Section bending roll shafts 360 mm

MG AR360

Condition: ready for operation (used), Swing diameter over bed/cross slide: 650mm/430mm, distance between centers: 3000mm, bed width: 450mm, max. workpiece weight: 1800kg, spindle speed: 2000rpm, rapid traverse: 8m/min, feed rate: 2m/min, quill diameter: 105mm, quill stroke: 225mm, taper: MK5, tool stations: 8. Machine dimensions X/Y/Z: approx. 5300mm/2300mm/2200mm, weight: approx. 7000kg. Documentation available. An on-site inspection is possible. Csdpexr Nvcofx Afleha

Condition: new, Year of construction: 2025, functionality: fully functional, The CNC BAYKAL Hybrid Press Brakes combines all the benefits of both hydraulic and all-electric press brake systems into one. If you’re looking for press brakes that are fast, accurate, and energy-efficient, BAYKAL is the way to go. Chedpfxsrq D Nij Aflja The CNC BAYKAL Hybrid Press Brakes can significantly save energy, save fuel, improve bending efficiency, reduce the risk of oil leakage, reduce installation costs, extend the service life of consumables, improve bending accuracy, reduce noise, and improve the working environment. The CNC BAYKAL hybrid press brakes system are designed with an individual electro-hydraulic servo drive system and servo pumps to control the for each of the left and right cylinders. The servo motor controls the output flow of the oil pump according to the program setting, and then controls the movement speed and position positioning of the slider, and there is no throttling phenomenon in the whole process. Therefore, all the energy output by the oil pump is supplied to the left-right oil cylinder. This control method does not have any energy loss, and the energy-saving effect is very prominent. With this system the hydraulics run on demand when the foot pedal is activated, rather than having a pump running continuously. This results in lower energy usage than a standard hydraulic machine as well as faster cycle times and extremely high accuracy. The flow and pressure of Y1 and Y2 oil cylinders are respectively controlled by two sets of servo bidirectional pump systems, and the oil in the upper chamber of the oil cylinder is directly pumped into the lower chamber of the oil cylinder through the oil pump to realize the lifting of the beam. The reverse rotation of the oil pump pumps the oil in the lower chamber of the oil cylinder directly into the lower chamber of the oil cylinder to realize the pressing and bending of the upper die. Applicable between from 100 Tons to 1250 Tons, the synchronization of the left and right of the upper beam of the CNC BAYKAL hybrid press brakes is controlled separately by two sets of servo bidirectional pumps.

Condition: used, Year of construction: 1997, The bending press was manufactured in 1997 in England by EDWARDS PEARSON. The folding press is in good condition, sold with tools. Always serviced and maintained on time. The machine tools are connected and can be tested and inspected. Chsdpfx Aforfx Utjlja Specification: Model: EDWARDS PEARSON 100/3100 PR6 Year: 1997 Working length: 3 100 mm Bending capacity: 100 T Travel: 172 mm Distance between table and frame: 450 mm Working speed: 100 mm/s Return speed: 110 mm/s Axes: auto X1, X2, Y1, Y2, Z1 , Z2 , R Tools: Available Weight: 7 T Other: New screen recently replaced, keyboard attached for ease of use. If you have more questions, we will be happy to answer.

Condition: used, Year of construction: 1992, sheet width 2050 mm plate thickness 10.0 mm ST pre-bending 8.0 mm ST diameter of upper rolls ~ 205 mm side roll diameter ~ 195 mm Control konv. Chedpfoxacdvjx Aflsa oil volume 80.0 Liter voltage 380 V total power requirement 5.5 kW weight 3200 kg range L-W-H 4500 x 1500 x 1300 mm Features: - Robust electro-hydraulic 3-roll bending machine - 3-roll concept offers a wide range of bending and rounding options - Pivoting control unit at the front * Operation - Control of all rolls and machine axes * Digital position display * Manual operation via joysticks - Diameters of up to 1.1 times the top roll diameter are possible - Forged and hardened rolls with a hardness of 53-55 HRC - Low-maintenance, stable machine design - Sturdy welded steel construction - Electro-hydraulic folding bearing for easy pipe removal - Pressure gauge / pressure indicator for the rolls - Safety device (safety lanyard with switch unit) - Operating instructions (PDF)

