Band saw

Bomar Individual 720.540 GH

Condition: new, capacity 90 degrees: round 350 mm capacity 90 degrees: square 330 mm 500 x 310 band speed 15 - 100 m/min table height 844 mm dimensions of saw-band 4250 x 34 x 1,1 mm total power requirement 2,2 kW weight of the machine ca. 1,2 t dimensions of the machine ca. 1,4 x 2,4 x 1,935 m ACTION PRICE!!! 2-column double miter band saw K-tech DG 50/33 HA-I • 2-column miter saw • Solid, yet easy to use • Material height sensor (automatic cut start detection) • Smooth running thanks to bevel cut, feed controller + cutting pressure controller • Massive material infeed roller • Removable chip tray (disinfection) • Energy-saving and low-vibration thanks to bevel cut • Ergonomic, safe and free-standing control panel Gisdpfofg E Hlox Admjl • Frequency-controlled saw drive 15 -100 m/min. • Hydraulic cutting pressure control valve • Hydraulic control of saw frame and vice • LEDs for monitoring all safety functions • Large dimensioned wheels (520 mm) a. • Clear miter setting up to 60° Semi-automatic function: 1. Clamp material 2. Saw starts 3. Rapid lowering to the start of the material or the same for series cutting cut 4. Saw band off 5. Raise the frame to just above the material 6. Open the vise

Condition: used, Technical details: balancing body max.: 800 kg balancing body diameter: 1250 mm Balancing revolution per minute: 190 - 3600 U/min bed length: 2600 mm voltage: 380 V/Hz Giodou Upp Tepfx Admjl drive power: 7,5 kw Weight approx.: 1,5 t dimension machine xH: 3,5 x 1,7 x 2,0 m dimensions electric cabinet: B:650 x T:250xH:800 mm Horizontal balancing machine The balancing machine is used to measure and balance the static or dynamic unbalance of rotors. Balancing body weight max. 800 kg with equal load distribution, i.e. 400 kg per bearing pedestal Power transmission by means of cardan shaft Bearing journal Ø min./max.: 16-95 / 95-180 mm Bearing distance center distance min. 125 mm and shaft end bearing center max. 2070 mm Measured speed: 1st gear = 190 - 650 rpm. 2nd gear = 400 - 1250 rpm 3rd gear = 700 - 2100 rpm. 4th gear = 1200 - 3600 rpm. 2 pick-up blocks whose displacement is manual over the entire bed Schenk measuring device with digital display and some accessories, e.g. many rotor shafts with different Ø and different rotor mounts, please ask! *

Condition: new, - Semi-automatic - Hydraulic - Infinitely adjustable band saw speed - Double miter - Hydraulic clamping of the miter setting Gijdpovkkl Tjfx Admel - Hydraulically adjustable sawing pressure - Fully hydraulic material clamping - Hydraulically adjustable clamping pressure - Cooling system - Automatic switch-off - Automatic switch-off of the machine at open cover, torn belt, reduced belt tension - Emergency stop - Documentation - 400V

Condition: new, ESP Top Loading Spray Washing Machines ESP series are designed for efficient cleaning of industrial parts with pressurized hot water plus a biodegradable detergent. The ESP range has very low operating cost and consumption, the body and structure is made entirely of corrosion free stainless steel material and heavy duty components. This type of machine is correct choice for cleaning oil, grease, production residues off the surface of parts and anticorrosive protection applications. The ESP range of spray washers are supplied with a stainless steel pump, nozzles, heaters and motorised basket as standard features. - Top opening gas spring assisted machine lid - Motorised stainless steel component basket - Stainless steel spray bar assemblies above, below and at the side - Integral fluid filtration system - Basket jog feature Gjdpfx Adjd Hbp Aemoil - Chemical & corrosion resistant stainless steel pump - Electrical powered fluid heating On customers demand these machines will also be built with a drying air blower. Depending on Top-Loader model: Basket diam. 820 - 1250 mm, loading weight 80 - 300 kg, spray pressure 1,8 - 3,5 bar (27 - 52,5 psi), heating: 4,5 - 12 kW, Options: digital timer and thermostat, oil skimmer, filtration, stainless steel loading car

