CNC Machine Centres For Routing, Drilling And Edgebanding.

BIESSE ROVER B 1984 G EDGE

Condition: new, functionality: fully functional, machine/vehicle number: 8153336470, overall weight: 616 kg, volume flow: 399 m³/h, pressure (min.): 4 bar, pressure (max.): 13 bar, noise level: 67 dB, type of cooling: air, Equipment: documentation/manual, refrigerant dryer, type plate available, We are a company specializing in the compressed air industry for over 20 years. Professional level of service and high quality goods offered by our company - "proven" on the market - guarantee successful cooperation with you. We offer NEW screw compressor Atlas Copco GA37VSDs FF (variable speed with built-in dryer) Machine equipped with frequency converter (inverter), manufactured based on the latest technologies, which translates into greater efficiency and performance: On average 20% lower unit energy consumption (SER) than in previous models of the GA VSD series. Ecological and efficient VSD+ variable speed drive system reduces energy consumption by an average of 50% compared to models that operate at idle speed. Regardless of energy savings, efficiency (FAD) increases by up to 12%. Efficient fan motor (compliant with the ERP 2015 directive) reduces energy consumption and noise level. Superior Motor Efficiency (iPM) up to 94.5% exceeding IE3 efficiency levels. Built to work hard for your success. The industry-leading GA Series oil-injected rotary screw compressor delivers unmatched efficiency, high productivity and low cost of ownership – even in the harshest conditions. Technical data: capacity at 4 bar: 15.69- 13.75 l/s / 0.94-7.85 m3/min capacity at 7 bar: 15.67-129.35 l/s / 0.94-7.76 m3/min capacity at 10 bar: 15.68-110.79 l/s / 0.94-6.65 m3/min Max pressure 10 bar (13 Bar variant on request) Voltage 400 V Motor 37 kW Noise 67 dB(A) Weight 616 kg Motor with internal permanent magnets (IPM) Compression element Direct drive Innovative fan Pedpfx Akjwlp Hdoiegu Separator/oil filter with durable construction Electronic water drain valve that does not cause compressed air losses Controller Elektronikon Inlet valve VSDs module Manufacturer code: 8153336470 If you are not sure whether the device is right for you, you have not found the right compressor, CALL! We will advise you on the right choice of device. We invite you to familiarize yourself with our full offer.

Condition: excellent (used), Gantry (Portal) machine Movable panel (workpiece), movable working head (Horizontal position of the panel/workpiece) Numerical Control Power Control, Software WoodWOP Safety cabin (enclosure) of the working head and integral safety cabin (enclosure) of the machine In-feeding working table (panel support). Out-feeding working table (panel support) Panels (workpieces) feeding by No. 3 motorized belts - Feeding speed (m/min) max 130 ca. Minimum workpieces dimensions (X - Y - Z) mm 250 x 100 x 15 Maximum workpieces dimensions (X - Y - Z) mm 2500 x 1050 x 60 Motorized carpet to evacuate chips and wastes. Separate electric and command cabinet Total installed power: Kw 99 N° 2 WORKING GROUPS (TOP) - (SERVO-MOTOR X-Y-Z ): N° 4 Drilling heads (4 x Kw 2.3) with No. 10 vertical spindles each (total top spindles No. 40) N° 3 WORKING GROUPS (BOTTOM) - (SERVO-MOTOR X-Y-Z ) : N° 6 Drilling heads (6 x Kw 2.3) with No. 40 vertical spindles each (total bottom spindles No 240) Psdpfsgwbbqjx Akiegu N° 2 WORKING GROUPS (HORIZONTAL) N° 2 Drilling heads with horizontal spindles N° 21 Horizontal drilling spindles (Right Side) + N° 21 Horizontal drilling spindles (Left Side) N° 8 Dowel Inserting nozzle & glue injectors(Right side) + N° 8 Dowel Inserting nozzle (Left Side) N° 2 Storage tanks for automatic feeding of the dowels OPTIONAL: WIRELESS BAR CODE SCANNER

Condition: excellent (used), Angular sawing plant Numerical Control OSI Plus - Software Optiplanning N. 2 Pre-loading roller tables (mm) approx. 4500 x 2200 each Lifting table (mm) 4500 x 2200 Pedpjukhd Asfx Akiogu 1° Rear-pusher, with No. 5 clamps/grippers Turning device (rotating unit) at 90° 1° Panel saw (longitudinal) max. cutting width (mm) 4500 Max blade projection (mm) 152 Scoring Unit (max. diameter saw) mm approx. 215 Main Sawing Unit (max. diameter saw / power) mm 530 ( Kw 30) Adjustable speed of the saw carriage (m/min) 1 - 170 m/min Cutter for shredding trimmings 2° Rear-pusher, with No. 10 clamps/grippers 2° Panel Saw - Max cutting width mm 2200 Max blade projection (mm) 152 Scoring Unit (max. diameter saw) mm approx. 215 Main Sawing Unit (max. diameter saw / power) mm 530 (Kw 30) Adjustable speed of the saw carriage (m/min) 1 - 170 m/min No. 2 Front supporting tables with Air blowing system mm 2200 x 1500 Automatic unloader (bridge) for cut panels "RBO (BIESSE)" Mod. Lifter with 6 stacking stations

