Vacuum drying kiln

ISVE ES 2

Condition: used, Year of construction: 1992, Technical details: max. temperature: 120 °C internal diameter: 980 mm internal length : 2580 mm external diameter: 1500 mm external diameter : 2740 mm wall strength: ca. 6,5 mm content: ca. 2000 l weight: 1425 kg Autoclave tank It is possible that this autoclave were built for the process of steam sterilization (according to operating parameters) The operating overpressure of +2 bar per room probably refers to the execution of the steam sterilization process, not to the pressure resistance of the container. - Permissible operating temperature 120 °C Lajdpfeu Nz I Tjx Apmed *

Condition: used, No. 3213 Thermal treatment system / vacuum dryer WTT Used, year of construction 2017 Thermal treatment system / thermal chamber for the modification of wood The WTT thermal chamber is a system for the thermal modification of wood. It enables efficient treatment of 2 to 3 batches per day, depending on the thickness and type of wood. The system has a powerful energy and heat transfer system and works with a gas or oil-fired boiler system that uses thermal oil as a heat transfer medium. Technical data: Capacity: 5950 - 9900 m³ of wood per year (for 330 working days) Usable volume: 9 m³ (with 50 mm wood thickness) Stack dimensions: 10500 x 1300 x 1100 mm LWH Minimum board thickness: 10 mm Power connection: 3 x 400 V, 50 Hz + zero + earth, 63 A Specific power consumption: 15.9 kW/m³ Lasdpfx Aov Si Szepmod Maximum heat output: 2 MW (230 °C - 250 °C thermal oil) Heat consumption: 120 kWh/m³ wood Autoclave length: 11,000 mm Autoclave diameter: 1,800 mm Autoclave material: 10 mm stainless steel duplex EN 4462 Door opens hydraulically, with 1.5 kW drive Working pressure: 0.1 to 15 bar (absolute) Working temperature: 0 °C to 220 °C 200 mm glass wool insulation, clad with 1 mm galvanized sheet steel Main components: 1. autoclave, in which the heat treatment takes place 2. vacuum system that sucks the air out of the autoclave before heat is applied 3. energy center with a 2 MW oil burner 4. 4 MW cooling system with dry coolers 5. nitrogen generator 6. gas cooler system Heating and cooling system: Heat exchanger: 8 units (4 on each side) Material: Stainless steel pipes (seawater resistant) Total floor area: 165 m² Cooling water consumption: 1000 l/batch (not contaminated, only heated) Control and operation: Control system: WTT ExoT (fully automatic) 22” color monitor, IBM computer, printer Sensors: 4 PT100 temperature sensors 2 mechanical thermometers 1 vacuum/pressure transmitter 1 mechanical vacuum/pressure gauge Special equipment: Hydraulic rail bridge for convenient transportation of wooden trolleys Automatic trolley extraction with cable winch (1.5 kW) 2 MW thermal oil boiler (heating) Fuel oil tank (4000 l) with measuring system Insulated 20 foot steel container for heating module Stainless steel safety chimney (300 mm diameter, 6000 mm length) Functional description: 1. filling the autoclave with wood 2. creating a pre-vacuum 3. filling with gas 4. heating 5. modifying 6. cooling 7. pressure equalization 8. creating a post-vacuum / drying 9. pressure equalization 10. emptying Certified EC Pressure Equipment Directive (PED) 97/23/EF Construction EN 13445 Sale on behalf of customer, from location near 5020 Salzburg (Austria), without dismantling, transportation and assembly Dismantling, loading and transportation by us optionally possible Subject to errors in the description and price To avoid possible misunderstandings, an on-site inspection by appointment is possible and recommended Sold as is Technical details, condition description, year of construction and scope of delivery according to manufacturer's brochure or previous owner, without guarantee Subject to prior sale For used machines, any warranty is excluded, the following applies: “purchased as seen” Pictures and videos serve as examples and do not represent the actual scope of delivery Terms of payment: Prices excl. VAT, payment before collection or dispatch Terms of delivery: ex location

Condition: good (used), Year of construction: 2017, conveyor belt length: 7,100 mm, conveyor belt width: 2,500 mm, Double steering Wheel diameter Platform size 7100 x 2500 mm Inspection valid 11.2025 Ledpfx Aewq N Sdjpmsad Length:7100mm Width:2500mm Height:900mm

