Center Lathe

MONDIALE Celtic 14

Condition: used, Year of manufacture: 1980s/90s Technical data: Centre height: 185 mm Centre distance: 750 mm Turning diameter over bed: 370 mm Spindle bore: 36 mm Bed width: 250 mm Nwsdpfeydk Hhsx Adboc Speed range: 38 - 1600 rpm Tailstock taper: MT 3 Quill stroke: 110 mm Dimensions (W x D x H), approx.: 1950 x 900 x 1200 mm Weight, approx.: 800 kg Equipment: - 3-jaw chuck, make: Röhm, ø 200 mm - Quick-change tool post with 4 holders - Bed stop - Chip tray

Condition: used, Year of construction: 2003, machine/vehicle number: 1527, Used lead and feed screw lathe COLCHESTER Triumph VS 2500 Centre height: 195mm Distance between centers: 650mm Spindle bore: 54mm Infinitely variable speed: 14–2500 rpm Tailstock quill: MT5, coolant system, quick thread cutting device Digital readout: FAGOR NUP 300 TS-RS 1 x RÖHM 3-jaw chuck, 5-position stop drum, spindle stop, Nwodpfx Asx Hrumjdboc machine lamp, 1 x PARAT 4-way turret, 4 x PARAT tool holders, live centre and quick-action drill chuck. The machine is located at our premises in 71334 Waiblingen-Beinstein and is available immediately. Inspection of the machine is possible by appointment.

Condition: good (used), Year of construction: 1972, LZ Lathe Manufacturer: HEIDENREICH & HERBECK Type: 21RO Year: 1972 with Parat quick-change toolholder, 10 pieces, machine documentation, thread dial indicator, live center, 250 mm Forkardt chuck. Swing over bed: 430 mm Swing over cross slide: 255 mm Center distance: 1000 mm Turning length: 750 mm Spindle speeds: 19-2000 rpm, 5.5 kW motor Spindle bore: 56 mm Further technical data available in the data sheet Required space: Length 2900 mm, Width 1100 mm, Height 1300 mm, Weight approx. 1750 kg Nodpfx Adjt Ipi Iebowc Machine documentation available. Coolant system installed, chip guard/rear panel. The machine is in good condition and can be demonstrated under power.

Condition: used, Year of construction: 1970, Technical details: turning diameter over bed: 325 mm turning diameter over support: 150 mm turning length: 1000 mm turning length: plan: 165 / quer: 160 mm center height over bed: 200 mm length of gap: keine Kröpfung mm range of revolution per miute: 48 - 1.500 / 10 step U/min spindle bore of work spindle: 40 mm feeds:: längs: 0,021...2,34 / quer: 0,09...1,6 mm tailstock quill taper MT: 4 tailstock quill adjustment:: 125 mm total power requirement: 2,2 kW weight of the machine ca.: 1,0 t dimension machine xH: 2,1 x 0,7 x 1,2 m Nsdou Ixydspfx Adbewc Threading possible: Metric, Withwort and modular thread Equipment: - 3-jaw chuck Ø 200mm with internal clamping jaws - Multifix quick-change steel holder - Foot brake - Cooling water pump (exclusive feed) *

Condition: good (used), Year of construction: 1956, Heavy lathe, turning machine, lathe, center and feed screw lathe, center and feed screw lathe -Manufacturer: Weisser, lead screw lathe type PF200 -Turning length: 1340 mm Nedpfx Aetzf N Rjdbjwc -Turning Ø over bed: 420 mm -Turning Ø over support: 240 mm -Spindle bore: Ø 41 mm -Spindle speeds: 31.5 - 1400 rpm -Three-jaw chuck: Röhm Ø 250 mm -Accessories: incl., see photos -Tailstock mount: MK4 -Drive motor: 2.5/3.5 kW -Dimensions: 2670/1000/H1230 mm -Weight: 1450 kg

Condition: like new (used), Year of construction: 2013, functionality: fully functional, Ficep 1201 DE 601 Excalibur drilling machine for processing flat steel and profiles, equipped with a drilling unit that moves longitudinally. This machine has been fully cleaned and inspected. The drilling machine features a numerically controlled drilling unit with longitudinal movement (X-axis), adjustment range 0 - 15,000 mm, and an automatic tool changer with HSK A80 interface for 6 tool positions. Thanks to the 19 kW drill spindle drive, the machine is suitable for use with carbide drilling tools. Technical details: • Support for profiled and flat steel with guide rail and fixed table, total length 15 m • Mobile drilling unit for longitudinal positioning along workpieces • Horizontal drilling head with single drill spindle • Additional tool storage in the X-axis direction • Clamping system for securing materials • Position detection device • Maximum profile size: 1200 x 1200 mm • Number of drill spindles: 1 • Drilling diameter: 5 - 40 mm • Tapping: M6 - M30 Nsdpfev Iamzox Adbswc • Drill spindle speed: 180 - 3000 rpm • Holder: HSK A 80 • Tool changer: 1 x 6 For more information, please contact us.

