Used Baler for sale (233)

Condition: reconditioned (used), Year of construction: 2005, operating hours: 30,408 h, functionality: fully functional, pressing force: 50 t, filling opening width: 1,100 mm, filling opening length: 1,250 mm, bale width: 1,100 mm, bale height: 720 mm, bale weight: 550 kg, overall weight: 16,000 kg, oil tank capacity: 600 l, year of last overhaul: 2024, Technical data baler: Manufacturer Presona AB Type LP 50 EH1 Year of construction 2005 Operating hours 30,408 hours, as of April Number of pressed bales 198,059 as of April Pressing force main press 50 tonnes Specific pressing force 63 N/cm² Theoretical throughput capacity 530 m³/hour Throughput capacity under operating conditions 260 m³/hour Dimensions of feed chute 1,250 x 1,100 mm Bale chamber volume 2.2 m³ Bale dimensions 1,100 x 720 mm, variable length Drive power 22 kW Tying 5-fold vertical, fully automatic Throughput rates with a bulk density of 30 kg/cbm 6 up to 7 tonnes/hour Bulk weight of 50 kg/cbm 7 up to 9 tonnes/hour Bulk weight of 100 kg/cbm 11 up to 14 tonnes/hour Bale density (paper/newspapers) 400 to 550 kg/m³ Hydraulic oil tank capacity 600 litres Pjdpfx Amju Thhrspjpr PLC control Telemecanique TSX Micro Schneider Magelis control panel Effective transport dimensions excl. baler 8,125 x 2,300 x 3,000 mm (L x W x H) Transport weight press approx. 16 tonnes Condition of the baler: The machine was partial overhauled in our workshop and general maintenance work was carried out. After completion of the overhaul work, the press was tested during operation and is available for sale at short notice. The following overhaul work was carried out: General work: Machine cleaned, derusted, primed, partially painted Wire entry marks in the press channel feed-throughs welded shut and smoothed Hydraulic unit: Hydraulic oil tank emptied, tank cleaned, new oil filled Oil filter and air filter replaced Leaky oil sight glass on hydraulic oil tank replaced All hydraulic hoses replaced Electrics: English language installed in the programme menu Two key switches in the control panel replaced Control cabinet replaced Signal lamp on the control cabinet replaced Flaps end switch replaced Electrical system of the turbulator replaced, connected and tested Press ram: All four rollers removed from the press ram and replaced Main hydraulic cylinder dismantled, disassembled and partially overhauled, cylinder tube honed, complete seal set replaced, leak test performed All plastic wear pads on the press ram replaced Pre-press: Both bearings on the pre-press shaft replaced. Both hydraulic cylinders dismantled, disassembled and partially overhauled, both cylinder tubes honed, complete seal sets replaced, leak test performed. Scraper flap on the pre-press replaced. Binding system: Two complete needles with wire deflection rollers replaced Needles adjusted and set All wire deflection rollers in the needle heads replaced Drill fingers replaced Two drill shafts replaced All 8 wear plates on the Drillomat, under the drill fingers, replaced Scope of delivery: Only the baler will be sold. The documentation (Manual, CE-declaration, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: reconditioned (used), Year of construction: 2002, operating hours: 44,590 h, functionality: fully functional, pressing force: 200 t, filling opening width: 1,020 mm, filling opening length: 2,000 mm, bale width: 1,100 mm, bale height: 1,100 mm, oil tank capacity: 3,100 l, power: 150 kW (203.94 HP), year of last overhaul: 2025, Technical data baler: Manufacturer MACPRESSE EUROPA S.R.L. Typ 112 Year of construction 2002, partially refurbished in December 2025 Operating hours 44,590 hours, stand December 2025 Press power main press 200 tons Specific press capacity 16,5 kg/cm² Feed channel 2,000 x 1,020 mm Filling volume 2,65 cm³ Theoretic throughput rate 795 m³/h Bale size 1,100 x 1,100 mm, length variable Driving motor 2 x 75 kW Tying system 5-fold horizontal, full automatic Throughput rate at MSW approx. 48 up to 54 tons/h, depends on material Volume hydraulic oil tank 3,100 l Machine weight baler approx. 50,8 tons Scope of delifery: 1 piece baler MACPRESSE, type 111A 1 operating manual with CE declaration, electrical and hydraulic circuit diagram Podpfox Dnb Uox Ampopr Comments: The machine was serviced and partially overhauled in our workshop. The following work was carried out and parts replaced: • Hydraulic oil tank emptied and cleaned • Oil and air filters replaced • New hydraulic oil filled • All hydraulic hoses replaced • Press ram dismantled, broken down into individual parts, mechanics made operational • Front two main rollers replaced • Knives on the press ram replaced • Main hydraulic cylinder dismantled, disassembled, cylinder tube and piston rod checked, complete seal set replaced • Counter knife in the frame replaced • Knife gap adjusted to approx. 3 mm • Upper steel guide rails in the frame on the left and right replaced. • Worn press base cut out, base plate replaced with wear-resistant HARDOX steel. • Binding and twisting unit dismantled, broken down into individual parts, mechanics made functional, all twisting shafts and ball bearings replaced. • All wire rollers in the needle heads replaced • Wire knives cleaned and readjusted, chains greased and tensioned • All wire deflection rollers made operational • All door contact switches replaced • Wirbulator device dismantled, disassembled and made operational • General maintenance work carried out Finally, the press was subjected to a machine test in manual and automatic mode, see our video for the machine function test. The documentation (BA, CE, electrical/hydraulic circuit diagram) is complete. Viewing is possible by appointment. We accept no liability for the technical specifications or any errors.

