry 1200 Nedpfe Accv Ujx Akielh Year of manufacture: 2022 Machine table size: 1630mm x 1130mm Maximum table load: 7500kg Electrode changer: 30-position Total weight: approx. 12000kg Maximum bath height: 650mm minus 40mm FCS plate (not included in the price) Dielectric fluid height max. 610mm

Condition: good (used), Ram punch AMC Hydromatic 220 Label die cutter A professional machine made in Italy. AMC is a world leader in the production of label die-cutting machines. Very good condition. The machine is 100% functional and ready for production. This is the model currently in production. Technical specifications: Maximum format: 220 x 220 mm Number of cycles: 18/min Productivity: 900,000 sheets/h Weight: 700 kg The machine is equipped with a hydraulic quick-action unit. Photo safety barriers. Adjustable feed table in all directions. Two operating modes: semi-automatic and manual. Nljdpfx Aksz Dtbwsish Tail on the delivery.

Condition: new, Year of construction: 2024, operating hours: 10 h, functionality: fully functional, machine/vehicle number: WFB2500x2400, conveyor belt length: 4,900 mm, conveyor belt width: 290 mm, conveyor belt speed: 400 mm/s, total length: 4,200 mm, total width: 540 mm, total height: 2,000 mm, overall weight: 250 kg, discharge height: 2,000 mm, power: 0.55 kW (0.75 HP), type of input current: three-phase, input voltage: 400 V, input frequency: 50 Hz, motor manufacturer: GEMOTEG, Equipment: type plate available, Complete solution for conveying bulk material such as wood chips, wood pellets, shredded material, granulate, etc. Aluminum angled conveyor belt incl. substructure Horizontal area 2,500mm Rising area 2,400mm Angle in bend 45° Feed height: 300mm Discharge height 2,000mm Total conveyor belt length measured on the floor: 4,200mm Conveyor belt width 500mm Nlodpfx Akjrwi D Eoieh PVC conveyor belt incl. cleats and corrugated edge Drive: Motor 0.55KW Speed approx. 0.3-0.5m/sec Connection 400/240V, 50Hz Protection class IP54 Drive etc. ready for connection, motor control optional 8x adjustable machine feet for alignment Shaft edge: 50x35mm 25 pcs. T-40 cleats - 396mm pitch 2-ply especially transversely stable Useful width: 290mm, results as follows: Queranordnung 70+35+290+35+70mm ONLY WHILE STOCKS LAST!!! All our prices are net prices plus VAT. - can also be viewed under power after consultation!

Condition: good (used), Year of construction: 1991, functionality: fully functional, CNC sinker EDM machine MAHO HANSEN, Type: HS 500 E, Year of manufacture: 1991, with electrode changer (without electrode holders) and accessories. Nledpfxozcmans Akish Control system: EROCOM 20 (Heidenhain). Technical data: see data sheets. From a toolmaking department; all documentation available, in good condition.

Condition: good (used), Year of construction: 1995, CNC Wire EDM Machine AGIE AGIECUT 270 SF+F HSS Year of manufacture: 1995 Nlodpszzyhnsfx Akish Travel in X-axis: 350 mm Travel in Y-axis: 250 mm Travel in Z-axis: 256 mm Travel in U/V axes: ±70 mm Positioning resolution: 0.0001 mm Positioning accuracy: approx. ±3 µm Machining data Max. taper: 30° at a workpiece height of 100 mm Surface finish: up to approx. Ra 0.2 µm with multiple finishing passes Workpiece data Workpiece size, max. dimensions: 750 × 550 × 250 mm Workpiece weight, max.: 450 kg Wire system Wire diameter: 0.10 – 0.33 mm Wire speed: up to approx. 3 m/min Wire tension: CNC-controlled MACHINE DETAILS Control system: AGIEVISION / AGIE HSS Generator: AGIE HSS Mains connection: 3 × 400 V, 50 Hz Connected power: approx. 10.5 kVA Dimensions & Weight Dimensions (L × W × H): approx. 2,215 × 2,215 × 2,220 mm Machine weight: approx. 3,600 kg EQUIPMENT Fully automatic wire threading

