KBK Curves

Demag

Condition: excellent (used), Year of construction: 1998, cutting diameter 150 mm cutting range min. 150 mm saw blade diameter 400 mm cutting length min. 420 mm cutting lenght max. 4000 mm dimensions of the machine ca. 4800 x 1100 x 1500 mm Nedpjvwgnwsfx Aa Ejlk The double tiller saw is in very good condition and has only been used very little use.

Condition: new, 900 mm 900 mm 900x900 mm saw band length 9300 x 67 x 1,1 mm table height 790 mm band speed 14 - 60 m/min total power requirement 11 kW weight of the machine ca. 8,45 t dimensions 4,485 x 1,68 x 3,15 m The semi-automatic, hydraulic saws from the X-tech line offer the best Saw technology and best performance when cutting special steels • The electro-welded machine frame and the steel saw frame meet requirements all cutting needs and eliminate vibration and noise. • The chip conveyor is hydraulically driven and the speed is adjustable Nlodjfg E Hpjpfx Aa Ejk • All movements of the machine (saw frame, vice, feed, Saw band guides) are carried out thanks to modern linear guides with high static and dynamic load performance, which also has very low sliding friction to guarantee. • Another characteristic feature is the roles for the Positioning of the material by a hydraulic motor are driven. They move at right angles to the material, and thus allowing optimal clamping of the material. • Thanks to the height control of the saw band position, the operator can place the band in place near the top edge of the material. After the cut is finished, the tape automatically raised back to the previous position. Alternatively you can also “Remain” can be selected in the lower position. During the The software compares the cutting load with the cutting cycle Default. This means that the sawing system can be stopped in the event of irregularities become. • The saw band is cleaned by two adjustable steel brushes. The drive takes place hydraulically. • The hydraulic unit including filter and pressure gauge guarantees one particularly quiet operation at constant pressure. • Finely ground carbide inserts that clamp the saw blade, complete with lateral, hardened and adjustable guide rollers. The adjustable one The tape guide automatically moves as close as possible to the material. • The saw band is tensioned via a hydraulic cylinder, which is carried out by the Machine software is controlled. The voltage is set according to a given Time automatically delimbed when the machine is idle or after a cycle has been carried out. • Automatic version with CNC control in the X-TECH 900 / 1200 models a feed length of 500 mm for the series for high production rates. • The material is carried by a table with seven rollers. These will driven by a hydraulic orbital motor through which the material can be placed precisely even under maximum load. • All guided movements are carried out by four recirculating ball guides with one high capacity for static and dynamic loading; strong reduced feed friction. Tempered and ground prismatic Guides. Price on request.

Condition: excellent (used), Year of construction: 2011, The 2-axis WP CNC-T cleaning machine is an excellent example of a device that combines a machine built on the basis of the most modern components with high efficiency and the most favorable price. This machine operates on the basis of linear motor technology (magnetic cushion), allowing for long-term operation of the device. The set of tools with which the machine is equipped allows for cleaning the most common PVC profiles on the market. The basic machine is a strong, stable frame made of structural steel. The control panel is equipped with a PC computer. Basic equipment: Working arm: The working arm is driven by a linear motor (no clutches, gears, racks, lead screws). The linear motor moves at a set distance from the magnetic strip - no friction!! Linear motors (for the "X" and "Y" axes) are numerically controlled. Air cushion the working arm weighing several dozen kilos during the movement in the "Y" axis is supported by a pneumatic actuator - it constantly supplies pressure of a fixed value, which balances the weight of the arm. This solution allows for the use of short working times without the need to expose the machine components to the risk of rapid destruction. Control panel Independent control panel with a PC computer The operator menu is described by function keys - ease of use in production conditions. from the control panel, you can easily make corrections to the outline of the profiles (it takes the operator about 1 to 2 minutes to make the correction) Other data: Automatic system for cleaning the working surface Automatic clamping and centering of the material Minimum and maximum height of the processed profile: 40 - 150 mm Minimum and maximum width of the processed profile: 40 - 130 mm Minimum size of elements: external 340x400 mm VP - transport packaging BASIC SET OF UPPER AGGREGATES: working unit for tools for cleaning flat surfaces with a groove working unit for cleaning the surface of the glazing bead groove drilling unit for the gasket BASIC SET OF LOWER AGGREGATES: Njdewhu Hhspfx Aa Ejlk working unit for tools for cleaning flat surfaces with a groove working unit for cleaning the surface of the glazing bevel drilling unit under the seal ADDITIONAL SET OF LOWER AND UPPER AGGREGATES: working unit with a knife for cleaning flat surfaces without a groove working unit with a knife for cleaning flat surfaces without a groove

