Spot welding gun

DALEX 3427 D

Year of construction: 2024, condition: new, Make: DURMA Type: MS 2504 year of manufacture: 2022 cutting length: 2550 mm sheet thickness: 4 mm Control: EZM9910 Operating hours: 0 Cutting angle: 1°30 Strokes per min.: 42 motor power: 7,5 kW backgauge range: 750 mm table width: 450 mm table height: 800 mm dimensions L/W/H: 3200x2300x1350 mm Weight: 3780 kg Standard equipment Gijdpfjd R Er Dex Afnsn control unit EZM9910 backgauge range 750 mm programmable via control unit Jvcmke Plastic inserts for hold-down 1 side stop and 2 sheet support arms Finger guard Portable foot switch with emergency stop Spring loaded stop in T-slot of the support arms Ball screw Ikh7877 Table plates with ball rollers Upper knife with 2 cutting edges Lower knife with 4 cutting edges CE marking Extended equipment Adjustable angular fence 0-180 The machine can be inspected and demonstrated at any time by appointment in our demonstration center in Staufenberg. Further machines are ready for demonstration at our facility in Staufenberg. We will be happy to provide you with further information on request.

Condition: used, Miter cold circular saw KALTENBACH type KKS 400 NA Machine. No. 101701 Year of construction 1983 saw blade diameter 400 mm cutting range at 90° round Ø 130 mm sawing range at 90° square 120 x 120 mm sawing range at 90° rectangle 305 x 20 mm Cutting range at 45° round Ø 130 mm Sawing area at 45° square 110 x 110 mm Cutting range at 45° rectangle 245 x 30 mm Clamping range of collet feed 30 to 140 mm Working height 1000 mm miter cut 0 - 180 feed path 600 mm Saw blade speed 10 + 20 m/min. 2 steps motor power 1,7 and 2,6 kW hydraulic motor 1,5 kW Mains connection 380 Volt, 50 Hz - Hydraulic material clamp feed with infeed roller conveyor left 1500 mm - Feed path via double feed up to 1200 mm (2x feed, then sawing) - Hydraulic material clamping with vertical clamping cylinder - miter cut - saw angle with manual adjustment - hydraulic feed control, cutting speed manually adjustable - 2 motor speeds for the saw blade speed - saw blade stroke steplessly adjustable - coolant unit with electric pump in the machine base - Hydraulic unit fixed to the basic machine - Parts counter with zero cut-off Giedpjd N H A Nofx Afnsn space requirement of the saw 2600 x 1200 x 1900 mm weight of the saw approx. 1400 kg good condition

Condition: used, Year of construction: 1980, saw blade diameter 380 mm pneumatic clamping ja 46893 weight of the machine ca. 1,3 t +++++ Please note: The machine is dismantled and ready for loading. It is not possible to show it under power or make a video. Gijdpod N Sm Dofx Afnsn Our offer includes already the best pictures. So we don’t have and won’t send additional pictures. +++++

Condition: used, Year of construction: 1979, cutting diameter 440 mm weight of the machine ca. 780 kg +++++ Please note: Gisdpfx Afef Dwa Usnsn The machine is dismantled and ready for loading. It is not possible to show it under power or make a video. Our offer includes already the best pictures. So we don’t have and won’t send additional pictures. +++++

Condition: used, Year of construction: 1991, sheet width 2050 mm plate thickness 3.5 mm distance between columns 2100 mm stroke of upper beam 250 mm adjustment UW 80.0 mm work height max. 920 mm total power requirement 6.0 kW weight 2910 kg range L-W-H 3185 x 875 x 1450 mm Features: - Robust electric-driven folding machine - With dynamic, powerful drive motors - Manual/automatic operation selectable - Control panel, right front - Bending angle preselection via electric potentiometer - Manual lower beam adjustment - 1x used upper tool rail - 2x used lower tool rails - 1x freely movable double foot switch - Original operating instructions Gisdpsw U U Ukefx Afnen

Year of construction: 2002, condition: good (used), Make: Matsuura Type: LX-O Control: YASNAC Year: 2002 Specifications Metric US Standard X - Travel 330 mm Y - Travel 300 mm Z - Travel 250 mm Table Length 540 mm Table Width 320 mm Table load 100 Feed rate X-Axis 90000 mm/min. Feed rate Y-Axis 90000 mm/min. Feed rate Z-Axis 90000 mm/min. Spindle Taper 30 ISO/Bt/Mk Power on spindle 7.5 kW Speeds / ranges 40000 Rpm Gjdelz Rvlopfx Afnjin ATC / revolver 30 Chip conveyor Yes Dimensions (Estimate) Length 2800 mm Width 2600 mm Height 28000 mm Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!

