Edgebander

BIESSE AKRON 1400

Condition: used, Year of construction: 2015, functionality: fully functional, BIESSE Edge Banding Machine AKRON 1440-A Automatic single-sided edge banding machines for gluing and processing straight edges with roll material (melamine, PVC, ABS, veneer) and strip material (solid wood, laminate, sliced veneer, etc.) • NC control with touch display • Automatic start of aggregate motors • Direct selection for second pass • Operating data acquisition • Software-guided maintenance TECHNICAL DATA Workpiece thickness 10-60 mm Workpiece thickness with MFU aggregate (depending on profile) 10-35/60 mm Edge height 14-64 mm Edge thickness – roll material 0.4-3 mm Edge thickness – strip material (*) 0.4-10 (12) mm Workpiece overhang 25 mm Minimum panel length 140 mm Minimum width (at 140 mm length) 85 mm Minimum width (at 250 mm length) 50 mm Feed speed 12 m/min Dust extraction* 8x connection Ø100 mm Bljdexzb Iiopfx Acvef Compressed air connection 7 bar Glue pot capacity 2 (approx.) kg * Depending on selected aggregates. - GLUING UNIT VC-511 Applies the hot-melt adhesive to the workpiece, feeds the edge to the workpiece, automatically cuts it from the roll, and presses it onto the workpiece, guaranteeing perfect positioning. - END TRIMMING UNIT IN-801 For trimming the front and rear edge overhangs with 0° to 15° angle. - 2-MOTOR MULTIFUNCTIONAL PROFILE MILLING UNIT AR02 E For corner rounding and profile milling of workpiece edges made of synthetic material up to a thickness of max. 3 mm. JOINTING CUTTER UNIT RT02 Joins the workpiece before glue application. Equipped with two 1.8 kW high-frequency motors at 12,000 rpm. SCRAPER UNIT RB02 For post-processing thick PVC/ABS edges. FLAT SCRAPER RC02 Aggregate for removing excess glue in the edge-to-panel area. Equipped with tracing rollers and a flat knife with engagement control. BUFFING UNIT SZ02 For cleaning and buffing the workpiece edge using fabric polishing discs. The unit automatically adapts to the workpiece thickness. ANTI-ADHESIVE SPRAY UNIT ADZ02 Precision application of anti-adhesive using injectors activated by numerical control. KIT PRO-GLUE The PRO-GLUE kit includes the following components: • TEKNO-GLUE system for optimal gluing through: - controlled pressure of the glue roller - automatic disengagement in case of feed stop - automatic ON/OFF of the glue unit • REVERSE system to switch the glue roller for co- or counter-rotation Electrical and mechanical preparation for the use of special glue pots for POLYURETHANE glue with machines equipped for EVA gluing. NC Axis for Fine Trimming Unit Kit for the automatic adjustment of tracing rollers and tools to match edge type and thickness. Adjustment takes place via the control system. Pair of multiprofile cutters for the fine trimming unit: 25-degree bevel, radius 2 mm + radius 1 mm plus straight profile for solid wood. NC Axis for Profile Milling Unit Kit for automatic adjustment of the tracer to match the edge thickness. Adjustment takes place via the control system. Function for processing only on the corners. NC Axis for Scraper Unit Kit for automatic adjustment of tracing rollers and tools to match edge type and thickness. Adjustment takes place via the control system.

Condition: used, Year of construction: 2017, Direct Numerical Control NC HOPS with Campus software Working range in X axis mm 3400 Working field in Y axis mm 1600 Working field in Z mm 300 Worktop with 6 adjustable bars No. 3 suction cups each work bar for holding the piece being processed N° 1 5-axis electrospindle, 10 KW, with automatic tool change, Hsk F63 type cones Boring head with 24 spindles as follows: N. 12 Y-axis vertical spindles N. 6 X-axis vertical spindles N. 4 horizontal spindles Y axis N. 2 X-axis horizontal spindles Automatic tool change system with 18 positions - positioned on the back of the machine Frontal protection and safety system with carpets and perimeter nets Automatic lubrication system Air conditioning system for the switchboard No. 1 vacuum pump Blodpowwiybsfx Acvof

