Universal lathe

FAT TUR 630A x 3000

Year of construction: 1960, condition: good (used), machine/vehicle number: 970015, Load capacity with horizontal faceplate position: 10 t Load capacity with vertical faceplate position and centre of gravity distance 300 mm: 10 t Load capacity with vertical faceplate position and centre of gravity distance 830 mm: 5.5 t Face plate dimensions: 1500 x 1500 mm face plate speed hydraulically infinitely variable: 0,025 - 0,75 rpm Pivoting range: 0 - 135 Swivel time for full swivel range to: 140 s Swivel time for full swivel range down: 120 s Hydraulic drive: 380 V Height of swivel axis above floor: 1450 mm space requirement: 3800 x 1950 x 1800 mm Weight approx.: 3,5 t Giodpfxecblc Sj Afnon Weight of the counterweight: 2,3 t

Condition: good (used), Technical specifications: Working width: 4050 mm Max. bending capacity: 6.0 mm Max. pre-bending: 4.0 mm Top roller diameter: 210 mm Gjdjwkaalopfx Afnoin Side lower roller diameter: 210 mm Middle lower roller diameter: 210 mm Conical bending device by tilting the two side rollers Hydraulic folding bearings Pivoting control panel with digital display Dimensions (length x width x height): approx. 6900 x 2300 x 1800 mm Weight: approx. 14 tons The seller is not liable for typographical or data transmission errors. The machine's appearance, technology, and wear are consistent with its age; used machines are sold without any warranty.

Condition: used, Electric roll Bending Machine 3 rolls Maxi Length: 1000 mm Maxs Thickness: 3 mm Rolls diameter: Ø 80 mm Gedpow Ti Uvofx Afnoin Dimensions (L x W x H): 2000 x 1000 x 1000 mm Weight: approx 1 T

Condition: good (used), Year of construction: 1996, tube diameter 6 - 28 mm wall strength 2 mm bending radius min. 2 x D Control IPU 20 bending radius max. 5,0 x D mm bending angle max. 190 ° arbor length 3000 mm Godpfx Afevtgn Njnoin operating pressure 180 bar hydraulic motor 4 kW weight of the machine ca. 900 kg dimensions of the machine ca. 3,8 x 1,1 x 1,3 m Semi-automatic electro-hydr. mandrel tube bending machine with PLC control for 20 angles and display in the control panel for bending angle specification, angle detection and angle measurement via absolute value encoder, autom. tool plate reset, Turning device with digital display, hydr. quick chuck, aut. Mandrel lubrication, adjustable length stops. Operating modes: MANUAL and semi-automatic. Control buttons: hydraulics on / off, operating mode selection, clamp to / on, clamp forward / backward, mandrel forward / backward, bending forward / backward /, locking forward / backward, mandrel lubrication, turning device forward / backward, plate reset, length stop forward, emergency stop. The machine comes from a prototype construction and was only used a little until 2000. After that, the machines of this department were sold. However, the purchaser did not use the pipe bending machine and therefore it has only stood in the warehouse and has not worked since then ((original paint). Please notice that the price of a new machine today is over € 60.000,--. Machine dealer with own stock of 1600 m².

Condition: new, table diameter 330 mm table load 220 Kg swivelling range 135 Grad tilt adjustment: manually/mechanicall manuell Gsdpfx Ash D Svcefnein turning speeds max. 5 U/min stufenlos table load capacity 100 kg. vertikal total power requirement 0,125 kW weight of the machine ca. 48 Kg dimensions of the machine ca. 640 x 440 x 630 m

Condition: used, Year of construction: 1999, tube diameter bis 60 mm Gedpfx Asvvnm Sefnjin weight of the machine ca. 1,8 t

Year of construction: 1990, condition: used, machine/vehicle number: xxxx; Lg-Nr. 17250, Technical data: -Load capacity 200 kg Gisdpfxedd Ilxe Afnjn -Throat depth 800 mm -Working height in horizontal position approx. 1000 mm -Mot boom. left + right swivel - arm arm manually Tiltable -Mot face plates. left + right rotatable - faceplate speed infinitely variable - faceplate diameter 300 mm - adjustable control panel with control make ESAB, - type 6 PTF, BJ. 97 - space requirement approx. B 1100 x H 1300 x T 1600 mm -Weight approx. 300 kg

Year of construction: 1989, condition: ready for operation (used), A Darley CNC press brake is available. Pressing force: 2000kN, working width: 5200mm, power: 15kW, oil capacity: 160l, machine dimensions X/Y/Z: approx. 5500mm/1900mm/3100mm, weight: approx. 20000kg. Including tools and accessories. Documentation available. On-site inspection is possible. Gisdpfovf Ixysx Afnon

Condition: used, Bending capacity: Ø45 mm Bending angle: 0 - 180° Revolver-adjustment: 8-fold adjustable angles Mandrellength: 4000 mm Sets of bendingdies: 1x Ø 16 mm 2x Ø 17 mm 3x Ø 20 mm 2x Ø 27 mm 1x Ø 28 mm Giedpfx Afoq Nipyonen 2x Ø 30 mm Featured with: - 4 Mandrels - Mandrel retraction unit Country of origin: Germany Motor power: 3 kW Machine LxWxH: 400 x 100 x 120 cm Machine weight: 1500 kg

Year of construction: 1993, condition: ready for operation (used), Center height: 280mm, distance between centers: 2000mm, turning diameter over bed/cross slide: 570mm/365mm, spindle bore: 62mm, speed: 2500rpm, max. workpiece weight: 1000kg, bed width: 360mm. Machine dimensions X/Y/Z: approx. 4000mm/2250mm/2000mm, weight: approx. 5500kg, control: Siemens. An on-site inspection is possible. Giodpfx Ajxq Eyuefnsn