Band Saw - Automatic - Horizontal

KASTO PBA 320/460 AU

Condition: used, Technical details: cutting diameter: 460 mm saw band length: 4670 mm saw band width: 45 mm cutting range 90 degrees: round: 460 mm cutting range 90 degrees: square: 320 x 500 mm band speed: 16...160 m/min feed stepless: ja / jes / Sí mm/min electrical connection: 380 V / Hz. total power requirement: ca. 7,5 kW machine weight approx.: 2900 kg dimension machine xH: 2,8 x 2,45 x 1,7 m dimensions L x W x H: Rollenbahn: 1,1 x 0,6 x 0,3 m FULLY AUTOMATIC BANDSAW Manual and automatic operation Multiple stroke = single up to 580mm and multiple up to 5220mm Tension via clamping jaws WxH: 100 x 250mm motorized band tensioning Saw blade cooling Ppjdpfx Asu Niixjnzjw piece counter Lubrication of the saw blade guide Accessories: Infeed track, motor-driven, LxW: 1300mm x 530mm Outfeed track LxW: approx. 1000mm x 750mm *

Year of construction: 2017, condition: ready for operation (used), - USED - FIBER LASER CUTTING MACHINE FOR TUBES WITH LOADING/UNLOADING SYSTEM MIN CIRCULAR SECTION: ø 25 mm MAX CIRCULAR SECTION: ø 355 mm MAX SQUARE SECTION: 260 X 260 mm MAX RECTANGULAR SECTION: 300 X 200 mm MAX ADMITTED LOAD: 100 Kg/m SOURCE: IPG YLS-4000 ; 4000 W Ppjdpfex E Eihjx Anzsw CONTROL UNIT: SIEMENS 840D WEIGHT: 12500 Kg NOTE: AUTOMATIC LOADING 3-12.5 mt; AUTOMATIC UNLOADING 12.5 mt; 3D CUTTING HEAD; CAPACITIVE SENSOR; AUTOMATIC ADJUSTMENT

Condition: excellent (used), Year of construction: 1995, Combination Unit: Manufacturer: GSG Pjdpfxer Nfvmo Anzjpw Feeder: Type: 840.02-027 Crusher Descaler: Type: 663.02-017 Wire Range: Ø5.5-16mm For wire rod with approx. 40-60 daN/mm² strength Crushing and Bending Rollers: Carbide Inserts Adjustment with 0.37 kW - 1.15 A gear motor Brush Drive with 0.25 kW gear motor, n=293 rpm Connection Voltage: 380-420 V 50 Hz Dry Coating Unit: Type: BSG/T Filling: Calcium Stearate (e.g., Traxit Type: D S 51 E) Stearate Consumption: approx. 350 g per t of wire Drawing Speed: max. 15 m/s Electrical Power: 2x 0.55 kW gear motors Cassette: 2 slots (supplied with 1x roller block + 1x cassette) Type: PKG/T (TS) Cleaned rolled wire Wire strength approx. 40–60 daN/mm² Wire range max. inlet diameter 9.5mm, finished diameter 3.5–8.5mm Roll dimensions min. Ø115mm, max. Ø125mm, Bore diameter Ø82mm, width 15–25mm Cooling pin diameter 25mm Cooling water consumption approx. 600 l/h Drawing machine: Manufacturer: Koch Type: KHZ 5000 Year of manufacture: 1993 Serial number: 13.821 Number of draws: 1 draw per block Drawing drum: Ø700mm Tensile force: mechanical 5000 N Wire material: mild steel wires Run-in strength: approx. 40 – 45 daN/mm² Maximum drawing range: Inlet diameter 5.0 – 8.5mm Cross-section reduction: 20 x 25% (mechanical gradation) Drawing speed: up to max. 7.0 m/s Brake: Twiflex, type: MRB Drive: AC motor/frequency converter, Siemens PN=110 kW, n=1485 rpm Spooler: Manufacturer: Koch Type: KHS 1250 Year of manufacture: 1993 Factory No.: 13741 Wire diameter: 5 – 8.5 mm Strength: approx. 55 – 70 daN/mm² Winding speed: V=7 m/s, adapted to the drawing machine Filling weight: approx. 3000 kg Spool drive motor: Three-phase motor with external fan Type: 1 PQ 6253 – 6 AA 70- Z A 15 + K 20 + C 14 + H 46 P=37 kW, n=1000-2000 rpm, IP54, design B3 Laying drive motor: 66-671U, 1.5 kW, 170 V, 9.8 A, 1680 rpm, IP 44, B5-200 With Attached tachometer generator TG 20, 20 V / 1000 rpm With attached spur gear SK 32, i=57.53, design B6 Hydraulics: Hydraulic excavator type: H13 AK Pneumatics: Twiflex disc brake type: MRB Pneumatic cylinder type: SPWG 28032-25mm stroke Dimensions: 3100 x 3000 x 1700 mm (L x W x H) without counterweight

Condition: new, Year of construction: 2025, - Horizontal capacity: 500 kg - Vertical capacity: 250 kg - Table size: 560 mm - Door on the left: 170 mm Ppodpfxsgg Rb Tj Anzew - Electrically tiltable - Foot pedal - Documentation - 230 V

Condition: good (used), Year of construction: 2001, Cutting 90°: 330 Cutting flat 90°: 330 x 330mm Cutting speed Vario:12 - 120 Circle blade size: 6830 x 41 x 1,3mm Power: 7.5kW Length: 4600mm Width: 2150mm Height: 2310mm Weight: 4300kg Ppodju R R Acjpfx Anzew Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!