Condition: used, Year of construction: 2017, Number of spindles 5 St. Working width 240 mm Working height 120 mm Bljdpfxjwwl Nls Acvof Length of the planing table 2500 mm Feed motor 4 kW Feed speed 6-36 m/min. Weight ca. 3500 kg control SCM Control 10 SCM Superset NT with workpiece return ----- The machine is in cleaning and completely checking process at the moment. Brief Summary: ----- - 5 spindles - Powerful motors - Left and upper spindles controlled for width and height - With workpiece return to the operator 1st spindle ----- First lower horizontal spindle Motor with brake 7.5 kW Diameter 40 mm Speed 6,000 rpm 2nd spindle ----- First right vertical spindle Motor with brake 7.5 kW Diameter 40 mm Speed 6,000 rpm T-set quick-clamping system 3rd spindle ----- First left vertical spindle Motor with brake 7.5 kW Diameter 40 mm Speed 6,000 rpm T-set quick-clamping system Electronic horizontal positioning / motorized width adjustment 4th spindle ----- First upper horizontal spindle Motor with brake 11.0 kW Diameter 40 mm Speed 6,000 rpm T-Set quick-clamping system Electronic radial positioning / motorized height adjustment 5th spindle ----- Second lower horizontal spindle Motor with brake 7.5 kW Diameter 40 mm Speed 6,000 rpm SCM Control 10 Includes workpiece return system Includes existing used planer heads. (Technical specifications according to the manufacturer - without guarantee!)

Year of construction: 1997, condition: good (used), - Working width (mm): 1300 - CSD system - Cross sanding unit - Longitudinal sanding unit - Shoe - Brush unit - Ionization Bjdpfx Ajidi Ivecvslf

Condition: good (used), Year of construction: 2012, functionality: fully functional, CNC machining center with edge banding for shaped workpieces Working dimensions for Y1 axis: X axis: 4,300 mm X axis pendulum operation: 1,620 mm Y axis: 1,320 mm Working dimensions for Y2 axis (edge processing): X axis: 3,300 mm X axis pendulum operation: 600 mm Y axis: 1,240 mm Work table: 8 ATS workpiece supports with 3 vacuum cups each 8 rear workpiece stops, program-controlled lowering, each mounted in one support 8 workpiece stops, 670 mm from rear, each mounted in one support 2 + 2 lateral workpiece stops 4 removable center stops 6 lift rails, pneumatically program-controlled lowering, for positioning heavy workpieces Automatic positioning of workpiece supports and vacuum cups via EPS (Electronic Positioning System) Automatic central lubrication Vacuum system divided into 2 separate work zones along the X axis Vacuum assist system for clamping templates Chip conveyor integrated into the machine table Vacuum pump 90 cbm/h Processing head equipment: Mounted on Z2 axis Drilling head BH 26 2L with: 16 vertical drilling spindles, individually selectable 2+2 horizontal drilling spindles in X direction 2+2 horizontal drilling spindles in Y direction Grooving saw, diameter 120 mm, fixed in X direction Grooving saw, diameter 120 mm, fixed in Y direction Milling spindle 13.2 kW (11 kW in S1 operation), HSK 63 F Mounted on Z1 axis Speed range 1,000 – 24,000 rpm Clockwise and counter-clockwise rotation C axis 360 degrees for adapter units Bledpfjxraimsx Acvef Cleaning nozzle for cleaning the milled edge before the edge banding process Tool magazine for 16 tools Edge banding unit for workpieces up to 60 mm thickness Edge banding unit CNC controlled, with 360 degree endless rotation Glue application for hotmelt adhesive Double pressure roller, interchangeable and can be switched off Heating lamp for preheating edge band material End trim unit to cut the edge band material at an 8-degree angle to the workpiece edge using circular saw blade Technical data: Plastic edge thickness 0.4 – 3 mm (*) Solid wood edge thickness 0.4 – 2 mm (*) (Best results achieved using wood edges with primer from 0.4 – 1.2 mm) Max. edge height 64 mm Panel thickness min. 14 mm, max. 60 mm Min. inside radius 18 mm for edge thickness less than 1 mm Min. inside radius 30 mm for edge thickness 2 mm Min. panel size for edge banding: 300 x 300 mm Min. size for edge banding of internal cutouts: 350 mm, with plastic edge max. 1 mm thickness and max. panel thickness 18 mm Edge magazine for 2 rolls, positioned outside the machine—this solution limits pendulum processing. Roll diameter for edge material: 800 mm Safety equipment: * Safety mats in front of the machine * Safety fence on the right with access door Without tools Control system: PC control with BIESSE WORKS ADVANCED Restart after emergency stop BIESSE WORKS office version Units: - Flush/radius trimming unit - Combination profile/flat scraper unit - Sawing unit