Condition: used, Tenoning spindle 1 St. Number of milling agregates 4 St. Spindle diameter 50 mm Weinig Unicontrol 6 window system ----- Manufacturer's description: For the production of individual parts, elements, and small series. Spindle arrangement: One cross-cutting saw, one single-sided tenoning and slotting spindle, one right-hand profiling spindle, one tenoning and slotting spindle, and profiling spindle suitable for holding multiple tools stacked on top of each other, with pneumatic spindle movement. Slotting table with motorized table movement and automatic transfer to the continuous, chainless rubber roller feed of the profiling unit. Feed height adjustment manually. Lodpfx Aox Tu N Hspmsad Workpiece clamping via 2 pneumatic clamping cylinders. Length stop with scale and magnifying glass for frame or sash external dimensions. Tool positions (longitudinal and transverse machining) controlled via selector switch on the control panel. Technical Specifications ----- Crosscut Saw ----- Number of Tools: 1 Spindle Speed: 2,800 rpm Spindle Diameter: 40 mm Max. Tool Diameter: 350 mm Motor: 3 kW Mortise and Slot Spindle ----- Number of Tools: 3/4 pcs. for wood thicknesses IV 68 - IV 92 Spindle Speed: 3,500 rpm Spindle Diameter: 50 mm Tool Clamping Length: 320 mm Max. Tool Diameter: 320 mm Motor: 11 kW Profile Spindle ----- Number of Tools: 3/4 pcs. for wood thicknesses IV 68 - IV 92 Spindle Speed: 6,000 rpm Spindle Diameter: 50 mm Tool clamping length 320 mm Max. tool diameter 232 mm Motor 11 kW Special equipment: Synchronous spindle ----- Pneumatically timed forward/backward for tear-free rerouting of window sashes, frames, and doors. Spindle diameter 50 mm, 4 kW Tool clamping length 120 mm, zero tool diameter 112-140 mm Max. tool diameter 232 mm, spindle speed 6000 rpm Motor boost for synchronous spindle from 4 kW to 7.5 kW Screen control for 99 window types. One type can contain up to 8 different parts, each with 2 end profiles and 2 longitudinal profiles. Production options: single parts, double parts, frame-by-frame, series, rerouting. Data entry via keyboard with integrated operator guidance and error diagnostics. 1 Grooving spindle from above ----- Motor power: 2.2 kW Speed: 6000 rpm Spindle diameter: 40 mm, with 10 x 4 mm key Clamping length: 13 mm Clamping length: 40 mm Axial stroke, 2 positions Radial stroke, 2 positions Max. tool diameter: 130 mm Grooving spindle motor boost from 2.2 to 3 kW 1 Fitting milling unit, right: ----- For milling fitting grooves in the circumferential milling pass or for grooving in the longitudinal profile. Pneumatic horizontal movement with selector switch on the control panel. Motor power: 2.2 kW Speed: 6000 rpm Spindle diameter: 40 mm Clamping height: 125 mm Tool cutting radius: min. 140 mm, max. 180 mm Home position below table level: 10 mm Special design of the fittings milling machine: Clamping length 150 mm Axial stroke 80 mm, 3 positions 3 tools Radial cycle, 2 positions Motor booster for the hinge milling spindle from 2.2 to 3 kW Hinge milling spindle for 230 mm tool diameters in and above the table Electric height adjustment of the feed with selector switch on the control p...

Condition: new, Type SK-1000-P6 Working width 1000 mm Min.working length 500 mm Working thickness 2-150mm Polishing roller speed - Frequency control Lajdpfx Aodmi Niopmod Feeding speed 3-12,5 m/min Total motor power 13.87 kW Disc motor 1.5 kW*1 Cross motor 1.5 kW *1 Screw roller motor 2.2 kW *2 Feeding power 2.2 kW Up and down motor 0.37kW*4 Swing motor 0.37kW *2 Working table up and down 0.55 kW Transport dimensions 3650x1850x2100mm Weight 4200 kg

Condition: good (used), Table milling machine, table milling machine -Table milling machine: with rigid spindle -Speeds: rpm -Motor power: kW -Dimensions: 1000/1870/H1040 mm Ljdpfxecl Svvj Apmead -Weight: 560 kg

