Thicknessing machine

Brugg HDA-85

Condition: used, L + Z Lathe WEILER Type LZ PRIMUS GS Machine no. No. 2461 Year of construction approx. 1990 Center width 400 mm Turning diameter over bed 250 mm Center height above bed 125 mm Turning diameter over support 140 mm Center height above support 70 mm Spindle bore 24 mm Spindle speed 60 - 3000 rpm 18 steps Feed lengthwise and flat Chuck flange short taper DIN 55022 size 4 Inner tailstock taper MK 2 Drive power 1.1 kW and 1.5 kW pole-changing Mains connection 380 Volt, 50 Hz - 3-axis digital readout FAGOR, type 30i-T-B - Spindle speed via 2 motor speeds and 9 gear stages - 3-jaw lathe chuck RÖHM Ø 125 mm with stepped jaws Nodpfxertd Uwo Aa Eolk - MULTIFIX quick-change tool holder with 1 interchangeable cassette - Set of collets Ø 1 / 3 / 4 / 5 / 7 / 8 / 10 / 14 / 15 / 16 / 17 / 19 / 20 / mm - 1 centering tip for collet chuck holder - Emergency stop - Hinged chuck guard - Splash guard - Machine light - electrical diagram - Machine mounted on a steel plate (steel plate L x W x H 1200 x 500 x 30 mm, 140 kg) Space requirement L x W x H 1200 x 900 x 1560 mm Weight 520 kg good condition

Condition: reconditioned (used), Year of construction: 1986, cutting length (max.): 2,800 mm, cutting width (max.): 800 mm, cutting width at rip fence: 800 mm, main saw diameter: 450 mm, M.-No. 86-1-224, year built 1986, connected load 380V 5.5kW, trimming carriage length 2800 mm, cutting width 800 mm, hydraulic height and tilt adjustment, scoring unit, star-delta switch, parallelogram safety device with narrow and wide hood, angle stop, mitre stop, parallel fence, table extension 800 x 400 mm Nledpfxjwrb U Ts Aa Eok

Condition: new, Year of construction: 2025, crosscut and miter saw type: ZS 200 N - 5 KW motor with machine stand, but without saw blade Machine via handwheel and worm gear (rear) Tiltable Saw blade diameter 520 mm, saw blade mounting hole 50 mm Nsdpfx Aei Dfidea Eolk Saw blade speed: 2800 rpm 400 volt / 5 KW (S6/40%) motor with brake u. Automat. Star delta motor control cutting width at 90deg: 420 mm cutting width at 45deg: swivelled: 295 mm Cutting height at 90deg: 200 mm Cutting height at 45deg tilted: 140 mm Saw can be tilted on one side up to approx. 25 degrees to acute angles and tilted flat to the left up to 30 degrees Machine stitched: approx. 250 kg Location: ex stock 54634 Bitburg - immediately available -

Condition: used, Year of construction: 1995, Swivel spindle: Yes -5 to 45° Height adjustment: Handwheel Swivel adjustment: Handwheel Milling jaw adjustment: manual Height display: mech. counter Swivel angle display: mech. counter Milling stop display: mech. counter Milling spindle diameter: 30mm / new milling spindle Speeds: 3000, 4500, 6000, 9000 Motor power: 5.5 kW Motor brake: Yes, automatic Suction connection: 2 x 120mm Machine length: 2000mm Machine depth: 1400mm Nljdpfeuzkwzsx Aa Eek weight: 900kg

Condition: new, diameter 200 mm height 105 mm Nljdohuxbrepfx Aa Ejk weight of the machine ca. 25 kg dimensions of the machine ca. 400 x 280x 150 m

Year of construction: 1972, condition: ready for operation (used), Table Ø: 300 mm Njdpfx Asd Rlifoa Eelk Overall height in horizontal position: 155 mm Width: 500 mm Depth: 500 mm

Condition: new, diameter 200 mm height 105/265 mm centre height 105 mm weight of the machine ca. 41 kg Nljdpfjupxd Rox Aa Ejk dimensions of the machine ca. 400 x 330 x 310 m

Condition: excellent (used), Equipment: scorer, Electric adjustment of saw blade height and angle; scorer. You can call or write to us. We can speak and write in German and Russian. You can also send messages in English. Nedpfxow Ix Alj Aa Eelk

Condition: used, Multifunction machine Adolf 1.Saw 2.Equalizer Nedpfx Asu E Icpea Ejlk Width 500mm 4 knife shaft Tops length 195cm 3.Chiseling-drilling machine Weight of the machine 750kg

Condition: used, with mounted three-jaw chuck table-Ø: 200 mm bore approx.: 18 mm Nlodpfx Aajda I Rvj Eek overall height: 100 mm total height with chuck: 165 mm width: 270 mm length: 320 mm