Tool cutter

Deckel FP3 L Aktiv

Condition: reconditioned (used), Year of construction: 1988, Universal tool milling machine Make: DECKEL Model: FP 3 L Active Year of manufacture: unknown - overhauled, repainted, RAL7035 light gray / RAL7012 basalt gray RAL5008 gray-blue Mach. no.: 2302-2319 Milling head type: 2271 Milling head number: 700-0883 with guarantee geometric acceptance with test report Accessories: - 3-axis active digital display HEIDENHAIN TNC 111 - Universal table 1000 x 520 mm (T-slot: 16 mm) - Vertical milling head SK 40 with Tightening thread S 20 x 2 - Central lubrication, electric - Coolant system - Operating instructions - Drill grinding device with diamond disk Bodpjh Rv U Eofx Afnowh -used, as seen-

Condition: reconditioned (used), Year of construction: 1999, Universal Tool Milling Machine TOS FNGJ 32 3-axis Heidenhain digital readout Year of manufacture: 1999 Travel: X 600 Y 400 Z 400 mm Spindle speed range: 40 – 2000 rpm Supplied with the following accessories: Fixed angle table, 800 x 400 mm clamping surface Vertical milling head Extendable quill Various SK 40 tool holders Safety guard Chip tray Bwodjxc It Iopfx Afnoh Machine lamp Automatic central lubrication pump for X, Y, Z axes Coolant system 4 machine leveling pads

Condition: like new (used), Year of construction: 2013, functionality: fully functional, Universal milling machine Deckel FP2 repowered by FPS built in 2013 with 3-axis digital readout Heidenhain ND 780 As good as new !!! Technical data: >> Machine no. 2202-7020 FPS no. 3364 Year of construction 2013 >> Rigid angle table >> Speed: 40 - 2000 rpm >> Feed and rapid traverse in 3 axes >> Drive power .:2.2 KW >> Travel X/Y/Z: 400/200/400 mm >> Equipment: Vertical & horizontal spindle >> Vertical quill and horizontal quill extendable - SK- 40 >> Tightening system S20x2 >> Weight approx. 1100 kg Accessories and equipment: >> 3-axis digital readout Heidenhain ND 780 Bwedpfx Ajvbifgofneh >> Brake motor with immediate spindle stop >> Central lubrication >> 2 x emergency stop >> Operating instructions >> Coolant device To the machine : We offer a universal milling machine Deckel FP2 repowered by FPS in mint condition. The Deckel is equipped with a brake motor for immediate spindle stop. The machine has an electric central lubrication system. With two emergency stop switches for safety. Mechanically and electrically tested as of 2013. The Heidenhain digital display makes work easier and even more accurate. Take the opportunity to inspect and try out the lids under power on site. The machine is available immediately.

Year of construction: 2001, condition: used, Cazeneuve Maxica 590 With collet Control: SOMAB NUM SP + S 5 Bsdpfeh Aylvjx Afnewh

Condition: like new (used), Year of construction: 2021, functionality: fully functional, This multi-axis CNC lathe, CMZ TTL-66-66-T1Y-T2Y, was manufactured in 2021. It features a maximum bar capacity of 66 mm (both spindles), a turning diameter of up to 220 mm, and a main spindle power output of 35.5 kW. The machine is equipped with two high-performance spindles with a 66 mm bar passage, two turrets with 12/24 tool stations, driven tools with 14 kW and 12,000 rpm, and Y-axis capability on both the upper and lower turrets. It includes a 35-bar high-pressure coolant system, complete with a filtration system and an additional tank. For more information about this lathe, please refer to the attached brochure or contact us directly. Equipment includes: - LPS for left spindle - Reduction tube for left spindle - Hainbuch AXFIX 65 collet chuck (standard) 2703/0008 for left spindle - Hainbuch AXFIX 65 collet chuck (standard) 2703/0008 for right spindle - Tool presetting device - Side-mounted chip conveyor (standard version) - Upper tool turret (T1) high-pressure coolant pump with three programmable pressure levels (35, 15 & 6 bar), including 75µm filter - Lower tool turret (T2) high-pressure coolant pump with three programmable pressure levels (35, 15 & 6 bar), including 75µm filter - Coolant wash nozzle - TA/06000/10 8,000W coolant chiller unit - Machine status indicator light Bsdpfxjxmhdnj Afnjwh - Tool life management system - Tool load monitoring - Programmable automatic parts catcher (pneumatic) - The workpiece extractor is equipped with a pneumatic gripper for automatic opening and closing to retrieve finished parts - Pneumatic ejector for the sub-spindle with 100 mm adjustable stroke. End position detection via sensor - Coolant supply through right spindle - Interface for bar feeder (unimag) - Preparation for extraction unit, connection flange Ø100 The machine comes complete with a chip conveyor, coolant unit, and tool package. It is available for immediate inspection under power, and available at short notice. Single-shift operated. Further information available on request.