Condition: ready for operation (used), functionality: fully functional, Handtmann VF616 Vacuum Filler The Handtmann VF616 vacuum filler is a benchmark machine in the food processing industry for the precise portioning of meats and pasty products. With advanced technology, it ensures consistent filling even at very high throughput, while maintaining a homogeneous, bubble-free texture. It is perfectly suited for industrial production lines that demand productivity, quality, and hygiene. This filler features a robust vane cell feed system, ensuring reduced wear and continuous performance. In addition, its intuitive digital control allows for highly accurate portion adjustment and centralized management of various parameters, which enhances product consistency. Integrated vacuum technology improves product shelf life by reducing oxidation. Ljdpfx Aoxrn Tyspmoad The Handtmann VF616 is compatible with a wide range of accessories such as automatic clippers, formers, and depositors to suit different production types: sausages, pâtés, protein purees, etc. Its compact design allows for easy integration into existing lines, while its hygienic construction facilitates cleaning and reduces downtime. In summary, the VF616 delivers exceptional versatility, high mechanical reliability, and optimal return on investment for manufacturers seeking uniformity, speed, and compliance with strict hygiene standards. Technical specifications: Height: 2,120 mm Width: 1,580 mm Length: 2,250 mm Weight: 1,100 kg Power supply: 380V-400V Capacity: 2,000–3,000 kg Total power: 4.5 kW

Condition: excellent (used), functionality: fully functional, Vemag sausage production line (Stuffer, portion cutter, hanger) Vacuum stuffer with loading Vemag brand Model HP 7E Year of production 2008 Power 10kW Voltage 400-460V 15A 50/60Hz Lodpfx Apov Ucgkemead Portion cutter Vemag brand Model LPG 208 Year of production 2011 Power 6kW Voltage 400-460V 9A 50/60Hz Hanger Vemag brand Model AH 204 Year of production 2011 Power 1.5kW Voltage 400-460V 3.5A 50/60Hz

Condition: as good as new (ex-display), Year of construction: 2026, Compact wide-belt sanding machine with combination sanding unit Promotional features: - Switching the sanding pad on and off from the control panel - Switching the roller on and off from the control panel - Electronic control system Fox 500 KTR - Table extension with 2 rollers, with infeed and outfeed - Automatic table positioning with push button Article number: 5222100A2 Also suitable for smaller workshops for occasional use Combination sanding unit with sanding pad for fine sanding Standard equipment includes a diagonally grooved steel roller, Ø 120 mm, for calibrating Fine adjustment of the working height Clear control panel on the front Robust, tubular-reinforced monoblock steel machine body, robot-welded, with work units mounted high up for maximum rigidity Ledpfsgf Sw Nsx Apmjad Motorized height adjustment of the work table with digital display Electronically controlled sanding belt oscillation Carpet feed via geared motor with two speeds Natural rubber feed carpet with a negative profile Flexible steel pressure bar in front of the first unit Rubber pressure rollers, in front of or behind each work unit Pneumatic belt tensioning per unit with decimal correction option for grit size/belt thickness Universally applicable for solid wood and veneer thanks to the combination unit Entry-level model for smaller companies Working width 950 mm Equipment details: Combination unit for calibrating and sanding Diagonally grooved steel roller, Ø 120 mm, with fine height adjustment Hard sanding pad with graphite pad Universal design for calibrating and sanding solid wood, chipboard and veneer Technical data Length (product) approx. 1388 mm Height (product) approx. 1668 mm Width/Depth (product) approx. 1545 mm Connection for dust extraction Dust extraction nozzle diameter 140 mm Electrical data Connection voltage 400V Current type AC Phase(s) 3Ph Mains frequency 50Hz Power feed motor 0.33 / 0.55 kW Power height adjustment motor 0.25 kW Power drive motor 7.5 kW Sanding unit Sanding belt length 1525 mm Sanding width max. 950 mm Sanding belt width 970 mm Feed unit Feed speed 4.5 / 9 m/min Workpiece Workpiece height min. 4 mm Workpiece height max. 170 mm

Condition: excellent (used), Four-side planer Weinig Hydromat 23C Working width: 230 mm Working height: 160 mm Number of spindles: 7 Spindle arrangement: 1. Bottom 15 kW Lasdpoxlcufofx Apmed 2. Right 7.5 kW 3. Left 7.5 kW 4. Top 15 kW 5. Bottom 30 kW (multi-blade saw) 6. Bottom 7.5 kW (hydro support) 7. Top 7.5 kW (hydro support) Spindle speed: 6000 rpm Spindle diameter: 50 mm 4 feed rollers in the worktable Feed speed adjustable via frequency inverter up to 36 m/min Feed drive powered by cardan shaft Pneumatic pressure elements Technical documentation