Condition: excellent (used), Year of construction: 2008, table length 4000 mm table width 1500 mm burner heads 1 Control SIEMENS 840D Capacity 6000 Watt speed 10 m/min Nedpfx Aaeu N I Erj Eolk weight of the machine ca. 19 t dimensions of the machine ca. 9,5 x 7,3 x 3,1 m This Trumpf TrueLaser Cell (TLC) 7040 with 6 KW is a 5-axis laser machine. Description: - Max. Sheet thickness: ST:20mm / VA:20mm / AL:15mm - Closed machine room - Laser TruFlow 6000 - ADC cutting head - Positioning laser diode - Suspended control panel stationary, rotatable - Teach panel - Magnetic coupling, head detection - Laser power control - Power cycles - Laser welding

Year of construction: 2021, condition: new, Single-head cutting machine OMC RONDA 700, new Machine in stock - saw blade D 700 mm Nledpfx Ashrukiea Eek - hydro-pneumatic feed - inclination is pneumatic on both sides, with fixed graduations of 22.5° - 45° - 90°. For intermediate gradations, with manual mechanical stop - 2 vertical and 2 horisontal clamps - spray mist blade lubrication system - integral pneumatic protection

Year of construction: 2020, condition: refurbished (used), 2 semi-gantry cranes for indoor operation expandable to full gantry crane Nlodpfemdrt Sox Aa Esk span approx. 8.5 m hook paths approx. 6,0 m DEMAG monorail trolley Floor control system

Year of construction: 2020, condition: refurbished (used), Dear customers! Our experience has shown that the communication by e-mail usually drags out everything unnecessarily. We would like to help you quickly, but it is better to spend three minutes on the phone than three days writing e-mails back and forth. T.S.W.C. 30.20 Dry bulkhead Dimensions: 3000 x 2000 mm W X H + Fan in the height Nsdpfsfn Nddex Aa Eelk Air capacity: 10.800 m³ / h Motor: 2,20 kW ex-proof Exhaust air pipe: 500 Ø mm depth: 900 mm Double filtration: paper filter + Paintstop filter mat over Terminal strip (+180,- EUR net) Options/additional price for: Paintstop filter mat terminal strip: 180,- EUR net side baffle plates with hinge: 590,- EUR net Pictures may vary. We can also offer you complete spraying rooms with supply air system, heat exchanger, supply air ceiling, piping etc. Just contact us.

Year of construction: 2021, condition: new, Single-head cutting machine OMC GIOBI 600, new Machine in stock - saw blade D 600 mm - hydro-pneumatic feed Nsdpfxohrumas Aa Eslk - inclination is pneumatic on both sides, with fixed graduations of 22.5° - 45° - 90°. For intermediate gradations, with manual mechanical stop - 2 vertical and 2 horisontal clamps - spray mist blade lubrication system - integral pneumatic protection

Year of construction: 1976, condition: good (used), strip width: 300 - 1.350 mm strip thickness: 0,35 - 3 mm coil weight: 12,5 t Njdpfx Aobh Ubwoa Eslk mandrel Ø: 508 mm

Condition: new, Year of construction: 2025, functionality: fully functional, machine/vehicle number: sn. 816, feed length X-axis: 2,600 mm, feed length Y-axis: 1,300 mm, total width: 4,000 mm, total length: 3,600 mm, total height: 3,500 mm, warranty duration: 12 months, cutting height (max.): 1,300 mm, space requirement length: 4,200 mm, space requirement width: 4,500 mm, space requirement height: 3,600 mm, Polish manufacturer of machines and equipment for cutting and processing polyurethane foam with over 25 years of experience offers for sale a brand-new automatic horizontal cutting machine, Model: TYPE PARK. The machine features a stable and robust steel construction. Cutting is performed by the movement of the cutting frame along the X and Y axes, while the table remains stationary. The cutting frame is driven by two reinforced toothed belts and moves on linear bearings along the X-axis. In the Y-axis (up and down movement of the frame), the feed is powered by two ball screws and linear bearings. The machine supports both single-sided and double-sided cutting modes and includes an automatic cutting correction system for double-sided cutting. Machine equipment includes: Automatic, self-adjusting saw blade tensioning system Stationary table with powered conveyor belt for easy material loading Automatic cutting length measurement Quick-change system for the saw blade Automatic material clamping system Working parameters: Cutting width: 2100 mm Cutting length: 2500 mm The machine is fully enclosed with safety fencing and equipped with safety light curtains at the loading and unloading zones. As the manufacturer, we provide installation and servicing within the EU. The machine is CE certified. We also offer a wide range of machines and devices for cutting foam and mineral wool. Nledpfx Aewq Dvdoa Esk We invite you to explore our full range of products.