Condition: used, Year of construction: 2008, Used machine Year of manufacture: 2008 Edge Control control system with 18.5" touchscreen color monitor 16:9 Swiveling operator panel, Program storage, Motorized pressure bar adjustment, Feed via transport chain, Feed speed: 8-18 m/min Extendable workpiece support, Infeed fence with motorized adjustment Jointing unit 1961, Diamond jointing cutter for climb and counter rotation, Automatic adjustment to workpiece height Edge feed 1903 Pre-trimming up to 3 x 45 mm (depending on material) Glue application system 1905 Multi-System Automatic glue height adjustment with sensor nozzle, Pressure regulator for adjusting the cartridge contact pressure, Use of PUR adhesives possible, Pressure unit 1913 MOT, First roller driven End trimming unit 1918 with pneumatic adjustment End trim saw pneumatically swiveling, Multifunction unit 1824 MOT 4 with multifunction cutter radii 1,2,3 mm Corner copying unit 1832 Corner copying up to 3 mm edge thickness Blsdev Sv Enspfx Acvef Radius scraper 1929 MOT 2 With motorized adjustment of horizontal tracing rollers With pneumatic adjustment (top and bottom separate) Chip collection box for radius scraper, Surfacing scraper 1964 For removing glue residue for a clean glue line With extraction hoods Spray unit 1856 for infeed and outfeed area Buffing unit 1940 For finishing and edge polishing ----- Technical Data ----- Edge thickness roll material: 3 mm, Edge thickness strip material: 8 mm, Max edge thickness for corner copying: 3 mm, Workpiece thickness: 45 mm, Workpiece thickness for corner copying: 45 mm, Min. workpiece length: 180 mm, Feed speed: 8-18 m/min, Distance workpiece support: 470 mm, Support table diameter for edge material: 800 mm, End cut knife for coiled material up to: 3 mm, Heating time: 3.5 min, Jointing unit power: 2 x 2 kW, End trim saw power: 2 x 0.22 kW, Milling station power: 2 x 0.35 kW, Corner copying power: 0.22 kW, Extraction port jointing unit: 120 mm, Extraction port milling unit: 70 mm, Extraction port scraper unit: 70 mm, Total length: 5,350 mm, Dimensions (LxWxH): 5,350 x 1,669 x 1,940 mm Picture of operating hours taken from a recording in 2022 Availability: short term Location: Röllbach

Condition: excellent (used), Year of construction: 1995, Max. panel width 4400 mm Max. panel length 4300 mm Main saw blade projection 110 mm No of Grippers 8 Bljdpfx Acsmt Hhwjvef Front Loading Beam Panel Saws Max. saw blade projection 110 mm Front support tables no. tables 4 Control system NC 410 Safety standard CE mark Total installed power 20 KW

Condition: good (used), BRANDT highflex 1440 edgebanding machine well equipped, possibility to check before buying pre-cutters application of glue pneumatic pre-application guillotine pressure rollers pre-cutting balls top and bottom pre-milling unit 2 x earning-multifilling unit profile cyclin flat cyclin Blodpst Hxxpsfx Acvsf polisher machine has nc cutter control and pneumatic package max workpiece height 60mm max thickness of veneer in a roll 3mm feed rate max 14m/min Machine well maintained in very good condition