Year of construction: 1991, condition: like new (used), overall weight: 1,420 kg, rotational speed (max.): 1,485 rpm, 3 stainless steel volute casing pumps in process design 2 x CPK-CM 250-315 built in 1991 1 x CPKN-C1 250-315 year of construction 2011 !!! Price per piece !!! Pumps were operated on a test bench and all have very few operating hours! See pictures !!! Flow rate: 1001 m³/h (278 liters / second) Delivery head / delivery pressure: 18 m / 1.8 bar Pump speed: 1485 1/min NPSH: 5.00 m Shaft seal: single mechanical seal with sealing water Manufacturer: Burgmann Impeller type: closed centrifugal impeller Impeller diameter: 324mm Bearing type: roller bearing Lubrication type: Oil Lubricant monitoring Oil level controller Materials: 1.4408 (AISI 316) Pump housing: 1.4408 (AISI 316) Wear plate: 1.4408 (AISI 316) Gsdpfsqabiaox Afnsin Pressure cover: 1.4408 (AISI 316) Shaft: Heat-treated steel C45+N Impeller: 1.4408 (AISI 316) Bearing bracket lantern: Gray cast iron JL1040 Shaft sleeve: CrNiMo steel Nominal diameter of suction nozzle: DN 300 Discharge connection Nominal diameter: DN 250 Nominal pressure suction side: PN 16 Nominal pressure pressure side: PN 16 Coupling manufacturer: Flender Coupling type: Eupex NH without intermediate sleeve Base plate: Painted gray cast iron Motor manufacturer: VEM K21R 280S4-Z Efficiency class: IE 0 Motor speed: 1480 1/min Frequency: 50 Hz Rated voltage: 400 / 690 V Rated motor power: P2: 75 kW Thermal class: F Motor protection class: IP55 Cosphi: 0.86 Dimensions: Length: 2120 mm Width: 950 mm Height: 1090 mm Weight: 1420 kg

Condition: used, Year of construction: 1998, machine/vehicle number: 100057, 1998 AMADA VIPROS 2510 KING The punching machine is in good condition, always serviced on time by Amada service. All documentation is included. This machine can be operated with a punching force of 196 kN. Made in Japan. The punching machine is still under power and can be tested at any time in Vilnius, Lithuania. Specification: Model: AMADA VIPROS 2510K Serial no: 100057 Gedpfsm Ncaysx Afnsin Year: 1998 Made in: Japan Punching force: 20 tons Stations: 31 Tools: included (RO 6; RO 6,5; RO 3; RE 30x5; RE 25x5; RE 80x5; RO 5; RO 3,5; RE 10x3; RE 10x5; RE 50x5; RE 8x12) Maximum sheet thickness: 3 mm X-axis movement: 2500 mm Y axis travel: 1270 mm Weight: 11 000 kg Location: Vilnius, Lithuania Testable: Yes If you have any questions, please do not hesitate to contact us.

Condition: new, Year of construction: 2021, functionality: fully functional, Stock machine "NEW" – available at short notice! (Subject to prior sale) Control: Fanuc 0i-MF Plus, 10.4" with Manual Guide i & 2 MB NC memory LOOK-AHEAD function, 400 blocks Machine Table: Table size: 950 x 550 mm Load capacity: 800 kg T-slot width: 18 mm Number of T-slots: 3 Distance between T-slots: 150 mm Travel axes: Travel X/Y/Z: 860/550/550 mm Spindle nose to table surface: 150 – 700 mm Linear guides & speeds: Ball linear guides in X/Y axes Roller linear guide in Z axis Rapid traverse X/Y/Z: 40/40/30 m/min Feedrate during milling: 0 – 10,000 mm/min Smallest increment: 0.001 mm Gisdpfxoifn N No Afnjn Tool magazine (CAM-Type) / changer: Number of magazine pockets: 30 System: random access Max. tool diameter: Ø 75 mm Max. tool diameter with adjacent pockets free: Ø150 mm (40 tools: Ø130 mm) Max. tool length: 300 mm Max. tool weight: 7 kg Spindle: Spindle taper: SK-40 Drive power (30min/cont.): 18.5/11 kW 15,000 rpm direct-drive spindle Spindle oil cooler Coolant, chip, and compressed air management: Coolant system incl. 300 liter tank and pumps External coolant around spindle Chip augers right and left in machine bed Compressed air nozzle at spindle (M32/M33) Compressed air through spindle (M38/M39) Compressed air and coolant gun Other features: Swiveling operator panel Electronic handwheel (wired) Central lubrication oil/air Full enclosure Work light Heat exchanger at control cabinet Auto power-off function Hand tool set Signal lamp Transformer 400 VAC, 50 Hz CE declaration of conformity according to European directives Electrical and pneumatic requirements: Electrical connection: 36 kVA Required pneumatic input pressure: 6 bar Dimensions: Machine size: W2,260 x D2,900 x H2,775 mm Required installation area: W3,160 x D3,000 x H3,000 mm (incl. chip conveyor ejection to the left) Machine weight: approx. 5,400 kg (net) Available special equipment: Spindle: - Direct-driven spindle SK-40, 15,000 rpm - Drive power (30min/cont.): 18.5 / 15 kW, (FANUC motor) Tool magazine / changer: - Drum-type tool magazine with 30 pockets, DIN69871, SK-40 Rotary or additional axes: - Preparation for 4th axis (FANUC controls), incl. wiring and Harting connector, without axis drive Coolant, chip, and compressed air management: - Bed flushing - Through-spindle coolant pump, 20 bar pressure, for direct-driven spindles - Includes cartridge filter - Belt-type chip conveyor including chip cart (chip discharge at front, to the left side of the machine) Measuring and monitoring systems: - RENISHAW OMP-60 probe with infrared transmission system for workpiece measurement, incl. probe holder, repeatability: 1μm - RENISHAW NC4+ tool laser measurement system and tool breakage monitoring in the machine, incl. bracket - Auto-door (side door) - Pneumatic interface for workpiece clamping - Clamping devices as shown With RoboJob Mill Assist 25kg (Year of construction 2025 – NEW) - Full enclosure - Double gripper Available immediately

Condition: good (used), Year of construction: 2003, Good condition,live tools, measuring arm. Godpfxswybg So Afnoin Parts shown by hand not come. Technical details shown on pictures.