Band saw

MEBA 335 GA

Condition: good (used), Year of construction: 2018, machine/vehicle number: 68892, Offer 26014 Hydraulic, Two-Column Guided Mitre Band Saw Automatic Machine Technical Data: - Automatic work cycle for cutting operation, hydraulic lifting / lowering of the saw frame, manual mitre adjustment with hydraulic clamping - Automatic material feed system, motorized mitre adjustment - Saw band dimensions: 4400 x 34 x 1.1 mm - Cutting speed, infinitely variable: 15 - 150 m/min - Cutting pressure regulation, infinitely variable: 10 - 15 bar - Lowering speed: 0 - 300 mm/min - Cutting range: - 30° to 90° - at 90° round: 335 mm - square-flat: 500 x 335 mm - at 45° round: 330 mm - square-upright: 320 x 335 mm - at 30° square-upright: 170 x 335 mm - Material feed automaton - Discharge roller conveyor: 4000 mm - Infeed roller conveyor: 4000 mm - Drive: 400 V / 6.5 kW - Required space (approx.): W 2300 x H 1750 x D 2200 mm Dkedpfx Agsytn Dio Dsk - Weight (approx.): 1800 kg

Condition: used, Year of construction: 2025, operating hours: 2 h, Operating hours: 2 New tractor with dealer daily registration prior to delivery Standard equipment / technical data Engine Rated power (ISO): 82 / 110 kW/hp at 2200 rpm Maximum power: 86 / 115 kW/hp at 2000 rpm Maximum torque: 460 Nm at 1600 rpm Manufacturer / Type: Agco Power / AP 44MBTN-D5 Low-emission engine, 4-cylinder / 4.4 l, 4 valves, STAGE 5 Regulated turbocharger, SCR catalytic converter DOC – Diesel oxidation catalyst SC soot particle filter One-piece, tiltable engine hood Exhaust on right side, in front of cab Fuel tank capacity: 198 liters / AdBlue: 18 liters Transmission / PTO 16/16-Speed Dyna-4, SpeedMatching, 40 km/h Dksdpfx Asyvmq Iog Dek PowerControl left-hand operation with powershift reverser, 4-step powershift Permanently cooled wet multi-plate clutches with independent lubrication system Dual-speed PTO: 540 / 540E / 1000 rpm Electronic shift in cab PTO START/STOP button on left rear fender Hydraulics / Rear linkage Open Center system, 58 l/min total flow, max. 200 bar 2 control valves with hydraulic couplers: 1x single/double-acting, pressure relief + 1x single/double-acting, neutral leak, SST Category 3 quick coupler with balls and catcher bowls CAT 3/2 Lower link draft control 5,200 daN maximum lift force, 2 external lift cylinders Adjustable lift rods on both sides and 2 side stabilizers EHR with external operation on both rear fenders Electrical equipment Thermostart, 120 A alternator Electric battery isolation switch 12 Volt power supply for external devices with socket Axles / Additional weights Rear axle ND with flange hub Oil-cooled disc brakes Height-adjustable automatic drawbar Rear fender outer width 2.00 m, without extensions Front weight carrier with integrated drawbar and towing pin Driver's station Standard cab with vibration damping, standard roof, ventilation and heating, air conditioning Integrated safety frame with tinted glass Doors on both sides with safety steps Adjustable steering column (height & tilt) Air-suspended driver's seat with armrests, swivel adapter, and seat belt 2 large telescopic exterior and wide-angle mirrors Interior mirror Analog-digital dashboard (SIS) Radio pre-wiring with antenna and speakers 4 work lights each at the front and rear of the cab roof 2 headlamps each in the engine hood and on the handrails, 2 work lights on rear fenders Rear window washer/wiper All-wheel front axle with selectable differential lock Special equipment With fuel tank protection PowerControl & brake to neutral (clutch effect) 100 l/min Open Center hydraulic system oil flow sharing (58+42 l/min) Leak oil collector at quick couplers 3 control valves: 1x pressure relief, double-acting, float, SST + 1x double-acting, neutral leak, SST + 1x double-acting, neutral leak, SST + free return 2.5 t front linkage, 1 hydraulic hose set, electrical socket 480/70R38 ADJ Ø1.69m & 380/70R28 ADJ Wide rear fender extensions Air conditioning Cab with mechanical suspension Telescopic exterior and wide-angle mirrors Passenger/instructor seat with belt Air-suspended driver's seat, automatic setting with seat belt, swivel adapter, and armrests Rear window washer/wiper Automatic battery isolation switch, 12