Condition: used, Year of construction: 2020, sweeping width 942 mm working width Bodendüse: 700 mm tank Reinigung: 79 l tank Schmutzwasser: 83 l weight of the machine ca. 145 kg dimensions of the machine ca. 1,32 x 0,7 x 1,1 m - Exhibition machine and demonstration machine, like new- - Most compact ride-on scrubber-dryer from DiBO with 2 brushes - Possibility to dispense detergent: in ECO mode with constant Saving or automatic regulation of the machine depending on the speed of the machine Brush motors and suction: even less energy consumption, even more Smoothness - Display: large, multilingual, including hour counter, battery level and work programs - Memory card: allows the storage of battery charge cycles and Giodegvqzgepfx Admel Power consumption of the motor - CFS system: water distribution from the middle of the brush to avoid waste Avoid cleaning solution - SLS system: self-leveling electronic system to keep the brush always lies perfectly on the floor - EDD system: suction cup for the best results during drying and during Area performance was developed - Wheels: oil resistant - Extraction: 2 levels with fans and stainless steel shaft

Condition: new, Year of construction: 2025, These parts washers are designed for spray washing, using aqueous detergents at a temperature of 60°C maximum. All machines are made of AISI 304 stainless steel and they are models for one wash treatments. These machines function thanks to the basket’s motorized rotation around its vertical axis and they are suitable for washing small and medium-sized parts, with moderate weights. Gijdpjndcbyjfx Admsl

Condition: new, 1 brand-new semi-automatic high-performance horizontal bandsawing machine with double column guidance and 2° cutting inclination to the table support surface Make: HUVEMA / BEKA-MAK, Origin Turkey Model: BMSY 330 C Technical data: Sawing capacity 90° round 330 mm Sawing capacity 90° rectangular 360 x 330 mm Sawing capacity 90° square 330 mm Sawing capacity 45° round approx. 250 mm Sawing capacity 45° rectangular approx. 250 x 325 mm Gjdpfx Adofk Eu Nemjil Sawing capacity 45° square approx. 250 mm Size of the saw blade 5000 x 34 x1,1 mm Infinitely variable band speed 20 - 100 rpm. working height 635 mm Engine power 3 kW hydraulic motor 0,55 kW Dimensions L x W x H 2830 x 920 x 1630 mm Machine weight 1030 kg Accessories / Special features: - Semi-automatic double column band saw - Linear guides - 2° saw cut to the table support surface - Infinitely variable cutting speed via potentiometer on the control panel - Hydraulic vice - Hydraulic mechanical saw blade tensioning - Powerful drive motor - Sensitive cutting pressure regulation - Thermal overload protection - Optical height adjustment - Heavy duty gearbox - Coolant device - Feed roller conveyor 1200 mm - Chip brush - 1 pc. Bi-metal saw band - control panel - CE conform Delivery time: approx. 8 weeks after receipt of order Siegfried Volz Machine Tools Rüschebrinkstr. 151-153 D - 44143 Dortmund-Wambel

Condition: ready for operation (used), Max. workpiece thickness: 20mm, including one unused and originally packed set of blades. Giodpfsim Ixfsx Admsl

Condition: good (used), Roll diameter 483 mm Cut range Horizontal 457 mm Vertical 508 mm Cutting length 356 mm Godpfx Aju R Ryusdmjil Misc. Accessories MARCELS MASCHINEN AG

Condition: excellent (used), Year of construction: 2011, Technical data: Two-column design Cutting capacity: 700 x 520 mm Cutting diameter (round steel): max. 520 mm Cutting diameter (square steel): max. 520 x 520 mm Cutting diameter (rectangular steel): max. 520 x 520 mm CNC control: B&R PP 45 Hydraulic bundle clamping Hydraulic lowering Infinitely variable saw band speed Mobile control panel with digital display Saw blade dimensions: 6640 x 41 x 1.3 mm Cutting speed: 15 - 90 m/min Working height: 770 mm Motor power: 5.5 kW Dimensions (L x W x H): approx. 3500 x 3000 x 2500 mm Weight: approx. 5.0 t Accessories: 4 new saw blades Giedpoxlcpvofx Admsl Condition: Almost as-new condition The seller is not liable for typographical or data transmission errors. The machine's visual appearance, technology, and wear are consistent with its age; used machines are sold without any warranty.