Condition: used, Year of construction: 2011, Technical details: turning length: 310 mm swing diameter over bed: 500 mm swing diameter over bed slide: 290 mm centre distance: 500 mm x-axis: 190 mm z-axis: z1: 335 / z3: 370 mm y-axis: 80 mm revolution per minute: 6000 U/min Control: Heidenhain CNC Pilot 4290 spindle bore: 73 mm bar material dia.: 50 mm tool turret - number of stations: 12 tool taper: VDI 30 mm rapid traverse x + z axis: 30 m/min operating hours - idle run: 36443 h Pjdpfxjw S Efze Anzspw spindle hours: 8545 h interface: ja total power requirement: 20 kVA kW dimension swarf conveyor LxWxH: 3,2 x 0,45 x 1,5 CNC inclined bed lathe With a 3-jaw chuck Ø 160mm with matching flange (max. speed 4500 rpm) and 2 additional sets of spare jaws. Turret head for 12 tools all with tool drive; Sauter disk turret (C-axis = 300 rpm) Torque main spindle: 95 Nm at 100% and 127 Nm at 40% Chip conveyor 450 K-1/250; year of manufacture 2000 Electric cabinet with Rittal cooling The machine does not have a hydraulic chuck. A manual chuck has been installed by the previous owner. The machine is not functional and is for sale. The machine has an unknown malfunction in the turret, meaning that reference travel and axis movements are not possible. Machining functionality is therefore currently not possible. The machine is for sale and in need of repair! i.D. *

Condition: used, Radial drilling machine CSEPEL, Type RFh 75 / 1500 Machine no. 13704, Year of manufacture 1985 Drilling capacity in steel: Ø 75 mm Drilling capacity in cast iron: Ø 90 mm Spindle mount: MK 5 Nominal overhang: 1500 mm Maximum overhang of the spindle: 1500 mm (to the column) Minimum overhang of the spindle: 440 mm (to the column) Distance from spindle nose to clamping surface: 370 - 1700 mm Overarm vertical adjustment: 950 mm Table size / clamping surface: 1800 x 1100 mm Column diameter: 450 mm Quill stroke: 380 mm Spindle speed: 19-1900 rpm, 21 steps Feed rate: 0.047-2 mm/rev, 12 steps Motor power: 11 kW Mains connection: 380 Volts, 50 Hz, 15 kW - Right-hand and left-hand rotation of the drilling spindle via hand lever switch - Hydraulic gear change for spindle speed and feed rate - Hydro-mechanical central clamping device - Motorized overarm vertical adjustment Pedpslhwr Rofx Anzspw - Without coolant system - Machine light - Operating manual Space required: Length 2720 mm x Width 1170 mm x Height max. 3770 mm Transport height with motor on the column: 3500 mm Transport height without motor on the column: 3250 mm Weight: 6.3 tons Good condition

Condition: new, Year of construction: 2026, 2-roll driven profile bending machine Hydraulically adjustable top roller Shaft diameter: 40 mm Roller diameter: 152-162 mm Revolutions: 8.5 per min. Top roll adjustment: 120 mm Capacity table: in the attachment Podpfx Ashgiuhenzepw Machine available in various versions: Manual adjustment, 3-roll driven etc.

Condition: used, Year of construction: 1994, cutting diameter 520 mm saw band length 7239 mm cutting width 1,3 mm Control POSIMOD cutting range - square - 520 x 520 mm feed length 500 mm feed length: multiple 4500 mm min. cut-off length 6 mm length of rest piece min/max 10 / 100 mm cutting speed 20 - 130 m/min dimensions of saw-band 7239 x 50 x 1,3 mm sawing motor 5,5 kW total power requirement 10,0 kW weight of the machine ca. 3,8 t dimensions of machine L x W x H 3,42 x 2,30 x 2,40 m - 2 column guided - Accessories: roller track 2500 mm length, chip conveyor, coolant Pjdpewm Rm Iefx Anzepw

Condition: good (used), travel distance X-axis: 745 mm, travel distance Y-axis: 370 mm, travel distance Z-axis: 300 mm, Bridgeport milling machine Type: Interact 4 Control: Heidenhain TNC 155 X-path: 745 mm Ppjdeqgcdtspfx Anzow Y-path: 370 mm Z-path: 300 mm Bed: 960 x 380 mm Spindle: ISO 40 Dimensions: 185x180x235 cm LxWxH