Veneer pack guillotine shear

CASATI MACCHINE BIG 3200

Condition: ready for operation (used), functionality: fully functional, cutting length (max.): 3,550 mm, cutting width (max.): 530 mm, overall weight: 9,000 kg, stroke length: 100 mm, TECHNICAL DETAILS Usable cutting length (as double guillotine): 3,200 mm Usable cutting length (as single plate shear): 3,550 mm Press stroke: 100 mm Press width: 550 mm Min. cutting width: 18 mm Max. cutting width: 530 mm Scrap setting range: 0/50 mm Operating pressure: 6/7 bar MACHINE DETAILS Installed total power: 13.9 kW Lhodpfeyf Eucox Apmsi Dimensions & Weight Dimensions (L x W x H): 5,200 x 1,700 x 1,800 mm Weight: 9,000 kg EQUIPMENT Robust steel construction Blade beam made of cast iron Self-lubricating prismatic guides Adjustable rear support Press for holding the veneer package during cutting Photoelectric cells Electronic programming device Perimeter safety guards

Condition: used, No. 3213 Thermal treatment system / vacuum dryer WTT Used, year of construction 2017 Thermal treatment system / thermal chamber for the modification of wood The WTT thermal chamber is a system for the thermal modification of wood. It enables efficient treatment of 2 to 3 batches per day, depending on the thickness and type of wood. The system has a powerful energy and heat transfer system and works with a gas or oil-fired boiler system that uses thermal oil as a heat transfer medium. Technical data: Capacity: 5950 - 9900 m³ of wood per year (for 330 working days) Usable volume: 9 m³ (with 50 mm wood thickness) Stack dimensions: 10500 x 1300 x 1100 mm LWH Minimum board thickness: 10 mm Power connection: 3 x 400 V, 50 Hz + zero + earth, 63 A Specific power consumption: 15.9 kW/m³ Maximum heat output: 2 MW (230 °C - 250 °C thermal oil) Heat consumption: 120 kWh/m³ wood Autoclave length: 11,000 mm Autoclave diameter: 1,800 mm Autoclave material: 10 mm stainless steel duplex EN 4462 Door opens hydraulically, with 1.5 kW drive Working pressure: 0.1 to 15 bar (absolute) Working temperature: 0 °C to 220 °C 200 mm glass wool insulation, clad with 1 mm galvanized sheet steel Main components: 1. autoclave, in which the heat treatment takes place 2. vacuum system that sucks the air out of the autoclave before heat is applied 3. energy center with a 2 MW oil burner 4. 4 MW cooling system with dry coolers 5. nitrogen generator 6. gas cooler system Heating and cooling system: Heat exchanger: 8 units (4 on each side) Material: Stainless steel pipes (seawater resistant) Total floor area: 165 m² Cooling water consumption: 1000 l/batch (not contaminated, only heated) Control and operation: Control system: WTT ExoT (fully automatic) 22” color monitor, IBM computer, printer Sensors: 4 PT100 temperature sensors 2 mechanical thermometers 1 vacuum/pressure transmitter 1 mechanical vacuum/pressure gauge Special equipment: Hydraulic rail bridge for convenient transportation of wooden trolleys Automatic trolley extraction with cable winch (1.5 kW) 2 MW thermal oil boiler (heating) Fuel oil tank (4000 l) with measuring system Insulated 20 foot steel container for heating module Stainless steel safety chimney (300 mm diameter, 6000 mm length) Ledpfxev Si Szj Apmehi Functional description: 1. filling the autoclave with wood 2. creating a pre-vacuum 3. filling with gas 4. heating 5. modifying 6. cooling 7. pressure equalization 8. creating a post-vacuum / drying 9. pressure equalization 10. emptying Certified EC Pressure Equipment Directive (PED) 97/23/EF Construction EN 13445 Sale on behalf of customer, from location near 5020 Salzburg (Austria), without dismantling, transportation and assembly Dismantling, loading and transportation by us optionally possible Subject to errors in the description and price To avoid possible misunderstandings, an on-site inspection by appointment is possible and recommended Sold as is Technical details, condition description, year of construction and scope of delivery according to manufacturer's brochure or previous owner, without guarantee Subject to prior sale For used machines, any warranty is excluded, the following applies: “purchased as seen” Pictures and videos serve as examples and do not represent the actual scope of delivery Terms of payment: Prices excl. VAT, payment before collection or dispatch Terms of delivery: ex location

Condition: used, Year of construction: 2013, functionality: fully functional, Fisher+Rueckle FZR-24 Veneer cross-gluing machine, year 2013 for sale! Veneer strip length 400-1100 double lane/ 350-2100 mm single lane Veneer strip width 50-500 mm Veneer strip thickness 0.3-1.5 mm Max nominal output /machine cycles 30 cycles/min Average production speed 17-20 cycles/min Effective length of heating zone 2478 mm Connection power 22 kW Compressed air 6 bar Lhjdpoumrf Aofx Apmoi Glue types PVA or UREA based