Condition: as good as new (ex-display), Year of construction: 2026, CNC Machining Centers Rover Multi Up M C S Working Area*: X = 3280 mm; Y = from 1580 to 1660 mm, depending on work conditions Z = 200 mm – 5-axis machining unit and drilling unit, with vacuum modules H = 74 mm Z = 245 mm – 5-axis machining unit and drilling unit, with vacuum modules H = 29 mm Workpiece Clearance*: Y = 1900 mm Axis Travel*: X = 3706 mm; Y = 2294 mm; Z1 = 515 mm; Z2 = 371 mm VACUUM SYSTEM Subdivision of the vacuum system into 2 working zones and 2 clamping zones in X. AUXILIARY VACUUM SYSTEM – 2 zones Allows clamping of workpieces using vacuum templates. Remote Control RM850 Rover Multi Up M C S Panel – Multi Purpose Regular Configuration 2 Compatible with the turret tool magazine with 16 positions and the side tool magazine with 12 positions. The tool magazines can also be retrofitted. Uninterruptible Power Supply (UPS) for machine PC. 6 ATS workpiece supports – 18 module carriers — 6 aluminium workpiece supports. The positioning of the workpiece supports is via linear guides with ball bearing slider blocks. Clamping is performed on the front and rear linear guides via pneumatic cylinders. Clamping is released by a push button located at the front of the workpiece support. — 18 module carriers, 132 x 132 x H 41.5 mm, with independent pneumatic clamping. The vacuum modules can be rotated in 15° increments on the module carriers; an ideal solution for shaped parts. — 18 covers for module carriers without template. SA (Set-Up Assistant) working table for tables up to 1550 mm. Supported manual positioning system with motion direction indicator and position indicator. — Sensors on each working table and along the X-axis of the working area. — Display of direction and position achieved for the carriage during positioning phase, mounted on each working table. According to the programmed configuration of the working tables, the system indicates the direction of movement for each working table and carriage, and confirms with a green LED and audible signal when the correct position is reached, with a tolerance of +/- 1.5 mm. Subdivision of the pneumatic system into 2 working areas in X. Machining unit with 5 interpolating axes, 13 kWp (17.4 HP), with HSK F63 adapter, liquid-cooled – 20,000 rpm Extraction hood with 12 NC-controlled positions for the 5-axis electrospindle. Flange for preparation of a 5-axis interpolating machining unit for mounting aggregates. Coolant system Additional Z-axis carrier for rear machining units, with independent Z-axis. Drilling head BH 24 L Side tool magazine with 12 positions, integrated into the machine bed. Turret tool magazine with 16 positions, installed directly on the X machining unit. Pgodpey Ehrxjfx Akiju HSK F63 tool adapter, equipped with a long integrated flange, for saw blades on the 5-axis head. Saw blade 300 mm, for tool holder. Hi-Tech tool set Complete set of tools for the acceptance test Consisting of the following 9 parts Replacement of standard PC with a high-performance PC. Digital device for measuring tool length up to 130 mm diameter. bSolid NC-HOPS 8 MacroCAM Rover 1. AV NC-HOPS MacroCAM 1. License WorkCenter suction cup proposal 5-Axis Simultaneous Material removal simulation 12-month warranty period Location: ex stock 54634 Bitburg - immediately available -

Condition: ready for operation (used), Year of construction: 2003, functionality: fully functional, travel distance X-axis: 4,035 mm, travel distance Y-axis: 1,720 mm, travel distance Z-axis: 380 mm, Equipment: chip conveyor, documentation/manual, We are offering this ready-to-use Weeke Optimat BHC 550 machining center, year of manufacture 2003. Manufacturer: Weeke Model: Optimat BHC 550 Year of manufacture: 2003 Condition: ready for operation Machine type: machining center If you have any questions or need more information, please feel free to send us a message or give us a call. Pgsdpox Nw Drjfx Akisu

Condition: excellent (used), Year of construction: 2003, Year of manufacture: 2003 Voltage: 400 V Frequency: 50 Hz Psdpfx Aotr A Evokisgu Weight: 3200 kg Number of axles: 3

Condition: excellent (used), Year of construction: 2018, functionality: fully functional, Double table machining center Working range X 2,590 mm Working range Y 2,260 mm Working range Z 400 mm Number of milling spindles 2 Liquid-cooled spindle Main motor 19.2 kW Max rotational speed 24,000 rpm Pjdpfxjuqw E Nj Akiogu Aggregate heads 4 C-axis Tool clamping system HSK-F63 Tool change positions central magazine 24 Tool change on each head from 12 positions Boring heads vert. 20 (for each head) Horizontal boring heads X 8 Horizontal boring heads Y 8 Blade for grooves in X, in Y 2 Platens Number 4 360 m³/h vacuum pumps T Jet system for chip blowing Nesting Manual labeling Bar code reader Tool length measurement Software BIESSE BIESSEWORKS ADVANCED, BIESSE B_NEST Weight 17,900 kg