Condition: used, material width 300 mm coil weight 3 t material thickness 2 - 4 mm Straightener, 7 rolls, Make. Schleicher, Type RM 6-95/160 - band width 300 mm - band thickness 2 – 4 mm Codpfocdrmmjx Afloha - cross cut 1200 mm² - voltage 220/380 V 50 Hz - total power requirement 3,1 kW coiler with press roll, Make Schleicher, Type H-3 - Coil weight 3 t - Band width 400 mm - voltage 220/380 V 50 Hz - total power requirement 3,92 kW without control

Condition: used, Year of construction: 2011, turning diameter over bed 640 mm turning length 2.000 mm control 840D incl. Weiler SL1 Siemens centre height 320 mm swing diameter over face slide 405 mm radial face slide travel 380 mm travel upper slide 130 mm bed width 380 mm turning tool - shaft cross cut 32 x 25 mm turning speed range - main spindle 0 - 2.500 min/-1 transmission ratio 2 transmission ratio 1 0 - 800 min/-1 transmission ratio 2 0 - 2.500 min/-1 power capacity - main spindel 20,5 / 17 kW max. Torque 1.400 Nm spindle head Gr. 8 DIN 55027 spindle diameter in front bearing 120 mm spindle bore 83 mm taper bore 90 metrisch power feed longitudinal 10.000 N power feed coss 9.000 N feed range 0 - 20 mm/-1 rapid traverse 10/7 | 5/3,5 m/min Chedpfozhcfvjx Aflja metric 0,1 - 400 mm inch 1/4 - 56 G/1" module mm . II dia. of quill 100 mm quill stroke 200 mm capture MK 5 total power requirement 30 kVA weight of the machine ca. 5,7 t dimensions of the machine ca. 5,0 x 3,5 x 2,0 m Lathe cycle controled WEILER - E 60 / 2000

Condition: not inspected (used), Year of construction: 1996, turning diameter over cross slide: 1,000 mm, turning length: 4,000 mm, turning diameter: 1,450 mm, spindle bore: 150 mm, rotational speed (max.): 560 rpm, overall weight: 20,000 kg, CNC NUM T Plus Capacity 4000 x 1450 mm on bed 1000 mm on cross-slide 4-jaw chuck 1200 mm Steady rest Automatic turret Set of tool holders Weight 20,000 kg Chjdpfsyzhrkjx Afloa

Condition: used, Year of construction: 1957, turning diameter over bed 800 mm turning diameter over slide rest 540 mm turning length 4000 mm centre height 400 mm centre distance 4000 mm spindle turning speed range 9 - 1140 U/min spindle passage 96 mm weight of the machine ca. 8,5 t dimensions of machine L x W x H 7,0 x 1,70 x 1,70 m - with gap with insert - Accessories: 3-jaw chuck FORKARDT 400 mmø, 4-jaw chuck 500 mmø, faceplate 800 mmø, DRO on X-and Z-axis ACU-RITE, MULTIFIX-head with various inserts, 2 solid steadies, Chodpexwp Ehjfx Afloa 1 running steady, running center, coolant

Condition: as good as new (ex-display), MIG/MAG welding machine with inverter technology. Three-phase power supply, welding machine. Master Software TERRA PME included. Technical data Power Supply: Voltage (50/60 Hz): 3x400V ±15% Maximum input power: 22.9 kVA Maximum input current: 31.1 A Power factor PF: 0.73 Efficiency: 89% Slow-blow fuse: 25 A Open-circuit voltage: 61Vdc IP protection class: IP23S Insulation class: H Power cable: 4x3mm² – 5 m Codpjw Rm Sajfx Afleha Welding: Setting range: 3–400A Duty cycle MIG/MAG at 40°C: 40% – 400A, 100% – 330A Duty cycle MIG/MAG at 25°C: 100% – 400A Wire diameter: 1.0–1.2 mm (optional 0.6–1.6 mm) Flux-cored wire diameter: 0.9–2.4 mm Aluminum wire diameter: 0.8–1.6 mm Wire feed speed: 0.5–22.0 m/min Wire spool diameter: Ø 200/300 mm Remote control connection: yes

Year of construction: 2007, condition: ready for operation (used), A CNC profile drilling machine Voortman with a movable drilling cabin is available. Working height range: 30mm-1050mm, positioning speed: 40m/min, table width: 300mm, max. working width: 1800mm, support depth: 1500mm, tool stations: 5, max. travel speed: 40m/min, tool holder: SK40, drilling diameter range: 5mm-40mm, thread cutting range: M6-M30, working length: 16200mm. Documentation available. On-site inspection possible. Chjdpfxjxp Rb Is Aflja