Condition: good (used), Year of construction: 2000, functionality: fully functional, drilling capacity: 40 mm, quill stroke: 200 mm, quill diameter: 80 mm, Machine design - Work table 1800 x 600 mm with 4T-slots - Boom travel 1050 mm - SK 40 drilling spindle with tool clamping device - Infinitely variable speed programming - Infinitely variable quill feed via three-phase servo motor - 2 T-slots 18 mm on the machine base at the rear - 2 T-slots 18 mm on the left machine base frame - Thread cutting device - Central lubrication - Coolant device - Machine light - CE marking Bodpfxeu Aa I Sj Afnswh - Safety device - USB interface Dimensions and travels Tool holder SK 40 Column diameter mm 195 Table dimensions mm 1800 x 600 Number of T-slots 4 Distance between T-slots mm 125 Quill stroke (Z-axis) mm 200 Column stroke (W-axis) mm 410 Distance spindle bottom edge - min mm 70 Table top edge max. mm 680 Distance spindle bottom edge - min mm 970 Floor max. mm 1580 Drilling radius mm 540 - 1590 Worktable height mm 900 Cutting values Drilling capacity into solid St 60  40 GG 22  50 Thread cutting St 60 M 36 GG 22 M 42 Main spindle drive AC motor, frequency-controlled kW 5.5 at 100 % duty cycle. Speed range: min -1 15 - 2800 Torque Nm max. 250 constant from min -1 15 - 2000 Feed drives X-axis - AC - servo motor kW 0.25 Y-axis - AC - servo motor kW 0.25 Z-axis - AC - servo motor kW 4.50 W-axis - AC - servo motor kW 2.50 Rapid traverse speeds (X/Y/Z): m/min. 7.5 / 7.5 / 5 Rapid traverse speeds (W): m/min. 3 Feed rates stepless mm/min 5 - 2000 Accuracy Positioning accuracy X-, Y-axis to 1200 mm mm ± 0.075 Electrical data Operating voltage / frequency V / Hz 400 / 50 Control voltage V 24 Hydraulic unit for clamping kW 0.75 Total connected load kVA 13.0 Weight Danumeric 440 (without packaging) with table 1800 x 600 mm kg 2800 CNC control Axes: 4 (X, Y, Z, W), expandable Processor: 32-bit CPU Screen: TFT flat screen, backlit, easy to read from all sides legible from all sides, 215 x 160 mm Position information: Cartesian or polar, absolute or incremental measurements, Unit of measurement: mm or inch or in degrees Interpolation: 2 axes (X, Y) Technology database: tool management, tool suggestions according to machining type, material-dependent cutting data suggestions Tool management: max. 500 tools Subroutine technology: yes Machining cycles Standard software options: Programming in dialog, 38 zero offsets, rotation and mirroring, teach-in for X, Y, Z, restart in program with selection functions for targeted entry Zero point determination: Cycles for determining zero points by manually probing the workpiece for by manually probing the workpiece for: - any clamped rectangular parts - any clamped round parts - Mediation of cast and flame-cut parts - Angular position detection for round parts by touching reference edges or surfaces Test graphics Graphic display of drilling patterns Data interfaces USB