Condition: good (used), Year of construction: 1995, NC sinker EDM machine AGIE AGIETRON INTEGRAL 2 Year of manufacture: 1995 Nlsdpfxezzyhue Akijh Travel in X: 350 mm Travel in Y: 250 mm Travel in Z: 350 mm Rapid traverse: approx. 720 mm/min Axes: 4 (X, Y, Z, C) Work area Table size: 600 × 450 mm Maximum workpiece dimensions: approx. 860 × 620 × 350 mm Maximum workpiece weight: 400 kg Maximum electrode weight: 100 kg Internal dimensions of the work tank: approx. 830 × 590 × 350 mm Distance from table to quill: 170 – 520 mm MACHINE DETAILS Control: AGIEMATIC T Generator: AGIEPULS 60 Power connection: 400 V / 50 Hz Dimensions & Weight Dimensions (L x W x H): approx. 3,000 × 1,700 × 2,580 mm Machine weight: approx. 2,550 kg

Condition: excellent (used), Year of construction: 2011, Control PC-NC Dialog Travel paths X/Y/Z: 1000/1510/700 mm C-axis 30-way electrode changer Hirschmann clamping system Support surface WxD 1140/1640 mm Load capacity 7500 kg Nedpj Adl Ntefx Akijlh Filter system Fire extinguishing system

Condition: like new (used), Year of construction: 2019, Ref: 11072 . 2019 Horizon RD-4055 Dual Cylinder Rotary Die Cut System Like new, ex demo condition - ONLY 5,000 on the counter! Efficient production with new separator and card stacker for labour saving operation. Features: • Die cutting, waste separation and stacking in one pass for efficient production. • A wide range of applications can be processed such as business cards, greeting cards, labels and light packages. • Maximum 6,000 sheets can be processed. • 21-up round corner business card production can processed at 126,000 cards per hour. • Simple and easy operation without relying on a skilled operator. • Uniquely designed servo motor controlled ‘Repeat-cut’ feature allows multiple-up cuts from a single up die to minimize die cost. • Ruggedly constructed yet compact compared to normal die cutters. Nodpfoymmqzjx Akislh • Various delivery options are available to process a wide range of applications. • Die-cutting and Kiss cutting can be performed simultaneously by using a die which has two different blade heights, ideal for making stickers and labels. • Creasing can be achieved to avoid image cracking. Suitable for boxes, pocket folders and greeting cards which require additional folding processes after die cutting. • Repeat-cut enables the running of multiple up imposed applications with a smaller die to reduce die cost (Up to 8 repeats) Equipped with: TOUCH PANEL: Both setup and control can be done through the intuitive touch screen. After mounting the upper and lower die, the system can be set up by simply inputting sheet size and product size. The graphical illustrations on the screen are simple and easy to understand. FEED SECTION: Vacuum belt feeding enables superior feeding with easy setup and operation. An ultrasonic sensor is used for double feed detection on a wide range of substrates. The optional code reader BR-N4055 enables job separation for easy handling. TRANSPORT SECTION: Sheets are registered by vacuum belt and position is firmly secured with gripper rollers for accurate and consistent register. Servo motor driven gripper rollers ensure the die cut position without effecting processing speed. The optional alignment detection sensor ADS-N4055 detects the alignment error for additional quality control. DIE CUTTING SECTION: Rigid magnetic upper roller and solid lower anvil cylinder ensure high quality die cutting. Uniquely designed die cutting section enables easy and quick die setting. Specification: Sheet Size (Before processing): Max. W400 x L550 mm or W15.740" x L21.650" Min. W200 x L275 mm or W7.875” x L10.830” Processed Material: Normal paper, Coated paper, Cardboard Material Thickness: 127.9 to 400 gsm Die Cutting: Max. 0.5 mm or 0.019” (In case of blade height: 0.8 mm or 0.031”) Max. 0.3 mm or 0.011” (In case of blade height: 0.6 mm or 0.023”) Creasing: Max. 0.4 mm or 0.015” (In case of blade height: 0.8 mm or 0.031”)

Condition: good (used), Simplacutter model IV 110×160 Cauhe die cutter The machine is fully operational, like new. Made in Spain. Frame size: 1100×1600 mm Sheet size: 1160×1680 mm Weight: 8500 kg Power supply: 380 V Installed power: 7.5 kW Impact force: 350 t Nedpfxoz Dtb De Akielh Equipment: – pneumatic clutch and brake – control panel – two frames – 2 operating modes: time-delayed, manual – central lubrication – additional safety guards – safety pressure mats – operating tools – hard sheet metal