Condition: reconditioned (used), Year of construction: 2009, operating hours: 22,029 h, functionality: fully functional, pressing force: 80 t, filling opening width: 1,000 mm, filling opening length: 1,400 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 600 kg, overall weight: 16,000 kg, power: 45 kW (61.18 HP), year of last overhaul: 2025, Technical data baler: Manufacturer Avermann Maschinenfabrik GmbH & Co. KG, Germany Type AVOS 1410-45/80 Year of construction 2009 Operation hours 22,029 hours, as of December 2025 Press power main press 80kN Specific press force 103,9 N/cm² Feed channel 1,400 x 1,000 mm Theoretic cycle time 12 sec Theoretic throughput capacity 300 m³/h Bale size 1,100 x 750 (w x h), the length is variable Drive power 45 kW Connected load 75 kW Tying system 4-fold, vertical, fully automatic Throughput capacity at a bulk weight of 30 kg/cbm approx. 6,0 t/h bulk weight of 50 kg/cbm approx. 10,5 t/h bulk weight of 100 kg/cbm approx. 17,5 t/h Bale weight with a bale length of approx. 1.2 m up to 600 kg, depends on material SPS controller Siemens S7-300 Operating panel pulsotronic Baler dimensions built up 8,610 x 2,400 x 3,835 mm (l x w x h) Transport weight baler approx. 16 t Special equipment: Wear-resistant floor made of HARDOX steel Special press ram for pressing ‘difficult’ materials and loose bulk materials with small grain sizes Control cabinet air conditioning Machine foot elevation 200 mm Remark: The machine was serviced and partially overhauled in our workshop. The following work was carried out and parts replaced: • Dismantling of the press ram, disassembly into individual parts, reconditioning of the mechanics, replacement of the following plastic wear plates and rails: o Plastic wear rails left/right under the press ram o Plastic wear rails left/right above the press ram o Plastic main wear plate (support plate) in the centre under the press ram • Steel guide rails on the left/right in the frame • Replacement of the entire base plate, four-piece, made of wear-resistant HARDOX steel • Wire inlet rails in the press floor newly welded and smoothed • Replacement of the counter blade, two-piece, in the frame • Adjustment of the blade gap to approx. 2.5 mm • Dismantling of the binding and twisting unit, disassembly into individual parts, loosening of the mechanics, replacement of all deep groove ball bearings and axial ball bearings on the twisting shafts, wire blades cleaned and readjusted, chains greased and tensioned Pedpfx Aex A U Ncompepr • Support roller in front of the twisting shafts replaced • All hydraulic hoses replaced • Oil filter and air filter replaced • Main hydraulic cylinder checked for leaks • The hydraulic oil is only one year old, has been chemically analyzed, is still in good condition, and has therefore not been changed but can continue to be used. • General maintenance work carried out Finally, the press was subjected to a machine test in manual and automatic mode; see video for the machine function test.

