Bar feeder

IEMCA TAL/AUTO 65/32

Condition: as good as new (ex-display), Year of construction: 2021, machine/vehicle number: 06 61 218, Comm. no.: Lg 32821 Lasdpfeg U Utvex Ampoa Single side decoiler BBT ABH 2000/400 exhibition machine, unused machine no.: 06 62 218 year of manufacture: 2021 Technical data load capacity approx. max. 2.000 kg strip width max. 400 mm Coil inner diameter approx. 450 to 520 mm Coil outer diameter max. 1,500 mm Unwinding speed approx. 2 to 15 min.-1 With adjustable drive and loop control via ultrasonic sensor (analog). Drive by frequency-controlled three-phase geared motor. Spreading of the support segments manually by means of hand crank via joints Number of supporting segments 3 Coil side guide via strong limiting arms, clampable. Reel stand in strong box construction as welded design. construction. Additional equipment: Shutdown "belt loop too small" by antenna switch, attached to the column of the bottom housing of the loop control. Infinitely adjustable in height. Tape side guide at the bottom housing of the loop control, by means of lateral guide rods. The passage width is continuously adjustable.

Condition: used, Thread rolling machine ORT RP30U 2-roll 30 ton swiveling heads variable speed drive Lsdpfx Aet H Ty Uompeaa #1331 Under power in our warehouse in Gussago BS. Test run possible M i m u Machine Tools Italy Rolling is a mechanical process without chip removal that can be performed cold or hot, having as a purpose the improvement of the surface finish (therefore the fatigue behavior Power (Ton): 30 Number of rollers: 2

Condition: used, total length: 1,330 mm, total width: 1,040 mm, total height: 1,150 mm, Empty weight: 1.800 kg Price: On request - Documentation available: No - CE certificate present: No - Drive system: Conventional - Shaft diameter [mm]: 85 - Capacity diameter round [mm]: 60 - Transport dimensions: 1330mm x 1040mm x 1150mm (l x w x h) - Transport weight [kg]: 1800kg - Transport packages [pcs.]: 1 Lajdpoxuf Slefx Ampja Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Lukas van Rossum

Condition: used, 3-roller bender Brand RAGACHE Type New Tube CP70 3 drive rollers diameter 232 mm Rectangle capacity Standard steel 60.0 mm Round capacity Standard steel 40.0 mm Laedpfsuluhwjx Ampea Capacity L Standard steel 70.0 mm Capacity U Standard steel 120.0 mm Capacity T Standard steel 60.0 mm Capacity I Standard steel 120.0 mm

Condition: used, mileage: 209,000 km, power: 96 kW (130.52 HP), first registration: 10/2013, fuel type: diesel, overall weight: 3,500 kg, color: white, gearing type: mechanical, emission class: euro5, number of seats: 3, loading space length: 4,200 mm, loading space width: 2,050 mm, loading space height: 2,050 mm, Equipment: ABS, central locking, * Aluminum platform * fastening eyes * ster * gel * ABS Lodpfohqzg Hox Ampoaa * ASR * Central locking * 6-speed * Power steering * Driver's airbag * Steering wheel adjustment * CD radio * Payload 1400kg * Ladder grille * WhatsApp/Tel.

Condition: used, Thread Rolling Machine, Cold Rolling Machine, Thread Rolling Machine, Profile Rolling Machine Manufacturer: PEE-WEE Model: UPW 24 Serial No.: P07 Year of manufacture: 2007 Maximum rolling force: 24 tons Maximum tool diameter: 270 mm Roll spindle diameter: 69.85 mm Laedpfouz If Nsx Ampsa Tool bore diameter: 70 mm (nominal diameter) Maximum tool/reception length: 180 mm Maximum workpiece diameter: 50 mm Hydraulic motor power: 3 kW Roll drive motor power: approx. 5.5 kW Electrical connection: 400 Volt, 50 Hz, 10 kW - Pivotable roll spindle for through-feed thread rolling - Roll spindle speed adjustable in 4 steps via gearbox shift - Hydraulic unit integrated in the machine base - Operating manual with electrical schematic Space requirements (L x W x H): 2,000 x 1,450 x 1,900 mm Weight: approx. 3 tons Very good condition Plunge Rolling: The thread rolling tools, having the same pitch as the workpiece, form the thread by penetrating the workpiece up to the nominal diameter. The maximum thread length is limited to the width of the rolling dies. Through-feed Rolling: Used when the thread length is greater than the width of the rolling dies. Through-feed tools are divided into three sections – entry, calibration, and exit. Knurling rolls have no pitch and are swiveled at the lead angle corresponding to that of the profile to be rolled. Lead angle rolls differ from knurling rolls by having a pitch in the profile. The sum of the lead angle and swivel angle results in the effective lead angle in the workpiece.

Condition: used, Roller sets for section bending machine, 3-roll ring bending machine HERKULES WETZLAR The rollers fit a section bending machine HERKULES WETZLAR type BO 238 N Shaft diameter: 60 mm with 18 mm keyway Lodpfjglaq Ijx Ampsaa 2 rollers set No. 1, roller diameter = 110 mm, roller width = 180 mm 2 rollers set No. 2, roller diameter = 160 mm, roller width = 40 mm 3 rollers set No. 3, roller diameter = 150 mm, for tube diameter Ø 33 mm, roller width 87 / 115 mm - Roller set No. 3 with adapter ring from Ø 93 to Ø 60 mm without keyway The machine had 2 driven rollers Total weight of all rollers: 57 kg Good condition

Condition: new, Year of construction: 2024, load capacity: 300 kg, Welding turntable KT 300 Horizontal load 300 KG, tilted 150 KG Power consumption 220V, 50 Hz Table diameter 450mm Height 500mm Lsdpfoc Ug Tljx Ampsaa Infinitely variable tilt range via crank gear motor 0 - 90° Speed 0.3 to 2.5 rpm Incl. foot remote control Surcharge: Quick-release jaw chuck Diameter 300mm, 450.-€

Year of construction: 1990, condition: good (used), machine/vehicle number: 3-201065, Material passage in the supply pipe max .: 65 mm for material lengths up to: 3000 mm Feed force infinitely adjustable up to max .: 550 N. Ledpfx Amsdlm Dhjpsaa Charging time approx .: 30 s elec. Connection / power requirement: 380 V / 1.5 kW Space requirement: 5810 x 920 x 1515 mm Weight: 1200 kg

Condition: used, color: yellow, first registration: 01/1995, * Manufacturer: HYSTER,* Type: H2.50XM,* Serial No.: D177B22181S,* Attachment: S/S 2.00-1.50 1067 mm,* Year of manufacture: 1995,* Drive: Diesel,* Operating hours: 18151.8 h,* Unladen weight: 4265 kg,* Reverse tilt: 6 degrees,* Tire size: 7.0 x 12 (front). 6.0 x 9 (rear),* Tire pressure: 0 (front / rear),* Track width: 1125 mm,* Lifting capacity with vertical mast and additional equipment as specified above,* Lifting height: 5550 mm,* Load capacity: 2040 kg at 500 mm, 1860 kg at 600 mm, 1710 kg at 700 mm, subject to alterations, prior sale and errors excepted. Ledpji Tfapjfx Ampeaa