Condition: new, functionality: fully functional, Year of construction: 2025, operating hours: 0 h, machine/vehicle number: plate roll, control type: CNC control, degree of automation: automatic, actuation type: hydraulic, controller manufacturer: MG EVO, controller model: EVO 4 AXIS, number of rollers: 4, roller (bottom) diameter: 140 mm, roller (top) diameter: 160 mm, side roll diameter: 150 mm, roller diameter: 200 mm, roller length: 2,050 mm, working width: 2,000 mm, working height: 700 mm, sheet thickness (max.): 6 mm, sheet thickness steel (max.): 6 mm, sheet thickness stainless steel (max.): 6 mm, sheet thickness aluminum (max.): 6 mm, overall weight: 2,200 kg, total length: 3,200 mm, total width: 1,100 mm, total height: 1,200 mm, power: 4 kW (5.44 HP), input voltage: 400 V, number of digital displays: 4, warranty duration: 12 months, Equipment: cone bending device, documentation/manual, emergency stop, hardened rollers, 4 ROLL BRAND MG ITALY, HYDRAULIC MODEL M2006P EVO_CNC PLATE BENDING ROLL PLANETARY DESIGN DOUBLE PINCH PRE-BENDING CNC_EVO PROGRAMMABLE AUTOCALCULATION AUTOMATIC PLATE ROLLING Capacity: -Width of plate: 2000 mm -Thickness of plate rolling 6 mm -Thickness of plate pre-bending 4 mm Rolls -useful width mm. 2050 -Top roll mm. 160 - Lower roll mm. 140 Dksdpfjw Dnd Sox Ag Dsk Configuration installed: • Surface hardening of the four rolls, smooth finishing suitable for stainless plates rolling • Dual pre-pinch, with adjustable force upon the input of plate thickness • Conical bending hydraulic attachment - hardened contrast pad. • Power driven rolls rotation top/bottom gearbox axial direct drive hydraulic each roll. • Calibration system for re-rolling of welded shells rounding. • Console electric independent with centralized commands joysticks and CNC screen readout. • CNC controller on touch screen 15” , CAD/CAM interface 4 axis auto calculation software package. with digital readout of the axis for use in manual rolling, semiautomatic and fully automatic programmable. • Opening front side hydraulic drop-end to unload closed shells. • Variable working speed step-less axis interpolation. • Safety installation with emergency stop. • Instruction manuals for operation and service.

Condition: new, Year of construction: 2026, Completely refurbished machine, as new, modernized to the legally prescribed "state of the art" safety standard in accordance with the safety regulations of the employers' liability insurance associations. Switch cabinet electronics Installation of a new CE - control cabinet according to the current legal regulations of the professional associations BGVA 3 / DIN-EN 60204-1 new machine standard. Optionally complete machine in CE execution. A CE declaration of conformity is issued for the machine. With this FPS Werkzeugmaschinen GmbH acts as manufacturer. The machine fulfills the requirements of the BETRIEBS-SICHERHEITSVERORDNUNG- Betr.SichV. The year of manufacture corresponds to the date of delivery of the machine. EN ISO 12100, EN ISO 13857, DIN EN 13128:2009-09, EN ISO 13850, EN ISO 13849, EN 60204-1 Control system 3-axis - FPS Active - digital display Speed 25 - 2500 rpm geometrically stepped direct gear with 18 speed steps for maximum torque / milling power Feed rate 5 to 500 mm/min, infinitely variable rapid traverse 1,2 m/min quill Extendable quill, vertical 100 mm SK40 with M16 tightening thread optional: with DECKEL - saw thread S20 x 2 Extendable quill, horizontal approx. 100mm Axes X/Y/Z 800/300/400 mm Table rigid angular table 1000x440mm, load 2000kg Equipment - Vertical and horizontal spindle - Milling head manually tiltable +/- 90 °. Options - Z-axis bellows Dkodpfx Agjh Sptno Dek - chip tray - machine light - central lubrication - universal table - rotary table - Shaper head - dividing head - counterholder - etc.

Condition: new, Extraction capacity of filter unit at spigot*: 350 m³/h Total power consumption*: 0.09 kW Operating voltage: 230 V, 50/60 Hz, 1PH + N + PE Noise level*: 52 db(A) Dimensions L/W/H in mm: L 329 / W 374 /H 510 Colour: RAL 7035 Dkjdpfoh Rdwxsx Ag Dek Weight: 25 kg Manufacturer: ISI Industrieprodukte GmbH *Depending on the filter equipment Special voltage or special colour on request Application: Extraction of oil mist and smoke, for small to very large machine workrooms. Your advantages of the ELBARON series: - 18 unit variants available - Direct from the manufacturer - ISI-TRONIC as standard (digitalised filter control) - Electronically controlled EC fan as standard - Speed and air flow rate adjustable - Simplex (single-stage) or duplex (two-stage) available - Wide range of air flow rates available - Adaptable to pollutant load and air performance requirements - Large range of mounting and connection accessories - Quality Made in Germany We have developed the ELBARON® filter series for use in machining operations with pure oil or for separating oil mist and smoke. For many years now, the digital electrostatic air filters of the ELBARON® series have been among the most efficient filter units on the market and are in use worldwide. Our filter units are already digitalised as standard and can be controlled, for example, using a laptop. The ELBARON® unit series comprises 18 unit variants and can be optimally designed for your application in terms of size and performance. ELBARON® units impress with their long service life and absolute functional reliability. Our electrostatic filter cells are dimensioned in such a way that the best possible filter efficiencies, service lives and trouble-free operation are achieved under economic aspects.