Condition: used, Year of construction: 2008, functionality: fully functional, machine/vehicle number: 58900538, input voltage: 380 V, total width: 1,200 mm, total height: 2,300 mm, overall weight: 470 kg, total length: 850 mm, filling opening width: 830 mm, bale width: 830 mm, bale length: 600 mm, bale height: 650 mm, opening width: 830 mm, transport height: 2,300 mm, Machine fully functional, but the press plate is deformed and needs to be straightened (see photo). The machine is sold together with strapping bands for bundling the bales and a sack truck for transporting the bales. Pick-up only, no delivery and no warranty. Podpfx Aoy Hlg Nempopr

Condition: used, Year of construction: 2005, total width: 1,300 mm, total height: 3,850 mm, total length: 2,200 mm, Empty weight: 1.250 kg Price: On request - Year: 2005 - Documentation available: No - CE marking present: Yes - CE certificate present: No - Serial number: 308 - Transport dimensions: 2200mm x 1300mm x 3850mm (l x w x h) - Transport weight [kg]: 1250kg - Transport packages [pcs.]: 1 Financial information VAT: The price shown is exclusive of VAT Pedpfx Ameyrtcuopjpr VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Yorick Diebels

Condition: used, Year of construction: 2005, total width: 1,300 mm, total height: 3,850 mm, total length: 2,200 mm, Empty weight: 1.250 kg Price: On request - Year: 2005 - Documentation available: No - CE certificate present: No - Serial number: 307 - Transport dimensions: 2200mm x 1300mm x 3850mm (l x w x h) - Transport weight [kg]: 1250kg - Transport packages [pcs.]: 1 Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Yorick Diebels Pedpfoym Uxtjx Ampopr

Condition: used, Year of construction: 1983, total width: 750 mm, total height: 900 mm, total length: 2,400 mm, Empty weight: 500 kg - Year: 1983 - Documentation available: No - CE certificate present: No - Transport dimensions: 2400mm x 750mm x 900mm (l x w x h) Pedpsxalyysfx Ampjpr - Transport weight [kg]: 500kg - Transport packages [pcs.]: 1 Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Yorick Diebels

Condition: good (used), Year of construction: 2002, functionality: fully functional, Vertical baler HSM VL 600, year of manufacture 2002 Technical specifications: Manufacturer: HSM Model: HSM VL 600 Year of manufacture: 2002 Pressing force: 60 t Ppedeyz Sa Sspfx Ampor Drive power: 7.5 kW Cycle time (idle): 37 s Filling height: 1130 mm Feed opening: 1150 x 735 mm Bale size: 1200 x 1100 x max. 1200 mm Bale weight: 550 kg Machine weight: 3575 kg Materials: Suitable for paper, cardboard, film, car tyres The baler is in good condition and has been inspected and tested. A demonstration video is available on our website or YouTube channel. Operating manual and CE declaration are included. Inspection, including under power, is possible at any time by appointment. Material tests with your own materials can be arranged on request and for a service fee. Please note: All technical details are based on information provided by the manufacturer. We do not accept any liability for the specifications or possible errors. This offer is subject to change, prior sale reserved, and may be withdrawn at any time. Inspections are available by arrangement. Sale is ex works, without warranty or guarantee, and against advance payment only.