Condition: good (used), Year of construction: 2014, functionality: fully functional, System consisting of: PANEL SAW SELCO WNT 610 / 4500 x 2200 mm PC-BASED CONTROL SYSTEM Max. cutting length: 4,500 mm Max. saw blade projection (main saw): 95 mm Max. opening of clamping grippers: 90 mm Min. panel dimensions from rear: 1,830 x 915 mm Max. panel dimensions from rear: 3,100 x 2,200 mm Min. panel thickness for rear feeding: 3 mm Worktable height: 985 mm Main saw motor: 15 kW Main saw blade diameter: 380 mm Scoring saw motor: 2.2 kW Scoring saw blade diameter: 200 mm DIGISET: electronic adjustment of scoring saw to main saw QUICK CHANGE: fast blade change at the push of a button Saw carriage drive: 1 - 140 m/min Integrated side aligner in saw carriage: 0 - 4,200 mm Automatic measuring system for manual cuts Pusher extension from 5,500 to 7,800 mm 10 pneumatic clamping grippers on pusher with double fingers 3 front aligners 16 support roller tracks behind the machine table 4 air-cushion tables in front of the machine table, rounded, including movement device for table 2 Automatic ejection of end pieces beyond the cutting line Material support area under the pusher equipped with brush rollers for sensitive surfaces Machine table with air nozzles for sensitive surfaces Automatic device for monitoring the main saw blade consisting of a sensor that detects blade deflection and a system for measuring main spindle speed Software package: QUICKOPTI for optimizing cutting plans directly on the machine Blodpfxjxranpe Acvjf OSI PLUS INTERFACE VERSION OPTIPLANNING OPTIMIZATION SOFTWARE incl. hardware dongle, allows management of up to 10 users via network OS LABELLING: graphical editor on the machine control system with workpiece drawings, real-time label printing directly at the machine possible COMMUNICATION BETWEEN STORAGE FEED SYSTEM AND SELCO Industrial label printer at the machine STORAGE FEED SYSTEM RBO WINSTORE 2D STANDARD TRAVERSE 8000 MM Swiveling suction frame 0 - 180 degrees with controlled axis Panel alignment/squareness correction system consisting of 3 photocells mounted on pneumatic cylinders Panel weight detection via load cell mounted on the suction frame in the separation area, checks whether the specified weight value is within the expected range for this panel type. If not, the panel is set down again and the separation cycle restarts. Roller conveyor for stacking and unstacking: 4,200 mm Software: LINE SUPERVISOR with warehouse mapping, catalog, import of machining data from the optimizer, management of BOMs, plant control

Condition: used, Year of construction: 2014, CNC-controlled 5-axis machining center in gantry design for milling and drilling workpieces made of wood or wood-based materials. Console table with 8 consoles Vacuum system WoodWop package for AV-PC Blsdpsxvaymjfx Acvjf LED position display system for manual positioning of vacuum clamps and consoles. Positioning accuracy +/- 2.5 mm 5-axis main spindle 10 kW Drive5C. Cardanic 5-axis head for milling, drilling, and sawing at any angle. - Interface for HSK F 63 - Z-axis travel 450 mm - Liquid cooling with temperature monitoring - Spindle with hybrid bearings for maximum precision and long service life - Frequency inverter for electronic speed control 0–24,000 rpm - Maximum tool weight 6 kg incl. holder - Maximum tool length 230 mm from bottom edge of motor spindle - 18-position disc tool changer below Drilling head with 21 spindles, 2.2 kW Vertical spindles: 17 Max. drill diameter: 35 mm Total drill length: 70 mm Shank diameter: 10 mm Horizontal spindles: 4 One reinforced boring spindle with mount for grooving saw Max. drill diameter: 10 mm Total drill length: 70 mm Drill holder: 10 mm