Condition: used, machine/vehicle number: 008550, X axis working area: 4300 mm Y axis working area: 2205 mm Working Table: Flat table Main Electrospindle power: 13 KW Pgsdpfsz Eyycex Akiou Number of controlled axes: 5 axes Total number of drilling spindles: 28 Total number of tool changer positions: 16

Condition: not inspected (used), Number of sanding units 4 St sanding width 190 mm Sanding height max. 4-180 mm weight 4200 kg Hess Expert 4-belt single wood sanding machine machine will be checked by our technicians ----- Ø Grinding at the bottom/top Ø With 2 offset grinding units each (bottom and top) Ø Grinding units (bottom and top) connected in series according to the Dressing principle Ø Pre-sanding with coarse grit (calibrate) Ø Regrinding with fine grit (finish) Ø Central motorized height adjustment of the lower grinding units Ø Central motorized and synchronous height adjustment of the entire upper Grinding and brushing units including the upper transport units Ø Oscillating sanding belt utilization (during the sanding process) Ø Absolute power connection thanks to 5.5 KW motors and large dimensions drive drums Ø Oxide ceramic grinding shoe for - exact surface geometry - no adjustment work - permanent dimensional accuracy - completely maintenance and wear-free Basic structure: Stable, heavy welded construction made of strong-walled rectangular profiles additional, statically calculated reinforcements for optimal Vibration dampening. Staggered grinding units with large dimensions Belt drive drums for slip-free belt running. Two-point suction for direct and flying dust with sealing brushes and integrated sanding belt blow-off Device to increase the service life of the sanding belts. Grinding units in heavy steel plate construction as the basis for vibration-damped, quiet tape running. Absolutely backlash-free guides as ball linear sets hardened and ground shafts. Height adjustment of the grinding units via hardened and ground special linear guides as well as pre-tensioned ones Guide carriage. Permanent precision thanks to dust and dirt protection Ball linear sets and guide carriages. Large-sized pre-grinding rollers as contact rollers. Contact rollers and Sanding shoes in a balanced ratio to the sanding belt grain load. The large drive drums guarantee full transmission the 5.5 kW drive power of the grinding motors on the sanding belt. Therefore Slip-free, stable running and optimal heat dissipation. This makes it the strongest Chip removal possible. Automatic machine stop activation in the event of a belt break. Visual display on the control panel and via flashing lights on the machine. Sanding shoes for finish completely maintenance-free and wear-free made of oxide ceramic with optimal heat dissipation. Grinding belt tension via appropriately sized compression springs. Sanding belt relaxation for belt changing using a pneumatic device sensitive, distortion-free placement of new tapes. Upper grinding unit and brush device centrally motorized Height adjustable with digital display in the control panel for the motorized Grinding thickness adjustment. Brushing and finishing device, for better surface finish, integrated into the basic machine. Two special brush rollers 150 mm Æ arranged one above the other in synchronous function for advance thrust. Separate height adjustment of the brush rollers on precise Carriage guides for post-correction of wear. Additional transport roller for Pgodpfx Akot Tqy Eoiju Removal or further transport of the workpiece from the automatic grinding machine with the conveyor belt. Wooden guide in the inlet area for hard guide and bearings mounted on both sides pressure rollers. Safe transport of profiled workpieces on ca...

Condition: used, Edge banding machine Brand: Brandt Model: Profiline KDF 670-C Hiflex Single-sided edge banding machine in right-hand design, for hot melt gluing. Quick-change gluing unit for hot melt glue. Processing with PU glue granulate possible in accordance with glue specifications. Leak-proof glue reservoir under the glue roller. Precise glue application to the workpiece with glue roller, no adjustment of workpiece thickness necessary. Glue roller with selectable rotation direction for counter or forward feed. Glue temperature monitoring via electronic thermostat. Automatic reduction of glue temperature during work breaks. Infrared heating for hot melt reactivation. Automatic edge banding magazine for roll material and fixed lengths, including roll plate with a diameter of 800 mm and reinforced cutting shears for thick PVC/ABS, max. 3 x 45 mm. Standard equipment with edge banding and workpiece – distance monitoring with optical display. Stable pressure zone with driven, compressed air-loaded main pressure roller and 3 free-running post-press rollers. Standard equipment with automatic central lubrication for the transport chain. Motor-driven adjustment of overpressure. Control panel at the machine infeed. Technical data Pgodpfxsynhwfj Akieu Edge strip thickness: 0.4 – 12 mm Cutting tool: max. 3.0 x 45 mm or 0.8 x 65 mm Workpiece thickness: 8 – 60 mm Feed speed: 11 – 16 m/min (see below) When selecting edge banding thicker than 3 mm, the feed speed is automatically switched to 14 m/min. automatically to 14 m/min. When selecting form cutters, the feed rate is automatically switched to 11 m/min. Electrical connection: 400 V, 3-phase, 50 Hz Compressed air connection: 6 bar Connected load approx. 17 kW Machine length: 6,860 mm Full information about the machine can be found on our webpage burbagemaskin.se