Year of construction: 1970, condition: good (used), functionality: fully functional, Stenner RESAW VHL 48 manufacture Stenner UK S/N J2103 year 1970 (original photos coming soon) Principal Dimensions and data: Nodpfevuhumex Adbjwc Diameter of saw pulleys: 48"= 1220mm Width of saw pulley face-standard 5" (127mm) Width of saw pulley face-optional 5 1/2" (140mm) Maximum width of saw - standard 5 1/2" (140mm ) Maximum width of saw-optional 6" (150mm)A Minimurn length of saw 25" 8" (782mm) Maximum height of top saw guide above table 28" (710mm) Table height from floor level 31 1/2" ( 800mm 9 Overall height from floor level 9.1" ( 2770mm) Overall width 8.1" (2460mm) Speed of saw pulleys,r.p.m. 8,000 (2440m/min) Horse power range 30 kW Size of fast and loose pulleys 20"x6 1/2" Feed speeds, standard; f.p.m. or m/min. 0-140 (0-42.6m) Shipping Specification : Standard Machine : Net weight, lbs. 3583 kg The VHL 48 is a band resaw of advanced design embodying many new features resulting from a close study of user-operator requirements, and the necessity to provide fast and accurate sawing coupled with ease of operation, reduced operator fatigue, low maintenance, and increased safety. The design caters fully for these essential factors which contribute to a markedly high level of operating efficiency. The machine is primarily designed for the planning mill and joinery shops. The thin bandsaw gives the machine a high timber recovery rate; the loss due to saw kerf being very low. Compared with a circular radial-arm resaw, the VHL is faster, less wasteful, and uses less power for a given class of work general The VHL is made only as, a left-hand machine, i.e. the saw pulleys run in an anti-clockwise direction when looking in the direction of the feed. The drive is normally arranged to give a saw speed of 8,000 feet permin. (2440m l/min.) Main Drive The main drive is applied to the bottom saw pulley spindle which is prepared for vee belt, flat belt, or flat belt fast and loose pulleys to suit the proposed driving unit. Complete electric motor drives, up to 40 H. P. and for most current supplies can be provided; they include two vee pulleys, set of vee belts, belt guard, motor with slide rails, starter and a master stop button which is fitted to the machine base close to the sawyer's position. horizontal rollers The horizontal rollers are 6" (152mm) diameter and extend the full opening on the fence side and 6" (152mm) beyond the table on the open side; they are normally free-running idle rollers. They can be supplied hydraulically driven as optional equipment, either with the machine or after installation; the rollers are then driven in synchronism with the main feed rolls, by a separate motor. The drive is arranged so that the open-side roller at the outfeed end rotates in the reverse direction to facilitate the return of timber to the sawyer. The roller in front of the saw is moveable sideways to permit rapid saw changing.

Condition: used, Iron lathe Njdpfx Adjrdmm Djbjwc

Condition: new, Year of construction: 2024, Drilling and milling machine Kudu with CNC control and tool changer (3-axis) drilling and milling machine with movable processing unit - the table remains stationary, the drill head moves. The drilling machine can be used both manually and fully automatically. After each drilling process, the processing unit moves to the next drilling position fully automatically in the X and Y axes. Operation is kept very simple. The data can be transferred to the machine control using the file formats DXF./DWG. be carried out via a programming station. Alternatively, the system can also be programmed directly on the machine control. The system is very robust and consists of proven machine components. Technical data: • Measuring length: 6,000 mm • Total length: 8,050 mm • Stable machine base • Drilling head speed: up to 2500 rpm (standard version), is supplied with the right speed for your application. • Tool holder: SK 40 • Drive of the X, Y and Z-axes via servomotors • Rapid traverse in the X-axis: 20 m/min • Rapid traverse in the Y-axis: 5 m/min • Distance from upper edge of table to lower edge of tool holder 400 mm • Table width 480 mm • Working height: 1050 mm • Drilling diameter: 3 to 30 mm in St. 50 (depending on the tool) • Tapping: M4 - M30 (with compensating chuck) • Machining path in the Y axis: 300 mm • Tolerance in the X axis: + - 0.1 mm • Tolerance in the Y-axis: 0.06 mm • Tolerance in the Z-axis: 0.06 mm • Drill head drive motor: 5.5 kW • System weight: 2300 kg • System dimensions: 8050 mm x 3000 mm x 2388 mm (see layout plan) • Power connection: 32 A • Air connection: 8 bar • Protection of the system at the front via light barrier • Access protection at the rear, machine fence • Control touch screen panel 21.5", reinforced front glass • Easy programming on the Machine • Milling of long holes and circles • Lubrication takes place using a minimum quantity spray system • without material vices • Remote maintenance possible using Teamviewer (LAN interface) • Tool memory for drilling tools, with dimensions, speed • Simulation of work processes • Digital hand wheel Nwsdpefu Ivzjfx Adboc Your advantages • The surface of the workpieces is protected • Clear, graphic surface • Machining directly at the end of the workpiece is not difficult • 50% space saving compared to pushing machining • Chips are collected in the chip tray • Simplest programming & operation • Minimum quantity spray system (standard) • Programming errors are prevented by CAD /CAM excluded

Condition: new, bore capacity in steel (diameter) 13,0 mm Nwodpfexabb Hox Adbjc x-travel 300 mm y-travel 130 mm turning speeds 100 - 2500 U/min throat 165 mm spindle taper MT 3 MK table-size 490 x 120 mm diameter of hob 30,0 mm motor 230 Volt total power requirement 0,75 kW weight of the machine ca. 50 kg. dimensions of the machine ca. 520x500x740 mm Scope of delivery: - Key chuck 1 - 13 mm / B 16 - Drill chuck arbor MK 3 / B 16 - tightening spindle M 12 - Height-adjustable protective cover - operating key