Condition: excellent (used), Year of construction: 2001, Complete Parquet painting shop Manufacturer - SORBINI/ VIET Year - 2001 Ljdpfx Apsrdgrvomohi Capacity - 800 m2/shift Time of one cycle - 8 min. Lenght of the line - 42 m

Condition: used, Year of construction: 2020, max. workpiece length 3740 mm profile spindle 1 Stück main drive 15 kW Control CNC Felder Format4 Type Profit H500S 16.38 CNC Machining Center to be sold on behalf of our customer ----- - From a wood window manufacturing company. - Machine still connected and ready for demonstration - Without machining tools Technical description (summary, full text see PDF): ----- Working dimensions: X = 3,740 mm Y = 1,570 mm Z = 350 mm clearance height (from console level), depending on clamping system, see layout. Travel: X = 4,930 mm Y = 1,925 mm Z = 500 mm Axis positioning speed: X = 80 m/min Y = 80 m/min Z1 = 30 m/min Z2 = 20 m/min - 5-axis milling spindle: 15 kW HSK F63 with liquid cooling, 1,000 - 24,000 rpm - Additional C-axis locking - Drilling head DH 18 6H1S: Vertical drilling unit with 12 spindles (7 spindles in the X direction, 5 spindles in the Y direction, grooving saw in the X direction) Horizontal drilling unit with 6 spindles, 4 spindles in the X direction and 2 spindles in the Y direction. 1 groove saw in the X direction, max. diameter 120 mm - Tool changer with 24 tool positions on the right side of the machine stand max. workpiece diameter 240 mm max. tool height 370 mm - Tool changer for circular saw blade mounted on the boom/tool changer max. saw blade diameter 350 mm - Tool changer on the left side of the machine stand with 10 tool positions. Max. workpiece diameter 180 mm Max. tool length 230/300 mm Collet spacing 110 mm - 24-position tool changer mounted on the boom, moving in the X-direction Max. workpiece diameter 240 mm Lodpfx Aeyq Sztjpmehi Max. tool height 370 mm - Moving pick-up area for chip deflector plate - 6 workpiece supports with s-motion position control - 2 machining areas for pendulum machining - Vacuum pump 90 m³/h - Chip conveyor belt - Line laser for curved machining - Includes all existing solid wood clamps and vacuum suction cups - Automatic central lubrication - CE safety device - "WoodFLash" software Lamello Clamex P Macro Notching Macro software - "Greenline package" for reduced energy consumption ----- Price of the above machine on Inquiry! ----- NOTE VIDEO: Not an original video. The video is from the machine manufacturer and shows a machine of this type. (Technical specifications according to the manufacturer - without guarantee!) All prices quoted are net, plus VAT.

Condition: reconditioned (used), Number of spindles 6 St. Working width 230 mm Working height 120 mm Length of the planing table 2500 mm Feed motor 3 kW Feed speed 5-24 m/min. total power requirement 27 kw Dimensions (L/W/H) 3900 x 2200 x 2000 mm weight of the machine ca. 2500 kg Weinig Profimat 23 four-side planer, window version with glazing bead removal or can be used as a grooving spindle ATS control and program control ----- Machine was factory overhauled by Weinig in 2024. Technical Specifications Summary (Please inquire about any additional accessories included) ----- General ----- > Working width: 230 mm Lhedsxpn T Uepfx Apmji > Working height: 120 mm > Number of spindles: 6 > Planer table length: 2500 mm > Feed motor: 3 kW > Feed speed: 5-24 m/min > Total power requirement: 27 kW > Dimensions: 3900 x 2200 x 2000 mm > Machine weight, approx.: 2500 kg Spindle arrangement ----- > Spindle 1: bottom > Spindle 2: right, pneumatically timed up-down > Spindle 3: left > Spindle 4: top > Spindle 5: bottom > Spindle 6: pneumatically timed up-down glazing bead saw Spindle Description ----- > Spindle 1: 4 kW, 6000 rpm, 40 mm diameter > Spindle 2: 7.5 kW, 6000 rpm, 40 mm diameter > Spindle 3: 6000 rpm, 40 mm diameter > Spindle 4: 5.5 kW, 6000 rpm, 40 mm diameter > Spindle 5: 4 kW, 6000 rpm, 40 mm diameter > Spindle 6: glazing bead saw 2.2 kW, 6000 rpm, 40 mm diameter Additional Features ----- > Can be used for glazing bead cutting or as a grooving machine > ATS control, automatic 2-axis positioning for width and height (left and upper spindle) with 99-program memory > Machine operation: Window package Joint control of the right spindle and the glazing bead feed via manual selector switch on the control panel > Spindles with mechanical digital display (Technical data according to the manufacturer - no guarantee!)