Condition: good (used), Manufacturer: Mil-tek Model: 205 TS Machine type: Plastic press / Film press Operating pressure: 8 bar Test pressure: 11 bar Material container: 20 l Drive: pneumatic CE marking: present Podsyx Skrepfx Ampopr Quantity: 4

Condition: good (used), Year of construction: 2021, functionality: fully functional, pressing force: 58 t, Very good condition, fully functional, low operating hours, year of manufacture 2021, pressing force 58 tons. New price: seen for €19,500 Pressure cylinder has been dismantled for transport, inspection possible by appointment. Psdpfx Aeyzw U Ujmpjpr Further presses in stock.

Condition: good (used), Year of construction: 2001, functionality: fully functional, KAMPWERTH SHD 1600 horizontal baler, incl. 3 interchangeable containers 48000x2800x3000 Paper baler // Waste baler // Refuse baler Baler, 1 unit Pedpfxsxm Skre Ampepr • Type: Kampwerth SHD 1600 • Year of manufacture: 2001 • Unladen weight: 3,500 kg • 15 kW • Dimensions: 5000x2300x3700 mm (disassembled for transport) Container box for baler, 3 units • Year of manufacture: 2001 • Volume: 28 m³ • Unladen weight: 3,100 kg • Filling weight: 12,000 kg • Dimensions: 7000x2400 mm Location: Bielefeld

Condition: new, Year of construction: 2022, functionality: fully functional, machine/vehicle number: Machinenummer 230067.020, pressing force: 60 t, power: 45 kW (61.18 HP), operating pressure: 250 bar, Bollegraaf Recycling Solutions, the original manufacturer of this mobile Bollegraaf baler, hereby offers the following machine(s) FOR RENT ONLY: Year of construction: 2022 Weight excl trailer: 22.000 kg Mobile Baler Volume capacity m3/hr max. 365 334 321 301 Volume weight kg/m3 max. 15 30 50 80 Weight capacity T/hr max. 5.5 10 16 24 Bale weight 400 – 800 kg, depending on S.G. of material and bale length Bale length - adjustable Bale height - 720 mm Bale width - 1100 m Filling opening - 1100 mm x 1320 mm Max. size supply - 1500 mm x 1200 mm Pressure force ram - max 60 tonf. Pressure force pre-press flap - max 25 tonnes Cycle time - 18 seconds Motor - 45 kW Motor Twistomat - 2.2 kW Motor counter pressure pump - 1.1 kW Ppedpfjh I T Ibjx Ampor

Condition: ready for operation (used), Year of construction: 2008, Brand: HSM Model: V-Press 1160 plus Year of manufacture: 2008 Pressing force: 532 kN Voltage: 400 V Max. bale weight: up to 550 kg (depending on material) Pedpfx Asyyk Tzsmpepr Bale dimensions: 120 x 110 x 120 cm Machine weight: 2,403 kg Machine dimensions: 180 x 157 x 298.5 cm Filling opening: 119.5 cm × 65 cm Condition: very good! Video of the machine in operation available upon request.

Condition: ready for operation (used), Model: HSM V-press 1160 plus baler Pressing force (kN): 532 Bale weight depending on material: up to 550 kg Max. bale size (mm): 1200x1100x1000-1200 Dimensions L x W x H (mm): 1780x1150x2985 Power (kW): 7.5 Weight (kg): 2300 Ppsdpfx Amsra Nyuepor Year 2007-2010, price: 5800 EUR Year 2011-2013, price: 6000 EUR YEAR 2018 COSTS 6000 EUR We also have HSM V-press 1160 max balers from 2014-2015 available.