Condition: new, Year of construction: 2025, Completely refurbished machine, as new, modernized to the legally prescribed "state of the art" safety standard in accordance with the safety regulations of the employers' liability insurance associations. Switch cabinet electronics Installation of a new CE - control cabinet according to the current legal regulations of the professional associations BGVA 3 / DIN-EN 60204-1 new machine standard. Optionally complete machine in CE execution. A CE declaration of conformity is issued for the machine. With this FPS Werkzeugmaschinen GmbH acts as manufacturer. The machine fulfills the requirements of the BETRIEBS-SICHERHEITSVERORDNUNG- Betr.SichV. The year of manufacture corresponds to the date of delivery of the machine. EN ISO 12100, EN ISO 13857, DIN EN 13128:2009-09, EN ISO 13850, EN ISO 13849, EN 60204-1 Control system 3-axis - FPS Active - digital display Speed 25 - 2500 rpm geometrically stepped direct gear with 18 speed steps for maximum torque / milling power Feed rate 5 to 500 mm/min, infinitely variable rapid traverse 1,2 m/min quill Extendable quill, vertical 100 mm SK40 with M16 tightening thread optional: with DECKEL - saw thread S20 x 2 Extendable quill, horizontal approx. 100mm Axes X/Y/Z 800/300/400 mm Table rigid angular table 1000x440mm, load 2000kg Equipment Bwsdpfx Ash Sptnsfnsh - Vertical and horizontal spindle - Milling head manually tiltable +/- 90 °. Options - Z-axis bellows - chip tray - machine light - central lubrication - universal table - rotary table - Shaper head - dividing head - counterholder - etc.

Condition: used, CNC cycle controlled lathe HARRISON type Alpha 400 Plus Machine No. P30180/150 Year of construction 1998 center distance 1250 mm turning diameter over bed 400 mm center height 200 mm Swing diameter over cross slide 245 mm Swing diameter in the bend 585 mm bed width 313 mm face travel (X-axis) 250 mm Tailstock spindle diameter 73 mm Tailstock quill stroke 140 mm Tailstock quill mount MK 5 spindle bore 54 mm spindle head size Camlock D1 size 6 Spindle speed 20-2500 rpm. Spindle speed range (stage 1) 15-275 rpm. Spindle speed range (stage 2) 35-795 rpm. Spindle speed range (level 3) 110-2500 rpm. Feed rate X and Z 0.03 - 0.6 mm/rev. Rapid traverse speed X axis max. 2000 mm/min. Rapid traverse speed Z-axis max. 4000 mm/min. Threading function Metric / Inch / Diametral / Module Spindle drive power 7.5 KW Mains connection 400 Volt, 50 Hz, 23,5 kVA - cycle control Harrison Alpha / GE FANUC - language in French (France) - automatic gear range shifting in 3 steps (15-275, 35-795, 110-2500 rpm.) - electronic handwheels with different transmission ratios (1/10/100) - 3-jaw face spiral lathe chuck FORKARDT Ø 250 mm type CSN, 1 set of soft top jaws - quick-change tool holder MULTIFIX size B with 2 inserts - 1 piece of centering point running with the tool - 1 piece quick-action drill chuck RÖHM, 3-16 mm - hinged lathe chuck guard - hinged working area protection doors Bwedpfx Aeh Hvk Aefnjh - chip tray with coolant device under the machine bed - Switch cabinet fixed to the machine - Interface RS 232 Space requirement L x W x H 2600 x 1450 x 1550 mm weight 1950 kg good condition