Condition: used, mileage: 166,000 km, power: 96 kW (130.52 HP), first registration: 11/2012, fuel type: diesel, overall weight: 3,500 kg, color: white, gearing type: mechanical, emission class: euro5, number of seats: 3, loading space length: 3,850 mm, loading space width: 2,040 mm, loading space height: 400 mm, Equipment: ABS, central locking, * 1st hand * Aluminum platform * Mounting eyes * 6-speed * Driver's airbag * stereo * rail Dksdpfx Agsglgpns Dok * Payload 1500kg * WhatsApp/Tel.

Condition: used, Year of construction: 2004, pressure 80 t chamfer lenght 2550 mm distance between columns 2050 mm Stroke beam 350 mm max. opening beam/table 620 mm C-recess 420 mm traveldistance X1+X2 cnc programmable 700 mm Z1+Z2 axes controlled by cnc 0-2000 mm max. distance R-axes 200 mm Quick speed,inspeed 100 mm/sec bendingspeed 0-10 mm/sec opening speed 100 mm/sec Number of working hours 24000 h Dkedexyzzaepfx Ag Dsk length 3380 mm width 1800 mm height 2750 mm weight 6100 kg total power requirement 9 kW dimensions of the machine ca. 3x2x2,5 m All machines can be viewed under power at all times. Demonstrations of the machines possible at any time.

Condition: new, Year of construction: 2024, ♻ Universal use (diverse wood, pallets with nails and pins, particle boards, waste and scraps, veneer, MDF plates, cardboard boxes, plastics, textile etc.) ✔ Power: 22 kW ✔ Shaft length: 650 mm ✔ Shaft diameter: 270 mm ✔ Shaft RPM: 80-120 rpm ✔ Number of cutting knives: 2x14 ✔ Granulation: 10-50 mm ✔ Capacity: up to 5 m3/h* ✔ Material discharge opening: 160 mm Djdjhwwpzspfx Ag Dekk ✔ Filling opening: 1446 x 1342 mm ✔ Dimensions L/W/H: 1,92/1,55/1,79 m ✔ Weight: 1750 kg 2 years warranty or 2000 working hours

Condition: new, capacity 90 degrees: round 510 mm capacity 90 degrees: square 450 mm 650x450 band speed 15 - 100 m/min table height 844 mm dimensions of saw-band 5320 x 34 x 1,1 mm total power requirement 3,0 kW weight of the machine ca. 2,1 t dimensions of the machine ca. 1,9 x 2,87 x 1,3 m PROMOTIONAL PRICE!!! 2-column double miter band saw K-tech DG 62/45 HA-I • 2-column miter saw • Solid, yet easy to use • Material height sensor (automatic cut start detection) • Smooth running thanks to diagonal cutting, feed regulator + cutting pressure regulator • Solid material inlet roller • Removable chip tray (disinfection) • Energy-saving and low-vibration thanks to diagonal cutting • Control panel ergonomic, safe and free-standing • Frequency-controlled saw drive 15 -100 m/min. • Hydraulic cutting pressure control valve • Hydraulic control of saw frame and vice • LEDs for monitoring all safety functions • Large-sized wheels (520 mm) a. • Clear miter adjustment up to 60° Semi-automatic function: 1. Tension the material 2. Saw starts 3. Lowering in rapid traverse to the beginning of the material or the same for series cutting cut 4. Saw blade off Dkjdpfx Ajd Iipmog Dok 5. Raise the frame until it is just above the material 6. Vice opens

Condition: excellent (used), Year of construction: 2000, functionality: fully functional, travel distance X-axis: 800 mm, travel distance Y-axis: 600 mm, travel distance Z-axis: 500 mm, rapid traverse X-axis: 30 m/min, rapid traverse Y-axis: 30 m/min, rapid traverse Z-axis: 30 m/min, controller manufacturer: Heidenhain, controller model: TNC430, rotary table diameter: 540 mm, spindle speed (max.): 16,000 rpm, operating hours of spindle: 32,000 h, spindle nose: HSK63, number of slots in tool magazine: 30, Equipment: rotational speed infinitely variable, Very well-maintained HERMLE C800-U. Swiveling rotary table: 540 x 540mm Dedpfx Agsx Hg E Ts Dekk Program runtime only approx. 34,000 hours. Field of application: Toolmaking Service carried out by the manufacturer. Last spindle head replacement: 04/2017 New A-axis drive Heidenhain iR probe