Condition: used, Year of construction: 2006, functionality: fully functional, Baler press for bundles approx. 400 kg. Manufacturer: HSM Model: HL 3521 Year of production: 2006 Condition: good Machine has undergone major service. Oil pump replaced. Oil cylinders refurbished. After agreement, can be sold and shipped immediately. Psdpsy A Hu Hsfx Ampopr

Condition: ready for operation (used), Year of construction: 2015, functionality: fully functional, machine/vehicle number: MM1007, bale length: 880 mm, bale height: 600 mm, pressing force: 500 t, Taurus shear baler model E 556.P, year 2015, in excellent working condition and complete with documentation. This machine is ideal for baling and shearing all types of ferrous scrap: profiles, sheet metal, bulky mixed scrap, and vehicles. Technical data Shearing force: 500 tons Shearing width: approx. 950 mm Shearing height: approx. 640 mm Box length: 5,600 mm Open box width: 2,400 mm Bale size (closed): Width: 880 mm Height: 600 mm Pjdpoy Iblwsfx Ampepr Features Soundproofed 125 HP diesel engine Operator cabin Radio remote control Complete documentation Machine ready for operation.

Condition: ready for operation (used), Baler Hsm 155 VL Bale dimensions L x W x H: 1100 x 700 x 700 - 950 mm Bale weight: 2000 - 250 kg (Cardboard) Technical data: L x W x H: 1470 x 940 x 2259 / 2439 mm Weight: 950 kg Pressure force 16 tons Power supply: 400 V (three phases) Motor power: 4 kW Bale ejector Hsm 155.1 VL baler pressure force 18 tons Price of Hsm 155.1 VL baler - 2600eur Hsm 155.2 vl baler pressure force 16 tons Price of hsm 155.2 vl baler - 2800eur Pjdpfx Ajra Nrmompopr

Condition: good (used), Year of construction: 1981, functionality: fully functional, Equipment: documentation/manual, Automatic channel baler BOA Continu 25 LB + conveyor belt. The baler is in good condition and has been regularly serviced. Recently, the Denison pump underwent a complete overhaul. Fully functional and in continuous operation. Please contact us for further information. Ppedjw S Tv Ujpfx Ampjr

Condition: reconditioned (used), Year of construction: 2005, functionality: fully functional, pressing force: 90 t, filling opening width: 1,620 mm, filling opening length: 972 mm, bale width: 720 mm, bale height: 1,100 mm, bale weight: 600 kg, overall weight: 32,000 kg, pressure: 300 bar, power: 110 kW (149.56 HP), BOA baler with double pre-press flaps available in fully refurbished condition. The machine is located at our workshop in Almelo and can be inspected by appointment. If required, a matching (new) conveyor belt can be produced. The machine is perfectly suited for baling various materials such as cardboard, paper, plastics, car tires, and RDF. The machine is equipped with a so-called refu-ram. This is ideal for baling materials such as plastic bottles and/or shredded RDF. Technical specifications: Drive: 2x 55 kW Pressing force: 90 tons Bale dimensions: 1100 x 720 mm Psdpfexbc U Djx Ampjpr Bale weight: approx. 600 kg (depending on material) Number of tying wires: 5 vertical

Condition: new, Year of construction: 2026, functionality: fully functional, The BTS-MF40 is the ideal waste baler for compacting your loose cardboard and plastic film waste into a bale of up to 40 kg. The baling press impresses with its ease of use, safe operation, it is ideal for small material volume and producing compact and easy-to-handle bales. By baling these valuable and recyclable materials you achieve a volume reduction of up to 90%, a significant saving on your disposal costs and you properly return the material back into the recycling cycle. Pressing force: 2 Ton Bale weight: up to 40 kg (material depending) Bale size: 600 H (var.) x 535 W x 460 D mm Machine size: 1756 H x 718 W x 644 D mm Machine weight: 187 kg Transport height: 1756 mm Loading aperture: 522 W x 490 H mm Cycle times: 20 seconds Motor: 1.5 kW 13 Amp Power supply: 220 - 240 V (1 phase) Noise level: 68 dB User-friendly lever control Bale trolley for easy bale removal Retainers to prevent material spring back Reel holder for strapping rolls A quality product „Made in Europe“ Suitable for compacting Cardboard Plastic film and foils Cans and light sheet metal containers Canisters and light plastic containers Clothes Light valuable materials Pjdpsvahudefx Ampepr Optional Extras Machine colour RAL Can crusher insert AUTO compaction cycles Strapping rolls Power supply 380 - 400 V (3 phase) Waste Baler, Waste Compactor, Cardboard Baler, Film Baler, Foil Baler, Packaging Plastic Film Foil, Bailer, Baling Press, Garbage Press, Trash Compactor, Baling Compactor, Paper Press, Waste Paper Press, Cardboard Press, Cardboard Compactor, Foil Press, Paper Baling Press, Waste Baler, Residual Waste Compactor