Condition: good (used), Year of construction: 2020, Masterwood Project 351 L 3-Axis CNC machine Description Aircooled 3-axis milling motor 17,5HP (HSK-63F) Static frequency inverter for programming speed 1.500-24.000 t.p.m. Toolchanger with 22 positions Lsdpsvu U Itefx Apmehi 6 pneumatic countersinkable panel guides for loading/positioning heavy parts Prepared for install. clamps 2 horizontal clamps for beamwood 6 zero points over X-axis (positioning of panels at backside of the supports 8 zero points over X-axis (positioning of panels half-way the supports) Full reference at rightside over Y-axis Full reference at leftside over Y-Axis 2 workingfields 1 x 100m³ vacuumpump 24 vacuumcups Remote control with digital read-out Auto tool measuring system Transport waste belt Drill unit with 19 spindles (32mm center distance) 2,2kW - 7 vertical drillspindles in X-direction - 6 vertical drillspindles in Y-direction - 4 horizontal drillspindles in Y-direction - 2 horizontal drillspindles in X-direction (all drill spindles independently programmable) Control unit with PC SINCRO Software CAD/CAM MASTERWORK Technical specifiactions Working range in X - 5.130mm Working range in Y - 1.550mm Speed in X-Y 80 mtr./min. Speed in Z 25 mtr./min. Max. workpiece thickness 200mm Milling motor power 17,5 HP (S1) RPM milling motor 1.500 - 24.000 Drill unit 3HP Toolholdersystem HSK63-F Toolchanger 22 positions Vacuumpump 100m³ Dustextraction 250mm Aircapacity 4.500m³/h Airspeed 30 mtr./sec. Compressed air 7 bar Compressed air consumption 300-500ltr./min. Fuse value 40 Amp. Weigth 7.000kg (All changes, mistakes in technical data, info and prices reserved. Availability subject to prior sales. No guarantee on printed data!) (Alle Änderungen und Irrtümer in den technischen Daten, Angaben und Preisen sowie Zwischenverkauf vorbehalten! Keine Garantie auf gedruckte Daten!) Best woodworkingmachines from the Netherlands Holland Die besten holzbearbeitungsmaschinen aus die Niederlande De beste gebruikte machines uit Nederland

Condition: used, power: 210 kW (285.52 HP), first registration: 11/2007, fuel type: diesel, axle configuration: 4x4, fuel: diesel, color: white, gearing type: semi-automatic, number of gears: 8, emission class: euro4, Year of construction: 2007, Equipment: ABS, air conditioning, electric window regulation, onboard computer, power assisted steering, soot filter, trailer coupling, = Additional options and equipment = - Tachometer - Rear electric windows - Radio/CD player - Reversing camera Lodpfxsvk Nqns Apmehi = Further information = Number of cylinders: 6 Engine displacement: 6,374 cc Unladen weight: 8,663 kg Payload: 3,837 kg Gross vehicle weight: 12,500 kg Max. towing capacity: 10,000 kg (unbraked 750 kg) Interior: grey MOT (main technical inspection): New TÜV upon delivery Number of keys: 2

Condition: new, Year of construction: 2026, machine/vehicle number: SÇ 402 Alttan Çıkma Kesim Makinası, functionality: fully functional, • Compliant with CE standards. • Used for cutting aluminum and PVC profiles. • Hydro-pneumatic cutting operation. • Adjustable cutting speed according to the profile. • Capable of cutting at fixed angles to the right and left: -60, -45, -30, -22.5, -15, 0, +15, +22.5, +30, +45, +60 degrees. • Pneumatic vertical and horizontal clamps. • Ø550 mm diamond-tipped aluminum saw blade. • Equipped with roller conveyor (3 meters right and left). Lsdpfx Apjrahzgsmshi • Oil spraying system. • Enables precision cutting thanks to the 3 kW motor and Hydro-check. • For use with a digital measuring meter.

Condition: used, Bottle filling line with an output of 30,000 bottles/h. 0.33l Vichy, 0.33l Euro, 0.35l Frucade and 0.5l NRW single-use and reusable bottles are used. The system consists of the following machines/components: -Unpalletizing system Manufacturer: Radenska & Steinle -Unpacker Manufacturer: SZA Federspiel -New glass lifter Manufacturer: Steinle Fördertechnik -Uncorker Manufacturer: Rink -Bottle washing machine Manufacturer: Krones -Crate washer -Bottle inspector Manufacturer: Krones -Beer preheater Manufacturer: Fischer -Bottle filler Manufacturer: Krones -Crown cap filling bunker with magnetic transport Manufacturer: Gassner -Bottle level control Manufacturer: Metec -Labeler Manufacturer: Krones/Renner -Label control Manufacturer: Miho -Packer Manufacturer: SZA Federspiel -Full crate inspection Manufacturer: Metec -Bottle carrier unfolder -Palletizing and palletizing system Manufacturer: Radenska & Steinle Additional title: with palletising and depalletising, years of manufacture 1993 - 2009 Capacity: 30000 bottles/h Formats: 0,33 L Vichy, 0,33 L Euro, 0,35 L Frucade und 0,5 L NRW Running direction: anticlockwise Operation / Control: mainly Siemens S7 Features: Unpacking and palletizing system; unpacker; new glass remover; corker; bottle washing machine; crate washer; bottle inspector; beer preheater; bottle filler; crown cap feeder; fill level control; labeler; label control; packer full crate inspection; bottle carrier erector Layer patterns: 4x20, or 4x24, bottles, 4x8 boxes, 5 layers, on Euro pallet Lhjdpevu Tt Iofx Apmoi