Condition: refurbished (used), Year of construction: 2025, functionality: fully functional, machine/vehicle number: 7/61, Manufacturing origin Swiss Voltage 380/50/3 Netweight abt. 760 kg Dimensions abt. 1250x1000x1700 mm TECHNICAL DATA WORK CAPACITY Travel X and Y 200x200 mm Vertical slide travel 250 mm Travel of drilling spindle 70 mm Max free passage between table and spindle nose 330 mm Free passage between column and centre of spindle 260 mm Max drilling capacity (steel) 10 mm Max reaming capacity 50 mm TABLE Usable surface 400x300 mm Admitted load 100 kg Travels X and Y through motors Number of T-slots 6 (longitudinal) DRILLING HEAD Spindel morse taper 0 Bedpfjd Amgkex Afnswh Speed of spindle 150-3000 rpm Feed of drilling spindle 0,015 mm/t PRECISION Direct reading on divided drums 0,01 mm Direct reading on verniers 0,001 mm Guaranteed precision on displacement of slide-way 0,002 mm MEASURE Measuring system direct, optical Elements of measure graduated rule, div.1mm Read-out projection screens Shifting of zero-point yes Direct read-out 0,001 mm Guaranteed positioning precision 0,002 mm Installed power 1,2 kW errors and omissions excepted data given without obligation Inventory Nr.2160006, machine equipped with : 1 turning table Ø 220 with optical measure 1 centering microscope with 3-points suspension, zoom 40x, lightening 1 centering device with dial comparator cap. 3 mm. MT0 1 centering point MT0 1 tracing tool with spring-mounted point MT0 1 center punch MT0 1 chuck for centering drills MT0 1 self clamping drill-chuck 0-5 mm., MT0 1 boring head type 0, cap. 0.5-30 mm., MT0 1 levelling foot with 2 round levelling supports

Condition: good (used), Year of construction: 1997, functionality: fully functional, drilling capacity: 40 mm, quill stroke: 200 mm, quill diameter: 80 mm, Machine design - Work table 1800 x 600 mm with 4T-slots - Boom travel 1050 mm - SK 40 drilling spindle with tool clamping device - Infinitely variable speed programming - Infinitely variable quill feed via three-phase servo motor - 2 T-slots 18 mm on the machine base at the rear - 2 T-slots 18 mm on the left machine base frame - Thread cutting device - Central lubrication - Coolant device - Machine light - CE marking - Safety device - USB interface Dimensions and travels Tool holder SK 40 Column diameter mm 195 Table dimensions mm 1800 x 600 Number of T-slots 4 Distance between T-slots mm 125 Quill stroke (Z-axis) mm 200 Column stroke (W-axis) mm 410 Distance spindle bottom edge - min mm 70 Table top edge max. mm 680 Distance spindle bottom edge - min mm 970 Floor max. mm 1580 Drilling radius mm 540 - 1590 Worktable height mm 900 Cutting values Drilling capacity into solid St 60  40 GG 22  50 Thread cutting St 60 M 36 GG 22 M 42 Main spindle drive AC motor, frequency-controlled kW 5.5 at 100 % duty cycle. Speed range: min -1 15 - 2800 Torque Nm max. 250 constant from min -1 15 - 2000 Feed drives X-axis - AC - servo motor kW 0.25 Y-axis - AC - servo motor kW 0.25 Z-axis - AC - servo motor kW 4.50 W-axis - AC - servo motor kW 2.50 Rapid traverse speeds (X/Y/Z): m/min. 7.5 / 7.5 / 5 Rapid traverse speeds (W): m/min. 3 Feed rates stepless mm/min 5 - 2000 Accuracy Positioning accuracy X-, Y-axis to 1200 mm mm ± 0.075 Electrical data Operating voltage / frequency V / Hz 400 / 50 Control voltage V 24 Hydraulic unit for clamping kW 0.75 Bodpfx Aformkfnsnswh Total connected load kVA 13.0 Weight Danumeric 440 (without packaging) with table 1800 x 600 mm kg 2800 CNC control Axes: 4 (X, Y, Z, W), expandable Processor: 32-bit CPU Screen: TFT flat screen, backlit, easy to read from all sides legible from all sides, 215 x 160 mm Position information: Cartesian or polar, absolute or incremental measurements, Unit of measurement: mm or inch or in degrees Interpolation: 2 axes (X, Y) Technology database: tool management, tool suggestions according to machining type, material-dependent cutting data suggestions Tool management: max. 500 tools Subroutine technology: yes Machining cycles Standard software options: Programming in dialog, 38 zero offsets, rotation and mirroring, teach-in for X, Y, Z, restart in program with selection functions for targeted entry Zero point determination: Cycles for determining zero points by manually probing the workpiece for by manually probing the workpiece for: - any clamped rectangular parts - any clamped round parts - Mediation of cast and flame-cut parts - Angular position detection for round parts by touching reference edges or surfaces Test graphics Graphic display of drilling patterns Data interfaces USB