Condition: new, Year of construction: 2026, functionality: fully functional, The BTS-MF40 is the ideal waste baler for compacting your loose cardboard and plastic film waste into a bale of up to 40 kg. The baling press impresses with its ease of use, safe operation, it is ideal for small material volume and producing compact and easy-to-handle bales. By baling these valuable and recyclable materials you achieve a volume reduction of up to 90%, a significant saving on your disposal costs and you properly return the material back into the recycling cycle. Pressing force: 2 Ton Bale weight: up to 40 kg (material depending) Bale size: 600 H (var.) x 535 W x 460 D mm Machine size: 1756 H x 718 W x 644 D mm Machine weight: 187 kg Transport height: 1756 mm Loading aperture: 522 W x 490 H mm Cycle times: 20 seconds Motor: 1.5 kW 13 Amp Power supply: 220 - 240 V (1 phase) Noise level: 68 dB User-friendly lever control Bale trolley for easy bale removal Retainers to prevent material spring back Reel holder for 2 rolls of strapping A quality product „Made in Europe“ Suitable for compacting Cardboard Plastic film and foils Cans and light sheet metal containers Canisters and light plastic containers Clothes Light valuable materials Optional Extras Machine colour RAL Pedpfx Ameu Iwgvopjpr Can crusher insert AUTO compaction cycles Strapping rolls Power supply 380 - 400 V (3 phase) Waste Baler, Waste Compactor, Cardboard Baler, Film Baler, Foil Baler, Packaging Plastic Film Foil, Bailer, Baling Press, Garbage Press, Trash Compactor, Baling Compactor, Paper Press, Waste Paper Press, Cardboard Press, Cardboard Compactor, Foil Press, Paper Baling Press, Waste Baler, Residual Waste Compactor

Condition: as good as new (ex-display), Year of construction: 2024, functionality: fully functional, overall weight: 270 kg, warranty duration: 24 months, empty load weight: 265 kg, Robust and compact construction Ppjdpfx Asu Tqmdsmpjr High-quality components with a longer lifespan Above-standard productivity Adjustable bale height (three sizes) Automatic start for efficient compaction Bale trolley for easy transport Material selector for cardboard and plastic Full bale indicator and service indicator Compliance with EN 16500:2014 safety standards

Condition: used, Year of construction: 1988, working width: 2,000 mm, Price: On request Pjdjypczzspfx Ampopr Registration number: LFD-32-P

Condition: used, Year of construction: 1989, working width: 20 mm, Price: On request Registration number: LHJ-77-K Ppodjypczujpfx Amper Bale shape: Rectangular

Condition: not inspected (used), Year of construction: 1985, functionality: unexamined, machine/vehicle number: 0485.1184.463, outer diameter: 1,300 mm, No minimum price – guaranteed sale to the highest bidder! By placing a bid, you are obliged to collect the item within the designated period: either between 11/05/2026 and 13/05/2026 or between 18/05/2026 and 21/05/2026! Pedpfxsynkapo Ampepr TECHNICAL DETAILS Tank diameter: 1,300 mm MACHINE DETAILS Dimensions & Weight Dimensions (L x W x H): 2,000 x 1,500 x 1,800 mm Machine weight: 700 kg External reference: Pieper - Lot 5